Alesis DEBUT KIT User manual

User Guide
English ( 3 – 14 )
Guía del usuario
Español ( 15 – 26 )
Guide d’utilisation
Français ( 27 – 38 )
Guida per l’uso
Italiano ( 39 – 50 )
Benutzerhandbuch
Deutsch ( 51 – 62 )
Appendix
English ( 63 )

2

3
User Guide (English)
Introduction
Box Contents
Debut drum rack, assembled including:
Debut sound module
(4) 6” / 15.2 cm drum pads
(3) Cymbal poles
(3) 10” / 25 cm Cymbal pads
(2) Floor pedals (hi-hat and kick)
Cable snake
Sound module power adapter
(2) Sticks
Drum Stool
Headphones
Drum key
Velcro strap
User Guide
Safety & Warranty Manual
Support
For the latest information about this product (system requirements, compatibility information,
etc.) and product registration, visit alesis.com.
For additional product support, visit alesis.com/support.

4
A
A B
A
A
B
Assembly
1. Remove the Debut drum rack,
cymbals and cymbal poles from each
of their boxes.
Place the drum rack (as shown, right)
on a flat, level surface.
2. Unfold the rack legs and loosen the
joints of each rack arm to unfold.
If needed, flip the drum module arm
vertically and then tighten to set it in
place.
Once the kit has been fully expanded,
retighten the joint clamps so the arms
are secure.
3. Insert the cymbal arms to the empty
cymbal clamps on the rack arms and
tighten to secure.
A/B

5
4. Remove the wing-nuts and washers
from each cymbal stand.
Attach the cymbal pads to the poles.
Reattach the wing-nuts and washers
and tighten to secure the cymbal to
the pole.
5. Connect the multipin head of the
included cable snake to the port on
the bottom side of the Debut module.
Tighten the two screws to secure the
cable snake to the module.
6. Connect the labeled 1/4" cables at
the tail end of the cable snake to
each respective drum pad, cymbal
and foot pedal in the drum kit.
Secure the cables using the Velcro
strap.
Feel free to adjust the tension of each
mesh head by evenly tightening each
tension rod with the included drum
key
The tighter the tension, the more
rebound and responsive the drum
head will have. Welcome to your real
drum experience!
crash
hi-hat
snare
ride
tom 3
tom
1
tom
2
hi-hat
control
kick
control

6
Module Features
Top Panel
1. Power Button: Press this button to turn the drum module on. Press and hold it for 2
seconds to turn the drum module off.
2. Display: This screen shows information relevant to the drum module's current function
and operation.
3. Volume Knob: Turn this knob to adjust the volume of the Main Outputs and Phones
Output.
4. – / +: Press either of these buttons to decrease or increase the value shown in the
display.
5. Click Button: Press this button to turn the metronome ("click") on or off. See Using the
Metronome (Click) for more information.
6. Start/Stop Button: Press this button to start or stop playback of a pattern. See Playing
Along with Patterns for more information.
7. Pattern Button: Press this button to enter Pattern Mode. Press both this button and the
Tempo Button simultaneously to use the Built-In Drum Coach. See Playing Along with
Patterns and Using the Built-In Drum Coach for more information.
8. Tempo: Press this button to enter Tempo Mode and use the – / + buttons to adjust the
tempo. Press both this button and the Pattern Button simultaneously to use the Built-In
Drum Coach. See Using the Metronome (Click) and Using the Built-In Drum Coach
for more information.
9. 1-5/Variation Buttons: Press any one of these buttons to enter Kit Mode and select a
Kit. When using the Built-In Drum Coach, you can use these buttons to select an
exercise. See Using Kits and Using the Built-In Drum Coach for more information.
123
4
5678
9

7
Rear Panel
1. Power Jack: Use the included power adapter (9 V, 500 mA, center pin-positive) to
connect this jack to your power outlet.
2. Cable Snake Input: Connect the head of the included cable snake here. Connect the
cables at the tail end of the cable snake to your kit's triggers (drum pads, cymbal pads,
and pedals).
3. Main Outputs: Use standard 1/4" mono cables (not included) to connect these outputs
to your monitor, amplifier, or PA system. Adjust the volume of these outputs with the
Volume Knob on the top panel.
4. Phones Output: Connect standard 1/8" stereo headphones (not included) to this output.
Adjust the volume of this output with the Volume Knob on the top panel.
5. Aux In: Use a 1/8" stereo cable (not included) to connect an external audio device
(smartphone, CD player, etc.) to this input.
6. USB Port: Use a standard USB cable (not included) to connect your computer to this
port, which allows you to send and receive MIDI messages to and from your computer.
See MIDI for more information.
Operation
Playing the Pads
Try hitting the pads with different amounts of force to experiment with the different sounds
produced by the module!
The hi-hat sound will vary based on the position of the hi-hat controller pedal:
•Open hi-hat: With your foot off the pedal, hit the hi-hat pad.
•Closed hi-hat: With your foot pressing the pedal all the way down, hit the hi-hat
pad.
•Pedal close: Press the hi-hat pedal all the way down without hitting the hi-hat pad.
•Splash: Quickly press the hi-hat pedal all the way down, and then release it
immediately.
1
2
3
456

