Alcatel-Lucent Service Aggregation Router 7705 User manual

Alcatel-Lucent 7705
SERVICE AGGREGATION ROUTER | RELEASE 1.0
16-PORT T1/E1 ASAP ADAPTER CARD INSTALLATION GUIDE
Alcatel-Lucent Proprietary
This document contains proprietary information of Alcatel-Lucent and is not to be disclosed
or used except in accordance with applicable agreements.
Copyright 2008 © Alcatel-Lucent. All rights reserved.

When printed by Alcatel-Lucent, this document is printed on recycled paper.
Alcatel-Lucent assumes no responsibility for the accuracy of the information presented, which is
subject to change without notice.
Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All
other trademarks are the property of their respective owners.
Copyright 2008 Alcatel-Lucent.
All rights reserved.
Disclaimers
Alcatel-Lucent products are intended for commercial uses. Without the appropriate network design
engineering, they must not be sold, licensed or otherwise distributed for use in any hazardous
environments requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft
navigation or communication systems, air traffic control, direct life-support machines, or weapons
systems, in which the failure of products could lead directly to death, personal injury, or severe physical
or environmental damage. The customer hereby agrees that the use, sale, license or other distribution
of the products for any such application without the prior written consent of Alcatel-Lucent, shall be at
the customer's sole risk. The customer hereby agrees to defend and hold Alcatel-Lucent harmless from
any claims for loss, cost, damage, expense or liability that may arise out of or in connection with the
use, sale, license or other distribution of the products in such applications.
This document may contain information regarding the use and installation of non-Alcatel-Lucent
products. Please note that this information is provided as a courtesy to assist you. While Alcatel-Lucent
tries to ensure that this informationaccuratelyreflects informationprovided by the supplier, please refer
to the materials provided with any non-Alcatel-Lucent product and contact the supplier for
confirmation. Alcatel-Lucent assumes no responsibility or liability for incorrect or incomplete
information provided about non-Alcatel-Lucent products.
However, this does not constitute a representation or warranty. The warranties provided for
Alcatel-Lucent products, if any, are set forth in contractual documentation entered into by
Alcatel-Lucent and its customers.
This document was originally written in English. If there is any conflict or inconsistency between the
English version and any other version of a document, the English version shall prevail.

16-port T1/E1 ASAP Adapter Card Installation Guide Page 3
Table of Contents
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installing Adapter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Provisioning Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Component Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Provisioning an Adapter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Configuration Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Warnings and Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Installing an Adapter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Removing and Replacing an Adapter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Connector and LED Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
16-port T1/E1 ASAP Adapter Card Connectors and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
T1/E1 Cable Pinout Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
68-pin AMP to 68-pin AMP T1/E1 Cable — Pinout Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
68-pin AMP to Open-ended Wire T1/E1 Cable — Pinout Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Table of Contents
Page 4 16-port T1/E1 ASAP Adapter Card Installation Guide

16-port T1/E1 ASAP Adapter Card Installation Guide Page 5
List of Tables
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Table 1: Information Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing Adapter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Table 2: Component Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Table 3: Adapter Card Installation Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Connector and LED Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Table 4: 16-port T1/E1 ASAP Adapter Card Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
T1/E1 Cable Pinout Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Table 5: 68-pin AMP to 68-pin AMP T1/E1 Cable Pinout Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 6: 68-pin AMP to Open-ended Wire T1/E1 Cable Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 7: 68-pin AMP to Open-ended Wire Pinout Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

List of Tables
Page 6 16-port T1/E1 ASAP Adapter Card Installation Guide

16-port T1/E1 ASAP Adapter Card Installation Guide Page 7
List of Figures
Installing Adapter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 1: 7705 SAR-8 Slot Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 2: Installing an Adapter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 3: Removing an Adapter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Connector and LED Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 4: 16-port T1/E1 ASAP Adapter Card Connectors and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
T1/E1 Cable Pinout Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 5: 68-pin AMP to 68-pin AMP Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 6: 68-pin AMP to Open-ended Wire T1/E1 Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

