Alcatel-Lucent Data Multiplexer Explore 1665 User manual

Alcatel-Lucent 1665
Data Multiplexer (1665 DMX) | Release 9.0
Installation Manual
365-372-304R9.0
CC109696781
Issue 2
July 2010

Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All other trademarks are the property of their respective owners.
The information presented is subject to change without notice. Alcatel-Lucent assumes no responsibility for inaccuracies contained herein.
Copyright © 2010 Alcatel-Lucent. All Rights Reserved.
Conformance statements
Federal Communications Commission (FCC) Part 15 Class A
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protections against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the user will be required to correct the interference at the user’s expense.
Security statement
In rare instances, unauthorized individuals make connections to the telecommunications network through the use of remote access features. In such an event, applicable tariffs
require that the customer pay all network charges for traffic. Alcatel-Lucent cannot be responsible for such charges and will not make any allowance or give any credit for charges
that result from unauthorized access.
Limited warranty
Alcatel-Lucent provides a limited warranty for this product. For more information, consult your local Alcatel-Lucent customer support team.

iii
Alcatel-Lucent 1665 DMX R9.0
365-372-304R9.0 Issue 2
July 2010
............................................................................................................................................................................................................................................................
Contents
About this document
Purpose ..................................................................................................................................................... xvii
Reason for reissue .................................................................................................................................... xvii
Intended audience .................................................................................................................................... xviii
How to use this document ....................................................................................................................... xviii
Safety information .......................................................................................................................................xx
Conventions used ....................................................................................................................................... xxi
Related information .................................................................................................................................. xxii
Technical support ..................................................................................................................................... xxii
How to order ............................................................................................................................................ xxiii
Packaging collection and recovery requirements .................................................................................... xxiii
Material content compliance ................................................................................................................... xxiii
1Safety
Laser safety ............................................................................................................................................... 1-1
Electrostatic discharge ESD considerations .............................................................................................. 1-3
Laser product classification ....................................................................................................................... 1-9
Alcatel-Lucent 1665 DMX optical specifications ................................................................................... 1-11
Part I: Physical installation and powering
2 Physical installation
Planning ..................................................................................................................................................... 2-2
Inspection .................................................................................................................................................. 2-3
Alcatel-Lucent 1665 DMX high-capacity shelf installation ..................................................................... 2-4
Heat baffle installation .............................................................................................................................. 2-8
Power cable and cable bracket installation .............................................................................................. 2-10
Fiber management installation (optional) ............................................................................................... 2-20
Installing the fiber ducts (optional) ......................................................................................................... 2-23
Alcatel-Lucent 1665 DMX high capacity shelf deep add-on fiber tray installation (optional) .............. 2-24
Alcatel-Lucent 1665 DMX high capacity shelf deep add-on fiber tray and 1-inch sideplate extension

............................................................................................................................................................................................................................................................
iv Alcatel-Lucent 1665 DMX R9.0
365-372-304R9.0 Issue 2
July 2010
............................................................................................................................................................................................................................................................
Contents
installation (optional) .............................................................................................................................. 2-26
3 Cable and fiber installation
Planning .................................................................................................................................................... 3-2
Connector references ................................................................................................................................. 3-4
Cable and optical fiber installation ........................................................................................................... 3-6
DS1 cable installation ............................................................................................................................... 3-7
DS3/EC1 and TMUX 48-port cable installation ..................................................................................... 3-14
12-DS3/EC1 and TMUX (LNW16 LNW18) cable installation ............................................................. 3-25
10/100BaseT backplane ethernet cable installation ................................................................................ 3-32
Ethernet cabling to SFP modules on circuit pack faceplates .................................................................. 3-36
IAO LAN and TCP/IP cable installation ................................................................................................. 3-39
Modem cable installation ........................................................................................................................ 3-43
Sync cable installation ............................................................................................................................ 3-45
Office alarm cable installation ................................................................................................................ 3-51
Miscellaneous (environmental) discrete telemetry cable installation ..................................................... 3-57
Main optical fiber installation (OC-12, OC-48, OC-192) ....................................................................... 3-61
Fiber installation for low-speed packs .................................................................................................... 3-62
1000Base-F and 100Base-F fiber installation ......................................................................................... 3-64
Fibre channel fiber installation ............................................................................................................... 3-66
CIT cable installation .............................................................................................................................. 3-67
Final operations ....................................................................................................................................... 3-70
4 Powering and initial circuit pack installation
Description ................................................................................................................................................ 4-1
Powering ................................................................................................................................................... 4-2
Circuit pack compatibility ......................................................................................................................... 4-5
Initial circuit pack installation ................................................................................................................. 4-10
Part II: Stand-alone installation tests
5 Software download and circuit pack installation
Software installation ................................................................................................................................. 5-2
Circuit pack installation ............................................................................................................................ 5-2
Use of WaveStar®CIT software ................................................................................................................ 5-6
Circuit pack firmware version verification ............................................................................................. 5-11