8
Selecting a Kit
To select one of the module's 10 preset kits, do
one of the following:
•Press the Variation button so it is lit red,
and then press the 1, 2, 3, 4, or 5button to
select Kit 1, 2, 3, 4, or 5respectively.
•Press the Variation button so it is lit green, and then press the 1, 2, 3, 4, or 5
button to select Kit 6, 7, 8, 9, or 10 respectively.
The Kit Number will appear in the Display. Once you have selected a kit, you can select others
by repeating one of the steps above or by using the – / + buttons.
Adjusting Kit Volumes
To adjust the volume of each separate kit:
1. Do one of the following:
•With the Variation button lit red, double-
press the 1, 2, 3, 4, or 5button to select
Kit 1, 2, 3, 4, or 5 respectively.
•With the Variation button lit green,
double-press the 1, 2, 3, 4, or 5button to
select Kit 6, 7, 8, 9, or 10 respectively.
2. The Display will show the volume level (L00 – L32). Use the – / + buttons to
set the kit's volume level (the default volume level is L28).
3. Wait 4 seconds. The kit’s new volume setting will be saved automatically.
Playing Along with Patterns
Selecting and Playing a Pattern
To select one of the 30 preset patterns:
1. Press the Pattern button to enter Pattern Mode. The button's LED will light
up, and the Display will show the current Pattern Number.
2. Use the – / + buttons to select a pattern. (You can hold down the –or +
button to scan quickly through the list).
3. Press the Start/Stop button to start the pattern's playback.
4. Play along to the pattern!
5. Press the Start/Stop button to stop the pattern's playback.
Adjusting the Pattern Volume
To adjust the volume of each separate pattern:
1. Double-press the Pattern button.
2. The Display will show the volume level (00 – 32). Use the – / + buttons to set
the pattern's volume level (the default volume level is 25).
12345 VARIATION
PATTERN
START
/STOP
PATTERN
12345 VARIATION

9
Using the Metronome (Click)
You can use the built-in metronome ("click") to help you keep time while practicing with the built-in
Drum Coach or with patterns. You can change the metronome's tempo (speed), volume, sound, and
time signature.
Turning the Metronome On or Off
To turn the metronome on or off, press the Click button.
Adjusting the Metronome Tempo
To adjust the metronome's tempo (speed):
1. Press the Tempo button.
2. The Display will show the current tempo (30 – 280) in BPM ("beats per
minute"). Use the – / + buttons to set the new tempo.
3. Wait 4 seconds. The drum module will automatically save the new setting.
Adjusting the Metronome Volume
To adjust the metronome's volume:
1. Double-press the Click button.
2. The Display will show the volume level (L00 – L32). Use the – / + buttons to
set the metronome's volume level (the default volume level is L25).
3. Wait 4 seconds. The drum module will automatically save the new setting.
Changing the Metronome Sound
To change the metronome's "click" sound:
1. Press the Click button and 1button simultaneously.
2. The Display will show CL ("click") and the number of the sound (CL1 –
CL5). Use the – / + buttons to set the metronome sound:
•CL1: Chime and click (default)
•CL2: Clave
•CL3: Side-stick
•CL4: Cowbell
•CL5: Vocal
3. Wait 4 seconds. The drum module will automatically save the new setting.
Changing the Metronome Time Signature
To change the metronome's time signature:
1. Press the Click button and 2button simultaneously.
2. The Display will show the current time signature. Use the – / + buttons to
select a time signature: 1/2, 2/2, 3/4, 4/4, or 6/8.
3. Wait 4 seconds. The drum module will automatically save the new setting.
TEMPO
CLICK
CLICK
CLICK
1
CLICK
2

