Alcoa AK Series User manual

08-22-2005
HK1057
AK-175 & 180 Series Tooling
INSTRUCTION MANUAL
AK-175
SERIES PNEUDRAULIC RIVETING TOOLS

AK-175 & 180 Series Tooling Alcoa Fastening Systems
3
SAFETY
This instruction manual must be read with particular
attention to the following safety guide lines, by any
person servicing or operating this tool.
1. Safety Glossary
WARNINGS - Must be understood
to avoid severe personal injury.
CAUTIONS - show conditions that will dam-
age equipment and or structure.
Notes - are reminders of required proce-
dures.
Bold, Italic type and underlining - empha-
sizes a specific instruction.
2. Huck equipment must be maintained in a safe
working condition at all times and inspected on a
regular basis for damage or wear. Any repair
should be done by a qualified repairman trained
on Huck procedures.
3. Repairman and Operator must read manual prior
to using equipment and understand any Warning
and Caution stickers/labels supplied with equip-
ment before connecting equipment to any pri-
mary power supply. As applicable, each of the
sections in this manual have specific safety and
other information.
4. See MSDS Specifications before servicing the
tool. MSDS Specifications are available from
your Huck representative or on-line at
www.huck.com. Click on Installation Systems
Division.
5. When repairing or operating Huck installation
equipment, always wear approved eye protec-
tion. Where applicable, refer to ANSI Z87.1 -
1989
6. Disconnect primary power source before doing
maintenance on Huck equipment.
7. If any equipment shows signs of damage, wear,
or leakage, do not connect it to the primary
power supply.
8. Make sure proper power source is used at all
times.
9. Never remove any safety guards or pintail
deflector.
10. Never install a fastener in free air. Personal
injury from fastener ejecting may occur.
11. Do not abuse tool by dropping or using it as a
hammer. Never use hydraulic or air lines as a
handle. Reasonable care of installation tools by
operators is an important factor in maintaining
tool efficiency, eliminating downtime, and in pre-
venting an accident which may cause severe
personal injury.
12. Never place hands between nose assembly and
work piece.
!
Product complies with requirements
set forth by the relevant European
directives.
Read manual prior to using
equipment.
Eye protection required while
using this equipment.
Hearing protection required while
using this equipment.

4
AK-175 & 180 Series Tooling Alcoa Fastening Systems
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
PRINCIPLE OF OPERATION AND TOOL SPECIFICATIONS . . . . . . . . . . . . .5
OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
RIVET PINTAIL REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
THREE PIECE JAW INSTALLATION AND REMOVAL . . . . . . . . . . . . . .7 & 8
TOOL MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
OPTIONAL ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
90 DAY WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
AUTHORIZED TOOL SERVICE CENTERS . . . . . . . . . . . . . . . . . . . . . . . . .12
CONTENTS

5
AK-175 & 180 Series Tooling Alcoa Fastening Systems
SEE PG. 5
(3 PC.)-202929
(2 PC.)-202122
TOOL BODY
Figure 1
NOSE PIECE
201061
NOSE TUBE
JAW PUSHER
PULLER SHA T
APPROX. 3/4 GAP AT
FULL EXTENSION
JAWS
201050
JAW HOLDER
202124
RETURN SPRING
202312
RESERVIOR SHIELD
ACTUATING TRIGGER "A"
RELEASING TRIGGER "B"
PRINCIPLE OF OPERATION AND TOOL SPECIFICATIONS
READ INSTRUCTIONS THOROUGHLYPRIOR TO
OPERATING THE RIVETER. THIS RIVETER IS
DESIGNED FOR INTERMITTENT DUTY AND MAINTE-
NANCE WORK ONLY.
The AK-175 is a pneudraulic tool designed to set from 1/8"
up to and including 1/4 inch diameter steel, stainless steel,
aluminum and plastic rivets by changing only the nosepiece.
The AK-175 has a rated pull pressure of over 3,500 lbs. The
AK-175 riveter will operate effectively at any air pressure
between 90 and 120 psi. WHEN SETTING 1/4" RIVETS OR
MAGNALOK®A MINIMUM AIR PRESSURE OF 110 p.s.i.
MUST BE MAINTAINED The maximum air pressure used
with the tool should not exceed 120 psi.
The AK-175 utilizes totally different patented principles than
any other riveter. The air pressure activates a reciprocating
hydraulic pump which generates the force required to set
the fastener.
The hydraulic system is sealed and, although there may be
some visible residue around the trigger area, oil need not be
added. If the AK-175 should become damaged and leaks oil
from the tool, IT SHOULD BE RETURNED TO AN AUTHO-
RIZED SERVICE CENTER. (Authorized Service Centers
may be found in Tool Serivce Center Section of the Manual)
Model Weight Min PSI Max PSI Rivet Diameter Pull Pressure Stroke
AK-175 32 oz 90* 120 1/8”-1/4” 3500 lbs. 5/8”
*When setting 1/4” MAGNALOK®rivets, MIN Air pressure is 110 psi
Accessories
* Nose Extension Kit
P/N 205490
For more accessories see the
optional accessories section