v
Alcatel-Lucent 1665 DMX R9.0
365-372-304R9.0 Issue 2
July 2010
............................................................................................................................................................................................................................................................
............................................................................................................................................................................................................................................................
Contents
Alcatel-Lucent 1665 DMX shelf initialization ........................................................................................ 5-13
Provision/enable/disable TCP/IP on an IAO LAN port .......................................................................... 5-13
Reset system date and time ..................................................................................................................... 5-16
Provision/enable/disable the Alcatel-Lucent 1665 DMX as a TL1 TCP/IP GNE .................................. 5-17
6 Installation tests
LBO software settings ............................................................................................................................... 6-2
Clearing alarms ......................................................................................................................................... 6-4
Local equipment and cross-connect tests .................................................................................................. 6-6
DS1 protection switching ........................................................................................................................ 6-10
DS1 cleanup procedures .......................................................................................................................... 6-14
DS3/EC1 and TMUX testing procedure ................................................................................................. 6-17
DS3 protection switching ........................................................................................................................ 6-23
DS3 cleanup procedures .......................................................................................................................... 6-26
LNW66 and LNW74 (10/100T) TX ethernet cabling testing ................................................................. 6-29
OC-3 (LNW37, LNW45, LNW55)/OC-12 (LNW49, LNW55)/OC-48 (LNW55, LNW62, LNW402) low-
speed SFP test procedure ......................................................................................................................... 6-34
OC-3 (low-speed) testing ........................................................................................................................ 6-35
OC-12 (low-speed) testing ...................................................................................................................... 6-39
OC-48 (low-speed) testing ...................................................................................................................... 6-44
OC-192 (low-speed) testing .................................................................................................................... 6-48
LED test ................................................................................................................................................... 6-51
Additional optical tests (optional) ........................................................................................................... 6-52
7 Operational tests
Tools, test equipment and accessories ....................................................................................................... 7-1
Office alarm test ........................................................................................................................................ 7-2
Automatic protection switching and alarm test ......................................................................................... 7-6
Manual switching tests .............................................................................................................................. 7-9
External timing verification ..................................................................................................................... 7-10
Miscellaneous (environmental) discrete telemetry test ........................................................................... 7-14
Modem connection test ........................................................................................................................... 7-17
Final operations ....................................................................................................................................... 7-19

............................................................................................................................................................................................................................................................
vi Alcatel-Lucent 1665 DMX R9.0
365-372-304R9.0 Issue 2
July 2010
............................................................................................................................................................................................................................................................
Contents
Part III: Network turn-up and testing
8 OC-3/12/48 ring setup and testing: integration procedures
Tools, test equipment and accessories ....................................................................................................... 8-1
Fiber installation ....................................................................................................................................... 8-2
Optical transmission test (OC-192, OC-48, OC-12) ................................................................................. 8-9
Automatic protection switching test ....................................................................................................... 8-10
Manual switching tests ............................................................................................................................ 8-12
Final operations ....................................................................................................................................... 8-14
9 WDMX setup and testing: integration procedures
Turn-up and test the LNW785 8-channel OMD ....................................................................................... 9-4
Turn up and test the LNW705 muxponder ............................................................................................... 9-6
Integrating the LNW705 into the LNW785 .............................................................................................. 9-9
Connecting the ring (Mains) to the WDMX ........................................................................................... 9-11
Removing provisioning and equipage from the LNW705 and LNW785 ............................................... 9-14
Part IV: Supplementary information and installation checklist
A Fiber cleaning
Equipment requirements and recommendations .......................................................................................A-2
Safety instructions .....................................................................................................................................A-3
Cleaning/inspecting optical connectors ....................................................................................................A-4
Cleaning pluggable optics modules ..........................................................................................................A-9
B Installing fiber connectors and LBOs
LBOs .........................................................................................................................................................B-2
Fiber connections ......................................................................................................................................B-4
C Backplane pin replacement
Pin and connector background ..................................................................................................................C-2
Repair kits and tools ..................................................................................................................................C-3
Simple repair methods ..............................................................................................................................C-4
Replacement methods ...............................................................................................................................C-5
D Fiber labeling
Fiber description .......................................................................................................................................D-1
Fiber labels ................................................................................................................................................D-3

