Alcatel-Lucent 9764 Series User manual

Alcatel-Lucent 9764 cMCO LTE
9764 Compact Metro Cell Outdoor B7 2x2W V1.1
9764 Compact Metro Cell Outdoor B3 2x5W V1.2
September 2015
Alcatel-Lucent –Proprietary
Use pursuant to applicable agreements

Legal notice
Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All other trademarks are the property of their respective
owners.
The information presented is subject to change without notice. Alcatel-Lucent assumes no responsibility for inaccuracies contained herein.
Copyright © 2015 Alcatel-Lucent. All rights reserved.
Contains proprietary/trade secret information which is the property of Alcatel-Lucent and must not be made available to, or copied or used by anyone outside
Alcatel-Lucent without its written authorization.
Not to be used or disclosed except in accordance with applicableagreements.
Alcatel-Lucent –Proprietary
Use pursuant to applicable agreements

....................................................................................................................................................................................................................................
3
Alcatel-Lucent 9764 CMCO
Alcatel-Lucent –Proprietary
Use pursuant to applicable agreements
Contents
About this document
Purpose ...................................................................................................................................................... xiii
Intended audience ...................................................................................................................................... xiii
Supported systems ..................................................................................................................................... xiii
How to use this document.......................................................................................................................... xiii
Safety information ..................................................................................................................................... xiv
Prerequisites .............................................................................................................................................. xiv
Conventions used....................................................................................................................................... xiv
Related information ................................................................................................................................... xvi
Document support.................................................................................................................................... xviii
Technical support .................................................................................................................................... xviii
How to order............................................................................................................................................ xviii
How to comment ..................................................................................................................................... xviii
1 Safety statements
Overview ................................................................................................................................................... 1-1
Structure of safety statements.................................................................................................................... 1-2
Safety......................................................................................................................................................... 1-4
Safety - specific hazards ............................................................................................................................ 1-5
Product safety ............................................................................................................................................ 1-9
2 Product overview
Overview ................................................................................................................................................... 2-1
Functional description ............................................................................................................................... 2-2
Physical description................................................................................................................................... 2-4

Supported installation options..................................................................................................................2-11
Hardware and ancillary items...................................................................................................................2-17
3 Pre-installation
Overview ....................................................................................................................................................3-1
Pre-installation information........................................................................................................................3-2
Installation clearances ................................................................................................................................3-4
Pole mount installation requirements.........................................................................................................3-5
Wall mount installation requirements.........................................................................................................3-7
4 Installation
Overview ....................................................................................................................................................4-1
Pre-installation cabling
Overview ....................................................................................................................................................4-3
Procedure 4-1: Ethernet cabling - fiber optic .............................................................................................4-4
Procedure 4-2: Ethernet cabling - electrical .............................................................................................4-11
Installation
Overview ..................................................................................................................................................4-20
Procedure 4-3: Pole mount the 9764 CMCO ...........................................................................................4-21
Procedure 4-5: Wall mount the 9764 CMCO ...........................................................................................4-28
5 Cabling
Overview ....................................................................................................................................................5-1
Procedure 5-1: Connect ground cable ........................................................................................................5-2
Procedure 5-2: Connect RF antennas .........................................................................................................5-4
Procedure 5-3: Connect GPS antenna ........................................................................................................5-8
Procedure 5-4: Connect power cable........................................................................................................5-13
6 Post-installation
Overview....................................................................................................................................................6-1
Procedure 6-1: Final installation activities and checks .............................................................................. 6-2

A LED state description
Overview ..................................................................................................................................................................................... C-1
LED status for 9764 CMCO ................................................................................................................................................ C-2
B Product conformance statements
Overview ..................................................................................................................................................................................... D-1
European Union
Introduction ................................................................................................................................................................................ D-2
CE marking ................................................................................................................................................................................ D-3
EMC and radio spectrum compliance .............................................................................................................................. D-4
Product safety and RF exposure ......................................................................................................................................... D-5
Eco-environmental statements .......................................................................................................................................... D-10

About this document
Purpose
The purpose of this document is to provide hardware installation instructions for the
Alcatel-Lucent 9764 Compact Metro Cell Outdoorproduct.
Procedures are provided for mounting, grounding, powering, and cablingthe
Alcatel-Lucent 9764 Compact Metro Cell Outdoorproduct.