List of Figures
Page 8 16-port T1/E1 ASAP Adapter Card Installation Guide

16-port T1/E1 ASAP Adapter Card Installation Guide Page 9
Preface
About This Guide
This guide provides site preparation recommendations and step-by-step procedures to
install, remove, and replace the Alcatel-Lucent 16-port T1/E1 Any Service Any Port
(ASAP) Adapter card.
The 16-port T1/E1 ASAP Adapter card supports channelization down to DS0. Each port
supports TDM, Inverse Multiplexing over ATM (IMA), and multilink bundles over PPP
channels (MLPPP). A single 68-pin AMP connector on the faceplate provides access and
network connection for all ports.
After the hardware installation process is completed, refer to the List of Technical
Publications for details on the boot process, software configuration, and Command Line
Interface (CLI) information to configure system and network parameters.
List of Technical Publications
The 7705 SAR OS documentation set is composed of the following guides:
• 7705 SAR OS Basic System Configuration Guide
This guide describes basic system configurations and operations.
• 7705 SAR OS System Management Guide
This guide describes system security and access configurations as well as event
logging and accounting logs.
• 7705 SAR OS Interface Configuration Guide
This guide describes card and port provisioning.
Warning:
• All plugs must be properly crimped and conform to FCC Code of Regulations (CFR) Part
68, Subpart F. Failure to comply will result in damage to the jack.

Preface
Page 10 16-port T1/E1 ASAP Adapter Card Installation Guide
• 7705 SAR OS Router Configuration Guide
This guide describes logical IP routing interfaces, IP-based filtering, and routing
policies.
• 7705 SAR OS MPLS Guide
This guide describes how to configure Multiprotocol Label Switching (MPLS) and
Label Distribution Protocol (LDP).
• 7705 SAR OS Services Guide
This guide describes how to configure service parameters such as service access
points (SAPs), service destination points (SDPs), customer information, user
services, and Operations, Administration and Management (OAM) tools.
• 7705 SAR OS Quality of Service Guide
This guide describes how to configure Quality of Service (QoS) policy
management.
Warnings and Notes
Observe the warnings and notes to avoid injury or router damage during installation and
maintenance. Follow the safety procedures and guidelines when working with and near
electrical equipment. Warning statements and notes are provided in each chapter.
Audience
This guide is intended for network installers and system administrators who are responsible
for installing, configuring, or maintaining networks. This guide assumes you are familiar
with electronic and networking technologies.

Preface
16-port T1/E1 ASAP Adapter Card Installation Guide Page 11
Information Symbols
Table 1 describes symbols contained in this guide.
Technical Support
If you purchased a service agreement for your 7705 SAR and related products from a
distributor or authorized reseller, contact the technical support staff for that distributor or
reseller for assistance. If you purchased an Alcatel-Lucent service agreement, contact your
welcome center at:
Web: http://www1.alcatel-lucent.com/comps/pages/carrier_support.jhtml
Table 1: Information Symbols
Symbol Meaning Description
Danger This symbol warns that improper handling and installation could result in bodily
injury. Before you begin work on this equipment, be aware of hazards involving
electrical circuitry, be aware of your networking environments, and instigate
accident prevention procedures.
Warning This symbol warns that improper handling and installation could result in
equipment damage or loss of data.
Caution This symbol warns that improper handling may reduce your component or
system performance.
Note This symbol provides additional operational information.
Class 1 laser products are listed in the Class 1 laser adapter card documents.
Only approved Class 1 replaceable laser transceivers should be used with those
products.
Class 1 Laser Product

Preface
Page 12 16-port T1/E1 ASAP Adapter Card Installation Guide

16-port T1/E1 ASAP Adapter Card Installation Guide Page 13
Installing Adapter Cards
In This Chapter
This chapter provides information about installing and removing the adapter cards in the
7705 SAR-8 chassis:
•Provisioning Requirements on page 14
•Component Power Consumption on page 15
•Provisioning an Adapter Card on page 16
→Configuration Example on page 16
•Installation Procedures on page 18
→Warnings and Notes on page 18
→Installing an Adapter Card on page 19
→Removing and Replacing an Adapter Card on page 20

Provisioning Requirements
Page 14 16-port T1/E1 ASAP Adapter Card Installation Guide
Provisioning Requirements
To configure cards and ports, you must be able to access the 7705 SAR-8 by console or
Telnet connection. Refer to the 7705 SAR-8 Installation Guide for information and
instructions on console and Telnet connections.
The CSM does not require provisioning. However, the IOM, which is an integral part of the
CSM software module, must be activated before any adapter cards and port parameters can
be provisioned and configured. The IOM is activated using the card and card-type CLI
commands to specify its slot number and card type. Adapter cards must be provisioned
before their ports can be configured.
Configure components in the following order:
1. Card slot number (use the card command)
2. Card type
3. Adapter card slot number (use the mda command)
4. Adapter card type
5. Ports
Note:
• IOMs are specified using the card and card-type commands (items 1 and 2 in the list
below).
• Adapter cards are provisioned and configured using the mda and mda-type commands
(items 3 and 4 in the list below).