10
Changing the Metronome Interval
To change the metronome's note division (the note value it measures with each click):
1. Press the Click button and 3button simultaneously.
2. The Display will show the current interval. Use the – / + buttons to select a
new interval: 2 (half note), 3 (triplet),4 (quarter note), 6 (sextuplet),8 (eighth
note), or 16 (sixteenth note). The default is 4.
3. Wait 4 seconds. The drum module will automatically save the new setting.
Using the Built-In Drum Coach
The Built-In Drum Coach contains five different exercises to help you develop and improve your
accuracy, stamina, and sense of tempo: Beat Check, Gradual Up/Down, Rhythm Change Up,
Follow Me, and Drum Mute.
To use the Built-In Drum Coach, press the Pattern button and Tempo button at the same time.
Then, press the 1, 2, 3, 4, or 5button that corresponds to the exercise you want to do. The Display
will show which exercise you have selected:
1. Beat Check (bCH)
2. Gradual Up/Down (GUd)
3. Rhythm Change Up (C-U)
4. Follow Me (FLo)
5. Drum Mute (d-U)
Beat Check
This exercise evaluates your sense of timing and how accurately you play along with the metronome.
To use Beat Check:
1. Press the Pattern button and Tempo button at the
same time. Then press the 1button.
2. Set the metronome's time signature and interval (as
described in Using the Metronome (Click)).
3. Press the Start/Stop button to begin.
4. Hit the pads in time with the metronome. The six
LEDs of the 1-5/Variation buttons indicate how
accurate or "in time" you are.
•When you are right on the beat, the 3
and 4buttons light up.
•When you are slightly off the beat, the 2
or 5button will light up.
•When you are off the beat, the 1or
Variation button will light up.
•When you are completely off the beat, no
buttons will light up.
5. Press the Start/Stop button to stop.
CLICK
3
START
/STOP
SLOW GOOD FAST
12345VARIATION
PATTERN
COACH
TEMPO
1

11
Gradual Up/Down
This exercise evaluates how quickly you can play while still maintaining accurate time.
To use Gradual Up/Down:
1. Press the Pattern button and Tempo button at the
same time. Then press the 2button.
2. Set the metronome's time signature and interval (as
described in the Using the Metronome (Click) section).
3. Press the Start/Stop button.
4. Do one of the following:
•Press the 1button to select G-1 Mode. In this mode, the
tempo automatically decreases or increases by 5 BPM every
4 measures, depending on your accuracy.
•Press the 2button to select G-2 Mode. In this mode, the
tempo automatically decreases or increases by 1 BPM each
measure (The starting tempo is your metronome's current
setting).
5. Hit the pads in time with the metronome. The six LEDs of the 1-5/Variation buttons indicate
how accurate or “in time” you are.
•When you are right on the beat, the 3
and 4buttons light up.
•When you are slightly off the beat, the 2
or 5buttons will light up.
•When you are off the beat, the 1or
Variation button will light up.
•When you are completely off the beat,
no buttons will light up.
6. Press the Start/Stop button to stop.
Rhythm Change Up
This exercise helps you practice changing rhythms while still maintaining accurate time.
To use Rhythm Change Up:
1. Press the Pattern button and Tempo button at the
same time. Then press the 3button.
2. Press the Start/Stop button.
3. Press the 1, 2, or 3button or use the – / + buttons to select a rhythmic
progression, shown below:
P-1:
P-2:
P-3:
4. Press the Start/Stop button to begin.
START
/STOP
1
2
SLOW GOOD FAST
12345 VARIATION
START
/STOP
123
PATTERN
COACH
TEMPO
2
PATTERN
COACH
TEMPO
3

12
5. Hit the pads in the rhythm you selected (above) and in time with the metronome (the starting
tempo is your metronome's current setting). The six LEDs of the 1-5/Variation buttons indicate
how accurate or “in time" you are:
•When you are right on the beat, the 3
and 4buttons will light up.
•When you are slightly off the beat, the 2
or 5button will light up.
•When you are off the beat, the 1or
Variation button will light up.
•When you are completely off the beat, no buttons will light up.
The Display will show your score:
•0 – 29: OK
•30 – 59: Good
•60 – 79: Very Good
•80 – 100: Excellent
Follow Me
This exercise helps you identify different drums by their sound and memorize drum rhythms that use
the entire drum kit. In this exercise, the drum module will alternate between (1) a drum pattern and (2)
a metronome track of the same length during which you play the drum pattern yourself.
To use Follow Me:
1. Press the Pattern button and Tempo button at the
same time. Then press the 4button.
2. Press the Start/Stop button.
3. Use the – / + buttons to select the drum pattern you
want to play in.
4. Press the Start/Stop button to begin.
5. When you hear the drum pattern, try to
identify which pads are being played and
when. During the metronome track that
follows, play the same drum pattern in time
with the metronome. For reference, the
Display will show the current beat. The six
LEDs of the 1-5/Variation buttons indicate
how accurate you are.
6. Press the Start/Stop button to stop.
SLOW GOOD FAST
12345 VARIATION
PATTERN
COACH
TEMPO
4
SLOW GOOD FAST
12345 VARIATION
START
/STOP

