Alderon Industries Mini Power Post PRPT-0003 User manual

Mini Power Post™
Pump Connection Center | Model: PRPT-0003
Safety Guidelines
Step 4: Junction Box Wiring
Before proceeding with the installation or operation of this product,
read all instructions thoroughly, as well as complying with all federal,
state and local codes, regulations, and practices. This product must
be installed by qualied personnel familiar with all applicable local
electrical and mechanical codes. Refer to the National Electrical Code
(NFPA 70). Failure to properly install and test this product can result in
personal injury or equipment malfunction.
WARNING
Step 1: Install Post
QSG00009_Rev07_PRPT-0003_Mini Power Post | October 3, 2022 2:25 PM
Step 2: Remove Bottom Cover
Remove the bottom enclosure cover screw, slide directly downward
(2A) and then pull directly away (2B).
1) Route alarm float switch cable through Cable Grip A and firmly
tighten grip.
2) Route the underground feeder (UF) cable from the indoor alarm
panel through Cable Grip B and firmly tighten grip.
3) Route incoming pump power UF cable through Cable Grip D and
firmly tighten grip.
4) Connect wires in Cable Grip D to the pre-installed Wago
connectors on wires coming out of Cable Grip C as shown in the
diagram.
5) Connect wires coming in Cable Grip A to wires coming in Cable
Grip B as shown in the diagram.
Note: NEVER leave ground wire(s) exposed, use provided Wago
connectors for wire termination (see step 3).
QUICK START GUIDE
2B2A
WAGO
A
GREEN
BLACK
WHITE
BLACK
B
L
A
C
K
B
L
A
C
K
W
H
I
T
E
W
H
I
T
E
WHITE
GROUND
WAGO
WAGO
WAGO
WAGO
B
C
D
Determine location for the post in the
ground near a tank and drill access
holes for the float switch cables using
the customer supplied conduit/fittings or
Alderon’s riser connection kit. Route the
cables through access holes and wire
as described in step 4.
Note: Seal all conduits to prevent moisture and gases
from entering the post per local codes.
Step 3: Install Wire into Wago Connector
1) Lift tab(s) upward.
2) Insert wire(s) into slot.
3) Press tab(s) downward.
4) Make sure wire(s) are secured. TO OPEN
WAGO
TO CLOSE
WAGO

Included with Product
Mini Power Post™- Features
Customer Support
Specications
▪ (1) Mini Power Post™; junction box pre-installed on post
▪ (1) Pre-installed, female, 15A pump power receptacle
(120VAC or 230VAC depending on part number)
▪ (4) Pre-installed cable grips
▪ (1) Junction box partition
▪ (5) Wago connectors; three pre-installed and two additional
Online
alderonind.com
Email
[email protected]
QR Code
Scan code for full product details
Enclosure: Outdoor, rated Type 3R
Certifications: CSA (US and Canada)
Step 5: Install Bottom Cover
Line up the bottom enclosure cover with the grooves (5A), then slide
directly upward (5B) until it meets the top of the enclosure so the screw
hole is lined up and replace the screw at the bottom of enclosure.
Backfill Area:
Once all steps of the installation are finished
and testing is complete, backfill the area you
dug for the post and riser in step 1.
After all wiring and installation steps have been completed, power the system
with incoming voltage(s) to match the pump and alarm voltages. Use the
features list and diagram below to perform a quick test of the system to make
sure it is working properly. Note: For the complete wiring, installation instructions,
or troubleshooting, refer to the user guide for this model by scanning QR code.
1 Vented Post Cap - Allows airow to prevent gases/condensation inside post
2Junction Box Enclosure - Pre-installed on post for easy wiring installation
3Cable Grips - Pre-installed for easy installation
4Partition - Separates high voltage from low voltage
5Pump Power Receptacle (not shown) - Pre-installed, female, 15A
(120VAC or 230VAC depending on part number)
6Post - Provides wire routing access and protection from water intrusion
7 QR Code (not shown) - Scan code for additional product information (alderonind.com)
Backll
Area
Backll
Area
5A 5B
Pump Power Receptacle: 120VAC or 230VAC, 15A, 60Hz
(voltage depends on model/part number)
Pump Power: 120VAC or 230VAC, 13A or 15A, 60Hz
(voltage/amps depends on model/part number)
Step 6: Power System, Test and Backll
1Base Model (Mini Power Post™ Standard) 3Alarm Options
(1-Zone Indoor Alarm, 15' Alarm
Float, and 15' Filter Switch)
5Riser Kit/Access Options (2.5"Riser Connection Kit)
2Pump Voltage (120VAC Pump) 4Pump Switch Options (15A, 15' Wide Angle)
SMP172B2
1 2 3 4 5
Model Number Nomenclature
1
2
3 3
4
6