Alcatel-Lucent OmniAccess 700 User manual

Beta
1
2
Notes on numbered items on banner & legal pages
1u26801 West Agoura Road
Calabasas, CA 91301
[phone]
FAX [phone]
[email protected]
US Customer Support—[phone]
International Customer Support—[phone]
Internet—service.esd.alcatel-lucent.com
Website: www.alcatel-lucent.com
Part No: 060221-00, Rev. C
For final production, import color definitions from
\\daldoc01\docteam\templates\framemaker\book-template\color-defs\ production-colors.fm.
Do not import other template elements such as page layout.
To return to the draft version, import color def’ns from draft-colors.fm.
To switch to the beta version, import color def’ns from beta-colors.fm
OmniAccess 700
Getting Started Guide
Release Versions:
2.2
2.2-R02
2.3

CAUTION: THIS EQUIPMENT IS TO BE INSTALLED AND SERVICED ONLY BY QUALIFIED SERVICE
PERSONNEL.
Batteries Caution. There is a danger of explosion if the battery in your chassis is incorrectly replaced.
Replace the battery only with the same or equivalent type of battery recommended by the
manufacturer. Dispose of used batteries according to the manufacturer’s instructions. The
manufacturer’s instructions are as follows:
Copyright
The Specifications and Information regarding the products in this manual are subject to change without
notice. All statements, information, and recommendations in this manual are believed to be accurate
but are presented without warranty of any kind, express or implied. Users must take full responsibility
for their application of any products.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET
FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED
HEREIN BY THIS REFERENCE.
This equipment has been tested and found to comply within the limits pursuant to the (Centre for
Telecom) rules. These limits are designed to provide protection against harmful interference when the
equipment is operated in a commercial environment.
The following information is for the Users of the OmniAccess 700: If it is not installed in accordance with
the installation instructions, it may not function exactly to the said specifications. Modifying the
equipment without Alcatel-Lucent's written authorization may result in the equipment no longer
complying with the said dimensions.
Copyright © 2008, Alcatel-Lucent. All rights reserved.
Not withstanding any other warranty herein, all hardware and software are provided "as is" with all
faults. Alcatel-Lucent disclaim all warranties, expressed or implied, including, without limitation, those
of merchantability, fitness for a particular purpose and non-infringement or arising from a course of
dealing, usage, or trade practice. In no event shall Alcatel-Lucent be liable for any indirect, special,
consequential, or incidental damages, including, without limitation, lost profits or loss or damage to data
arising out of the use or inability to use this manual, even if Alcatel-Lucent have been advised of the
possibility of such damages.
Return the module with the battery to Alcatel-Lucent. The battery will be replaced at Alcatel-
Lucent’s factory.
3
4
5

Table of Contents
Package Contents.....................................................................................................................1
Required Tools and Equipment..........................................................................................2
Connecting AC Input Power......................................................................................................3
Connecting to the OA-700 Console Port...................................................................................5
Starting the OA-700 ..................................................................................................................8
Performing Basic Configuration Tasks....................................................................................12
Accessing the OA-700 Through CLI.................................................................................12
Accessing the OA-700 Through GUI................................................................................19
Cable Connection....................................................................................................................20
Obtaining Technical Support...................................................................................................20

List of Figures
Connecting the Power Cord on OA-740 3
Connecting the Power Cord on OA-780 4
Connecting to the OA-740 System Console 5
Connecting to the OA-780 System Console 6

List of Tables
Console Properties 7
OA-740 LED Status 8
OA-780 LED Status 9
Cable Connection 20

