Alcatel-Lucent OmniAccess 5840 User manual

OA58XX-NW Router
Installation Manual
Copyright© ALU-DM632-I Version 1.1 September 2015 Alcatel-Lucent
Alcatel-Lucent Manual
OA58XX-NW Router 1

Legal Notice
Warranty
This publication is subject to change.
Alcatel-Lucent offers no warranty whatsoever for information contained in this manual.
Alcatel-Lucent is not liable for any direct, indirect, collateral, consequential or any other damage connected to the de-
livery, supply or use of this manual.
Manual Alcatel-Lucent
2OA58XX-NW Router

Table of Contents
Chapter1 AboutThisGuide.................................. 1
1.1 SupportedDevices................................... 1
1.2 Who should read this manual? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.3 When should this manual be read? . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.4 Whatisinthismanual?................................. 1
1.5 Whatisnotinthismanual? ............................... 1
1.6 How is the information organized? . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.7 TechnicalSupport ................................... 1
1.8 Relateddocumentation................................. 2
Chapter2 OA58XX-NWRouters ............................... 3
2.1 Characteristics..................................... 3
2.1.1 Powersupply ..................................... 3
2.1.2 HardwareMonitoring.................................. 3
Chapter 3 Components and Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.1 Components...................................... 4
3.1.1 FrontPanel...................................... 4
3.1.2 RearPanel ...................................... 6
3.1.3 TopPanel....................................... 7
3.1.4 SidePanel....................................... 7
3.2 ExpansionSlots.................................... 8
3.2.1 SLOT1-ExpansionSlot ................................ 8
3.2.2 SLOT2-ExpansionSlot ............................... 11
3.2.3 SLOT3–ExpansionSlot............................... 13
3.3 Installationinarack.................................. 16
3.4 PowerSource.................................... 16
3.4.1 InternalPowerSource................................. 17
3.4.2 PoESource..................................... 18
3.5 Microswitches.................................... 20
3.5.1 Procedure to ignore the configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.6 DataConnection................................... 22
3.6.1 8-portEthernetSwitch................................. 22
3.6.2 GE0/GE1Connections................................. 22
3.6.3 Connecting a USB 3G device (USB connector) . . . . . . . . . . . . . . . . . . . . . . 22
3.6.4 Connecting for Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Alcatel-Lucent Table of Contents
OA58XX-NW Router i

3.7 OptionalStorage................................... 23
3.7.1 Procedure to install a hard disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.7.2 Procedure to install a flash memory expansion USB . . . . . . . . . . . . . . . . . . . . 24
Appendix A Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
A.1 Troubleshooting................................... 26
A.2 Updatingthesoftware................................. 26
A.3 Connectingtothedevice ............................... 27
A.3.1 Connecting using the local console (Conf connector) . . . . . . . . . . . . . . . . . . . 27
A.4 Connectors ..................................... 27
A.4.1 LAN(GEx)Connector ................................ 28
A.4.2 WWANConnectors* ................................. 28
A.4.3 WLANConnectors*.................................. 28
A.4.4 ConfigurationConnector................................ 29
A.5 TechnicalSpecifications................................ 29
A.5.1 HardwareArchitecture................................. 29
A.5.2 LANInterfaces* ................................... 29
A.5.3 ConfigurationInterface ................................ 29
A.5.4 PowerSupply.................................... 30
A.5.5 Dimensionsandweight................................ 30
A.5.6 Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Appendix B Regulatory compliance and safety information . . . . . . . . . . . . . . . . . 31
B.1 Recycling and the Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
B.2 Translated Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
B.3 Compliance..................................... 34
B.3.1 FCCStatement.................................... 34
B.3.2 ICStatement..................................... 34
Table of Contents Alcatel-Lucent
ii OA58XX-NW Router

