AlienPro ALPHA-S User manual

alienpro.com.mx
MANUAL DE USUARIO
ALPHA - S

Thank you for purchasing this product. To optimize the performance of this product,prior to
use,please read these operating instructions carefully to familiarize yourself with the basic operation
of this unit.Please keep the manual in safe price for future reference. This unit has been tested at our
factory before being shipped to you, there is no assembly required. Once after received this product
, please take and put carefully. And check cautiously that whether the product was damaged or not
during the transportation.
1
www.alienpro.com.mx
Please check if the following parts are included:
1 x Laser light
1 x User manual
1 x Power cable
Checking Parts
Foreword
Caution
Symbol Instruction On The Device
--------------------------------------------------------------------- CE Certificate
-------------------------------------------------------------------- Only indoor use
---------------------------------------------------------- Environmental protection
----------------------------------- The minimum distance from lighted objects(meter)
--------------------------------------------------------------- Max. Ambient Temp
---------------------------------------------------------------- Max. Housing Temp
--------------------------------------------------------------------- Safety caution
---------------------------------------------------------------------- Careful burns
-------------------------------------------------------------- Careful electric shock
----- Not suitable for directly installed on the surface of ordinary combustible materials
Unplug mains lead before opening the housing!
Damages caused by the disregard of this user manual
are not subject to warranty. The dealer will not accept
liability for any resulting defects or
Keep this device away from rain and moisture!
8
www.alienpro.com.mx
Maintenance should be performed every 15-day period, by using a sponge which is dipped with
alcohol, rather than wet cloth or other chemical liquid, to clean the mirror.
Always disconnect from the mains when the device is not in use or before cleaning it.
Cleaning and maintenance
Warranty Card
¡Caution!
Make sure power off before cleaning and maintenance!
¡Warning!
Any power connected must by professional person.
¡Warning!
Never look directly into the light source,as sensitive
persons may suffer an epileptic shock(especially meant
for epileptics)!
This product is made of high -brightness transistor. We will provide 1 year warranty
under the condition that user has operated the light normally and lifetime service.
We won't provide warranty if the damage is caused by artificial or force majeure
event. Cost of fittings should be charged by user if product need maintenance after
1 year .Please cut this warranty card and shipped it along with the product to our
factory when applying for warranty.
Product
：
Purchasing date：
Code of invoice
：
Warranty date: From To
User’s name
：
Add
：
Company
：
Tel
：

2
www.alienpro.com.mx
Safety Instructions
Installation
- Please open and check whether break or not for transport once receive this fixture, if yes, not use
it and contact dealer or manufacture as soon as possible.
- The Max applicable temperature for the light is 40°C. Do not use the light under or above the
temperature. ta=40
- The fixture is applicable for many occasions, it should keep clean, and avoid long use in overheating
or dusty environment. To prevent the fixture from the chemical liquid .
- User must be careful of fire, heat, electric and fall-off that make heavy or fatal injury. Please read
this user manual carefully before power on and installation, following safety and operation instruc-
tion in it. If still have any questions, please contact dealer or manufacture.
- User must following this user manual, do not open fixture by yourself, if any problems, please
contact professional technician, maintenance should by technician.
- Do not power on or start the fixture before installation, please stop after working more than 8
hours, which will longer use life.
- Fixed installation, do not by strong shocks.
- The minimum distance between light and the illuminated surface must be more than 1 meter.
- Never look directly into the light source to avoid hurt to eyes (especially epileptics)!
- When dustproof glass at light output breaks, cracks or other visible damage, user should replace
with new glass to continue to use.
- When install this equipment please make sure there's no flammable surfaces (decorated things,
etc) and minimum distance of 0.5M from the equipment to the flammable.
- The installation of the effect has to be built and constructed in a way that it can hold 10 times the
weight and without any harming deformation.
- The installation must always be secured with a secondary safety attachment, e.g. an appropriate
safety rope. Never stand directly below the device when mounting, removing or servicing the fixture.
Technical Specifications
Input voltage: AC127V, 60Hz
Fuse: BGDP ￠5x20mm 250VAC T2A
Total power: 30W
Light source: R:250mw/638nm，G:100mw/532nm，B:500mw/445nm
Control mode: Auto/Sound/DMX512
Channels：16CH
Scanning system: 10Kpps Scanner, ±15º
Surface temp: Tb=40ºC ( this data testing when the environment temp is 30ºC)
Working temp: 10ºC--65ºC
Modulation: TTL
N.W: 4.0Kg
G.W: 4.5Kg
Inner packing size: 36X30X16cm
Outer packing size: 70X38X32cm(4pcs/ctn)
1 Mounting bracket
2 Handle
7
www.alienpro.com.mx
A) The ambient temperature range is -25°C--45°C, must never be exceeded.
B) The installation of the projector has to be built and constructed in a way that it can hold 10 times
the weight for 1 hour without any harming deformation.
C) When rigging, derigging or servicing the fixture staying in the area below the installation place, on
bridges,under high working places and other endangered areas is forbidden.
D) The operator has to make sure that safety-relating and machine-technical installations are
approved by an expert before taking into operation for the first time and after changes before taking
into operation another time.
E) The operator has to make sure that safety-relating and machine-technical installations are
approved by a skilled person once a year.
F) Sure M8 screws on mounting bracket fixed middle hole ¢12.5mm of handle
Ringing
Product size
Wiring diagram