Intended audience
The audience for this document is Hardware Installation personnel
relating to the Alcatel-Lucent 9764 Compact Metro Cell Outdoorproduct.
Supported systems
This document applies to the following 9764 CMCO products:
 Alcatel-Lucent 9764 Compact Metro Cell Outdoor B7 2x2W
 Alcatel-Lucent 9764 Compact Metro Cell Outdoor B3 2x5W
How to use this document
Start with the first chapter and work through the manual to the end. Once you have
done this, you will have carried out the hardware installation completely and in the
proper sequence.

About this document
....................................................................................................................................................................................................................................
Prior to installing the equipment, the installer should be familiar with thesafety
precautions, warnings, and product conformancestatements.
Safety information
For your safety, this document contains safety statements. Safety statements are givenat
points where risks of damage to personnel, equipment, and operation may exist. Failure to
follow the directions in a safety statement may result in serious consequences.
Prerequisites
None
Conventions used
Vocabulary conventions
In this document the Alcatel-Lucent 9764 Compact Metro Cell Outdoor is also referred to
as the 9764 CMCO.
Typographical conventions
The typographical conventions used in this document are described in the following table.
Appearance
Description
emphasis
Text that is emphasized
document titles
Titles of books or other documents
graphical user interface text
Text that is displayed in a graphical user
interface
variables
A value or command-line parameter that the
user provides
Technical conventions
Lengths and other measurements are given in metric units, with non-metric units given as
equivalents for use in non-metric markets.
For manufactured parts, the following system of conventions is used:
 Metric sizes of nuts, bolts, flat washers, and lock washers are identified by an
uppercase letter M followed immediately by a size in millimeters (example: M10)
 American fractional sizes of nuts, bolts, anchor bolts, and washers are identified by a
number followed immediately by a double apostrophe (example: 3/8"). In the case of
lengths measured in feet, "2 feet" is used rather than "2'" so that the singleapostrophe
is not overlooked.

About this document
....................................................................................................................................................................................................................................
The illustrations in this document do not contain all details and exceptions, but are rather
intended to highlight main points. Dimensions are usually shown in millimeters, with
inches in parenthesis. As an example, 680.0 (26.77) equals 680 millimeters or26.77
inches.
Wire gauges are specified in metric units. Equivalent sizes in the American Wire Gauge
(AWG) system are given in the following table.
Standard cross-sections and wire diameter of round copper conductors
The following table is from CEI/IEC 60947-1:2004, Table 1, Standard cross-sectionsof
round copper conductors and approximate relationship between mm2 and AWG/kcmil
sizes for reference. Additional wire sizes are included in this information product as
appropriate for the topic.
ISO rated cross-sectional area (mm2 )
AWG/kcmil size
0.2
24
0.34
22
0.5
20
0.75
18
1
-
1.5
16
2.5
14
4
12
6
10
10
8
16
6
25
4
35
2
-
1
50
0 (1/0)
70
00 (2/0)
95
000 (3/0)
-
0000 (4/0)
120
250 kcmil
150
300 kcmil
185
350 kcmil
-
400 kcmil

Use pursuant to applicable agreements
SO rated cross-sectional area (mm2 )
AWG/kcmil size
240
500 kcmil
300
600 kcmil
NOTE: The dash, when it appears, counts as a size when considering connecting capacity (see
7.1.7.2 in the standard).
Safety training in the following areas is required for personnel installing Alcatel-Lucent
products and associated equipment:
 Hazard Communication
 Lift Safety
 Hoist Safety
 Lock Out/Tag Out
 Accident/Incident Reporting.