Chapter 1 About This Guide
This is the installation guide for the OA58XX-NW router and contains information on how to correctly install this
device in a working environment.
1.1 Supported Devices
The information provided in this installation guide only applies to the OA58XX-NW router family.
1.2 Who should read this manual?
This manual should be read by the support personnel who need to install, configure, maintain and monitor the
device.
1.3 When should this manual be read?
Read this guide as soon as you are ready to familiarize yourself with the device and its components.
This manual will help you understand your new device in greater depth.
1.4 What is in this manual?
This installation guide contains the following information:
• A description of the available features in the OA58XX-NW family.
• Technical specifications.
• Power supply requirements.
• A description of the device LEDs and connectors.
• Troubleshooting.
1.5 What is not in this manual?
This manual does not contain information relative to the device software or its configuration. For information on how
to configure this device, please see the relevant manuals, to be found on the ALU website:
http://enterprise.alcatel-lucent.com/UserGuides .
1.6 How is the information organized?
Each chapter focuses on a specific part of the hardware and its components. All descriptive, technical specifications
and information on a component can be found in the relevant chapter.
1.7 Technical Support
Alcatel-Lucent technical support is committed to resolving our customer’s technical issues in a timely manner. Cus-
tomers with inquiries should contact us at:
Contact information:
North America 800-995-2696
Latin America 877-919-9526
Alcatel-Lucent 1 About This Guide
OA58XX-NW Router 1

EMEA [phone] (Toll Free) or [phone]
Asia Pacific [phone]
Web: http://service.esd.alcatel-lucent.com
Email: esd.suppor[email protected]
1.8 Related documentation
ALU-Dm748-I Software Updating.
Note
The manufacturer reserves the right to make changes and improvements to either software or hard-
ware of this product, modifying the specifications of this manual without prior notice.
The images showing the front and back panels of the device are for information purposes only. Some
slight modifications may exist in the actual device.
1 About This Guide Alcatel-Lucent
2OA58XX-NW Router

Chapter 2 OA58XX-NW Routers
The OA58XX-NW router family consists of the following devices:
• OmniAccess 5840
OA5840 ESR modular chassis base model has 2 x GigE WAN, 8 x GigE LAN, 1x DSL slot, 1 x AIC slot. See part
number suffix for power cord plug type.
• OmniAccess 5850
OA5850 ESR modular chassis base model has 2 x GigE WAN, 8 x GigE LAN, 1x DSL slot, 2 x AIC slots. See SW
licenses available. See part number suffix for power cord plug type.
• OmniAccess 5850D
OA5850D ESR modular chassis with 250 GB HD memory storage for applications. See base model for ports. See
SW licenses available. See part number suffix for power cord plug type.
2.1 Characteristics
The OA58XX-NW routers are modular devices that combine router and switch functions in a single device. They
have been designed for a corporate environment, and include advanced security among their characteristics. The
OA58XX-NW routers incorporate encryption hardware.
The OA58XX-NW executes the ALU ESR-OS, which runs in all ALU router families and is characterized by a wide
variety of functionalities. It is especially designed to satisfy the access requirements to corporate data networks.
ESR-OS offers management capabilities, the possibility of implementing Quality of Service mechanisms (both at the
link layer and at the network layer) and security mechanisms, the potential to create Virtual Private Networks through
IPSec or L2TP, plus an extensive range of protocols and IP routing functionalities.
The OA58XX-NW router family can be expanded by means of a AIC card, allowing you to increase the range of in-
terfaces in the device.
This manual shows you how to install and connect these devices.
2.1.1 Power supply
For further information on the different OA58XX-NW power supplies, please see Power Source on page 16 inCom-
ponents and Power Supply on page 4.
2.1.2 Hardware Monitoring
The only way to monitor the OA58XX-NW router family hardware is through the LEDs on the front panel. These in-
dicate the state of the hardware components, if there is connectivity, data flow, etc.
For further information on the LED panel, please see Components on page 4 in the following chapter.
Alcatel-Lucent 2 OA58XX-NW Routers
OA58XX-NW Router 3