6
AK-175 & 180 Series Tooling Alcoa Fastening Systems
OPERATING INSTRUCTIONS
Nose Piece Installation:
To change the Nose Piece
1. Remove the NOSE PIECE in the tool
by unscrewing it in a counterclockwise direction.
2. Actuate tool until it is fully extended. (There
should be gap of approximately 3/4" in between
the RESERVOIR SHIELD and the tool body.(see fig. 1)
3. Hand tighten the NOSE PIECE into the NOSE TUBE
and release the tool by squeezing the releasing trigger “B”
only.
Fastener Installation:
Install correct nose piece on tool (see NOSE PIECE
installation section).
1. Insert pintail of rivet in to the nose piece.
2. Then Position the rivet body in to work piece
to be fastened.
3. Hold the tool steady against the work piece
and squeeze ACTUATING TRIGGER “A”
only, until fastener is installed and rivet pin-
tail is broken* (see fig. 2 below)
RELEASING TRIGGER "B"
ACTUATING TRIGGER "A"
Figure 2
WORK PIECE
RIVET BODY
RIVET PINTAIL
(INSIDE NOSE PIECE)
NOTICE:
Before operating tool, make sure that all NOSE PARTS have been screwed in HAND
TIGHT.
Frequently check that nose components do not vibrate loose during operation
The AK-175 pneudraulic riveter installs fasteners by a pull and release system. Squeezing the
ACTUATING TRIGGER "A" only (Fig. 2) will actuate the tool. The tool must be actuated when installing fasteners
and changing nose pieces. After installing the fastener or changing the NOSE PIECE the tool must be returned to
its original position, this releases the pintail if a fastener was installed. To do this point the tool downward and
squeeze RELEASING TRIGGER "B" only (Fig. 3). See sections on NOSE PIECE INSTALLATION and FASTENER
INSTALLATION for detailed instructions.
*The AK-175 has a 5/8 inch work travel and will set most rivets in one cycle. If the tool reaches the end of its travel before the rivet
breaks, the hydraulic system will lug down. DO NOT continue lugging the tool. Release the tool by squeezing the RELEASING TRIG-
GER "B", regrip the rivet, squeeze the ACTUATING TRIGGER "A" and finish the installation.
SELECT THE PROPER NOSE PIECE FOR THE CORRECT INSTALLATION OF FASTENER AND FUNCTION OF TOOL.
(Typical Rivet)
BODY
PINTAIL

7
AK-175 & 180 Series Tooling Alcoa Fastening Systems
1.
2.
2.
Figure 3
TWO PIECE JAW SYSTEM THREE PIECE JAW SYSTEM
Remove the JAW HOLDER by unscrewing it in a
counterclockwise direction. Drop JAWS out from SPRING side.
Actuate tool by squeezing the ACTUATING TRIGGER (see fig
3 above) until the jaw pusher is fully extended. Stop as soon as
the JAW PUSHER is in the extended position.
PULLER
SHA T
JAW
PUSHER
Remove the JAW HOLDER by unscrewing it in a
counterclockwise direction. Drop JAWS out from
SPRING side. Push JAW PUSHER flush with PULLER
SHA T while squeezing the RELEASING TRIGGER
(See igure 3 above).
PULLER
SHA T
JAW
PUSHER
RELEASING
TRIGGER "B"
RIVET PINTAIL
ACTUATING
TRIGGER "A"
Once Rivet is installed pintail must be removed
1. Point tool downward
2. Squeeze RELEASING TRIGGER “B”.
It is necessary to REMOVE PINTAIL
BEFORE ATTEMPTING TO INSTALL
ANOTHER RIVET (see fig 3).
PINTAIL REMOVAL AND THREE PIECE JAW INSTALLATION AND REMOVAL
Rivet Pintail Removal:
The jaws are installed at the factory and should only need to be removed for periodic inspection and
cleaning. To remove the jaws unscrew the NOSE TUBE from the tool in a counterclockwise direction
Three/Two Piece Jaw Installation and Removal:

