ALL WEATHER 8100 Series User manual

777 Aldridge Road | Vacaville, CA 95688 | 800.680.5800 | www.allweatheraa.com
INSTALLATION INSTRUCTIONS
SERIES 8100 | MULTI SLIDE DOOR SYSTEM

777 Aldridge Road | Vacaville, CA 95688 | 800.680.5800 | www.allweatheraa.com
SERIES 8100 IMULTI SLIDE DOOR SYSTEM
INSTALLATION INSTRUCTIONS
2
INSTALLATION QUALITY CONTROL
Performing specific quality control procedures is a critical part of completing any All Weather installation. We recommend the
installer fill out the quality control sheet and file as a record of correct and complete installation.
Customer: Phone:
Address:
Installer: Phone:
Where product was purchased:
Dealer Contact:
RECEIVING AND INSPECTING OF PRODUCT
Product was checked upon delivery at job site for correctness and was received as ordered
Product was checked and free of damage
Any damage or incorrectness was reported immediately to All Weather or the dealer where the product was purchased
Product was stored in a dry safe place where it could avoid damage
Hardware box contents were checked
PRE-INSTALLATION
General Contractor or homeowner has been consulted prior to installation of product
Opening is configured correctly, and any squaring or level issues have been identified
Appropriate size header has been verified for use in opening
If applicable, sill pan with Rear Leg (Back Dam) has been fabricated from appropriate material and locates correctly in the
depth of the rough opening
Overhangs and other necessary design elements are present where appropriate
Local codes and practices are being adhered to regarding installation of product
Problems pertaining to existing windows, doors and/or rough openings have been reported to responsible party and have been
resolved and documented
All safety issues related to unsafe site conditions and hazardous materials have been properly addressed and resolved

777 Aldridge Road | Vacaville, CA 95688 | 800.680.5800 | www.allweatheraa.com
SERIES 8100 IMULTI SLIDE DOOR SYSTEM
INSTALLATION INSTRUCTIONS
3
INSTALLATION
All installation materials used have been checked for compatibility
Weather resistant barrier and flashing were coordinated with contractor or authority on site
If Swing Series, correct orientation of system has been identified. Inswing or Outswing.
If Slider Series (including Stacking and Pocketing Series), location of operable and non-operable panels has been checked
If Bi-Fold Series, panel sequence has been checked from right to left, as seen from exterior
Frame has been sealed and joined at all points indicated in instructions
Opening checked for correct dimensions
Frame is installed at correct depth within the opening
Frame has been installed square, level and plumb
Plastic shims were utilized under sill when required
Jambs were shimmed to prevent rolling
Head track installed with the appropriate crown over width of frame
Installation holes prepared correctly
Sealant was applied to sill installation holes prior to inserting screws & top of screw heads once applied
Correct fastener placement has been followed as directed by manufacturer
Proper operation and adjustment has been achieved
Product was installed as directed by the Manufacturer
FINAL CHECK OF INSTALLATION
Frame has been checked for level, square and plumb
All horizontal and vertical adjustments have been made so that proper reveals are present and product is operating as
designed
Weep holes have been checked and free of obstruction and debris
All trash has been discarded
All hardware has been installed correctly and checked for proper operation
Product has been closed and locked and recommended to not be used as thoroughfare by other trades.
Product is protected from damage
Final inspection of weather proofing and operation has been performed
Job has been turned over to contractor or other responsible party with approval
Other
IMPORTANT
All Weather recommends that installers return to site and perform a final check of installation. Namely that the header has
not sagged under structure settlement and/or weight and necessary adjustments have been made prior to installation of exterior
siding/stucco and interior finishes.
Where applicable, each of the items checked above have been properly reviewed, verified and completed as part of my field
quality control check prior to turning over the job to the responsible party/approving authority.
Installer’s Signature: Date:

777 Aldridge Road | Vacaville, CA 95688 | 800.680.5800 | www.allweatheraa.com
SERIES 8100 IMULTI SLIDE DOOR SYSTEM
INSTALLATION INSTRUCTIONS
4
THANK YOU FOR PURCHASING FROM ALL WEATHER.
ALL WEATHER INSTALLATION AND WARRANTY INFORMATION
The following instructions are to be used for All Weather assembly and installation.
Limited warranty varies based on job type. A copy of the limited warranty and the comprehensive care and maintenance guide can
be found at www.allweatheraa.com.
Failure to follow factory assembly, installation and maintenance instructions will void the manufacturer’s limited warranty. All
visible defects must be reported before installation and finishing.
These instructions are the property of All Weather Architectural Aluminum and may not be duplicated, altered or distributed for
any purpose whatsoever without the express written permission of All Weather.

