All Pond Solutions PFC-5000 User manual

PRESSURISED SPIN CLEAR
POND FILTER
PFC-5000 / 8000 / 12000
/ 20000 / 25000 / 30000 / 50000
FILTRE DE BASSIN PRESSURISE DE NETTOYAGE ROTATIF OUTPUT
CONTROL DIAL
FILTRO PER LAGHETTO PRESSURIZZATO CON ROTAZIONE
FILTRO PRESURIZADO PARA ESTANQUES CON REMOCIÓN MEDIANTE
GIROS CONTAMINANTES
SPIN CLEAR TEICH-DRUCKFILTER

To ensure your new pond filter is set up and running correctly, and to prevent any
accidental damage or injury, please read and follow the below instructions
carefully before using your product.
SAFETY
IMPORTANT! Disconnect the mains electricity supply before attempting any
installation / maintenance of any kind. Do not attempt to modify this unit in
any way and only use the recommended parts for replacement.
· The PFC unit should never be run dry as this will cause the unit to overheat
and cause permanent damage.
· All connections must be earthed.
· The power cord of this appliance cannot be replaced; if the cord is
damaged, the appliance should be discarded. Never cut the cord.
· Do not connect to any voltage other than that stated.
· Do not place in liquids other than water.
· Do not use with water above 90°F or 30°C.
· Do not carry or pull the unit by its electrical cable.
· Do not use this unit if it has a damaged cord, if it is malfunctioning or it is
dropped or damaged in any manner
· Do not attempt to modify this unit in any way and only use attachments and
the recommended parts for replacement recommended by the
manufacturer.
· Before installing, maintaining or handling your equipment, or before placing
your hands in your pond, ensure that the unit is disconnected from the
electricity supply.
· Always disconnect any electrical devices when not in use.
· Carefully examine your pond system after installation. Do not connect the
unit to the mains if there is water on any parts not intended to be wet.
· Do not look directly at the UV light when it is operational.
· Before operating your unit observe that water is flowing through it - the UV
requires constant flow to avoid overheating.

· To avoid injury, do not touch hot or moving parts such as, but not limited to
UV bulbs or impellers.
· During maintenance ensure all O-rings are present and intact.
· If the appliance shows any signs of water leakage or the RCD unit switches
off, disconnect the unit from the power supply and consult the retailer
where you purchased the unit.
· Do not install or store this unit where it will be exposed to temperatures
near to 0°C / 32°F. In freezing conditions, remove and store the unit in a
sheltered area ensuring all water has been drained from the filter.
· Do not bury the cord for this unit. Ensure it does not cause a trip hazard or it
at risk from damage from lawn mowers, strimmers or other garden
equipment.
· Ensure the PFC is located at least 2 metres from the pond edge.
Please note – this appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental capabilities or lack
of experience and knowledge, provided they are given supervision and
instruction concerning use of the appliance and understand the hazards
involved. Children must not play with the appliance. Any maintenance must not
be made by children without supervision.
OUTLET SYMBOLS
WATER INLET POINT
WATER OUTLET POINT
SELF CLEANING POINT

ELECTRIC
This unit comes complete with a generous supply of 3 core cable, however
should any additional cable be required, the use of an approved waterproof
cable connector with a proper rating is essential. A cord rated for less amperes
or watts than the appliance rating may overheat.
Please Ensure:
· The power supply must be earthed and fused at 3amps.
· You regularly inspect the cable for damage and deterioration.
· Do not connect to any voltage other than that stated.
· You consult a qualified electrician if in doubt about any aspects of
wiring.
· A residential current device (RCD) is used for additional safety
· You have complied with Local Electricity Authority regulations if
permanently installing to the mains supply.
Please Ensure: The power supply must be earthed and fused at 3amps.
Regularly inspect the cable for damage and deterioration. Consult a qualified
electrician if in doubt about any aspects of wiring.
· The pressure of your unit depends on many factors such as location (height
and distance from your pond), power and location of the connected pump
(L/H), pond depth, stock density and hose dimensions. To enhance pond
water quality, we recommend considering these factors to ensure
maximum efficience and avoid low return pressure.
· If positioning your filter above ground, ensure it is located at least 2 metres
from your pond edge. If your filter will be sunk into the ground, you can
position the unit closer to the water.
· Place your filter on a level and sturdy surface that is well ventilated and not
at risk of flooding.
· To avoid overheating, ensure the filter is not covered and is positioned away
from direct sunlight.
· Position the filter so the hosing connected to the Water Inlet Point and
Water Outlet Points is not bent or obstructed.
CHOOSING YOUR FILTER LOCATION