8
AK-175 & 180 Series Tooling Alcoa Fastening Systems
TWO PIECE JAW SYSTEM
TWO JAW SYSTEM
THREE PIECE JAW SYSTEM
3. 3.
4.
5.
6.
THREE JAW SYSTEM
5.
When jaws are in place, insert jaw holder into spring, being sure to keep large end of jaw holder pointing downward.
Replace the NOSE TUBE and NOSE PIECE, HAND TIGHTEN ONLY. The tool is now ready to use.
SPRING
JAW HOLDER
To replace JAWS, hold JAW HOLDER large end down and at a
slight angle. Place jaws in one at a time. Add a small amount of
jaw lubricant to jaws and jaw holder prior to assembly.
Hold tool with the PULLER SHA T pointing down and screw the
jaw holder on to the PULLER SHA T. HAND TIGHTEN ONLY.
To replace JAWS, hold JAW HOLDER large end down and at a slight
angle. Hold finger over small opening and place jaws in one at a time.
Add a small amount of jaw lubricant to jaws and jaw holder prior to
assembly.
Hold tool with the PULLER SHA T pointing down and the JAW
PUSHER fully extended. Screw the jaw holder on to the PULLER
SHA T. HAND TIGHTEN ONLY.
TOOL
BODY
PULLER
SHA T
TOOL
BODY
PULLER
SHA T
JAW
PUSHER

9
AK-175 & 180 Series Tooling Alcoa Fastening Systems
*
Ø.093
Ø.098
Ø.093
Ø.130
Ø.125 Ø.172
Ø.160
Ø.160
Ø.160
Ø.160
Part No. Description
1/4" Magna Lok
Spec. GM Glass Stop
Travel, Pop Rivets
1/4" Monobolts
1/4" Pop & Plastic
Rivets
1/4" Auto Split "T"
Rivets
3/16" Monobolts
5/32" & 3/16" Pop
& Plastic Rivets
1/8" Stand Off
Pop Rivets
'3/32" & 1/8"
Pop Rivets
1/8" for Trim Molding
Pop Rivets
202142
202193
202169
202157
202155
202168
202158
202190
202159
202156
Nose Pieces * Included in AK-175 kit
*
*
*
Part No. Description
Steps for Proper Tool Maintenance and Operation
1. Disassemble and clean NOSE components periodically
or if the pintails do not drop out freely, use a pick to clean
the jaw grooves. Wash components in mineral spirits or
isopropyl alcohol. Apply a small amount of light weight oil
to the JAWS and inside of JAW HOLDER prior to assem-
bly.
2. To ease NOSE TUBE and NOSE PIECE installation,
extend tool by squeezing actuating trigger.
3. DO NOT USE TOOL AS A LEVER if rivet pin tail is
jammed while re-gripping. Instead, with releasing trigger
depressed, push tool nose against work piece for the
jaws to get a deeper grip
4. If rivet pintail is stuck in tool after breaking, lightly tap
nose against a hard surface while squeezing the releas-
ing trigger, pintail should then fall out.
5. Before operating tool, make sure that all NOSE PARTS
have been screwed in HAND TIGHT.
6. For long life of tool, do not continue to run tool at the end
of travel.
7. The AK-175 should not be used at temperatures below
35° F. unless it is first brought to room temperature and
cycled several times, normal use of the tool after warm-
ing should keep it warm enough for proper operation.
8. If tool will not reverse, remove NOSE TUBE and inspect
for any foreign matter that might have caused jamming
between JAW HOLDER and inside of NOSE TUBE.
9. Frequently check that nose components do not vibrate
loose during operation.