777 Aldridge Road | Vacaville, CA 95688 | 800.680.5800 | www.allweatheraa.com
SERIES 8100 IMULTI SLIDE DOOR SYSTEM
INSTALLATION INSTRUCTIONS
5
THE MOST IMPORTANT CRITERIA FOR A SUCCESSFUL JOB ARE A SQUARE OPENING,
A RIGID HEAD AND A CLEAN TRACK.
It is recommended that All Weather doors are installed with at least two people; one person handling the door panels and the
other attaching and adjusting hardware.
The installation of your door system requires that the sill, head and jambs are perfectly straight and square. It is recommended
that the head be installed with a slight bow upward (amount specified in installation instructions). The sill should be installed flat
and straight, ensuring that there is no upward bowing. The frame should be checked for square and twist.
Assembly screws are provided by All Weather. Be sure to clean any metal shavings from the head track to avoid damage to the
rollers.
Ensuring your frame is square, plumb, and attached properly to an adequate header will alleviate problems in the future.
Installation of flashing to ensure a proper water seal is the responsibility of the installer. Local codes and building practices
should be applied.
All Weather doors require sill pans with rear leg (back dam) and recommends Consultation with a water proofing consultant for
an adequate drainage system.
*IMPORTANT NOTICE* – READ PRIOR TO INSTALLATION.
An All Weather system is a specialty product that you cannot assume to be a standard installation of a typical door or
window.
All Weather products should be installed with overhead protection to prevent the effects of sheeting water from above.
We recommend that a professional waterproofing consultant be used to properly integrate our products into the weather
barrier of the wall structure.

777 Aldridge Road | Vacaville, CA 95688 | 800.680.5800 | www.allweatheraa.com
SERIES 8100 IMULTI SLIDE DOOR SYSTEM
INSTALLATION INSTRUCTIONS
6
PROVIDED ASSEMBLY FASTENERS & PARTS
PART PICTURE DESCRIPTION PURPOSE
1
#10-12 x 3" Square Drive Pan
Head Grade 18-8
Type A Point Stainless Steel
Sheet Metal Screw
To secure the keeper onto the
door jamb and building frame
through 4 slotted holes.
2
#8-15 x 1-½" Square Drive
Pan Head Grade 18-8
Type A Point Stainless Steel
Sheet Metal Screw
To fasten the door frame
components together.
8 per track will be needed.
3
#10-16 x 1" Square Flat Head
Crypton Finish 410 Stainless
Steel Self-Drilling Screw
To fasten the fixed panels t
o the frame and to install
false jambs.
4
#8 x ³⁄ 88 " Square Drive Pan
Head #2 Point 410 Stainless
Steel Self-Drilling Screw
To fasten the nail-fin to the
head and jambs of the frame.
5*
#10 x ¾" Square Drive Flat
Head 410 SS Self-Drilling
Screw (*for panel collector
option or staggered tracks)
To fasten panel collectors to
intermediate panels, to fasten
track end caps to track faces.
6.18" x 12" Black Rigid PVC
Track Clip
To connect multiple Head,
Sill, and Jamb Assemblies
together via the Frame
connecting grooves.
73mm x 30mm Spring Roll Pin
For splicing: to connect
multiple head and sill
Assemblies together
via screw holes.
8Black PLA Roller Track
Connector
For splicing: to connect
multiple Head and Sill
assemblies together via the
frame roller track grooves.
9Aluminum Splicing Plate
(sheet metal)
For splicing: to reinforce
splice joint
10 Nail-Fin Corner Adapter
To connect the nail fins on the
jambs to the nail-fin on the
head to allow for a better seal
on the exterior corners.

