Alcatel-Lucent OAW-AP85 User manual

OAW-AP85 Field Replaceable Mount Kit
Installation Guide
0510359-01 | October 2007 1
Introduction
This installation guide covers the installation procedure for a field replaceable OAW-AP85 mount kit
only. This document does not include pre-installation and post-installation requirements, such as
minimum software requirements, AP provisioning, connecting power cables, and other network
requirements for an OAW-AP85 installation. Refer to the Alcatel-Lucent OAW-AP85 Outdoor Access
Point Series Installation Guide that shipped with your OAW-AP85 unit for complete details.
Package Checklist
zOAW-AP85 wall/pole/mast mount kit (fixture with hardware)
Mount Kit Replacement and OAW-AP85 Installation
!
CAUTION
Alcatel-Lucent Access Points are required to be installed by a professional installer. The
professional installer is responsible for ensuring that grounding is available and it meets applicable
local and national electrical codes.
WARNING
Do not work on an AP and do not connect or disconnect cables during periods of lightning activity.
!
CAUTION
Access Points are radio transmission devices and as such are subject to governmental regulation.
Network administrators responsible for the configuration and operation of Access Points must
comply with local broadcast regulations. Specifically, Access Points must use channel assignments
appropriate to the location in which the Access Point will be used.
!
CAUTION
RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits.
This equipment should be installed and operated with a minimum distance of 7.9 inches (20 cm)
between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter. When operated in the
5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the potential for
harmful interference with co-channel Mobile Satellite Systems.

2OAW-AP85 Field Replaceable Mount Kit | Installation Guide
Removing the Existing Mount Kit
1. Disconnect existing power and cable connections.
2. Remove the existing mount kit from the OAW-AP85.
Mounting the OAW-AP85
Preparing the OAW-AP85 for Installation
1. Install the four included mounting bolts (M8 bolts with captive flat washer) into the four mounting
holes on the rear of the OAW-AP85 (see Figure 1). Leave approximately two to three threads
showing on the mounting bolts.
Figure 1 Installing the Mounting Bolts
Wall Mounting the OAW-AP85
To wall mount an OAW-AP85:
1. Secure the mounting plate to a flat wall using the appropriate screws and anchors for your mounting
application (see Figure 2).
WARNING
Disconnect the AC mains before handling the AC power cable and connecting it to or disconnecting
it from the OAW-AP85.
Mounting Holes
Mounting Bolts
(M8 bolts, 4x)
NOTE
Wall mount hardware is not included with the mounting plate and must be purchased separately for
your mounting application. The mounting plate accepts the following screw/bolt sizes: M4, M5,
SAE #8, and SAE #10.

OAW-AP85 Field Replaceable Mount Kit | Installation Guide 3
Figure 2 Attaching the Mounting Plate
2. Seat the OAW-AP85 into the four keyholes on the mounting plate and tighten down the four
mounting bolts (M8 bolts) to secure the OAW-AP85 in place (see Figure 3). The mounting plate
should rest between the captive flat washer on each of the mounting bolts and the rear of the OAW-
AP85.
Figure 3 Wall Mounting the OAW-AP85
0128
Anchors (4x)
Mounting Plate
Screws (4x)
Wall
NOTE
The positioning of the keyholes on the mounting plate supports horizontal or vertical mounting of the
OAW-AP85, which is achieved by rotating the device by 90 degrees and securing it to the mounting
plate.
Mounting Bolts
Mounting Plate
OAW-AP85
Wall

4OAW-AP85 Field Replaceable Mount Kit | Installation Guide
Pole Mounting the OAW-AP85 (1.5” to 3.5” Diameter)
To mount an OAW-AP85 to a pole with a diameter of 1.5” to 3.5”:
1. Slide the long T-bolt through the opening in the mounting bracket (see Figure 4).
2. Attach the included retaining clip to the T-bolt (see Figure 4).
3. Screw the included nut onto the end of the T-bolt (see Figure 4).
4. Secure the mounting plate to the mounting bracket using the four included phillips head screws (see
Figure 4).
Figure 4 Assembling the Pole Mounting Bracket
5. Wrap the pole mounting bracket around a 1.5” to 3.5” diameter pole and secure the bracket in place
(see Figure 5).
a. Wrap the pole mounting bracket around the pole.
b. Slip the end of the T-bolt with nut through the opening in the pole mounting bracket.
c. Maneuver the T-bolt to the top slot in the pole mounting bracket and tighten down the nut.
Ensure that the nut is tightly secured and that the bracket cannot move. It must be secure to
support the weight of the OAW-AP85.
Figure 5 Securing the Pole Mounting Bracket
arun 0137
Nut (1x)
T-Bolt (1x)
Phillips Head Screws (4x)
Mounting Bracket
Mounting Plate
Retaining Clip
arun_0130
arun_0129
Step A Step B Step C