Chapter 3 Components and Power Supply
The following chapter provides detailed information on the chassis of the OA58XX-NW router family and its compon-
ents. This information includes:
• Components.
• Expansion modules.
• Information on assembly.
• Power supply.
• Micro-switches.
• Data connection.
3.1 Components
3.1.1 Front Panel
The following figure shows the front panel.
Fig. 1: Front Panel
The front panel elements are as follows:
Front panel elements table
Item Description
A Conf. RJ45 Connector, which provides access to the device’s local console for
configuration and monitoring purposes.
B USB: slot to connect a USB device.
C GE0/GE1: GigaEthernet Interfaces.
D PoE: connector for power supply through Ethernet (Power over Ethernet).
E 8-port switch Ethernet.
F SLOT 1: expansion slot for 8-port switch Ethernet expansion boards or AIC cards.
For further information, please see section SLOT 1 - Expansion Slot on page 8.
In addition to the connections, the front panel has several LEDs that provide information on the state of the router.
The following figure shows the front panel LEDs:
Fig. 2: Front panel LEDs
Below, you can find a description of each LED:
3 Components and Power Supply Alcatel-Lucent
4OA58XX-NW Router

Front panel LEDs table
LED Description State
On Power-on indicator. It lights up when connected to the
power.
USB Shows the state of the device con-
nected to the USB connector.
Off -> Device not connected, not de-
tected or incompatible.
Green -> Compatible device detec-
ted.
HD Indicates the activity of the internal
Hard Disk.
Off -> Hard disk is not connected or is
inactive.
Green -> If flashing, there is activity
on the hard disk.
3G Not supported Not supported
WiFi Not supported Not supported
SLOT Depends on the card installed in the
PCI slot.
Off -> Interface not available or not
installed (not supported).
Red -> Interface not found, no data
connection.
Yellow -> Connecting.
Green -> Communications estab-
lished.
xDSL Shows the status of the xDSL inter-
face.
Off -> Interface not available or not
installed (not supported).
Red -> Interface not found, no data
connection.
Yellow -> Connecting.
Green -> Communications estab-
lished.
In addition to the LEDs described in the above table, the front panel also has LEDs for the Gigabit and Switch Ether-
net interfaces.
Fig. 3: Gigabit Ethernet interface LEDs
The following table offers information on the LEDs associated to the Gigabit Ethernet interfaces:
Gigabit Ethernet interface LEDs table
LED Description State
Orange Ethernet connection speed Off -> Link has not been detected
Orange ->
Alcatel-Lucent 3 Components and Power Supply
OA58XX-NW Router 5

10 Mbps: Flashes once
100 Mbps: Flashes twice
1000 Mbps: Flashes three times
Green Ethernet (link) connection established Off -> Link has not been detected
Green -> Flashes depending on the
activity.
Fig. 4: Switch Ethernet interface LEDs
Below, you can find information on the LEDs associated to the Switch Ethernet interface:
Ethernet Switch interface LEDs table
LED Description Status
Orange Ethernet connection speed Off -> Link has not been detected
Orange -> 10 Mbps: Flashes depend-
ing on the activity.
Green Ethernet (link) connection established Off -> Link has not been detected
Green -> 100M bps: Flashes depend-
ing on the activity.
3.1.2 Rear Panel
The following figure shows the rear panel.
Fig. 5: Rear panel
The rear panel elements are as follows:
Rear panel connectors table
Item Description
A Not supported.
B SLOT 2: expansion slot for AIC cards. For further information, please see section
SLOT 2 - Expansion Slot on page 11.
C Not supported.
D SLOT 3: Expansion slot for xDSL cards. For further information, please see sec-
tion SLOT 3 – Expansion Slot on page 13.
E WWAN Main: main antenna for the OA58XX-NW cellular module. This module is
3 Components and Power Supply Alcatel-Lucent
6OA58XX-NW Router

optional, so your device may not have any antennas.
F Not supported.
G ON/OFF switch.
H Power cable connection.
3.1.3 Top Panel
The following figure shows the top panel.
Fig. 6: Top panel
The top panel elements are as follows:
Top panel elements table
Item Description
A Flap that provides access to the expansion cards.
3.1.4 Side Panel
The following figure shows the side panel.
Fig. 7: Side panel
The side panel elements are as follows:
Side panel elements table
Item Description
A Slots for the screws for rack mounting.
B Securing screws for the flap on the top panel.
C Securing screws for the top panel.
Alcatel-Lucent 3 Components and Power Supply
OA58XX-NW Router 7