10
AK-175 & 180 Series Tooling Alcoa Fastening Systems
TROUBLESHOOTING
Problem Solution
1.) Rivet Pintail is stuck in tool First Step:
Lightly tap nose against a hard surface while
after breaking squeezing HANDLES and pressing
down the RELEASING BUTTON with tool pointing
downward Pintail should then fall out, see fig. 4.
(If that does not work try Second Step.)
Second Step: (Use this only if first step does not work)
Remove NOSE TUBE and JAW HOLDER (for help
see figure 5) take out pintail and reassemble.
2.) Tool will not reverse Push on the handles until you feel a slight give,
then press the RELEASING BUTTON and continue pushing on
the handles, the tool should then reverse. If this does not work
Remove NOSE TUBE and inspect for any foreign matter that may
have cause the jamming between JAW HOLDER and the inside
of NOSE TUBE.
3.) Fastener does not pull rivet The JAW HOLDER is loose. Remove the NOSE TUBE and tight-
en the JAW HOLDER by turning it counter clockwise (See Three
Piece Jaw Installation and Removal.)
4.) The Rivet does not Fit into the Tool The rivet is to large, or the wrong NOSE PIECE is on the tool. To
find the correct NOSE PIECE (see chart on page 11). If you do
not have the needed NOSE PIECE, See next page for how to
order the correct one.
5.) Premature Breaking See solution for problem 4. Also verify the grip of the fastener
and make sure you are not rocking the tool during installation.
6.) Jamming of Tool See solution for problem 4. Also verify that you have the proper
jaw engagement and that all parts are hand tight and that the
jaws are cleaned and properly assembled in jaw pusher (See
Three Piece Jaw Installation and Removal)
7.) Rivet not installed properly See solution for problem 4. Also verify that appropriate fastener is
being used and proper fastener grip length for the application has
been selected
8.) Jaws Breaking See solution for problem 4. Check to see all parts are properly
assembled and hand tight.
9.) Damaged Jaw Pusher See solution for problem 4. Check to see if all parts are properly
assembled.

11
AK-175 & 180 Series Tooling Alcoa Fastening Systems
OPTIONAL ACCESSORIES
Part Number Description
202156 Nose Piece - 1/8” for Trim Molding Pop Rivets
202159 Nose Piece - 3/32” & 1/8” Pop Rivets
202190 Nose Piece - 1/8” Stand Off Pop Rivets
202158 Nose Piece - 5/32” & 3/16” Pop and Plastic Rivets
202168 Nose Piece - 3/16” Monobolts
202155 Nose Piece - 1/4” Auto Split “T” Rivets
202157 Nose Piece - 1/4” Pop and Plastic Rivets
202169 Nose Piece - 1/4” Monobolts
202193 Nose Piece - Spec. GM Glass Stop Travel, Pop Rivets
202142 Nose Piece - 1/4” Magna Lok
205490 Nose Extension Kit
126016 Rivet Stem Removal Tool- “Punch Assembly”
202122 Two Piece Jaws
202929 Three Piece JAws
To order an item please call your closest dealer.

12
AK-175 & 180 Series Tooling Alcoa Fastening Systems
90 Day Warranty on AK-175 Riveter
U.S. Patent No's 4248077, 4263801, 4735048
All Alcoa Fastening Systems tools and parts have been carefully tested and checked at the factory and are guar-
anteed to be free from defects in material and workmanship, subject to the following conditions.
A.) The tools manufactured by Alcoa Fastening Systems will be repaired free of charge or replaced at our dis-
cretion within 90 days of sale to the first user if, upon examination at our service center, we find a defect in
material or workmanship in the hydraulic system.
B.) The tool must be returned intact and prepaid to one of our service centers. Proof of date of sale must accom-
pany any tool returned. This warranty will be void if repairs have been made or attempted by others, or if the
tool has been subject to abuse, neglect, accident or improper application.
C.) The foregoing obligation is Huck's sole liability under this or any implied warranty, and no one is authorized
to vary its terms or conditions.
D.) If you have any problems please contact Customer Service at the factory: [phone].
Before returning tools to the service center, please use the operation and main-
tenance tips on page 9 of this manual. If the tool continues to malfunction call
the Customer Technical Support at Alcoa Fastening Systems [phone]
for additional assistance.
Authorized Tool Service Centers:
Central Fastening Systems
801 McCann Road
Rogers, AR 72758
479 936 7577
888 370 1894 (Toll Free)
479 636 2119 (Fax)
Professional Tool Center
2236 S.116th Street
West Allis, WI 53227
414 321 1234
414 321 2524 (Fax)
FSI
1206 East Mac Arthur St
Sonoma, CA 95476
707 935 1170
800 344 2394 (Toll Free)
707 935 1828 (Fax)
Universal Repair Shop
1611 Boylston Avenue
Seattle, WA 98122
206 322 2726
206 322 2126 (Fax)
J.O. King
1265 Alpharetta Road
Alpharetta, GA 30201
770 751 1875
800 241 2681 (Toll Free)
770 442 0950 (Fax)