vii
Alcatel-Lucent 1665 DMX R9.0
365-372-304R9.0 Issue 2
July 2010
............................................................................................................................................................................................................................................................
............................................................................................................................................................................................................................................................
Contents
E Pluggable transmission module installation
Pluggable transmission modules (PTM) ...................................................................................................E-1
Install pluggable transmission modules ....................................................................................................E-3
Pluggable transmission modules .............................................................................................................E-10
GL Glossary
Acronyms and abbreviations ..................................................................................................................GL-1
Terms and definitions ...........................................................................................................................GL-15
IN Index

............................................................................................................................................................................................................................................................
viii Alcatel-Lucent 1665 DMX R9.0
365-372-304R9.0 Issue 2
July 2010
............................................................................................................................................................................................................................................................
Contents

ix
Alcatel-Lucent 1665 DMX R9.0
365-372-304R9.0 Issue 2
July 2010
............................................................................................................................................................................................................................................................
List of figures
1Safety
1-1 Static control wrist strap ............................................................................................................... 1-5
I-1 Alcatel-Lucent 1665 DMX high-capacity shelf backplane ...........................................................I-2
2 Physical installation
2-1 Alcatel-Lucent 1665 DMX high-capacity shelf mounting bracket positions — 23-inch frame .. 2-5
2-2 Alcatel-Lucent 1665 DMX high-capacity shelf mounting bracket positions — 19-inch frame .. 2-6
2-3 Typical Alcatel-Lucent 1665 DMX high-capacity shelf bay mounting arrangements ................ 2-7
2-4 Heat baffle position ...................................................................................................................... 2-9
2-5 Cable brackets ............................................................................................................................ 2-11
2-6 Power connector mounting positions ........................................................................................ 2-13
2-7 Alternating power cable routing ................................................................................................. 2-14
2-8 Power connection ....................................................................................................................... 2-15
2-9 Power cable routing with cable bracket ..................................................................................... 2-16
2-10 Power cable routing without cable bracket ................................................................................ 2-17
2-11 Deep add-on fiber tray ................................................................................................................ 2-26
2-12 Cover, fiber tray, and edging grommet ....................................................................................... 2-27
2-13 Sideplate extensions ................................................................................................................... 2-28
2-14 Deep add-on fiber tray with edging grommet ............................................................................ 2-29
2-15 Kit ID label ................................................................................................................................. 2-30
2-16 Flush front cover ........................................................................................................................ 2-30
3 Cable and fiber installation
3-1 Connector types and pinouts ........................................................................................................ 3-5
3-2 DS1 cable installation .................................................................................................................. 3-9
3-3 DS1 cable routing ....................................................................................................................... 3-10
3-4 DS3/EC1 and TMUX cable installation ..................................................................................... 3-16
3-5 DS3/EC1 and TMUX cable routing ........................................................................................... 3-16
3-6 12-port DS3/EC1 and TMUX cable installation ....................................................................... 3-27
3-7 12-DS3/TMUX cable routing .................................................................................................... 3-28
3-8 10/100BaseT cable installation .................................................................................................. 3-33