777 Aldridge Road | Vacaville, CA 95688 | 800.680.5800 | www.allweatheraa.com
SERIES 8100 IMULTI SLIDE DOOR SYSTEM
INSTALLATION INSTRUCTIONS
7
PROVIDED ASSEMBLY FASTENERS & PARTS
PART PICTURE DESCRIPTION PURPOSE
11A Head Nail-Fin
To attach the frame to the
rough opening of the building
on the top.
11B Left Jamb Nail-Fin
(Top end shown in diagram)
To attach the frame to the
rough opening of the building
on the left side.
11C Right Jamb Nail-Fin
(Top end shown in diagram)
To attach the frame to the
rough opening of the building
on the right side.
12 Head Track To guide sliding door, top
member of door frame.
13 Jamb Track
Frame member. To collect
panels and provide a seal
for panels when in the
closed position. The keeper
will be mounted on the
inside of the jamb.
14A Sill Track
Frame sill member. To provide
a weight bearing member
and track for the panel rollers
to travel on.
14B Flush Set Sill Track
Frame sill member option.
To provide a weight bearing
member and track for rollers
to travel on. Designed to sit
flush with flooring.
15 Keeper
To provide the panel hooks on
panels channels to lock into to
keep the panel secured into
the frame.

777 Aldridge Road | Vacaville, CA 95688 | 800.680.5800 | www.allweatheraa.com
SERIES 8100 IMULTI SLIDE DOOR SYSTEM
INSTALLATION INSTRUCTIONS
8
PROVIDED ASSEMBLY FASTENERS & PARTS
PART PICTURE DESCRIPTION PURPOSE
16 1.8" x 1.6" Trim Cap
To cover and protect the track
pockets on the Jambs that will
not be used by the panels.
17 .4" x .6" Threshold
To cover and protect the track
pockets on the sills that will
not be used by the panels.
18* Panel Collector
(*optional add-on)
Designed to not allow panels
to bypass one another while
opening sliding doors.
19*
Head Track End Cap
(*for staggered track doors
only)
Designed for aesthetic
purposes to cover the
exposed head track faces in
the location the staggered
tracks terminate.
20*
Sill Track End Cap
(*for staggered track doors
only)
Designed for aesthetic
purposes to cover the
exposed sill track faces
in the location the staggered
tracks terminate.
21A Pull Handle Keyed
To provide a way to open
and close a panel easily that
also allows for the panels to
be locked/unlocked by a key.
The latches can be engaged/
disengaged by rotating the
thumbturn.
21B Pull Handle with Thumbturn
To provide a way to open
and close a panel easily. The
latches can be engaged/
disengaged by rotating the
thumbturn.
21C Dummy Pull Handle To provide a way to open and
close a panel easily.
22
#6-20 x ³⁄ 88 " Phillips Drive Flat
Head Zinc Finish #2 Point
Steel Self-Drilling Screw
For splicing: to fasten splicing
sheet metal plates to head
and sill tracks.

Track Clips Part #6
Sill Part #14a
Flush Set Sill Part #14b Notch for the nail-fin goes toward the exterior
Notch for the nail-fin goes toward the exterior
777 Aldridge Road | Vacaville, CA 95688 | 800.680.5800 | www.allweatheraa.com
SERIES 8100 IMULTI SLIDE DOOR SYSTEM
INSTALLATION INSTRUCTIONS
9
Note: Opening should be flashed with the appropriate flashing material to meet industry standards. Please refer to Federal
Specification UU-B-790a and AAMA 2400-02.
Disclaimer: Each installation job has its unique set of challenges and circumstances. Because of that, the provided set of
installation instructions for All Weather Architectural Aluminum products is meant only to serve as a set of standardized
guidelines and NOT necessarily a strict manual to follow regardless of situation.
As a professional, it is incumbent upon you and your team to identify instances that do not align with the Installation instruction
requirements. All installations must comply with AAMA specifications.
Accordingly, All Weather does not assume responsibility, and disclaims liability for damage, loss, or expense arising from
improper use or application of these installation instructions.
FRAME ASSEMBLY/INSTALLATION
1. Verify that the rough opening is the correct size to assure the door will fit in the opening.
2. Check to ensure that the floor where the door will be installed is level. If the floor is not level and varies more than ¹⁄ 1616 " per
foot or a total of ¼" over the entire width of the opening, correct the floor prior to installation.
3. Remove the frame components from its packaging and lay it out in front of the opening. Note that the notches for a nail-fin
goes toward the exterior (Figures 1 & 2).
4. For doors with multiple tracks, attach adjacent heads, jambs, and sills (Part #12, #13 #14a/b) using track clips (Part #6).
Figures 1 & 2 from step 3 show the junction of standard and flush set sills via track clips. Track clips can be pressed or
hammered into place
FIGURE 1
FIGURE 2