Use pursuant to applicable agreements
1 Safety statements
Overview
Purpose
This chapter provides general information on the structure of safety instructionsand
summarizes general safety requirements.

Use pursuant to applicable agreements
General safety and residual risk
The equipment has been developed in line with state-of-the-art technology and conforms
with current national and international safety requirements.
The equipment is considered safe during normal operation when safe working practices
are complied with. However, hazards may arise if procedures are not followed correctly
or safe working practices are not complied with.
Contents
Structure of safetystatements
1-2
Safety
1-4
Safety - specific hazards
1-5
Product safety
1-9

Use pursuant to applicable agreements
Safety statements Structure of safety statements
Structure of safety statements
Overview
This topic describes the components of safety statements that appear in this document.
General structure
Safety statements include the following structuralelements:
CAUTION
Lifting hazard
Lifting this equipment by yourself can result in injury
due to the size and weight of the equipment.
Always use three people or a lifting device to transport
and position this equipment. [ABC123]
Item
Structure element
Purpose
1
Safety alert symbol
Indicates the potential for personal injury
(optional)
2
Safety symbol
Indicates hazard type (optional)
3
Signal word
Indicates the severity of the hazard
4
Hazard type
Describes the source of the risk of damage or
injury
5
Safety message
Consequences if protective measures fail
6
Avoidance message
Protective measures to take to avoid the hazard
7
Identifier
The reference ID of the safety statement
(optional)

....................................................................................................................................................................................................................................
1-3
Alcatel-Lucent –Proprietary
Use pursuant to applicable agreements
Safety statements Structure of safety statements
....................................................................................................................................................................................................................................
Signal words
The signal words identify the hazard severity levels asfollows:
Signal word
Meaning
DANGER
Indicates an extremely hazardous situation which, if not avoided,will
result in death or serious injury.
WARNING
Indicates a hazardous situation which, if not avoided, could resultin
death or serious injury.
CAUTION
Indicates a hazardous situation which, if not avoided, could resultin
minor or moderate injury.
NOTICE
Indicates a hazardous situation not related to personal injury.

....................................................................................................................................................................................................................................
1-4
Alcatel-Lucent –Proprietary
Use pursuant to applicable agreements
Safety statements
....................................................................................................................................................................................................................................
Safety
General precautions for installation procedures
WARNING
Failure to observe these safety precautions may result in personal
injury or damage to equipment.
 Read and understand all instructions.
 Follow all warnings and instructions marked on this product.
 Installation and maintenance procedures must be followed and performed by
trained personnel only.
 The equipment must be provided with a readily accessible disconnect device
as part of site preparation.
 Grounding and circuit continuity is vital for safe operation of the equipment.
Never operate the equipment with grounding/bonding conductor
disconnected.
 Before servicing, disconnect power input to reduce the risk of energy
hazards.
 If installed in ambient temperatures above 46°C (115°F), this unit mustbe
installed only in restricted access locations, where access is limited to
qualified service personnel only. The surface of the units can be very hot,
especially the top side of the RRH. The unit shall not be touched without
safety gloves and it shall be cooled down before touching.

Safety statements
Safety - specific hazards
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
1-5
Alcatel-Lucent –Proprietary
Use pursuant to applicable agreements
Safety - specific hazards
Danger
DANGER
Electric-shock hazard
Working in severe weather can result in personal injury or death and damage to the
equipment.
Never install or perform maintenance during severe weather (high winds, lightning,
blizzards, hurricane etc.).
DANGER
Noxious-substance hazard
Use of unspecified cleaning agents can result in personalinjury.
Use only specified cleaning agents. Never use flammablesolvents.
Always ensure there is adequate ventilation in the work area and wear the appropriate
personal protective equipment.
Warning
WARNING
Laser hazard
Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous laser radiation exposure.
Do not view directly into the laser beam with optical instruments such as a fiber
microscope because viewing of laser emission in excess of Class 1 limits significantly
increases the risk of eye damage.
Never look into the end of an exposed fiber or an open connector as long as the optical
source is switched on.
Ensure that the optical source is switched off before disconnecting optical fiber
connectors.