............................................................................................................................................................................................................................................................
xAlcatel-Lucent 1665 DMX R9.0
365-372-304R9.0 Issue 2
July 2010
............................................................................................................................................................................................................................................................
List of figures
3-9 Ethernet cable routing to faceplate SFP modules ...................................................................... 3-37
3-10 LAN cable installation to front of Alcatel-Lucent 1665 DMX high-capacity shelf .................. 3-40
3-11 IAO LAN/TCP-IP cable installation to rear of
Alcatel-Lucent 1665 DMX high-capacity shelf ......................................................................... 3-41
3-12 Modem cable installation .......................................................................................................... 3-44
3-13 Sync cable with molded DB9 connector installation ................................................................. 3-47
3-14 Sync cable with wire-wrap connector installation ..................................................................... 3-48
3-15 Office alarm cable installation ................................................................................................... 3-53
3-16 Office alarm mult cable installation ........................................................................................... 3-55
3-17 Miscellaneous discrete cable installation .................................................................................. 3-58
3-18 CIT cable installation ................................................................................................................. 3-68
4 Powering and initial circuit pack installation
4-1 Power connections on Alcatel-Lucent 1665 DMX high-capacity shelf backplane ..................... 4-3
4-2 Alcatel-Lucent 1665 DMX high-capacity shelf .......................................................................... 4-9
6 Installation tests
6-1 Optical test set arrangement ....................................................................................................... 6-54
6-2 Optical test arrangement RX fiber moved ................................................................................. 6-55
7 Operational tests
7-1 Alcatel-Lucent 1665 DMX shelf backplane .............................................................................. 7-13
7-2 Miscellaneous (environmental) discrete functions ................................................................... 7-16
A Fiber cleaning
A-1 Cleaning the ferrule endface ........................................................................................................A-5
A-2 CleTop cleaner .............................................................................................................................A-6
A-3 Acceptability criteria for fiber cleaning .....................................................................................A-8
B Installing fiber connectors and LBOs
B-1 LC-Type Connector Ports on Circuit Pack ..................................................................................B-2
B-2 LC-Type LBO ..............................................................................................................................B-3
B-3 LC-type LBO inserted Into LC-type connector port ...................................................................B-3
B-4 Removing LC-type LBO From LC-type connector port .............................................................B-4
B-5 LC-Type fiber connector ..............................................................................................................B-5
B-6 LC-type fiber connection .............................................................................................................B-5
E Pluggable transmission module installation
E-1 Pluggable transmission module with dust plug (optical PTMs only) .......................................... E-3

xi
Alcatel-Lucent 1665 DMX R9.0
365-372-304R9.0 Issue 2
July 2010
............................................................................................................................................................................................................................................................
............................................................................................................................................................................................................................................................
List of figures
E-2 Examples of dust plugs ................................................................................................................E-3
E-3 Module types ................................................................................................................................E-4
E-4 Latch type 3 (opened and closed) .................................................................................................E-6
E-5 Latch type 4, 5, 6, 7 and 8 (opened and closed) ...........................................................................E-7
E-6 Insert pluggable transmission module into socket .......................................................................E-8

............................................................................................................................................................................................................................................................
xii Alcatel-Lucent 1665 DMX R9.0
365-372-304R9.0 Issue 2
July 2010
............................................................................................................................................................................................................................................................
List of figures