AK-175 & 180 Series Tooling Alcoa Fastening Systems
LIMITED WARRANTIES
Tooling Warranty: Huck warrants that tooling and other
items (excluding fasteners, and hereinafter referred as
"other items") manufactured by Huck shall be free from
defects in workmanship and materials for a period of nine-
ty (90) days from the date of original purchase.
Warranty on "non standard or custom manufactured
products": With regard to non-standard products or cus-
tom manufactured products to customer's specifications,
Huck warrants for a period of ninety (90) days from the
date of purchase that such products shall meet Buyer's
specifications, be free of defects in workmanship and
materials. Such warranty shall not be effective with
respect to non-standard or custom products manufactured
using buyer-supplied molds, material, tooling and fixtures
that are not in good condition or repair and suitable for
their intended purpose.
THERE ARE NO WARRANTIES WHICH EXTEND
BEYOND THE DESCRIPTION ON THE FACE HEREOF.
HUCK MAKES NO OTHER WARRANTIES AND
EXPRESSLY DISCLAIMS ANY OTHER WARRANTIES,
INCLUDING IMPLIED WARRANTIES AS TO MER-
CHANTABILITY OR AS TO THE FITNESS OF THE
TOOLING, OTHER ITEMS, NONSTANDARD OR CUS-
TOM MANUFACTURED PRODUCTS FOR ANY PARTIC-
ULAR PURPOSE AND HUCK SHALL NOT BE LIABLE
FOR ANY LOSS OR DAMAGE, DIRECTLY OR INDI-
RECTLY, ARISING FROM THE USE OF SUCH TOOL-
ING, OTHER ITEMS, NONSTANDARD OR CUSTOM
MANUFACTURED PRODUCTS OR BREACH OF WAR-
RANTY OR FOR ANY CLAIM FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
Huck's sole liability and Buyer's exclusive remedy for any
breach of warranty shall be limited, at Huck's option, to
replacement or repair, at FOB Huck's plant, of Huck man-
ufactured tooling, other items, nonstandard or custom
products found to be defective in specifications, workman-
ship and materials not otherwise the direct or indirect
cause of Buyer supplied molds, material, tooling or fix-
tures. Buyer shall give Huck written notice of claims for
defects within the ninety (90) day warranty period for tool-
ing, other items, nonstandard or custom products
described above and Huck shall inspect products for which
such claim is made.
Tooling, Part(s) and Other Items not manufactured by
Huck.
HUCK MAKES NO WARRANTY WITH RESPECT TO
THE TOOLING, PART(S) OR OTHER ITEMS MANUFAC-
TURED BY THIRD PARTIES. HUCK EXPRESSLY DIS-
CLAIMS ANY WARRANTY EXPRESSED OR IMPLIED,
AS TO THE CONDITION, DESIGN, OPERATION, MER-
CHANTABILITY OR FITNESS FOR USE OF ANY TOOL,
PART(S), OR OTHER ITEMS THEREOF NOT MANU-
FACTURED BY HUCK. HUCK SHALL NOT BE LIABLE
FOR ANY LOSS OR DAMAGE, DIRECTLY OR INDI-
RECTLY, ARISING FROM THE USE OF SUCH TOOL-
ING, PART(S) OR OTHER ITEMS OR BREACH OF
WARRANTY OR FOR ANY CLAIM FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES.
The only warranties made with respect to such tool, part(s)
or other items thereof are those made by the manufactur-
er thereof and Huck agrees to cooperate with Buyer in
enforcing such warranties when such action is necessary.
Huck shall not be liable for any loss or damage resulting
from delays or nonfulfillment of orders owing to strikes,
fires, accidents, transportation companies or for any rea-
son or reasons beyond the control of the Huck or its sup-
pliers.
Huck Installation Equipment
Huck International, Inc. reserves the right to make
changes in specifications and design and to discontinue
models without notice.
Huck Installation Equipment should be serviced by trained
service technicians only.
Always give the Serial Number of the equipment when cor-
responding or ordering service parts.
Complete repair facilities are maintained by Huck
International, Inc.
Authorized Tool Service Centers (ATSC's) offer repair
services, spare parts and Nose inserts and accessories.
Please contact your Huck Representative or the nearest
Huck office listed on the back cover for the ATSC in your
area.