3.2 Expansion Slots
The OA58XX-NW has three expansion slots (SLOT 1, SLOT 2 and SLOT 3) that allow you to expand features and
interfaces by inserting different cards or boards.
3.2.1 SLOT 1 - Expansion Slot
SLOT 1 is located on the right hand side of the device’s Front Panel on page 4. Here, you may insert an eight-port
Switch expansion card.
Fig. 8: SLOT 1 Expansion Slot
SLOT 1 elements table
Item Description
A Screws to hold the cover of the expansion module in SLOT 1.
B 8-port Switch Ethernet expansion module.
To correctly insert the card, please follow these steps:
(1) Switch off the device and remove the cables, as described in section Disconnecting on page 17.
(2) Remove the device from the workplace and place it in a stable, safe location where it can be easily accessed
and handled.
(3) Remove the screws from the side panel to be able to dismantle the flap that gives access to the expansion
cards.
Fig. 9: Remove the flap screws from the top panel
(4) Once the screws have been removed, slide the flap and lift it (making sure no grooves attach the flap to the top
panel). Place it in a safe location.
Fig. 10: Top panel without flap
(5) Find the place where the expansion board needs to be located. Look for the lateral connector of the card con-
3 Components and Power Supply Alcatel-Lucent
8OA58XX-NW Router

nection and the card standoff posts to the chassis.
Fig. 11: Location of the lateral connector for SLOT 1 expansion module
(6) Using a screwdriver, remove the cover covering the expansion slot. This cover is located on the front panel.
Fig. 12: Remove the cover from SLOT 1
(7) Insert the expansion board and connect it. This operation must be carried out carefully, without forcing any
piece or part of the device.
(8) Screw in the board. Firmly tighten the screws without damaging the board.
(9) Put the cover back on the expansion slot and screw it down.
Fig. 13: Replace the cover on SLOT 1
(10) Reposition the top panel flap and screw it into place using the screws.
Fig. 14: Replace the screws on the top panel flap
(11) Connect and switch on the device, as explained in section Connecting on page 17. Should you encounter any
problems, switch off the device and make sure that the above steps have been carried out correctly. If the prob-
lem persists, please contact your supplier.
(12) Connect a terminal to the console and check that the device detects the expansion board.
**************************************************
**************************************************
**************************************************
BIOS CODE DUMP....................
BIOS DATA DUMP.....
End of BIOS dump
FLASH BIOS CODE VERSION: 02.01 Mar 6 2013 17:59:56 L1
Alcatel-Lucent 3 Components and Power Supply
OA58XX-NW Router 9