xiii
Alcatel-Lucent 1665 DMX R9.0
365-372-304R9.0 Issue 2
July 2010
............................................................................................................................................................................................................................................................
List of tables
About this document
1-1 1665 DMX documentation set .................................................................................................... xxii
1Safety
1-1 Laser classes ............................................................................................................................... 1-10
1-2 Alcatel-Lucent 1665 DMX optical circuit pack laser safety specifications ............................... 1-11
1-3 Alcatel-Lucent 1665 DMX optical PTM laser safety specifications ......................................... 1-12
1-4 Dispersion-limited receiver sensitivity for OC-192 DWDM PTMs .......................................... 1-22
I-1 Tool, test equipment and accessories required ..............................................................................I-3
I-2 Computer requirements .................................................................................................................I-6
I-3 Installation acceptance checklist ...................................................................................................I-7
2 Physical installation
2-1 Cable requirements and options ................................................................................................... 2-3
2-2 Power cable positioning ............................................................................................................ 2-12
2-3 Power cable assemblies .............................................................................................................. 2-19
2-4 Power connections ...................................................................................................................... 2-20
3 Cable and fiber installation
3-1 Cable requirements and options ................................................................................................... 3-3
3-2 DS1 cable assemblies ................................................................................................................. 3-11
3-3 DS1 transmission connections ................................................................................................... 3-12
3-4 DS3 connections for each function groups ................................................................................ 3-15
3-5 DS3 Cable with 24 DS3 with BNC (LNW16/LNW18/LNW19B/LNW20) .............................. 3-18
3-6 DS3 Cable with 24 DS3 w/o BNC(LNW16/LNW18/LNW19B/LNW20)) .............................. 3-19
3-7 Miscellaneous DS3 Cables (LNW16/LNW18/LNW19B/LNW20) ........................................... 3-20
3-8 DS3/EC1 and TMUX transmission connections ........................................................................ 3-22
3-9 Table DS3 Cable assemblies with BNC with 12-DS3 (LNW16/LNW18) ................................ 3-29
3-10 DS3 Cable assemblies w/o BNC with 12-DS3 (LNW16/LNW18) ........................................... 3-30
3-11 12-port DS3/EC1 and TMUX transmission connections ........................................................... 3-31
3-12 10/100BaseT ethernet cable assemblies ..................................................................................... 3-34
3-13 10/100BaseT ethernet connections ............................................................................................ 3-35

............................................................................................................................................................................................................................................................
xiv Alcatel-Lucent 1665 DMX R9.0
365-372-304R9.0 Issue 2
July 2010
............................................................................................................................................................................................................................................................
List of tables
3-14 GbE ethernet cables ................................................................................................................... 3-38
3-15 LAN 10BaseT cable assemblies ................................................................................................ 3-42
3-16 LAN 10BaseT cross-over cable connections ............................................................................. 3-43
3-17 LAN 10BaseT straight-through cable connections .................................................................... 3-43
3-18 Modem cable assemblies ........................................................................................................... 3-45
3-19 Modem cable connections .......................................................................................................... 3-45
3-20 Synchronization cable assemblies (SYNC1 and SYNC2) ......................................................... 3-50
3-21 Synchronization cable (DS1 timing reference) connections ...................................................... 3-51
3-22 Office alarm cable assemblies .................................................................................................... 3-56
3-23 Office alarm connections ........................................................................................................... 3-57
3-24 Miscellaneous discrete cable assemblies ................................................................................... 3-59
3-25 Miscellaneous (environmental) discrete telemetry connections ................................................ 3-60
3-26 CIT Cable Assembly .................................................................................................................. 3-68
3-27 Standard CIT cable connections ................................................................................................ 3-69
3-28 RJ-45 to DB-9 connector connections ....................................................................................... 3-69
4 Powering and initial circuit pack installation
4-1 Alcatel-Lucent 1665 DMX high-capacity shelf power supply requirements .............................. 4-2
4-2 R9.0 circuit pack compatibility .................................................................................................... 4-6
4-3 OC-12 mains with 12 STS-1s of vt switch fabric ........................................................................ 4-8
4-4 OC-48/OC-192 Mains with 48 STS-1s of vt switch fabric .......................................................... 4-8
4-5 OC192 circuit packs with 48 STS-1s of vt switch fabric ............................................................. 4-8
4-6 OC192 circuit packs with 192 STS-1s of vt switch fabric (VLF) ............................................... 4-8
4-7 Main Switch Pack (no optics) with 96 STS-1s of vt switch fabric .............................................. 4-8
6 Installation tests
6-1 Cable lengths (feet) ...................................................................................................................... 6-3
6-2 DS1 Cross-Connections ............................................................................................................. 6-14
6-3 DS3 cross-connections ............................................................................................................... 6-27
6-4 Transmission rate ....................................................................................................................... 6-54
7 Operational tests
7-1 Office alarm connections ............................................................................................................. 7-3
7-2 Miscellaneous (environmental) discrete telemetry connections ................................................ 7-16
8 OC-3/12/48 ring setup and testing: integration procedures
8-1 Attenuation Table ......................................................................................................................... 8-5