13
Drum Mute
This exercise lets you silence specific parts of various drum patterns so that you can test different
drumming techniques as you fill in the gaps while playing along with the pattern.
To use Drum Mute:
1. Press the Pattern button and Tempo button at the
same time, and then press the 5button.
2. Press the Start/Stop button.
3. Use the – / + buttons to select the drum pattern you want to play to.
4. Press one or several of the 1-5/Variation buttons to select the sound or
sounds you want to mute:
•1: Kick drum
•2: Snare drum
•3: Hi-hat
•4: Toms
•5: Crash and ride cymbals
•Variation: Percussion
5. Press the Start/Stop button to begin.
6. Play freely along with the drum pattern you hear. The drum pattern will not include any sounds
you muted in Step 4, allowing you to create your own part.
7. Press the Start/Stop button to stop.
Automatic Power-Off
To save energy, the drum module will power off automatically after 30 minutes of no activity. If you
do not need this feature, disable it by powering off the drum module and then pressing and holding
the Start/Stop button while powering it back on. PoF will appear on the display to confirm the
feature is off.
Note: After powering off, this feature will be re-enabled. Repeat the procedure described above to
disable the feature when you power on the module again.
MIDI
About MIDI
MIDI (Musical Instrument Digital Interface) is a standard way in which certain electronic musical
devices can communicate with each other. When two MIDI devices are connected, they can
send/receive MIDI "messages" over either a 5-pin MIDI cable or a standard USB cable (depending
on ports available on the devices).
In the case of the Debut Drum Module, you can connect its USB port to a USB port on your
computer with a standard USB cable (sold separately). All MIDI messages will travel to and from your
computer over this connection. This allows you to do one of two things:
•Use an electronic drum kit connected to the drum module to trigger sounds on an external MIDI
device (e.g., a sequencer, your computer if you use software that can receive MIDI notes, etc.).
See Triggering Sounds on an External MIDI Device later in this section.
•Use an external MIDI device to play sounds in the drum module. See Using the Drum Module
as the Sound Module later in this section.
START
/STOP
PATTERN
COACH
TEMPO
5

14
Triggering Sounds on an External MIDI Device
MIDI INVOL MIDI OUT R L R L USB
1. Using a standard USB cable (not included), connect the drum module's USB port to a
USB port on your computer.
2. If you are triggering sounds in software, skip to the next step.
If you are triggering sounds in an external MIDI device, make sure that device is
connected to your computer (either directly via USB or through a USB-MIDI interface).
3. Set the active track of your MIDI software, sequencer, etc. to Channel 10, and start
recording.
4. Play your electronic drum kit. The MIDI information will be sent to your computer,
sequencer, etc.
5. Stop recording.
Using the Drum Module as the Sound Module
MIDI INVOL MIDI OUT R L R L USB
1. Using a standard USB cable (not included), connect the drum module's USB port to a
USB port on your computer.
2. If you are using software to play the drum module's sounds, skip to the next step.
If you are using an external MIDI device to play the drum module's sounds, make
sure that device is connected to your computer (either directly via USB or through a USB-
MIDI interface).
3. Set the active track of your MIDI software, sequencer, etc. to the desired channel (1-16).
Note: Channel 10 of the drum module is reserved for drum sounds.
4. Play your sequencer or other external device to hear the drum module's internal sounds.

15
Guía del usuario (Español)
Introducción
Contenido de la caja
Batería electrónica Debut ensamblada, incluyendo:
Módulo de sonido Debut
(4) Pads de tambor de 6 pulg. / 15,2 cm
(3) Soporte para platillos
(3) Pads de platillos de 10 pulg. / 25 cm
(2) Pedales (hi-hat y bombo)
Manojo de cables
Adaptador de corriente del módulo de sonido
(2) Baquetas
Banqueta para batería
Auriculares
Llave de ajuste de tambores
Tira de velcro
Guía del usuario
Manual sobre la seguridad y garantía
Soporte
Para obtener la información más completa acerca de este product (los requisitos del sistema,
compatibilidad, etc) y registro del producto, visite alesis.com.
Para soporte adicional del producto, visite alesis.com/support.