Package Contents
Except on the first page, right running head:
Heading1 or Heading1NewPage text (automatic)
1
Alcatel-Lucent
Beta Beta
OmniAccess 700 Getting Started Guide
PACKAGE CONTENTS
OA-740 Hardware
4-slot Chassis that includes
•Services Engine (SE) - 2-port 10/100/1000 Mbps Ethernet
•3 Fans (built-in)
•Power Supply (built-in)
Optional Modules Miscellaneous
•4-port T1E1 Line Card
•8-port 10/100/1000 Mbps Gigabit
Ethernet (GigE) Line Card
•4-port Universal Serial Port (USP) Line
Card (V.35/X.21/RS-232)
•AC Power Cord
•Console Cable
•Rack Mount Screws
•19-inch Rack Mount Ears
•512 MB USB Memory Flash
•Product Documentation CD
ROM
OA-780 Hardware
8-slot Chassis that includes
•Services Engine (SE) - 2-port 10/100/1000 Mbps Ethernet
•Switch Fabric (built-in)
•Fan Tray (built-in)
•Power Supply (built-in)
Optional Modules Miscellaneous
•Services Engine (second unit for
redundancy)
•Switch Fabric (second unit for
redundancy)
•Power Supply Tray (second unit for
redundancy or for load sharing)
•4-port T1E1 Line Card
•8-port 10/100/1000 Mbps Gigabit Ethernet
(GigE) Line Card
•4-port Universal Serial Port (USP) Line
Card (V.35/X.21/RS-232)
•AC Power Cord
•Console Cable
•Rack Mount Screws
•19-inch Rack Mount Ears
•512 MB USB Memory
Flash
•Product Documentation
CD ROM

Package Contents
Left running head:
Chapter name (automatic)
2Beta Beta
OmniAccess 700 Getting Started Guide
Alcatel-Lucent
REQUIRED TOOLS AND EQUIPMENT
You need the following items to install the OmniAccess 700 (OA-700):
•Electrostatic Discharge Wrist Strap (ESD)
•Level (optional)
•Tape Measure (optional)
Note: This equipment is designed to the highest quality standards of materials,
workmanship, and safety. Do not bypass any of the safety features of this equipment
or operate this in an improper environment.
Warning: Only trained and qualified personnel should be allowed to install or replace the
OA-700. Refer to the warnings and safety notes that are given in the “OmniAccess
740/780 Hardware Users Guide” provided with this device.
Refer to the “Rack Mounting the OA-740/OA-780” section in the “OmniAccess
740/780 Hardware Users Guide” to install the OA-700 in the rack.

Connecting AC Input Power
Except on the first page, right running head:
Heading1 or Heading1NewPage text (automatic)
3
Alcatel-Lucent
Beta Beta
OmniAccess 700 Getting Started Guide
CONNECTING AC INPUT POWER
This section provides the procedures for connecting AC-input power to the
OA-700.
Note: 1. The OA-700 installation must comply with all the applicable codes. All the
hardware materials used should be of compatible material and preclude
loosening, deterioration, and electro-chemical corrosion of hardware and
joined material.
2. OA-740 Power Supply Specification: The OA-740 requires 100/240V
and 6A (RMS) @115V, 3A (RMS) @230V AC power. A fully loaded OA-
740 consumes approximately 250W of power.
For more details on power supply specifications, see the “AC Power
Specifications” chapter in the “OmniAccess 740 Hardware Users
Guide”.
Figure 1: Connecting the Power Cord on OA-740

Connecting AC Input Power
Left running head:
Chapter name (automatic)
4Beta Beta
OmniAccess 700 Getting Started Guide
Alcatel-Lucent
3. OA-780 Power Supply Specification: The OA-780 requires 100/240V
and 6A (RMS) @115V, 3A (RMS) @ 230V AC power. A fully loaded OA-
780 consumes approximately 350W of power.
For more details on power supply specifications, see the “AC Power
Specifications” chapter in the “OmniAccess 780 Hardware Users
Guide”.
Figure 2: Connecting the Power Cord on OA-780
Step 1: Use the shipped power cord to power your system.
Step 2: Verify that the power switch located on the rear panel is in OFF (O)
position.
Step 3: Connect the system end of the connector to the OA-740/OA-780, as
shown in the figures above.
Step 4: Identify a power source point that complies with the system specifications,
and connect the power plug of the AC cable to the utility power socket.
Step 5: Ensure that the cable is not left in a hazardous position that could impair
movement of personnel or be frayed due to the movement of other equipment in
the vicinity.
Warning: Read the installation instructions before you connect the OA-700 to its power source.
OA7-PS-AC
Ready
Fault

Connecting to the OA-700 Console Port
Except on the first page, right running head:
Heading1 or Heading1NewPage text (automatic)
5
Alcatel-Lucent
Beta Beta
OmniAccess 700 Getting Started Guide
CONNECTING TO THE OA-700 CONSOLE PORT
The OA-700 has a RJ-45 console port connector. A RJ-45 - RJ-45 “roll-over”
cable along with RJ-45 to DB-9 (female) adapter is provided with the system to
access the console port via a DTE (computer/terminal). For additional connector
details, refer to “Pin Connector Details for OA-740/OA-780” in the
“OmniAccess 740/780 Hardware Users Guide”.
Figure 3: Connecting to the OA-740 System Console
OmniAccess
740
USB Modem
Console