xv
Alcatel-Lucent 1665 DMX R9.0
365-372-304R9.0 Issue 2
July 2010
............................................................................................................................................................................................................................................................
............................................................................................................................................................................................................................................................
List of tables
8-2 Attenuation table (Pluggable Transmission Modules) ................................................................. 8-6
9 WDMX setup and testing: integration procedures
9-1 Channel/port assignments .......................................................................................................... 9-17
9-2 XM10G/8 PTM port guidelines .................................................................................................9-18
9-3 Attenuation table ........................................................................................................................ 9-19
9-4 Attenuation table (pluggable transmission modules) ................................................................. 9-20
A Fiber cleaning
A-1 Required and recommended equipment and materials ............................................................... A-2
C Backplane pin replacement
C-1 Backplane locations of METRAL pins ........................................................................................C-3
C-2 Metral pins ...................................................................................................................................C-3
D Fiber labeling
E Pluggable transmission module installation
E-1 Alcatel-Lucent approved pluggable transmission modules .......................................................E-11

............................................................................................................................................................................................................................................................
xvi Alcatel-Lucent 1665 DMX R9.0
365-372-304R9.0 Issue 2
July 2010
............................................................................................................................................................................................................................................................
List of tables

xvii
Alcatel-Lucent 1665 DMX R9.0
365-372-304R9.0 Issue 2
July 2010
............................................................................................................................................................................................................................................................
About this document
Purpose
This document provides the information and procedures necessary to install, self-test and
turn up the Alcatel-Lucent 1665 Data Multiplexer (Alcatel-Lucent 1665 DMX).
Reason for reissue
This document is being reissued to include information about new features and hardware
associated with R9.0 including:
•LNW87 Private Line Ethernet circuit pack supports up to four PTM-based FE or GigE
optical/electrical interfaces. All FE and GigE optical and electrical PTMs currently
supported by Alcatel-Lucent 1665 DMX are compatible with the LNW87.
•LNW203 OC-12 Main circuit pack supports a single PTM-based OC-12 signal. All
OC-12 PTMs currently supported by Alcatel-Lucent 1665 DMX are compatible with
the LNW203.
•LNW504 OC-48/OC-192 VLF Main circuit pack supports four PTM-based OC-48
signals or four PTM-based OC-192 signals. All OC-48 and OC-192 PTMs currently
supported by Alcatel-Lucent 1665 DMX are compatible with the LNW504.
•LNW603 OC-192 circuit pack supports a single PTM-based low-speed OC-192
signal. All OC-192 PTMs currently supported by Alcatel-Lucent 1665 DMX are
compatible with the LNW603.
•100BASE-FX-I1 and 100BASE-ZX-I1 FE PTMs support on LNW74 , LNW87, and
LNW170.
•OC3X12X48-LR1-I1 and OC3X12X48-IR1-I1 multi-rate PTM for LNW82 and
LNW55.
•G.8032 Ethernet Ring Protection (ERP) support on the LNW170.
•SSH File Transfer Protocol (SFTP) supported for software download, database
backup, and database restoration.
•SNMP v3 Monitoring (gets and traps).
•RADIUS authentication support for user login.

............................................................................................................................................................................................................................................................
xviii Alcatel-Lucent 1665 DMX R9.0
365-372-304R9.0 Issue 2
July 2010
............................................................................................................................................................................................................................................................
About this document
•Configuration for SONET and SDH on a per port basis on VLF packs (LNW45,
LNW49, LNW55).
•Single TID between shelves (up to 12) for DCS applications.
Intended audience
This installation manual is intended to provide individuals and customers the information
and procedures necessary to install, self-test and turn up the Alcatel-Lucent 1665 DMX
system.
This manual is not a service or operations manual. For any activities involving circuit turn-
up, regular maintenance, or trouble analysis, see
•Alcatel-Lucent 1665 Data Multiplexer (DMX) User Operations Guide, 365-372-301
•Alcatel-Lucent 1665 Data Multiplexer (DMX) Alarm Messages and Trouble Clearing
Guide, 365-372-302
How to use this document
This manual is divided into the following sections with a brief description of the contents
of each major part/chapter/appendix:
About this document
This chapter describes the purpose, intended audience, reason for reissue, and
organization of this document. This section references related documentation and explains
how to order, make comments or recommend Preliminaryhanges to this document.
Chapter 1, “Safety”
This chapter provides important safety instructions for Alcatel-Lucent 1665 DMX.
Part I: “Physical installation and powering”
Part I provides a checklist to ensure that all necessary procedures have been completed.
Use of the installation checklist is required to ensure a quality installation, all completed
tasks should be checked off and those not completed should be duly noted as to the reason
why. This checklist should be turned in as part of your job complete paperwork.
Chapter 2, “Physical installation”
This section provides physical installation instructions for Alcatel-Lucent 1665 DMX
power cabling and fiber management.

