6
Double mitre saw
T300-T350- T300/A-T350/A-T400
PRELIMINARY 05.1998
2.9 TECHNICAL DATA
Here below are indicated Machine technical data and
characteristics to which make reference for any eventual
contact with Producer Technical Assistance.
Table 2.9 A – DATA AND CHARACTERISTICS
Length of right working bench extension 1200 mm
Length of left working bench extension 1200 mm
Working bench length 800 mm
Working bench height (from the floor) 950 mm
Motors power n.2 1.5 kW
Max revolutions per minute 2800 n/’
Pneumatic feed 5/7 bar
Power Consumption 3 kW
Profiles width (Min/Max) T300 – T300/A 15/60
T350 – T350/A 15/80
T400 15/100
Profiles height (Min/Max) T300 – T300/A 10/60
T350 – T350/A 10/80
T400 10/100
Electric power supplying 400V/230V
Suction holes ∅80 mm
Total weight about 380 Kilos
2.10 TOOLS
2.4 DIMENSIONS
The overall dimensions are reported on complete drawing
of attachment 10.2-A
2.5 SURROUNDING CONDITIONS
The machine does not need special surrounding conditions.
It has to be installed inside an industrial building, lit, aired
and with a compact and flat floor. The admitted temperatures
go from 5° to 40° C, with an humidity not higher than 50%
at 40° C or 90% at 20° C.
2.6 LIGHTING
Premises lighting must be conformed to the norms in force
in that Country where the machine is installed and has to
guarantee a clear visibility, do not create dangerous
reflections and allow a clear reading of the control panel
and the location of emergency button.
2.7 VIBRATIONS
In standard conditions conformed to the indication of
machine proper utilization (the machine is anchored to the
ground by 4 fastening points), the vibrations do not create
dangerous conditions.The average quadratic weighed level,
according to the acceleration frequency to which arms are
exposed does not exceed 2,5 m/s2.
2.8 NOISE EMISSIONS
The machine is designed and projected for reducing the
noise emission level to its source. Tests have been effected
according to the measurement method conformed with Art.
46 D.Lgsl. 277/91.
The T350 Double Mitre Saw , when workings on standard
and correct conditions of use, produces a sound level per
operator lower than 85 bB (A) even if used continuously.
For this survey has been considered the cut of hardwood
type Ramin which can be used for manufacturing of picture
frames. The use of softer woods (i.e. Obeche) produces
sound levels lower of about 2-3 dB (A).
The noise levels indicated are emission levels and are not
representing sure operating levels. In spite of existing a
relationship among emission levels and exposure ones, this
can not be used in a reliable way to define if further cautions
are necessary. The factors determining the exposure level
to which the working force is subjected, include exposure
lasting, working premises characteristics and other noise
sources (number of machines, closed proceeds, etc…).
Furthermore, also the allowed exposure levels could change
according to the several Countries. At any rate, the
information provided, will allow the Machine Operator to
achieve a better evaluation of danger and risks he is
submitted to.
Blades, conformed to the Norm EN 847-1
The indicated noise levels are emission ones
measured in standard conditions of use. In
case of any machine modification, the above
mentioned levels could be changed and
should be settled directly on the same
machine.
Blades, conformed to the Norm EN 847-1, have the
following dimensions:
•A =30 mm
•B =300 mm (model T300 – T300/A)
=350 mm (model T350 – T350/A)
=400 mm (model T400)
•Thickness =2.50 mm
Use the machine only if equipped with
special individual protections for hearing (
headphones etc…).
The customer can request different types of blades
according to the materials to be cut (light alloys,
wood or plastic).