Safety statements
Safety - specific hazards
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
1-6
Alcatel-Lucent –Proprietary
Use pursuant to applicable agreements
WARNING
Fall hazard
Falls can occur when working at heights resulting in serious personal injury or death.
To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safe
work practices and wear appropriate fall protectionequipment.
Caution
CAUTION
RF hazard
RF exposure in excess of applicable limits can result in adverse health effects.
Metro Cells are designed and installed in order to comply with the international exposure
guidelines laid down by the International Commission on Non-Ionizing Radiation
Protection (ICNIRP) and/or the Institute of Electrical & Electronics Engineers
(IEEE) C95.1. ICNIRP guidelines have been implemented by the EuropeanCommission
and a number of other countries. IEEE guidelines have been used to develop the
regulations implemented in North America and some othercountries.
Workers that are required to work in close proximity to the equipment, for example
maintenance personnel, should strictly follow instructions provided by their employer.
Workers equipped with personal medical electronic devices, such as pacemakers and
hearing aids, shall consult the manufacturer's instructions and consult their occupational
health practitioner.
CAUTION
Electrical energy hazard
Some parts of all electrical installations are energized. Failure to observe this fact and
the safety warnings may lead to bodily injury and propertydamage.
For this reason, only trained and qualified personnel (electrical workers as defined in
IEC 60215 + A1 or EN 60215) may install or service theinstallation.

Safety statements
Safety - specific hazards
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
1-7
Alcatel-Lucent –Proprietary
Use pursuant to applicable agreements
CAUTION
Electrical energy hazard
The power supply lines to the network element are energized. Contact with parts carrying
voltage can cause health problems, possibly including death, even hours after theevent.
Open and lockout the load disconnect switch in the distribution box to completely
de-energize the network element.
Notices
NOTICE
Equipment damage hazard
Damaged connectors may lead to operational issues.
The Metro Cell must be transported by holding its body and not by any connectors or
pre-attached cables.
NOTICE
ESD hazard
Semiconductor devices can be damaged by electrostatic discharges(ESD)
The following rules must be complied with when handling any modulecontaining
semiconductor components:
 Wear conductive or antistatic working clothes (for example, coat made of 100%
cotton).
 Wear a grounded wrist strap.
 Wear shoes with conductive soles on a conductive floor surface or conductive work
mat.
 Leave the modules in their original packaging until ready for use.
 Make sure there is no difference in potential between yourself, the workplace, and the
packaging before removing, unpacking, or packing a module.
 Whenever handling ESD-sensitive components, do not touch any connection pins or
tracks.
 Place modules removed from the equipment on a conductive surface.
 Test or handle the module only with grounded tools on grounded equipment.
 Handle defective modules exactly like new ones to avoid causing further damage.

Safety statements
Safety - specific hazards
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
1-8
Alcatel-Lucent –Proprietary
Use pursuant to applicable agreements
NOTICE
Condensation
Sudden changes in the weather may lead to the formation of condensation on
components. Operating the unit when condensation moisture is present can destroy the
unit.
Units which show signs of condensation must be dried before installation.
NOTICE
Tools
Tools left in the working area can cause short circuits during operation which can leadto
the destruction of units.
Make sure after finishing your work that no tools, testing equipment, flashlights, etc.,
have been left in or on the equipment.

Safety statements
Safety - specific hazards
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
1-9
Alcatel-Lucent –Proprietary
Use pursuant to applicable agreements
....................................................................................................................................................................................................................................
Product safety
Equipment safety
Safety information for this equipment can be found on various Caution, Warning,Danger,
information labels or instructions affixed to or included with the product or included within this
document. Informational and cautionary labels may appear near the item they address or may be
grouped in a single location on the equipment. Warnings aretypically adjacent to the hazard that
is noted on the label. The instructions, cautions andwarnings found on these labels must be
understood and observed by all personnel involved with the equipment installation and
maintenance.