Splicing Plate Part #9
Roll Pin Part#7 (x4)
Track Connector Part #8
*Sealant required on
connector*
Splicing Plate Part #9
Sill Part #14a
Screws Part #22
Roll Pin Part#7 (x4)
Track Clip Part #6
Head Part #12
Screws Part #22
Sealant
Sealant
Splicing Plate Part #9
Roll Pin Part#7 (x4)
Track Connector Part #8
*Sealant required on
connector*
Splicing Plate Part #9
Sill Part #14a
Screws Part #22
Roll Pin Part#7 (x4)
Track Clip Part #6
Head Part #12
Screws Part #22
Sealant
Sealant
777 Aldridge Road | Vacaville, CA 95688 | 800.680.5800 | www.allweatheraa.com
SERIES 8100 IMULTI SLIDE DOOR SYSTEM
INSTALLATION INSTRUCTIONS
10
1. Splicing is required for doors wider than extrusion stock length. To splice the sill (and Flush Set Sill), insert roll pins
(Part #7) halfway into screw channels as shown in Figure 1. Coat track connectors (Part #8) in sealant (Sealant should
conform to AAMA 802.3-16 and 803.3-16) and slide halfway into the roller track. Coat the entire cross-sectional face with
sealant as shown in Figure 2 and join the components by tapping one track into the other. Lastly, fasten Splicing Plate
(Part #9) over the junction using (Part #22) screws. Screw in the location of the thermal dividers (shown in Figure 2).
Splicing plate is not required for a flush set sill. Before screwing the plate to the sill, use a ³⁄ 88 " countersink bit to create
countersinks for the top of the flat head screws to sit flush with the plate.
2. To splice the head (Figure 1), insert roll pins (Part #7) into the head screw channels. Coat the entire cross section in sealant
as shown in Figure 2, join components, and ensure track clip (Part #6) crosses over the splice (if multiple track door). Lastly,
attach splicing plate (Part #9) over the junction using (Part #22) screws at the thermal breaks. Countersink the plate for the
screws beforehand.
FIGURE 1
FIGURE 2
FIGURE 1
FIGURE 2

Jamb Part #13
Screws Part #2
Screws Part #2
Screws Part #2
Sill Part #14a, 14b
for Flush Set Sill
*Continuous Bead of Sealant* HeadNail-Fin Part #11a
Left Jamb Nail-Fin
Part #11b
Note: Remove Trim Caps (Part #16)
from head andjamb tracks before
assembling frame
Head Part #12
Sealant
Jamb Part #13
Screws Part #2
Screws Part #2
Screws Part #2
Sill Part #14a, 14b
for Flush Set Sill
*Continuous Bead of Sealant* HeadNail-Fin Part #11a
Left Jamb Nail-Fin
Part #11b
Note: Remove Trim Caps (Part #16)
from head andjamb tracks before
assembling frame
Head Part #12
Sealant
777 Aldridge Road | Vacaville, CA 95688 | 800.680.5800 | www.allweatheraa.com
SERIES 8100 IMULTI SLIDE DOOR SYSTEM
INSTALLATION INSTRUCTIONS
11
3. It is recommended to remove the pre-installed trim caps (Part #16) from head and jamb tracks before assembling the frame.
Prepare frame by applying compatible sealant around the perimeter of both ends of the frame head (Part #12) and sill (Part
#14a, 14b for Flush Set Sill). Use the screws (Part #2) provided in the hardware box (Use sealant to lubricate screws) and
assemble the frame as shown in Figures 1, 2, & 3.
4. Next, connect the head nail-fin (Part #11a) to the head of the frame (head nail-fin does not have shaved hooks). To do this,
first apply a continuous bead of sealant to the nail-fin in the pocket it will contact the head (Figure 1). The head nail-fin should
extend slightly beyond the head track on either side and fit into the pocket created by the jambs (Figure 2). Pre-drilled holes
should line up on the head and head nail-fin.
FIGURE 1
FIGURE 1
FIGURE 2
FIGURE 2
FIGURE 3