Installing Adapter Cards
16-port T1/E1 ASAP Adapter Card Installation Guide Page 15
Component Power Consumption
Table 2 lists the power consumption for the chassis, CSM, and 16-port T1/E1 ASAP
Adapter card.
Refer to the 7705 SAR-8 Installation Guide for more information on the power consumption
of other components.
Table 2: Component Power Consumption
Component Conservative Estimate (Watts)
SAR-8 chassis
(unpopulated, all fans operating)
28 W
CSM 17 W
16-port T1/E1 ASAP Adapter card 17 W

Provisioning an Adapter Card
Page 16 16-port T1/E1 ASAP Adapter Card Installation Guide
Provisioning an Adapter Card
After the IOM has been activated on the CSM (Steps 1 and 2 below), continue in the
config context with the following CLI commands to provision the adapter card. The steps
below provision 16-port T1/E1 ASAP Adapter cards in slots MDA 5 and 6. In Release 1.0, a
maximum of six 16-port T1/E1 ASAP Adapter cards can be configured on a 7705 SAR-8.
Command Syntax Example
Step 1. card slot-number card 1
Step 2. card-type card-type card-type iom-1g
Note: In Release 1.0, the slot-number is always 1 and the card-type is always iom-
1g.
Step 3. mda mda-number mda 5
Step 4. mda-type mda-type mda-type a16-chds1
Step 5. exit exit
To configure an additional adapter card, continue the configuration process with Step 6:
Step 6. mda mda-number mda 6
Step 7. mda-type mda-type mda-type a16-chds1
Step 8. exit exit
Configuration Example
The following example displays the card, card-type, mda and mda-type commands to
specify the IOM as an iom-1g type, and provision 16-port T1/E1 ASAP Adapter cards in
slots MDA 5 and 6.
ALU-1>config# card 1
ALU-1>config>card# card-type iom-1g
ALU-1>configcard# mda 5
ALU-1>config>card>mda# mda-type a16-chds1
ALU-1>config>card>mda# exit
ALU-1>config>card# mda 6
ALU-1>config>card>mda# mda-type a16-chds1
ALU-1>config>card>mda# exit
Sample Output
Use the config>info command to display card configuration information:
ALU-1>config# info

Installing Adapter Cards
16-port T1/E1 ASAP Adapter Card Installation Guide Page 17
. . .
----------------------------------------------
echo "Card Configuration"
#---------------------------------------------
card 1
card-type iom-1g
mda 5
mda-type a16-chds1
exit
mda 6
mda-type a16-chds1
exit
exit
----------------------------------------------
ALU-1>config#
Use the config>show card state command to display administrative and operational
states for all cards:
ALU-1>config# show card state
===============================================================================
Card State
===============================================================================
Slot/ Provisioned Equipped Admin Operational Num Num Comments
Id Type Type State State Ports MDA
-------------------------------------------------------------------------------
1 iom-1g iom-1g up up 6
1/5 a16-chds1 a16-chds1 up up 16
1/6 a16-chds1 down provisioned 16
A csm-1g csm-1g up up Active
B csm-1g up down Standby
===============================================================================
ALU-1>config#
Use the config>show mda command to display provisioned adapter card information:
ALU-1>config# show mda
===============================================================================
MDA Summary
===============================================================================
Slot Mda Provisioned Equipped Admin Operational
Mda-type Mda-type State State
-------------------------------------------------------------------------------
1 5 a16-chds1 a16-chds1 up up
6 a16-chds1 down provisioned
===============================================================================
ALU-1>config#