3
www.alienpro.com.mx
- When press dip switch 1, the unit works in fixed geometry program
- When press dip switch 2,the unit works in fixed animation program
- When all dip switches are off, fixture runs music mode.
- When press dip switch No.10 ,it will be controlled by DMX512,No.1-9 dip switches are address
code.
Functions Instruction
Channel Instructions
Channel Function Value Details
CH1
Control
Mode
0~63
64~127
128~191
192~255
Close light
Sound Active
Auto-Play
DMX Control(Manual adjust)
CH2 Color
0~20
21~41
42~62
63~83
84~104
105~125
126~146
147~167
168~188
189~209
210~230
231~251
252~255
No function
Original color
Red
Yellow
Green
Cyan
Blue
Purple
White
Auto-change color randomly
Auto-change single color randomly
Seven color change
Dotting effect
CH3
Select
Pattern
0~255 32 Patterns（0-255）/8=0~31
CH4
Select
Pattern
Group
0~255
4 Pattern groups（0-255）/64=0~3
CH5
Horizontal
Rotate
0~127
128~191
192~255
Horizontal rotation（0~360 degree）
Horizontal clockwise rotation speed
（8 grade）
Horizontal counter - clockwise
rotation speed
（
8 grade
）
CH6
Vertical
Rotate
0~127
128~191
192~255
Vertical rotation
（
0~360 degree
）
Vertical clockwise rotation speed （8
grade）
Vertical counter - clockwise rotation
speed （8 grade）
CH7
Center
Rotate
0~127
128~191
192~255
Center rotation
（
0~360 degree
）
Center clockwise rotation speed （8
grade）
Center counter- clockwise rotation
speed
（
8 grade
）
CH8
Horizontal
Move
0~127
128~255
Horizontal move
Horizontal movement speed (8 grade)
CH9 Vertical
Move
0~127
128~255
Vertical move
Vertical movement speed(8 grade)
CH10
Horizontal
Stretch
0~127
128~255
Horizontal stretch
Horizontal stretch speed (8 grade)
CH11
Vertical
stretch
0~127
128~255
Vertical stretch
Vertical stretch speed (8 grade)
DMX Address setting
6
www.alienpro.com.mx
No. Drawing code Spare parts
Qty/u
nit
Materials Materials code
1
RGB-244B-02
Base plate
1
iron plate
311003112
2
RGB-244B-03
Head cover
1
iron plate
311006074
3 RGB-244-03 Handle 1 iron plate 316001060
4 RGB-244B-04 FPC 1
aluminium plate
315001101
5
RGB-151-14
High-reflective mirror stand
3
galvanized plate
313005026
6 RG-043-08 light barrier 2
aluminium plate
312005001
7
RGB-244B-07
Laser stent
2
galvanized plate
313003009
8
250V/10A
，
fuse
AC power socket
1
301923002
9
KCD-101
，
M size
Rocker Switch
1
301916001
10
SPL111
Plate connected with XLR
1
301904072
11
OUT，vertical
3-pins XLR
1
301909008
12
IN
，
vertical
3-pins XLR
1
301909007
13
PCBA
，
12V-3A
，
36W
Switch power
1
204001001
14
SPL031
，
2.6*1.5cm
（
one
side
）
PCB control board 1 301904022
15
B1M-15mm
，
plastic handle
Potentiometer
1
301012002
16
￠12
Safety lock
1
308010001
17
M6
Hanging ring
1
306019002
18
￠
8 black
，
rubber
protective ring
1
303008001
19
KRT-1204
self-adhesion machine leg
4
303006001
20 70×30mm
insulating plate
2 301904096
21
PCBA
，
12V-3A
，
36W
Switch power
2
306020002
22
￠
16*
￠
6*2.0mm
Rubber mat
4
303002003
23
6*6*1.5cm，DC12V,0.15A
Fan
1
301701007
24
15*15*1.1mm,class A
High-reflective mirror
1
302010025
25
15*15*1.1mm
，
class A
Pass green, reflect red
1
302003009
26 15*15*1.1mm,class A
Pass red and green,
reflect blue
1 302006007
27
53*53*1.1mm double-deck
coating film
Dustproof mirror 1 302015032
28
10K RGB main board
Scanner main board
1
205013001
29 Mini 10K scanner 1 206001004
30 2A/250V，￠5*20
protective tube
2 301906002
31
250MW/638NM
SPC-LR30A+SPE-B01
1
201119011
32 100MW/532NM SPO-G35A+LB-G1 1 201104004
33 500MW/450NM SPL-B30A+LB-B1 1 201111006