Screws Part #4
Screws Part #4
Head Part #12
Jamb Part #13
Note: Line up pre-drilled holes
on nail-fins and head/jambs
Verify
Square
C
D
BA
Screws Part #4
Screws Part #4
Head Part #12
Jamb Part #13
Note: Line up pre-drilled holes
on nail-fins and head/jambs
Verify
Square
C
D
BA
777 Aldridge Road | Vacaville, CA 95688 | 800.680.5800 | www.allweatheraa.com
SERIES 8100 IMULTI SLIDE DOOR SYSTEM
INSTALLATION INSTRUCTIONS
12
5. Fasten the head nail-fin using screws (Part #4) as shown in Figure 1. Screw at the locations of the pre-drilled holes. Repeat
process for left and right jamb nail-fins. Note left and right nail-fins must be on correct sides to fit on the frame properly.
6. Prepare rough opening by checking diagonal dimension of opening to verify square and apply water resistant barrier as shown
in Figure 1. Use steps A through D for applying water resistant barrier.
A. 12" Sill Wrap (3" wrapped into opening); Overlaps where sill Self-Adhering Sheet Membrane (SASM) will be by 1"
(Self-adhered flashing is optional)
B. 12" Jamb SASM (3" wrapped into opening), overlaps Sill SASM by 1" and runs 2" beyond header opening
C. 6" Header Wrap (3" wrapped into opening), overlaps jamb SASM by 1"
D. Sill pan is recommended on all door installs, with the exception of frames with a flush set sill (Part #14b). Consult step 15
for details on securing the sill pan to the opening.
FIGURE 1
FIGURE 1

Nail-FinCorner Adapter
Part #10
Left Jamb Nail-Fin Part #11b
HeadNail-Fin Part #11a
Nail-FinCorner Adapter
Part #10
Left Jamb Nail-Fin Part #11b
HeadNail-Fin Part #11a
777 Aldridge Road | Vacaville, CA 95688 | 800.680.5800 | www.allweatheraa.com
SERIES 8100 IMULTI SLIDE DOOR SYSTEM
INSTALLATION INSTRUCTIONS
13
7. Clean the exterior of the frame (including the nail-fin) with a moist rag (wetted with water) so that the frame and nail-fin are
free from dirt and other construction debris and dry it with a dry clean rag or allow it to air dry.
8. Make sure that each corner joint of the frame has sufficient sealant. Apply sealant to the corner joints as necessary to ensure
a watertight seal as shown in Figure 1.
9. Apply sealant to the backside of the 2 Nail-Fin Corner Adapters (Part #10) and install the brackets at upper corners of the
frame as shown in Figure 1.
FIGURE 1
FIGURE 1

Bead of Sealant
(continuous) Sealant
777 Aldridge Road | Vacaville, CA 95688 | 800.680.5800 | www.allweatheraa.com
SERIES 8100 IMULTI SLIDE DOOR SYSTEM
INSTALLATION INSTRUCTIONS
14
10. Apply a continuous bead of sealant on the nail-fins (Part #11a, 11b, 11c, interior side as shown in Figure 1) around the
perimeter of the head (Part #12) and jambs (Part #13) of the frame as shown in Figure 2, including the nail-fin corner adapter
(Part #10). Sealant should conform to AAMA 802.3-16 and 803.3-16.
FIGURE 1 FIGURE 2