Current date: Mar 27 2013, Wednesday Current time: 12:56:57
System Info:
PCB:0x128 GPPORCR:0x00280000 PVR:0x80212051 SVR:0x80EC0011
CLKs(KHz): CCB=393216 CPU0=786432 CPU1=786432 DDR(clk)=327680 LBUS=49152
Watchdog: Enabled
MMU Mode: Dynamic
ICache: ON; DCache: ON Write-Back; L2Cache: ON
Mem Info:
DRAM size: 512 Megabytes
BANK 0: 512 Megabytes (detected)
FLASH: 65024 KB.
NVRAM: 128 KB.
EEPROM: 2048 Bytes.
Devices:
GIGABIT ETHERNET 1
GIGABIT ETHERNET 2
LAN OVER SWITCH
SWITCH(16) 10/100 CARD 0x18
POE CARD 1
SECURITY ENGINE
Slot 1 - PCI device: PowerPC processor, Host
(Bus: 10, Device: 0, Function: 0)
(Vendor: 0x1957, Device: 0x0100)
(Subs. Vendor: 0x0000, Subs. Device: 0x0000)
Slot 1 - PCI device: PCI-to-PCI bridge
(Bus: 11, Device: 0, Function: 0)
(Vendor: 0x10B5, Device: 0x8112)
(Subs. Vendor: 0x0000, Subs. Device: 0x0000)
Slot 1 - PCI device: bridge
(Bus: 12, Device: 14, Function: 0)
(Vendor: 0x1057, Device: 0x18C1)
(Subs. Vendor: 0x5444, Subs. Device: 0x1700)
Current production date: 11 23
Current software license: 28 60
S/N: 754/00111
BIOS MAC Add: 00-a0-26-a2-00-2c
>>.....
....
TRYING APP DUMP
(CONFIGURED) appcode1.bin ver.: 0.11.0.1 0.0.0.0
APP0 CODE DUMP. Mode:0.....................................
APP0 DATA DUMP.............................................
APP CODE DUMP..............................................
APP DATA DUMP..............................................
Running application at: 0x00200140
Flash configuration read
Parsing text mode configuration ...
Configuration parsed
Initializing
Press any key to get started
3 Components and Power Supply Alcatel-Lucent
10 OA58XX-NW Router

3.2.2 SLOT 2 - Expansion Slot
SLOT 2 is located on the left hand side of the device’s Rear Panel on page 6. In this case, we insert a AIC (Add-in
card) into the SLOT.
Fig. 15: SLOT 2 Expansion Slot
SLOT 2 elements table
Item Description.
A Screws to hold the cover of the expansion module in SLOT 2.
B AICexpansion module.
To correctly insert the card, please follow these steps:
(1) Switch off the device and remove the cables, as described in section Disconnecting on page 17.
(2) Remove the device from the workplace and place it in a stable, safe location where it can be easily accessed
and handled.
(3) Remove the screws from the side panel to be able to dismantle the flap that gives access to the expansion
cards. Please see Fig. 9 on page 8.
(4) Once the screws have been removed, slide the flap and lift it (making sure no grooves attach the flap to the top
panel). Place it in a safe location.
(5) Find the place where the expansion board needs to be located. This slot has a set of elevated connectors with
gold contacts and a pair of standoffs.
Fig. 16: AIC Expansion board: Location
(6) Using a screwdriver, remove the expansion slot cover. This cover is located on the rear panel. Push this out.
Fig. 17: Removing the SLOT 2 cover
(7) Place AIC board standoff posts over the securing screws. Secure these firmly.
(8) Place the AIC card in the slot so that this firstly adjusts to the space on the device rear panel and subsequently
to the two AIC connections. This operation must be carried out carefully, without forcing any piece or part of the
device. Check that the board is clearly settled over the AIC connectors. Please see Fig. 18 on page 12.
Alcatel-Lucent 3 Components and Power Supply
OA58XX-NW Router 11

Fig. 18: Inserting the AIC expansion card
(9) Screw the AIC board to the standoff posts using two screws and their corresponding washers. Firmly tighten the
screws without damaging the board.
Fig. 19: Screwing down the AIC expansion card
(10) Reposition the expansion slot cover and screw it down
Fig. 20: Reposition the SLOT 2 cover
(11) Replace the top panel flap and screw it into place using the screws. Please see Fig. 14 on page 9.
(12) Connect and switch on the device, as explained in section Connecting on page 17. Should you detect any prob-
lems, switch off the device and make sure that the above steps have been carried out correctly. If the problem
persists, please contact your supplier.
(13) Connect a terminal to the console and check that the device detects the AIC board:
**************************************************
**************************************************
**************************************************
BIOS CODE DUMP....................
BIOS DATA DUMP.....
End of BIOS dump
FLASH BIOS CODE VERSION: 02.01 Mar 6 2013 17:59:56 L1
Current date: Mar 27 2013, Wednesday Current time: 12:56:57
System Info:
PCB:0x128 GPPORCR:0x00280000 PVR:0x80212051 SVR:0x80EC0011
CLKs(KHz): CCB=393216 CPU0=786432 CPU1=786432 DDR(clk)=327680 LBUS=49152
Watchdog: Enabled
MMU Mode: Dynamic
ICache: ON; DCache: ON Write-Back; L2Cache: ON
Mem Info:
DRAM size: 512 Megabytes
BANK 0: 512 Megabytes (detected)
FLASH: 65024 KB.
NVRAM: 128 KB.
EEPROM: 2048 Bytes.
Devices:
3 Components and Power Supply Alcatel-Lucent
12 OA58XX-NW Router