OAW-AP85 Field Replaceable Mount Kit | Installation Guide 5
6. Seat the OAW-AP85 into the four keyholes on the mounting plate and tighten down the four
mounting bolts (M8 bolts) to secure the OAW-AP85 in place (see Figure 6). The mounting plate
should rest between the captive flat washer on each of the mounting bolts and the rear of the OAW-
AP85.
Figure 6 Pole Mounting the OAW-AP85 (1.5” to 3.5” Diameter)
Figure 7 Horizontal Pole Mount Position (1.5” to 3.5” Diameter)
NOTE
The pole mounting bracket can be secured to a horizontal or vertical pole. The positioning of the
keyholes on the bracket supports horizontal or vertical mounting of the OAW-AP85 on either pole
type, which is achieved by rotating the device by 90 degrees and securing it to the bracket. Refer to
Figure 6 and Figure 7 for details.
Secured
Mounting Bracket
Tightened Mounting Bolts
OAW-AP85
Vertical Pole
arun_0131C
Secured
Mounting Bracket
Tightened Mounting
Bolts
OAW-AP85
Horizontal Pole

6OAW-AP85 Field Replaceable Mount Kit | Installation Guide
Pole Mounting the OAW-AP85 (>3.5” Diameter)
To mount an OAW-AP85 to a pole with a diameter greater than 3.5”:
1. Attach the mounting plate to the pole using outdoor rated straps (see Figure 8). Outdoor rated straps
are not included with the unit and must be purchased separately.
2. Seat the OAW-AP85 into the four keyholes on the mounting plate and tighten down the four
mounting bolts (M8 bolts) to secure the OAW-AP85 in place (see Figure 8). The mounting plate
should rest between the captive flat washer on each of the mounting bolts and the rear of the OAW-
AP85.
Figure 8 Pole Mounting the OAW-AP85 (>3.5” Diameter)
Positioning the OAW-AP85
To adjust the angle of an OAW-AP85 on a vertical pole:
1. Loosen the four M8 bolts on the side of the mounting plate and rotate the AP to the desired angle
and tighten down the M8 bolts (see Figure 9).
Figure 9 Positioning the OAW-AP85 on a Vertical Pole
NOTE
The mounting plate can be secured to a horizontal or vertical pole. The positioning of the keyholes
on the mounting plate supports horizontal or vertical mounting of the OAW-AP85 on either pole
type, which is achieved by rotating the device by 90 degrees and securing it to the mounting plate.
Outdoor Rated Straps
Mounting Plate
Mounting Bolts
OAW- Pole
M8 Positioning Bolts
(4x, 2x per side)

OAW-AP85 Field Replaceable Mount Kit | Installation Guide 7
To adjust the angle of an OAW-AP85 on a horizontal pole:
1. Rotate the entire mounting bracket to the desired angle and tighten the bracket into place (see
Figure 9).
Figure 10 Positioning the OAW-AP85 on a Horizontal Pole
Completing the Installation
Refer to the Alcatel-Lucent OAW-AP85 Outdoor Access Point Series Installation Guide that shipped
with your OAW-AP85 unit for complete installation details, such as connecting cables and power,
verifying connectivity, and configuration.
Safety and Regulatory Compliance
Alcatel-Lucent provides a multi-language document containing country specific restrictions and
additional safety and regulatory information for Alcatel-Lucent hardware products. The Alcatel-Lucent
Safety and Regulatory Addendum can be viewed or downloaded from the following location:
https://service.esd.alcatel-lucent.com.
arun_0131D
arun_0131E

8OAW-AP85 Field Replaceable Mount Kit | Installation Guide
Proper Disposal of Alcatel-Lucent Equipment
For the most current information on Global Environmental Compliance and Alcatel-Lucent products
please see our website at www.alcatel-lucent.com.
Waste of Electrical and Electronic Equipment
Alcatel-Lucent products at end of life are subject to separate collection and
treatment in the EU Member States, Norway, and Switzerland and therefore are
marked with the symbol shown at the left (crossed-out wheelie bin). The treatment
applied at end of life of these products in these countries shall comply with the
applicable national laws of countries implementing Directive 2002/96EC on Waste of
Electrical and Electronic Equipment (WEEE).
European Union RoHS
Alcatel-Lucent products also comply with the EU Restriction of Hazardous
Substances Directive 2002/95/EC (RoHS). EU RoHS restricts the use of specific
hazardous materials in the manufacture of electrical and electronic equipment.
Specifically, restricted materials under the RoHS Directive are Lead (including Solder used in printed
circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Alcatel-Lucent
products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in printed
circuit assemblies). Products and packaging will be marked with the “RoHS” label shown at the left
indicating conformance to this Directive.
China RoHS
Alcatel-Lucent products also comply with China environmental declaration requirements
and are labeled with the “EFUP e” label shown at the left.
Contacting Alcatel-Lucent
Web Site Support
Main Site http://www.alcatel-lucent.com/wps/portal/enterprise
Support Site https://service.esd.alcatel-lucent.com
Support Email [e-mail]
Telephone Support
North America 1-800-995-2696
Latin America 1-877-919-9526
Europe [phone]
Asia Pacific [phone]
Worldwide 1-818-880-3500