· The filter is suitable for burying up to the head rim of the unit. Make sure
access to the body of the system is possible for maintenance purposes.
Burying the unit will help reduce the distance between the filter and the
pond and provide higher return water pressure.
INSTALLATION & USE
Please read the below instructions carefully before beginning to set up your
filter. DO NOT CONNECT THE UNIT TO THE MAINS UNTIL SET UP IS
COMPLETE AND UNIT IS FILLED WITH WATER.
1. Prior to installing the unit, examine the quartz sleeve and UV bulb to make
sure these have not been damaged in transportation (see maintenance
section). Handle with care. Do not hold UV bulb with bare hands as this can
affect performance.
2. Connect the required attachments - Choose the required hosetails
(dependent on your flexible hose dimensions) and attach to the filter (utilise
nut and o-ring in tandem to seal tight). On stepped hosetails if using a hose
larger than the smallest dimension, you will need to cut down the hosetails to
avoid restricting the flow of water.
3. Position the filter - unless you are burying the unit, ensure that the filter is
placed adjacent to your pond (at least 2 metres away from the water).
4. Connect your flexible hose to the filter - connect your flexible hose to the
hosetails. Safely connect using either jubilee / wire clips to ensure this is water
tight. Your pump (not included) should be attached to the ‘Water Inlet Point’.
The ‘Water Outlet Point’ should direct water either back into your pond or to a
waterfall adjacent to the pond. Ensure the water direction knob is pointed
towards your ‘Water Inlet Point’ and ‘Water Outlet Point’.
5. Connect the filter to the mains - Connect the unit to the mains using a
residual current device (RCD) for additional safety.
6. Switch on your pump - Switch on your pump and visually inspect that you
have the expected water flow through the filter. Visually check that you have
no leakage.
7. Switch on your filter at the mains - now that you have visually checked that
the unit is being supplied with the required flow of water you can turn on the
UV operation by switching on the unit at the mains.

PRODUCT DIAGRAM
F
A
E
H
GI
B
C
D
I
B
C
D
F
A
E
GH
Biological Filtration
Vortex System - centrifugal effect breaks down dirty water
Water Inlet Point - connects to pond pump
Mechanical Filtration
UV Bulb - clarification / sterilisation of water
A
B
C
D
E
Spin Clear Handle - spins and squeezes the filter foams
Spin Clear Point - maintenance and waste drainage
Water Outlet Point - connects to water return
Water Direction Knob - switches between normal and spin clear operation
F
G
H
I

PARTS DIAGRAM
24
25
26
27
1
2
3
4
5
6
7
8
9
12
13
14
15
16
17
10
11
18
19
20
21
22
23 28
UV LAMP
O-RING
UV HEAD COVER
UV SLEEVE
UV O-RING
1
2
3
4
5
UV QUARTZ
UV QUARTZ NUT
6
7
PLATE HOLDER
SPONGES
PFC LID
FILTER PLATE
MEDIA PLATE
8
9
10
11
12
BIO BALLS
MEDIA BASKET
13
14
HANDLE KNOB
MAIN HEAD O-RING
HEAD CLASP
PFC BODY
HANDLE SHAFT
15
16
17
18
19
HANDLE BEARING
HOSETAIL O-RING
20
21
ROD BEARING
OUTLET NUT
HOSETAILS
DISPLAY ROD
ROD WASHER
22
23
24
25
26
ROD SCREW
OUTPUT CONTROL DIAL
27
28