Installation Procedures
Page 18 16-port T1/E1 ASAP Adapter Card Installation Guide
Installation Procedures
Warnings and Notes
Warning:
• Electrostatic discharge (ESD) damage can occur if adapter cards are mishandled. Always
wear an ESD-preventive wrist or ankle strap connected to a nearby ground point that is
connected to the site grounding point (typically, the grounding stud on the 7705 SAR-8, or
a properly grounded rack or work bench).
• Always place components on a flat anti-static surface.
• For first-time power up during chassis installation, do not power up a 7705 SAR-8 until all
components are installed and verified as having been installed correctly.
• Slot covers are required in all empty slots to prevent excess dust accumulation and to help
control airflow and electromagnetic interference.
• To comply with the GR-1089-CORE requirement R4-9 [31] standard for electromagnetic
compatibility and safety, all intra-building ports are specified for use with shielded and
grounded cables at both ends.
• The intra-building port(s) of the equipment or sub-assembly is suitable for connection to
intra-building or unexposed wiring or cabling only. The intra-building port(s) of the
equipment or sub-assembly must not be metallically connected to interfaces that connect to
the Outside Plant (OSP) or its wiring. These interfaces are designed for use as intra-
building interfaces only (Type 2 or Type 4 ports as described in GR-1089-CORE) and
require isolation from the exposed OSP cabling. The addition of primary protectors is not
sufficient protection in order to connect these interfaces metallically to OSP wiring.
Notes:
• Ports cannot be configured until the adapter card is provisioned.
• Services cannot be configured until the ports are configured.
• Adapter card slot numbers are MDA 1 through MDA 6.
• T1/DS1 terminations support 100-ohm impedance; E1 terminations support 75-ohm and
120-ohm termination impedances.

Installing Adapter Cards
16-port T1/E1 ASAP Adapter Card Installation Guide Page 19
Installing an Adapter Card
A maximum of six 16-port T1/E1 ASAP Adapter cards can be installed on the 7705 SAR-8
in MDA slots 1 through 6. Figure 1 identifies the location of the MDA slots. Figure 2
illustrates the installation of an adapter card. Ejector levers help install and remove the
adapter card; captive screws secure the card in place.
The 16-port T1/E1 ASAP Adapter card has one 68-pin AMP connector on its faceplate for
high-density, direct connections, or for connection to a distribution panel available from
Alcatel-Lucent. Refer to the 7705 SAR-8 Installation Guide for more information on
distribution panels.
Figure 1: 7705 SAR-8 Slot Identification
Figure 2: Installing an Adapter Card
CSM A
MDA 1
MDA 3
MDA 5
CSM B
MDA 2 FAN Batt B
MDA 4
MDA 6
Batt A
1963
5
A16-CND31
Stat
Pwr
Act
Ports 1-16
Port
Minor
Major
Critical
Batt B
Batt A
Fan Alarm
External
Alarms
FAN
7705 SAR-8
CSM A
SLOT ID
MDA 1
MDA 3
MDA 5
CSM B
MDA 2
MDA 4
MDA 6
43
3
2
1
4
1964
3

Installation Procedures
Page 20 16-port T1/E1 ASAP Adapter Card Installation Guide
Refer to Connector and LED Descriptions on page 23 for information on the connectors and
LEDs on the 16-port T1/E1 ASAP Adapter card. Refer to T1/E1 Cable Pinout Assignments
on page 27 for cable descriptions and pinout assignments.
If the MDA slot for the adapter card has not been provisioned or configured before installing
the card, refer to Provisioning an Adapter Card on page 16.
Tools required:
• torque driver for Phillips screws
To install an adapter card:
Step 1. Remove the adapter card from the packaging and place on a flat anti-static work
surface. Avoid touching the board components and connector pins.
Step 2. With the ejector levers rotated inward, hold the adapter card by the levers, align the
card with the slot guides, and slide the adapter card into the slot (see Figure 2).
Step 3. Press the adapter card firmly into the slot. Make sure that the card connectors are
seated in the backplane connectors.
Step 4. Tighten the captive screws to secure the card. Do not over-tighten. The recommended
torque is 4-6 lbf.-in.
Step 5. Check the Power LED. If the adapter card is properly inserted and power to the
7705 SAR-8 has been applied, the Power LED is lit blue. See Connector and LED
Descriptions on page 23 for a description of LED activity.
Removing and Replacing an Adapter Card
If you replace an adapter card with a different type, you must change the configuration to
reflect the new adapter card type prior to removing the installed card. Each active port must
be shut down before you shut down and remove an adapter card configuration (see Changing
an Adapter Card Configuration on page 21). If you replace an adapter card with the same
Table 3: Adapter Card Installation Features
Key Description
1 Slot guide
2 Threaded receptacle
3 Captive screw
4 Ejector lever