ALLDATA S3000 User manual

REMOVAL PROCEDURE
1. Disconnect the negative battery cable.
2. Remove the left fender upper brace.
Fuse Block |Service and Repair, Procedures: Underhood Electrical Center... http://repair.alldata.com/alldata/article/displa .action?componentId=117...
1 of 10 6/10/2013 5:10 PM

3. Remove the electrical center brace cover assemble by lifting the cover (3) outwards to clear the tabs.
4. Remove all fuses and relays.
Fuse Block |Service and Repair, Procedures: Underhood Electrical Center... http://repair.alldata.com/alldata/article/displa .action?componentId=117...
2 of 10 6/10/2013 5:10 PM

. Push on the tab (3) 0 that the electrical center can be rotated on the studs located at (2).
6. Remove all connectors by removing the bolt (1) for each connector.
7. Disconnect all connectors from the electrical center block.
Fuse Block |Service and Repair, Procedures: Underhood Electrical Center... http://repair.alldata.com/alldata/article/displa .action?componentId=117...
3 of 10 6/10/2013 5:10 PM

8. Push on the tabs (2) in order to lift the electrical center (1) out of the housing.
Fuse Block |Service and Repair, Procedures: Underhood Electrical Center... http://repair.alldata.com/alldata/article/displa .action?componentId=117...
4 of 10 6/10/2013 5:10 PM

9. To replace the engine electrical center bracket remove the 4 retaining bolts (1).
10. Remove the engine electrical center bracket assembly from the fender.
INSTALLATION PROCEDURE
Fuse Block |Service and Repair, Procedures: Underhood Electrical Center... http://repair.alldata.com/alldata/article/displa .action?componentId=117...
5 of 10 6/10/2013 5:10 PM

1. Install the engine electrical center bracket assembly to the front fender.
NOTE: Refer to Fastener Notice in Service Precautions.
2. Install the 4 retaining bolts (1).
Tighten
Tighten the 4 retaining bolts (1) to 9 N.m (80 lb in).
Fuse Block |Service and Repair, Procedures: Underhood Electrical Center... http://repair.alldata.com/alldata/article/displa .action?componentId=117...
6 of 10 6/10/2013 5:10 PM

3. Align the electrical center block (1) stubs in the slots so that the tabs (2) retains it in place.
Fuse Block |Service and Repair, Procedures: Underhood Electrical Center... http://repair.alldata.com/alldata/article/displa .action?componentId=117...
7 of 10 6/10/2013 5:10 PM

4. Connect the wire connectors to the lower portion of the electrical center block.
. Connect the wire connectors with the bolts to the electrical center block.
Tighten
Tighten all connector bolts (1) to 9 N.m (80 lb in).
6. Ensure all wire connectors are securely connected.
7. Set the electrical center block in its resting position till the tabs (3) locks in place.
Fuse Block |Service and Repair, Procedures: Underhood Electrical Center... http://repair.alldata.com/alldata/article/displa .action?componentId=117...
8 of 10 6/10/2013 5:10 PM

8. Install the lower part of the cover (1).
9. With the cover (2) off, use the fuse location information to install all fuses and relays.
10. Install the cover.
Fuse Block |Service and Repair, Procedures: Underhood Electrical Center... http://repair.alldata.com/alldata/article/displa .action?componentId=117...
9 of 10 6/10/2013 5:10 PM

11. Install the fender upper brace.
12. Install the 4 fender upper brace bolts.
Tighten
Tighten the 4 retaining bolts to 2 N.m (18 lb ft).
13. Connect the negative battery cable.
14. Start vehicle and ensure all components function properly.
© 2013 ALLDATA, LLC. All Rights Reserved. (Version 2.0.13469)
Fuse Block |Service and Repair, Procedures: Underhood Electrical Center... http://repair.alldata.com/alldata/article/displa .action?componentId=117...
10 of 10 6/10/2013 5:10 PM