PARTS DIAGRAM PFC-50000
HANDLE SHAFT
O-RING
UV HEAD COVER
HANDLE KNOB
OUTLET NUT
1
2
3
4
5
HOSETAILS
DISPLAY ROD
6
7
ROD BEARING
8
HANDLE BEARING
ROD WASHER
ROD SCREW
HOSETAIL O-RING
9
10
11
12
UV SLEEVE
UV LAMP
13
14
UV QUARTZ
UV O-RING
15
16
PFC LID
UV QUARTZ NUT
SPONGES
17
18
19
FILTER PLATE
PLATE HOLDER
20
21
MAIN HEAD O-RING
HEAD CLASP
MEDIA PLATE
22
23
24
BIO BALLS
MEDIA BASKET
25
26
DIVERTER SCREWS
DIVERTER PLATE
27
28
22
23
24
25
26
27
28
29
30
31
1
2
3
4
5
6
7
8
9
10
11
12
32
13
14
15
16
17
18
19
20
21
INTERNAL CONTAINER
29
K MEDIA
PFC BODY
OUTPUT CONTROL DIAL
30
31
32

UVC OPERATION
· Always ensure that the filter has water flowing through the unit prior to
operating the UV.
· Never look directly at the UV light when operational.
· Check that the UV is operational visually using the UV indicator.
· Never operate the UV lamp outside its housing.
· Never operate the UV lamp in a housing that’s defective.
MAINTENANCE
To ensure optimal performance and that your unit functions correctly, regular
maintenance is essential. Failure to do so may result in damage to your unit and
may invalidate your warranty.
We recommend that a regular cleaning and maintenance schedule is followed
to ensure responsible fishkeeping. Depending on water volume and stocking
levels, regular cleaning of the filter media, foams, and inlet/outlet pipework will
help ensure that the product works efficiently and your pond remains healthy.
For further maintenance guidance, please see the table and additional
information below:
All Pipework Clean & Inspect
Hosing
O-rings
Filter Foams
UV Bulbs
Quartz Sleeve
Other Media
(Bio Balls)
Clean & Inspect
Clean & Inspect
Clean & Inspect
Lubricate & Clean
Clean & Inspect
Replace
Replace as
required (1-2 years)
Replace
Replace after
2 years
1 MONTH 3 MONTHS 6 MONTHS ANNUALLY
Clean & Inspect

Filter Maintenance
In general, it is recommended to disconnect your PFC and clean the pipes and
filter media on a regular basis. Pipework will become blocked with waste and
protein slime over time, so regular cleaning is important for optimal
performance.
The frequency of how often you will need to clean and inspect your unit of
course will depend on a lot of factors like how dirty the water is when you first
start using your all-in-one system, your pond volume and also how many fish
you have. How often you feed your fish and seasonal light levels will also affect
how quickly your pond water gets dirty and will need to be taken into
consideration when planning how often to clean your filter system.
It is recommended that every two weeks you perform the ‘spin clear cleaning’
process to ensure the continued effectiveness of the filter.
Again depending on the above factors you will need to perform a full deep
clean of the included foams and the inside of the filter body 2-3 times per year.
Please note that the part numbers below are displayed as follows:
(1/8) - the first part number is for all models other than the PFC-50000, the
second part number is for the PFC-50000.
1. Switch off your pump and your PFC at the mains - visually inspect that you
have no water flow through the filter.
2. Connect hose to the Spin Clear Point - safely connect using either jubilee /
wire clips to ensure this is water tight.
3. Aim your waste - Place the end of the hose from the Spin Clear Point to a
suitable location in your garden. Point the Outlet Control Dial (28/32) towards
the Spin Clear Point. Switch on your pump and visually inspect that you have the
expected water flow through the filter. Visually check that you have no leakage.
4. Attach the ‘Self Cleaning Handle’ and spin clear - attach the supplied ‘Self
Cleaning Handle’ (18/3) to the top of your PFC. Spin the handle in either
direction to spin and squeeze the waste from your filter foams.
5. Return the filter to normal operation - Point the water direction knob towards
your towards your Water Inlet Point. Visually check that you have no leakage
and that you have the expected water flow through the filter. Switch on the PFC
at the mains.