Sealant (beads)
Sill pan
Sealant (continuous),
plastic shims as needed
Sealant (continuous)
Weep Channels
Sill Part #14a
777 Aldridge Road | Vacaville, CA 95688 | 800.680.5800 | www.allweatheraa.com
SERIES 8100 IMULTI SLIDE DOOR SYSTEM
INSTALLATION INSTRUCTIONS
15
11. For frames with a standard sill (Part # 14a), use step 15 for installing frame. For a flush set sill installation (Part #14b), consult
step 16. Apply several continuous beads of sealant across the bottom of the sill pan (enough to cover the entire contact area
between sill pan and opening), and shim as needed under the sill pan to ensure level. Insert sill pan into the opening. Next,
apply beads of sealant to the underside of the frame’s sill, incrementally spaced between the weep channels as shown in
Figures 1 & 2. (Sealant should conform to AAMA 802.3-16 and 803.3-16). Insert the frame into the opening as shown in
Figures 2 & 3. Manipulate frame to achieve proper alignment. Shim around jambs and head, as necessary. Make sure the
exterior and weeps are not covered with sealant to allow water in the tracks to weep out. After frame is installed, seal all four
corners with sealant as shown in Figure 3.
FIGURE 1
FIGURE 2
FIGURE 3

Head Part #12
Install
Screw
Install
Screw
Install
Screw
B
B
A
A
A
A
A
B
B
A
A
A
A
A
B A A A A A A A A B
Jamb Part #13
Shims
Slab/Subfloor
Install Screws Flush Set Sill Part #14b
Shim as needed
Head Part #12
Install
Screw
Install
Screw
Install
Screw
B
B
A
A
A
A
A
B
B
A
A
A
A
A
B A A A A A A A A B
Jamb Part #13
Shims
Slab/Subfloor
Install Screws Flush Set Sill Part #14b
Shim as needed
777 Aldridge Road | Vacaville, CA 95688 | 800.680.5800 | www.allweatheraa.com
SERIES 8100 IMULTI SLIDE DOOR SYSTEM
INSTALLATION INSTRUCTIONS
16
12. For a frame with flush set sill (Part#14b), a sill pan/sealant is not necessary under the sill. Insert frame into the rough opening
and shim as needed under the flush set sill to ensure level as shown in Figure 1. Install screws where there are shims. After
the frame is installed, seal all four corners with sealant as shown in Figure 2.
13. Secure door frame to the opening using appropriate fasteners. Install screws on the linear fin indicator as shown in Figure 1;
spacing to be as shown in Figure 2 where A = 12" and B = 3". Cross measure and use shims as necessary to adjust the door
frame so that the door frame is plumb, level and square. Seal all fasteners with compatible sealant.
FIGURE 1
FIGURE 2
FIGURE 1
FIGURE 2

Flush Set Sill Fixed
Panel Holder
Sill Part #14a
StandardSill FixedPanel Holders Bottom of Fixed Panel
Backer rod
w/ Sealant
Backer rod
w/ Sealant
Backer rod
w/ Sealant
Flush Set Sill Fixed
Panel Holder
Sill Part #14a
StandardSill FixedPanel Holders Bottom of Fixed Panel
Backer rod
w/ Sealant
Backer rod
w/ Sealant
Backer rod
w/ Sealant
777 Aldridge Road | Vacaville, CA 95688 | 800.680.5800 | www.allweatheraa.com
SERIES 8100 IMULTI SLIDE DOOR SYSTEM
INSTALLATION INSTRUCTIONS
17
14. Apply backer rod and compatible sealant to the interior joint between the frame and the rough opening as shown in
Figures 1 & 2.
PANEL INSTALLATION
Before installing panels, make sure the fixed panel holders are in the right place. Note that standard and flush set sills
(Part #14a, 14b) have different fixed panel holders. For a standard sill, the fixed panel holders should be in the sill prior to
panel installation (Figure 1). For a flush set sill, the fixed panel holder should be attached to the bottom of the fixed panel first,
to be installed later with the panel (Figure 2).
FIGURE 1
FIGURE 1 FIGURE 2
FIGURE 2