GIGABIT ETHERNET 1
GIGABIT ETHERNET 2
LAN OVER SWITCH
SWITCH(8) 10/100 CARD 0x18
POE CARD 1
SECURITY ENGINE
Slot 1 - PCI device: PowerPC processor, Host
(Bus: 10, Device: 0, Function: 0)
(Vendor: 0x1957, Device: 0x0100)
(Subs. Vendor: 0x0000, Subs. Device: 0x0000)
Slot 1 - PCI device: PCI-to-PCI bridge
(Bus: 11, Device: 0, Function: 0)
(Vendor: 0x10B5, Device: 0x8112)
(Subs. Vendor: 0x0000, Subs. Device: 0x0000)
Slot 1 - PCI device: bridge
(Bus: 12, Device: 14, Function: 0)
(Vendor: 0x1057, Device: 0x18C1)
(Subs. Vendor: 0x5444, Subs. Device: 0x1700)
Current production date: 11 23
Current software license: 28 60
S/N: 754/00111
BIOS MAC Add: 00-a0-26-a2-00-2c
>>
.....
....
TRYING APP DUMP
(CONFIGURED) appcode1.bin ver.: 0.11.0.1 0.0.0.0
APP0 CODE DUMP. Mode: 0....................................
APP0 DATA DUMP.............................................
APP CODE DUMP..............................................
APP DATA DUMP..............................................
Running application at: 0x00200140
Flash configuration read
Parsing text mode configuration ...
Configuration parsed
Initializing
Press any key to get started
3.2.3 SLOT 3 – Expansion Slot
SLOT 3 is located in the middle of the device’s rear panel (see Rear Panel on page 6). Insert an xDSL expansion
board in this SLOT.
Fig. 21: xDSL expansion card module
SLOT 3 elements table
Item Description.
A Screws to hold the cover of the expansion module in SLOT 3.
B xDSL expansion module.
Alcatel-Lucent 3 Components and Power Supply
OA58XX-NW Router 13

To correctly insert the card, please follow these steps:
(1) Switch off the device and remove the cables, as described in section Disconnecting on page 17.
(2) Remove the device from the workplace and place it in a stable, safe location where it can be easily accessed
and handled.
(3) Remove the screws from the side panel to be able to dismantle the flap that gives access to the expansion
cards. Please see Fig. 9 on page 8.
(4) Once the screws have been removed, slide the flap and lift it (making sure no grooves attach the flap to the top
panel). Place it in a safe location.
(5) Find the place where the xDSL expansion board needs to be located.
Fig. 22: xDSL expansion board: Location
(6) Remove the lid that holds the back cover located on the rear panel.
Fig. 23: Lid cover for xDSL
(7) Using a screwdriver, remove the expansion slot cover.
Fig. 24: Removing the SLOT 3 cover
(8) Place the xDSL expansion card so that this firstly adjusts to the space on the device rear panel and sub-
sequently to the motherboard connection. This operation must be carried out carefully, without forcing any piece
or part of the device. Check that the board is clearly settled over the motherboard connector.
(9) Screw the board to the securing posts using two screws and their corresponding washers. Firmly tighten the
screws without damaging the board.
(10) Put the expansion slot cover back and screw it down.
Fig. 25: Repositioning the SLOT 3 cover
(11) Rearrange the top panel flap and screw it into place using the screws. Please see Fig. 14 on page 9.
(12) Connect and switch on the device as explained in section Connecting on page 17. Should you detect any prob-
lems, switch off the device and make sure that the above steps have been carried out correctly. If the problem
persists, please contact your supplier.
(13) Connect a terminal to the console and check that the device detects the xDSL board.
3 Components and Power Supply Alcatel-Lucent
14 OA58XX-NW Router