16
A
A B
A
A
B
Instalación
1. Retire la estructura de la Debut, los
platillos y soportes para platillos de
cada una de sus cajas.
Coloque la estructura (como se
muestra a la derecha) sobre una
superficie plana y nivelada.
2. Despliegue las patas de la
estructura y afloje las articulaciones
de cada brazo de la estructura para
poder desplegarlos.
De ser necesario, incline el módulo
de batería para que quede más
vertical y luego ajústelo para que
quede firme en esa posición.
Una vez que el kit se haya
desplegado completamente, vuelva
a apretar las abrazaderas de
articulación para que los brazos
queden firmes.
3. Inserte los soportes de platillo en las
abrazaderas de platillo vacías en los
brazos de la estructura y apriételas
hasta que queden firmes.
A/B

17
4. Retire la tuerca mariposa y la
arandela de cada soporte de platillo.
Inserte los pads de platillo en los
soportes.
Vuelva a colocar las tuercas
mariposa y las arandelas, y
apriételas hasta que los platillos
queden firmemente sujetos a los
soportes.
5. Enchufe el cabezal multiconector del
manojo de cables incluido en el
conector que se encuentra del lado
inferior del módulo del Debut.
Apriete los dos tornillos para sujetar
el manojo de cables al módulo.
6. Conecte los cables de 1/4 pulg. del
manojo a sus respectivos pads de
tambor, platillo y pedal de la batería
según la etiqueta en el extremo de
cada uno los cables.
Sujete los cables utilizando las tiras
de velcro.
Siéntase libre de ajustar la tensión de
cada cabezal de malla apretando
uniformemente cada barra de tensión
con la llave del tambor incluida
Cuanto más apretada sea la tensión,
más rebote y capacidad de respuesta
tendrá la cabeza del tambor.
¡Bienvenido a tu verdadera
experiencia de batería!
Platillo
crash
hi-hat
Ca
j
a
Platillo
r
ide
tom 3
tom
1
tom
2
Control
de hi-hat
Control
de
bombo

18
Características
Panel superior
1. Botón de encendido: Pulse este botón para encender el módulo de batería. Manténgalo
pulsado 2 segundos para apagar el módulo de batería.
2. Pantalla: Esta área muestra valores y texto relevantes de las funciones y la operación del
módulo de batería.
3. Perilla de volumen: Gire esta perilla para ajustar el volumen de las salidas Main
(Principal) y Phones (Auriculares).
4. – / + : Pulse alguno de estos botones para aumentar o disminuir el valor que se muestra
en la Pantalla.
5. Botón de clic: Pulse este botón para activar o desactivar el metrónomo ("clics"). Para
más información, consulte la sección Funcionamiento > Usar el metrónomo (clic).
6. Botón de inicio/parada: Pulse este botón para iniciar o detener la reproducción de un
patrón. Para más información, consulte la sección Funcionamiento > Tocar con
acompañamiento de patrones.
7. Botón de patrón: Pulse este botón para entrar al modo de patrón. Pulse
simultáneamente este botón y el botón Tempo para usar el instructor de batería
integrado. Para más información, consulte las secciones Funcionamiento > Tocar con
acompañamiento de patrones y Usar el instructor de batería integrado.
8. Tempo: Pulse este botón para entrar al modo Tempo y use los botones – / + para ajustar
el tempo. Pulse simultáneamente este botón y el botón Pattern para usar el instructor de
batería integraado. Para más información, consulte las secciones Funcionamiento >
Usar el metrónomo (clic) y Usar el instructor de batería integrado.
9. Botones de 1-5/variación: Pulse cualquiera de estos botones para entrar al modo de kit
y seleccione un kit. Cuando usa el instructor de batería integrado, puede usar estos
botones para seleccionar un ejercicio. Para más información, consulte las secciones
Funcionamiento > Usar los kits y Usar el instructor de batería integrado.
123
4
5678
9