Connecting to the OA-700 Console Port
Left running head:
Chapter name (automatic)
6Beta Beta
OmniAccess 700 Getting Started Guide
Alcatel-Lucent
Figure 4: Connecting to the OA-780 System Console
Note: Ensure that the OA-700 is powered off before connecting the console cable to the
system.
Port 0 Port 1

Connecting to the OA-700 Console Port
Except on the first page, right running head:
Heading1 or Heading1NewPage text (automatic)
7
Alcatel-Lucent
Beta Beta
OmniAccess 700 Getting Started Guide
To connect the OA-700 to the console, perform the following steps:
Step 1: Connect the RJ-45 end of the console cable to the front panel console
port on the OA-700 and the DB-9 end to the serial port (COM) on your computer/
terminal.
Step 2: Start your terminal emulation software.
Example: kermit or hyperterm terminal (if you are using Microsoft Windows
operating system) or minicom terminal (if you are using Unix/Linux operating
system).
Step 3: Set the console session as follows:
Table 1: Console Properties
Step 4: Watch for console message output or press the Enter key to get the
device prompt.
Parameter Value
Baud rate 9600
Parity None
Data Bits 8
Stop Bit 1
Flow control None

Starting the OA-700
Left running head:
Chapter name (automatic)
8Beta Beta
OmniAccess 700 Getting Started Guide
Alcatel-Lucent
STARTING THE OA-700
After installing your OA-700 and connecting cables, follow the procedure given
below to start the system:
Step 1: Before you power ON the OA-700, check the following:
•Ensure that the power supply tray is securely inserted into the chassis.
•Ensure that the utility power cable is connected to a valid power cord in the rear
panel, and power is available from this source.
•Ensure that the Switch Fabric and the SE modules are correctly and securely
installed.
•Ensure that a PC or VT100 terminal is connected to the console port, using the
appropriate console cable. (If the system is not connected to a console, see the
“Connecting to the OA-700 Console Port” section of this document to connect the
system to a console.)
Step 2: Power ON the OA-700.
Power on the OA-700 by turning on the external power switch located on the rear
panel. If power supply is available, you should hear the rotation of system fans,
and the system LEDs showing activity. At this point, the system begins its bootup
sequence.
Step 3: Monitor the system front panel LEDs and console for various bootup
messages.
Once the system begins to startup, monitor the front panel LEDs for various
stages of booting process (refer to the table given below). In addition to the LEDs,
monitor the system console for various bootup text messages (an example of a
bootup message is given below). While a console access is not always required
for system startup, it is a good idea to monitor the console at least the first time
the system is booted and initial configurations completed.
LED Information
The following table shows the state in which the main LEDs should be after a
startup.
Table 2: OA-740 LED Status
LED Status Description
SE EDs
Active Off Power up status. This is the default
display when the system is first
powered on and before the software is
loaded.
Green SE card is active.
Yellow Indicates transient conditions (e.g.,
booting).

Starting the OA-700
Except on the first page, right running head:
Heading1 or Heading1NewPage text (automatic)
9
Alcatel-Lucent
Beta Beta
OmniAccess 700 Getting Started Guide
Table 3: OA-780 LED Status
LED Status Description
SE LEDs
Active Off Power up status. This is the default display
when the system is first powered on and
before the software is loaded.
Green SE card is active.
Yellow Indicates transient conditions (e.g., booting).
Switch Fabric LEDs
Active Off Power up status. This is the default display
when the system is first powered on and
before the software is loaded.
Green Switch Fabric is active.
Fan Tray Status LED (Tricolor LED)
Off Power up status. This is the default display
when the system is first powered on and
before the software is loaded.
Red A component of the system is not managed
by the Chassis Manager, or the Chassis
Manager has exited, or the system was
“reloaded”, or the Chassis Manager has not
yet restarted.
Amber Indicates transient conditions (e.g., booting).
Green Bootup completed, and system is ready to
use.
Fan Tray LEDs (3 Uni-color Port LEDs) representing USB, Console, and Modem
ports
Off System is not working.
Console LED Green Console is accessible.