It is vital that O-rings are regularly inspected and replaced as the rubber
watertight seal will perish over time, which may cause your unit to leak. Before
replacing your o-rings, ensure they are well lubricated to ensure the seal is
kept water tight.
O-rings
Filter Media
The filter media provided with your unit and their positioning within the filter
body are designed to give complete and optimum filtration for your pond.
IMPORTANT! Always use water from your pond to clean your filter sponges and
media. Do not use mains water or any cleaning products to clean your media.
When replacing media in your filter, do not replace more than 50% of your
media at once. This is to ensure that the nitrifying bacteria present in the old
media are able to repopulate in the newly added filter media.
Fine & Coarse Filter
Foams
Bio Balls
Mechanical Filtration
Biological Filtration
Remove small waste
particles from the water.
Create environment for
nitro-bacteria to cultivate
and help oxygenate the water.
All internal cleaning should be done using pond water.
1. Remove the PFC lid - unfasten the head clasp and remove it. Pull the PFC
lid clear of the PFC and place upside down on a flat surface.
2. Remove the filter sponges - unscrew parts 10, 11/20 and 21. You can now
remove the filter sponges from your unit.
3. Clean your filter sponges - clean the filter sponges and replace. Reattach
the parts 10, 11/20 and 21.
4. Clean biomechanical media - rinse throuh your Bio Balls and K media in
the bottom of the filter body.
5. Clean body and all attachments - reassemble.
Deep Clean Maintenance

SPECIFICATIONS
MODEL
UV POWER (WATTAGE)
DIMENSIONS (LxWxH) (mm)
FILTER BODY VOLUME (L)
MAX FLOW RATE (L)
HOSETAIL FITS
CABLE LENGTH
VOLTAGE
SUITABLE FOR PONDS WITH
NO FISH (DECORATIVE)
SMALL MIX OF FISH
HEAVY STOCKED KOI
PFC-5000 PFC-8000 PFC-12000 PFC-20000
11w
310x310x405mm
16L
6000
20, 25 & 32mm
5m (plug not included)
220 - 240v / 50Hz
11w
380x380x400mm
20L
9000
11w
380x380x510mm
25L
10000
18w
380x380x740mm
38L
10000
<5000L
<3000L
<1500L
<8000L
<5000L
<4000L
<12000L
<9000L
<6000L
<20000L
<12000L
<10000L
20, 25, 32 & 38mm
MODEL
UV POWER (WATTAGE)
DIMENSIONS (LxWxH) (mm)
FILTER BODY VOLUME (L)
MAX FLOW RATE (L)
HOSETAIL FITS
CABLE LENGTH
VOLTAGE
SUITABLE FOR PONDS WITH
NO FISH (DECORATIVE)
SMALL MIX OF FISH
HEAVY STOCKED KOI
PFC-25000 PFC-30000 PFC-50000
36w
450x450x550mm
50L
12000
32, 38 & 50mm
5m (plug not included)
220 - 240v / 50Hz
55w
450x450x715mm
75L
12000
55w
600x600x815mm
170L
13000
<25000L
<20000L
<15000L
<30000L
<25000L
<20000L
<50000L
<35000L
<28000L

TROUBLESHOOTING
UV Indicator is not Lighting Up
If the UV indicator on the top of the filter lid is not lighting up follow these
troubleshooting steps:
1. If you find that the UV light is not operational, check that you have power
from the mains supply.
3. If you do have power from the mains supply, clean the UV indicator. Check if
you can see the UV is operational through the viewing hole on top of the unit. If
you aren’t able to see it, try performing a safety override. Locate the safety
override switch on the ballast end next to the UV bulb fitting (the switch is a
small piece of metal attached to the ballast).
IMPORTANT! NEVER look directly at the UV light. Press and hold the small thin
silver switch when the power is on and the bulb should ignite. Please test in a
dark/ shadowed place and do not look directly at the bulb – we recommend
covering the bulb with kitchen roll or similar. You should still be able to see the
glow of the bulb through this.
4. If the above does not solve the issue replace the UV bulb.
5. Please check for signs of damage or water ingress to quartz sleeve and bulb
area. You might need to replace your quartz sleeve and/or O-Ring if that’s the
case.
6. If you find that the UV light is still not operational after the bulb replacement,
the UV ballast may have developed a fault and you will need to contact the
supplier of your unit to obtain replacement parts.
Please remember that UV bulbs for use in ponds should be replaced every 12
months.
Slow Flow Rate
1. Rinse unit’s foams making sure they are free of debris.
2. Ensure that the inlet hose connecter has been cut correctly to size, if not
this will restrict the flow from the pump into the filter.
3. Ensure that the inlet hose is not kinked or crushed.