............................................................................................................................................................................................................................................................
Alcatel-Lucent 1665 DMX R9.0
365-372-304R9.0 Issue 2
July 2010
xix
............................................................................................................................................................................................................................................................
About this document
Chapter 3, “Cable and fiber installation”
This chapter provides the information and procedures for installing and cabling the
Alcatel-Lucent 1665 DMX system. It provides the additional cabling information needed
for the added DS1, DS3 capacity and Ethernet capacity.
Chapter 4, “Powering and initial circuit pack installation”
This chapter provides information for verifying that the shelf is being supplied with the
proper power and provides instructions for circuit pack installation.
Part II: “Stand-alone installation tests”
Chapter 5, “Software download and circuit pack installation”
Software download and circuit pack installation is covered in this chapter.
Chapter 6, “Installation tests”
This chapter verifies proper transmission cabling installation and functionality.
Chapter 7, “Operational tests”
This chapter provides instructions to test protection switching and the non-transmission
cabling. This section is not intended to replace acceptance test procedures.
Part III: “Network turn-up and testing”
Chapter 8, “OC-3/12/48 ring setup and testing: integration procedures”
This chapter provides the tests to verify proper ring fiber cabling and protection switching.
Chapter 9, “WDMX setup and testing: integration procedures”
This chapter is used to verify WDMX connectivity between Alcatel-Lucent 1665 DMX
nodes. The chapter includes the LNW785 8 channel Optical Multiplexer Demultiplexer
(OMD) and the LNW705 XM10G/8 Muxponder circuit packs. It is not intended to replace
acceptance test procedures.
Part IV: “Supplementary information and installation checklist”
Appendix A, “Fiber cleaning”
This appendix describes the Lucent recommended method for the cleaning and inspection
of optical connectors using specific tools and materials that have been proven to be
effective in the assembly and testing of optical equipment.

............................................................................................................................................................................................................................................................
xx Alcatel-Lucent 1665 DMX R9.0
365-372-304R9.0 Issue 2
July 2010
............................................................................................................................................................................................................................................................
About this document
Appendix B, “Installing fiber connectors and LBOs”
This appendix provides procedures for installing and removing the types of Line Build
Out (LBO) units and fiber connectors onto input and output ports found on the Alcatel-
Lucent 1665 DMX circuit packs.
Appendix C, “Backplane pin replacement”
This appendix provides information and the procedures used when a pin or blade on the
Alcatel-Lucent 1665 DMX backplane has been bent or broken.
Appendix D, “Fiber labeling”
This appendix provides a description of how to label the fiber.
Appendix E, “Pluggable transmission module installation”
Provides examples of various SFP installation.
Glossary
The Glossary provides definitions for telecommunication acronyms and terms.
Index
The Index supplies users with specific subjects and corresponding page numbers to find
necessary information.
Safety information
This information product contains hazard statements for your safety. Hazard statements
are given at points where safety consequences to personnel, equipment, and operation may
exist. Failure to follow these statements may result in serious consequences.
Safety precautions
Adhere to the following safety precautions:
•Electrostatic discharge (ESD)
You must be properly grounded when making contact with the Alcatel-Lucent 1665 Data
Multiplexer (1665 DMX) frame and handling circuit packs. Wrist strap ground cords
should be routinely tested for the minimum 1-megohm resistance.
•Plug-in storage
Circuit packs should be stored in static-safe packaging or in a grounded cabinet.
For additional safety precautions, please see the Alcatel-Lucent 1665 Data Multiplexer
(DMX) User Operations Guide, 365-372-301.