**************************************************
**************************************************
**************************************************
BIOS CODE DUMP....................
BIOS DATA DUMP.....
End of BIOS dump
BIOS menu address: 0x4BD78
FLASH BIOS CODE VERSION: 02.01 Mar 6 2013 17:59:56 L1
Current date: Mar 27 2013, Wednesday Current time: 12:56:57
System Info:
PCB:0x128 GPPORCR:0x00280000 PVR:0x80212051 SVR:0x80EC0011
CLKs(KHz): CCB=393216 CPU0=786432 CPU1=786432 DDR(clk)=327680 LBUS=49152
Watchdog: Enabled
MMU Mode: Dynamic
ICache: ON; DCache: ON Write-Back; L2Cache: ON
Mem Info:
DRAM size: 512 Megabytes
BANK 0: 512 Megabytes (detected)
FLASH: 65024 KB.
NVRAM: 128 KB.
EEPROM: 2048 Bytes.
Devices:
GIGABIT ETHERNET 1
GIGABIT ETHERNET 2
ADSL CARD 0x08
LAN OVER SWITCH
SWITCH(8) 10/100 CARD 0x18
POE CARD 1
SECURITY ENGINE
Slot 1 - PCI device: PowerPC processor, Host (Bus: 10, Device: 0, Function: 0)
(Vendor: 0x1957, Device: 0x0100)
(Subs. Vendor: 0x0000, Subs. Device: 0x0000)
Slot 1 - PCI device: PCI-to-PCI bridge
(Bus: 11, Device: 0, Function: 0)
(Vendor: 0x10B5, Device: 0x8112)
(Subs. Vendor: 0x0000, Subs. Device: 0x0000)
Slot 1 - PCI device: bridge
(Bus: 12, Device: 14, Function: 0)
(Vendor: 0x1057, Device: 0x18C1)
(Subs. Vendor: 0x5444, Subs. Device: 0x1700)
Current production date: 11 23
Current software license: 28 60
S/N: 754/00111
BIOS MAC Add: 00-a0-26-a2-00-2c
>>
.....
....
TRYING APP DUMP
(CONFIGURED) appcode1.bin ver.: 0.11.0.1 0.0.0.0
APP0 CODE DUMP. Mode: 0....................................
APP0 DATA DUMP.............................................
APP CODE DUMP..............................................
APP DATA DUMP..............................................
Alcatel-Lucent 3 Components and Power Supply
OA58XX-NW Router 15

Running application at: 0x00200140
Flash configuration read
Parsing text mode configuration ...
Configuration parsed
Initializing
Press any key to get started
3.3 Installation in a rack
The OA58XX-NW can be installed in a 19” rack. To do this, you need two plastic brackets like the ones shown be-
low. The brackets and screws are not included in the basic packet and have to be acquired separately.
Both brackets are attached to the device by means of 8 screws (4 on each side), as shown.
Fig. 26: Attaching the brackets
The spaces for the screws in the OA58XX-NW router leave the factory protected by covers. These can be removed
with a sharp tool (such as a small flat screwdriver). We recommend removing the upper cover to simplify the pro-
cess.
Fig. 27: Device with the brackets
3.4 Power Source
The OA58XX-NW router is powered with an internal power source.
Additionally, the OA58XX-NW router can hold an optional card to inject PoE through the 8-port Switch. In this case,
the device is served from an AC/DC external power source to power the PoE module.
3 Components and Power Supply Alcatel-Lucent
16 OA58XX-NW Router