Americas
Alcoa Fastening Systems
Aerospace Products
Tucson Operations
3724 East Columbia
Tucson, AZ 85714
800-234-4825
520-747-9898
FAX: [phone]
Alcoa Fastening Systems
Aerospace Products
Carson Operations
PO Box 5268
900 Watson Center Rd.
Carson, CA 90749
800-421-1459
310-830-8200
FAX: [phone]
Alcoa Fastening Systems
Commercial Products
Waco Operations
PO Box 8117
8001 Imperial Drive
Waco, TX 76714-8117
800-388-4825
254-776-2000
FAX: [phone]
Alcoa Fastening Systems
Commercial Products
Kingston Operations
1 Corporate Drive
Kingston, NY 12401
800-278-4825
845-331-7300
FAX: [phone]
www.hucktools.com
Alcoa Fastening Systems
Commercial Products
Canada Operations
6150 Kennedy Road, Unit 10
Mississagua, Ontario L5T2J4
Canada
905-564-4825
FAX: [phone]
Alcoa Fastening Systems
Commercial Products
Latin America Operations
Avenida Parque Lira. 79-402
Tacubaya Mexico, D.F.
C.P. 11850
FAX: [phone]
TELEX: 1173530 LUKSME
Far East
Alcoa Fastening Systems
Commercial Products
Australia Operations
14 Viewtech Place
Rowville, Victoria
Australia 3178
03-764-5500
Toll Free: 008-335-030
FAX: [phone]
Europe
Alcoa Fastening Systems
Commercial Products
United Kingdom Operations
Unit C, Stafford Park 7
Telford, Shropshire
England TF3 3BQ
01952-290011
FAX: [phone]
Alcoa Fastening Systems
Aerospace Products
France Operations
15 Rue Du Petit ALBI
95807 Cencgy-Pontoise
France
33-1-34-33-9782
FAX: [phone]
ISO 14000
Certified
For the Long Haul™
A Global Organization
Alcoa Fastening Systems (AFS) maintains company
offices throughout the United States and Canada,
with subsidiary offices in many other countries.
Authorized AFS distributors are also located in
many of the world’s
industrial and Aerspace centers, where they provide
a ready source of AFS fasteners, installation tools,
tool parts, and application assistance.
For The Long Haul,The Future of Fastening Technology,
The Future of Assembly Technology, The Future of Tooling
Technology, and Tools of Productivity are service marks of Huck
International. Huck provides technical assistance regarding the use
and application of Huck fasteners and tooling.
NOTICE:The information contained in this publication is only for
general guidance with regard to properties of the products shown
and/or the means for selecting such products, and is not intended
to create any warranty, express, implied, or statutory; all warranties
are contained only in Huck’s written quotations, acknowledge-
ments, and/or purchase orders. It is recommended that the user
secure specific, up-to-date data and information regarding each
application and/or use of such products.
HWB898 1003-5M
© 2003 Alcoa Fastening Systems
1 Corporate Drive, Kingston, NY 12401 • Tel: [phone] • Fax: [phone] • E-mail: [email protected] • www.alcoafasteningsystems.com
Alcoa Fastening Systems world-wide locations:
One Great ConnectionSM