19
Panel trasero
1. Conector hembra de alimentación: Use el adaptador de alimentación incluido (de 9 V,
500 mA, pin central positivo) para conectar este conector hembra al tomacorriente.
2. Conector del multicable: Conecte aquí su multicable incluido y conecte los cables del
multicable a los disparadores de su kit (pads de tambor, pads de platillos y pedales).
3. Salidas principales: Use cables mono estándar de 1/4 pulg. (no incluidos) para conectar
estas salidas a su monitor, amplificador o sistema de megafonía. Ajuste el volumen con
la perilla Volume del panel superior.
4. Salida para auriculares: Conecte a esta salida auriculares estéreo estándar de 1/8 pulg.
(no incluidos). Ajuste el volumen con la perilla Volume del panel superior.
5. Entrada auxiliar: Use un cable estéreo de 1/8 pulg. (no incluido) para conectar a esta
entrada un dispositivo de audio externo (teléfono inteligente, reproductor de CD, etc.).
6. Puerto USB: Use un cable USB estándar (no incluido) para conectar su computadora
este puerto, permitiéndole enviar y recibir mensajes MIDI hacia y desde la misma. Para
más información, consulte la sección MIDI.
Funcionamiento
Cómo tocar los pads
Si su kit de batería electrónica tiene pads sensibles a la velocidad, Debut Drum Module reproducirá
sonidos de timbres variables que dependen de la fuerza con que golpee los pads. ¡Trate de golpear
los pads con fuerzas diferentes para experimentar los distintos sonidos que produce el módulo!
El sonido del hi-hat varía en función de la posición del pedal controlador de hi-hat:
•Hi-hat abierto: Con su pie levantado del pedal, golpee el pad del hi-hat.
•Hi-hat cerrado: Con su pie presionando el pedal a fondo, golpee el pad del hi-hat.
•Cierre de pedal: Presione el pedal del hi-hat a fondo sin golpear el pad del hi-hat.
•Salpicado: Presione rápidamente el pedal del hi-hat a fondo y luego suéltelo
inmediatamente.
1
2
3
456

20
Cómo seleccionar un kit
Para seleccionar uno de los 10 kits preprogramados del módulo, realice uno de los siguientes
procedimientos:
•Pulse el botón Variation de modo que se
ilumine verde y luego pulse el botón 1, 2, 3, 4
o 5para seleccionar el Kit 1, 2, 3, 4 o 5
respectivamente.
•Pulse el botón Variation de modo que se
ilumine rojo y luego pulse el botón 1, 2, 3, 4 o
5para seleccionar el Kit 6, 7, 8, 9 o 10
respectivamente.
El número del kit aparece en la Pantalla. Una vez que haya seleccionado un kit, puede seleccionar
otros repitiendo uno de los pasos precedentes o usando los botones – / +.
Ajustar los volúmenes de los kits
Para ajustar el volumen de cada kit por separado:
1. Seleccione una de los siguientes procedimientos:
•Con el botón Variation de encendido en
rojo, pulse dos veces el botón 1, 2, 3, 4 o
5para seleccionar el kit 1, 2, 3, 4 o 5
respectivamente.
•Con el botón Variation de encendido en
verde, pulse dos veces el botón 1, 2, 3, 4 o 5para seleccionar el kit 6, 7, 8, 9 o 10
respectivamente.
2. La Pantalla muestra el nivel de volumen (L00 – 32). Use los botones – / +
para ajustar el volumen del kit (el nivel de volumen predeterminado es L28).
3. Espere 4 segundos. El módulo de batería guarda automáticamente el
nuevo ajuste.
Tocar con acompañamiento de patrones
Seleccionar y tocar un patrón
Para seleccionar uno de los 30 patrones:
1. Pulse el botón Pattern para entrar al modo de patrón. Se enciende el LED del botón y
aparece en la Pantalla el número del patrón actual.
2. Use los botones – / + para seleccionar un patrón (puede mantener pulsados
los botones – / + para recorrer rápidamente la lista).
3. Pulse el botón Start/Stop para iniciar inmediatamente la reproducción del patrón.
4. ¡Toque con el acompañamiento del patrón!
5. Pulse el botón Start/Stop para detener inmediatamente la reproducción del patrón.
Ajustar el volumen del patrón
Para ajustar el volumen de cada patrón por separado:
1. Pulse dos veces el botón Pattern.
2. Aparece en la Pantalla el nivel de volumen (00 – 32). Use los botones – / +
para ajustar el nivel de volumen del patrón (el nivel de volumen
predeterminado es 25).
PATTERN
12345 VARIATION
START
/STOP
PATTERN
12345 VARIATION