Locking Panel
Additional
Rolling Panel
Adjustment
Screw
OXXO OXX/XXO
Locking Panel
Additional
Rolling Panel
Adjustment
Screw
OXXO OXX/XXO
777 Aldridge Road | Vacaville, CA 95688 | 800.680.5800 | www.allweatheraa.com
SERIES 8100 IMULTI SLIDE DOOR SYSTEM
INSTALLATION INSTRUCTIONS
18
15. Install the sliding panel into the interior frame track. You may use a putty knife or similar thereof to help lift the rollers over
the tracks. If you have a staggered track door, you will need to temporarily remove the head and sill track end caps (Part #19,
#20) to avoid clearance issues. For info on removing and installing staggered track end caps, consult Appendix A. If installing
an OXXO door, install both sliding panels on the interior track. If installing an OXX or XXO door, install the locking panel to the
interior track and the additional rolling panel in the center track as shown in Figures 1 and 2.
16. Temporarily adjust the panel upward by lifting the panel and turning the adjustment screw shown in Figure 1 clockwise as
shown in Figure 2 until the rollers regain contact with the track. It is important to physically lift the panel while adjusting
upward so that the adjustment screw does not strip due to the weight of the panel. Adjust the rollers of the active panels by
turning the adjustment screw shown in Figure 1 to achieve proper alignment of the door panels (it is easier to adjust down
than up). Turn screw clockwise to raise the panel and counterclockwise to lower the panel as shown in Figure 2.
FIGURE 1
FIGURE 1
FIGURE 2
FIGURE 2

Screws Part #3
Lockset Hooks
Keeper Part #15
Mark Location, Pre-Drill, Fasten
to Jamb with Screws Part #1
Mark Location, Pre-Drill, Fasten
to Jamb with Screws Part #1
Jamb Part #13
Fixed Panel
Adjustment
Screw
24"
24"
Screws Part #3
Lockset Hooks
Keeper Part #15
Mark Location, Pre-Drill, Fasten
to Jamb with Screws Part #1
Mark Location, Pre-Drill, Fasten
to Jamb with Screws Part #1
Jamb Part #13
Fixed Panel
Adjustment
Screw
24"
24"
777 Aldridge Road | Vacaville, CA 95688 | 800.680.5800 | www.allweatheraa.com
SERIES 8100 IMULTI SLIDE DOOR SYSTEM
INSTALLATION INSTRUCTIONS
19
17. Install the fixed panel into the exterior jamb track (Part #13). Secure fixed panel to the frame with the 2 screws (Part #3)
provided in the hardware box (use sealant to lubricate screws). Screw through the pre-drilled holes in the center weather strip
track of the jamb at 24" above the sill and 24" below the head as shown in Figures 1 & 2.
KEEPER INSTALLATION
18. After the final roller adjustments, install the keeper(s) (Part #15) into the lock side jamb (Part #13) by aligning with the lockset
hooks on the panel and marking the location of the keeper’s four screw holes onto the jamb. Next, pre-drill holes in the jamb
at the marked locations using a ¹⁄ 88 " - ³⁄ 1616 " drill bit. Lastly, fasten the keeper to the jamb with screws (Part #1) as shown in
Figure 1 (use sealant to lubricate screws). After the keeper has been installed, adjust the throw on the hooks of the lockset to
ensure a tight fit when the door is closed and locked by turning the adjustment screw located between the hooks shown in
Figure 2.
FIGURE 1
FIGURE 1
FIGURE 2
FIGURE 2

Trim Cap Part #16
Trim Cap Part #16
Threshold Part #17
Trim Cap Part #16
Interior
Exterior
Interior
Interior
Exterior
Exterior
Jamb Track
Part #13
Jamb Track
Part #13
Exterior sill
track Part#14a
Headtrack Part #12
Trim Cap Part #16
Trim Cap Part #16
Threshold Part #17
Trim Cap Part #16
Interior
Exterior
Interior
Interior
Exterior
Exterior
Jamb Track
Part #13
Jamb Track
Part #13
Exterior sill
track Part#14a
Headtrack Part #12
777 Aldridge Road | Vacaville, CA 95688 | 800.680.5800 | www.allweatheraa.com
SERIES 8100 IMULTI SLIDE DOOR SYSTEM
INSTALLATION INSTRUCTIONS
20
TRIM CAP AND THRESHOLD RE-INSTALLATION
FOR OX, XO, OXO, AND XOX DOORS FOLLOW STEPS 19-20.
19. Take the longest trim cap pieces (Part #16) and install into the exterior jamb track (Part #13) of the operable side shown in
Figure 1 and interior jamb track of the fixed side as shown in Figure 2.
20. Install the threshold (Part #17) into the exterior sill track (Part #14a) and install the smallest trim cap (Part #16) into the head
exterior track (Part #12) shown in Figures 1 & 2
FIGURE 1
FIGURE 1
FIGURE 2
FIGURE 2