Starting the OA-700
Left running head:
Chapter name (automatic)
10 Beta Beta
OmniAccess 700 Getting Started Guide
Alcatel-Lucent
OA-740 Bootup Message
Example:
== Press ^C for Boot options ==
== Initiating startup sequence ==
Mounting internal storage medium...OK.
Checking storage medium...OK
##################################################
Alcatel-Lucent Software, Version 2.3.1.30
Copyright (c) 2003-2008 by Alcatel-Lucent Inc.
Built on Tue Dec 2 17:26:09 IST 2008
#################################################
Services Engine [3] Starting daughter processor
Services Engine [3] Installing image package
Services Engine [3] (SE) Installing image package
Loading Startup Config ...
/-------- Percent Complete --------
|*********************************
Services Engine [3] (SE) Initialization Complete
Username :superadmin
Password :
ALU>
OA-780 Bootup Message
Example:
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Red Hat certified release, version 2.27 - built 19:13:01,
Nov 20 2006
Copyright (C) 2000, 2001, 2002, Red Hat, Inc.
== Press ^C for Boot options ==
== Initiating startup sequence ==
Mounting internal storage medium...OK.
Checking storage medium...OK
##################################################
Alcatel-Lucent Software, Version 2.3.1.30
Copyright (c) 2003-2008 by Alcatel-Lucent Inc.
Built on Tue Dec 2 17:26:09 IST 2008
#################################################
Switch Card [24] Starting internal services
Switch Card [24] Installing image package
T1 Line Card [4] Installing image package
Services Engine [3] Starting daughter processor
L2 GiGe Card [5] Installing image package
Switch Card [24] Initialization complete
Services Engine [3] Installing image package
T1 Line Card [4] Initialization complete
L2 GiGe Card [5] Initialization complete

Starting the OA-700
Except on the first page, right running head:
Heading1 or Heading1NewPage text (automatic)
11
Alcatel-Lucent
Beta Beta
OmniAccess 700 Getting Started Guide
Services Engine [3] (SE) Installing image package
Loading Startup Config ...
/-------- Percent Complete --------
|*********************************
Services Engine [3] (SE) Initialization Complete
Username :superadmin
Password :
ALU>
Step 4: Configure the system.

Performing Basic Configuration Tasks
Left running head:
Chapter name (automatic)
12 Beta Beta
OmniAccess 700 Getting Started Guide
Alcatel-Lucent
PERFORMING BASIC CONFIGURATION TASKS
Once you boot the OA-700 and connect to the console, you can start configuring
your OA-700 either through the Command Line Interface (CLI) or the web-based
Graphical User Interface (GUI).
ACCESSING THE OA-700 THROUGH CLI
The CLI is the primary interface to access the OA-700 through the console. The
CLI allows you to configure, monitor, troubleshoot the system, and enables
network connectivity.
To perform initial configuration of your system, follow the procedure given below:
Step 1: Once the system bootup is complete, you are asked to configure the
password for a special user - superadmin. Superadmin is authorized to execute
any command. You need to set the superadmin password when the following
prompt is displayed:
Enter the new password for superadmin:
Once you enter the password for the superadmin, you will be asked to reconfirm
the password, with the following prompt:
Retype the new password:
After confirming the password, you will be asked to login using a user name. The
below prompt appears.
Username:
Enter the user name as superadmin. Now, you will be prompted for a password.
Password:
Enter the newly configured superadmin password.
Note: If you have any pre-existing user account, you can enter at the user name and
password prompts, else use the superadmin user account.
Step 2: After entering the correct user name and password, the ALU> prompt is
displayed. If the prompt is not seen, press the Enter key a few times.
ALU>
By default, the host name is “ALU”. (To configure a different host name, use the
configure “hostname <name>’ command in the Configuration mode.)
Step 3: At the ALU prompt, enter the enable command to enter the Super User
Mode (SUM).
Example:
ALU> enable
ALU#