Each fixture must set a specific starting address. When receiving signal transmission, fixture will
receive channel control signals which from the starting address.
According to different requirements or easy to use, the user can set many value fixtures to the same
address, also can set up a separate address for every device.
If you set the same address,all the devices will receive from DMX channels signal. All connecting
fixtures are jointly controlled, controller can't separate control a device.
If you set a different address, each device will be separate from its particular set the starting address
and begin accepting DMX512 control signal, so that more convenient separate control one device.
Using this method must be based on channel quantity of device to determine a starting address.
This laser light has 16 channels.you should set the starting address of the first unit to 1, the second
unit to 17(1 + 16), the third unit to 33 (16*2+ 1), and so on.
DMX In To the fourth
First light (Address 001) Second light (Address 017) Third light(Address 033)
Press1,10 Press1,5,10 Press1,6,10
Channel Instructions
DMX-512 connection
Dip switch and value
DMX Address setting
DMX Address setting
4
www.alienpro.com.mx
5
www.alienpro.com.mx
Dip
Switch
1
2
3
4
5
6
7
8
9
10
Value
1
2
4
8
16
32
64
128
256
DMX
CH12 Pattern
Size
0~2
3~127
128~169
170~211
212~255
Original size
Pattern size from small to big ( 127
grade)
Pattern dynamic zoom from small to
big (41 grade)
Pattern dynamic zoom from big to
small (41 grade)
Pattern dynamic cycle zoom ( 41
grade)
CH13
Slow
Drawing
0~3
4~255
No function
Slow drawing speed (16 grade)
CH14
Scanning
Speed
0~2
3~255
Default scanning speed (value:6)
252 grade scanning speed
CH15
Color
Speed
0~255 256 grade(slow to fast)
CH16
Strobe
Speed
0~255
9 grade strobe speed
（
0-255
）
/31=0~8(0 grade no flash)