The UV Bulb is on But My Pond is Green
There are a lot of different factors which contribute to this type of issue and it
may not be the UV system at fault. The UV clarifier will work to maintain rather
than transform water quality so you may need to add treatments to clear poor
quality water or consider a heavy water change.
Algae growth in water can be due to high phosphate and nitrate and green
water is heightened in the summer period due to the extra sunlight so it is also
advised that a water test is carried out.
If the UV light is working then the product is functioning correctly. The position
of the pond should also be considered, as this affects how much sunlight is
directly falling on the pond. Algae growth is very likely to require a treatment to
resolve the growth. Consider purchasing the All Pond Solutions Green Water
treatment or Blanketweed treatment.
The orientation of the garden can also be an issue; south facing gardens
inevitably get more sunlight and can cause ponds to be greener in the
summer if exposed all day. Try and shade your pond water surface, plants are a
great way to do this.
My Pond Water is Cloudy/Brown
1. Make sure the unit is turned on 24 hours a day. Continuous running is
needed to maintain a clean and healthy pond.
2. Remove pond waste and leaves and carry out a partial water change. If
sludge is present treat your pond with All Pond Solutions Anti Sludge
treatment.
In order to correctly identify if you have green water or cloudy/brown water, a
settlement test should be carried out.
Take a jar of pond water and allow to settle for 24 hours.
Green Tinge - If your jar is showing mostly green tinged water or has green
particles floating in it, you most likely have a bit of an algae problem (follow
the green water trouble shooting guide).
Brown Tinge / Water with Sediments - this indicates that you have organic
debris decomposing in your pond. This can be particles from dead leaves,
twigs and other plant debris that are breaking down (follow the brown water
trouble shooting guide).
Green Water or Cloudy/Brown Water?

3. Reduce feeding. Overfeeding introduces a lot of organic waste and is one of
the main causes for cloudy water problems.
4. Make sure to perform regular water changes, check your unit is clean and
adequate for your pond size and do not overstock it.
My Unit is Cutting Out
1. Rinse unit’s foams making sure they are free of debris.
2. Inspect the quartz sleeve for hair line cracks and ensure that all O-rings are
in place and well lubricated.
If none of the above resolves your issue, or you require spare parts for your
filter, please contact the supplier of your unit.
My filter is leaking
1. Check that the inlet/outlet caps and O-ring have been correctly assembled
and that they are hand tight. Ensure the O-rings are intact, well lubricated and
not twisted or damaged.
2. Always secure the inlet hose and outlet hose with a jubilee clip.
3. If you find that the unit is still leaking after the above checks or there is an
obvious casing crack, you will need to replace the body casing on the unit.

The All Pond Solutions PFC range is guaranteed against defects in material or
workmanship under normal pond usage and comes with 24 months warranty for
all electrical parts. The warranty period commences from the date of purchase.
If you require support on how to use your unit, replacement parts or if your filter
develops a fault during the warranty period, please contact the supplier of your
unit.
Non-replaceable, non-perishable and non-serviceable parts will be repaired or
replaced free of charge, once the unit is returned with all components along
with a valid proof of purchase and postage paid. We reserve the right to replace
or repair the unit at our discretion.
Please be aware that perishable parts that are subject to normal wear and tear,
such as impellers, impeller covers, motor seals and UV bulbs, are not covered
by your warranty and a charge may be required for replacements of these.
This warranty does not apply to any unit that has been subjected to misuse,
accidental damage, negligence, tampering or customisation. It does not apply
to units which have been assembled incorrectly, improperly maintained, or
where the instructions and safety information in this manual has not been
followed correctly.
No liability is assumed with respect to loss or damage to livestock or personal
property irrespective of the cause thereof.
Please ensure that only genuine All Pond Solutions components are used when
completing a replacement or repair. Spare parts are available at our official
website or from your local supplier.
Before returning your unit under warranty terms, check that all setup and
maintenance instructions have been correctly followed. If you are in doubt,
please contact your local aquatic retailer for further advice before returning the
product.
This does not affect your statutory rights.
WARRANTY