Performing Basic Configuration Tasks
Except on the first page, right running head:
Heading1 or Heading1NewPage text (automatic)
13
Alcatel-Lucent
Beta Beta
OmniAccess 700 Getting Started Guide
Step 4: From SUM, you can enter the Configuration Mode (CM). The CM is used
to configure the system globally, to enter specific configuration modes, or to
configure specific elements, such as interfaces or protocols.
Enter the configure terminal command to enter the Configuration mode.
Example:
ALU# configure terminal
ALU(config)#
The above steps are to be followed to configure the OA-700 via the console.
Step 5: To configure the system remotely (Telnet, SSH, Modem), you need to
configure basic Authentication, Authorization, and Accounting (AAA)
configuration. AAA is a system in IP-based networking to control which users
have access to the system, what resources users have access to, and to keep
track of the activity of users over a network.
To enable the AAA services on your system, enter the aaa services command in
the Configuration mode.
Example:
ALU(config)# aaa services
Step 6: Set the enable password (system password). To set the system
password, enter the following command:
enable {secret|password} [5]<password>
Example:
ALU(config)# enable secret test
Secret for level 15 is set
Note: By default, only the console session is available without the enable password
configuration.
Step 7: Establish authentication for new users by configuring new user accounts.
To configure a new user account, use the following command:
username <user-name> {password [5]<password>|nopassword|
secret [5]<password>}
Example:
ALU(config)# username user1 password pass1

Performing Basic Configuration Tasks
Left running head:
Chapter name (automatic)
14 Beta Beta
OmniAccess 700 Getting Started Guide
Alcatel-Lucent
Step 8: Configuring an interface. Enter the following command to enter the
Interface Configuration mode:
interface <name> <slot/port>
Example:
ALU(config)# interface GigabitEthernet 7/0
ALU(config-interfaceGigabitEthernet7/0)#
(For more information on configuring interfaces, refer to the ‘The Command Line
Interface’ chapter in the OmniAccess 700 CLI Configuration Guide.)
Step 9: Administratively bring up the interface by using the ‘no shutdown’
command.
Example:
ALU(config-if GigabitEthernet7/0)# no shutdown
Step 10: Configure an IP address for the interface by entering the following
command. Enter the IP address in the valid IP address format A.B.C.D.
ip address {<ip-address subnet-mask>|<ip-address/prefix-
length>}
Example:
ALU(config-if GigabitEthernet7/0)# ip address 192.168.1.1/24
Note: In the above example, 192.168.1.1 is assumed to be the GigE 7/0 LAN facing
interface and IP address. You can configure the IP address based on your topology.
Step 11: Enable SSH and Telnet for in-band Management. The following
command enables SSH/Telnet connection to a remote computer:
•Secure Shell (ssh) is a program for logging in to a remote machine that provides
secure communication between two systems.
ssh {enable|disable}
Example:
ALU(config)# ssh enable
•Telnet is a user command and an underlying TCP/IP protocol for accessing
remote computers. Telnet is a program that enables connection to foreign or
remote host computers, and provides access to information on them.
telnet {enable|disable}
Example:
ALU(config)# telnet enable

Performing Basic Configuration Tasks
Except on the first page, right running head:
Heading1 or Heading1NewPage text (automatic)
15
Alcatel-Lucent
Beta Beta
OmniAccess 700 Getting Started Guide
Step 12: Enable HTTP & HTTPS for web-based management.
•HTTP is the primary protocol used to transfer files over the World Wide Web. You
can access the OA-700 using HTTP through a web browser after being
authenticated.
http {enable|disable}
Example:
ALU(config)# http enable
•HTTPS, in addition to the normal HTTP uses SSL encryption for secure
transmission of files.
Example:
ALU(config)# https enable
Note: SSH and HTTPS are not supported in the no crypto image. For information on the no
crypto release, refer to the release note.
Step 13: Enable Modem for Out of Band Management.
modem {enable|disable}
Example:
ALU(config)# modem enable
Step 14: Show Chassis - The ‘show chassis’ command provides a physical
inventory of the running chassis components for a specific slot or for the entire
system.
Example:
The following is an example of the show chassis command on an OmniAccess
740 system:
ALU> show chassis
Physical inventory at Thu Dec 11 08:48:30 2008
System started approximately Thu Dec 11 08:37:56 2008
Uptime is 0 days 0 hours 12 minutes 50 seconds
L2 - 8-port copper GigE (active)
Slot number: 1
Part number: 83000019
Manufacturer: ALU
Description: 8-port copper GigE
Serial number: DD0520001606
Version: 01
Revision: A00
LoL firmware version: 2.2.68
Loader version: 2.33
ALU-OS version: 2.3.1.30
MDCSerial number: WL0544000297
Revision: A00
Version: 01
SE - Services engine (active)
Slot number: 3