ALLIANCE CHD25G2-CA025L Owner's manual

Installation/Operation/Maintenance
www.alliancelaundry.com Part No. 70458301ENR6
June 2013
Tumble Dryers
25 Pound (11,3 Kilogram) Capacity
30 Pound (13,6 Kilogram) Capacity
35 Pound (16 Kilogram) Capacity
Stacked 30 Pound (13,6 Kilogram) Capacity
Stacked 45 Pound (20,4 Kilogram) Capacity
55 Pound (25 Kilogram) Capacity
Starting Serial No. 0602004144
Refer to Page 6 for Model Identification
START
25
C
HIGH
TEMP
MED
TEMP
LOW
TEMP
NO
HEAT
123
SELECT
TEMP
INSERT
COIN
PUSH
START
123
SELECT
TEMP
INSERT
COIN
PUSH
START
START
25
C
HIGH
TEMP
MED
TEMP
LOW
TEMP
NO
HEAT
T477C
T478C
Original Instructions
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
70458301ENR6 1
Installation must conform with local codes or, in the absence of local codes, with:
In the U.S.A., installation must conform to the latest edition of the American National Standard Z223.1/
NFPA 54 “National Fuel Gas Code” and Standard ANSI/NFPA 70 “National Electric Code.”
In Canada, installation must comply with Standards CAN/CSA-B149.1 or Natural Gas and Propane
Installation Code and CSA C22.1, latest edition, Canadian Electric Code, Part I.
In Australia and New Zealand, installation must comply with the Gas Installations Standard AS/NZS 5601
Part 1: General Installations.
IMPORTANT: Information must be obtained from a local gas supplier on instructions to be followed if the
user smells gas. These instructions must be posted in a prominent location. Step-by-step instructions of the
above safety information must be posted in a prominent location near the tumble dryer for customer use.
IMPORTANT: The installer must fully test the tumble dryer after installation and demonstrate to the owner
how to operate the machine.
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.
• WHAT TO DO IF YOU SMELL GAS:
– Do not try to light any appliance.
– Do not touch any electrical switch; do not use any phone in your building.
– Clear the room, building or area of all occupants.
– Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s
instructions.
– If you cannot reach your gas supplier, call the fire department.
• Installation and service must be performed by a qualified installer, service agency or the
gas supplier. W052
FOR YOUR SAFETY, the information in this manual must be followed to minimize the risk
of fire or explosion or to prevent property damage, personal injury or death. W033
WARNING

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
270458301ENR6
The following information applies to the state of Massachusetts, USA.
This appliance can only be installed by a Massachusetts licensed plumber or gas fitter.
This appliance must be installed with a 91 cm (36 inch) long flexible gas connector.
A “T-Handle” type gas shut-off valve must be installed in the gas supply line to this appliance.
This appliance must not be installed in a bedroom or bathroom.
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumble dryer before servicing.
• Close gas shut-off valve to gas tumble dryer before servicing.
• Close steam valve to steam tumble dryer before servicing.
• Never start the tumble dryer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the tumble dryer is properly grounded. W002R1
WARNING
• Installation of unit must be performed by a qualified installer.
• Install tumble dryer according to manufacturer’s instructions and local codes.
• DO NOT install a tumble dryer with flexible plastic venting materials. If flexible metal (foil
type) duct is installed, it must be of a specific type identified by the appliance manufacturer
as suitable for use with tumble dryer. Refer to section on connecting exhaust system.
Flexible venting materials are known to collapse, be easily crushed, and trap lint. These
conditions will obstruct tumble dryer airflow and increase the risk of fire. W752R1
WARNING

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
70458301ENR6 3
© Copyright 2013, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
Table of
Contents
Introduction......................................................................................... 6
Model Identification ............................................................................. 6
Contact Information.............................................................................. 9
Safety Information.............................................................................. 10
Important Safety Instructions ............................................................... 11
Specifications and Dimensions........................................................... 13
Cabinet Dimensions – 025, 030, 035 and 055 Series........................... 15
Cabinet Dimensions – T30 and T45 Series .......................................... 16
Exhaust Outlet Locations – 025, 030, 035 and 055 Series................... 17
Exhaust Outlet Locations – T30 and T45 Series.................................. 18
Gas Connection Locations – 025, 030, 035 and 055 Series................. 19
Gas Connection Locations – T30 and T45 Series ................................ 20
Electrical Connection Locations – 025, 030, 035 and 055 Series........ 21
Electrical Connection Locations – T30 and T45 Series ....................... 22
Steam Connection Locations – 025, 030 and 035 Series...................... 23
Steam Connection Locations – T30 Series........................................... 24
Installation........................................................................................... 25
Pre-Installation Inspection.................................................................... 25
Location Requirements......................................................................... 25
Position and Level the Tumble Dryer................................................... 27
Fire Suppression System....................................................................... 28
Check Local Codes and Permits...................................................... 28
Water Requirements......................................................................... 28
Water Connections........................................................................... 28
Electrical Requirements................................................................... 29
Auxiliary Alarm............................................................................... 30
To Reverse the Loading Door – 025, 030, 035 and 055 Series............ 30
Before Placing Tumble Dryer into Service .......................................... 33
Required for CE Models Only......................................................... 35
Installing CE Gas Tumble Dryer.......................................................... 36
General Information......................................................................... 36
CE Orifices....................................................................................... 37
Properties of CE Gases .................................................................... 38
Basic Configuration ......................................................................... 39
Specific Conversion Procedures ...................................................... 39
Exhaust Requirements ....................................................................... 42
Layout................................................................................................... 42
Make-Up Air......................................................................................... 42
Venting ................................................................................................. 42
Individual Venting ........................................................................... 43
Manifold Venting............................................................................. 45
Gas Requirements............................................................................... 48
Gas Supply Pipe Sizing and Looping................................................... 50
High Altitude Burner Orifice Sizing..................................................... 52

470458301ENR6
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
Electrical Requirements..................................................................... 54
Wiring Diagram.................................................................................... 54
Grounding Instructions......................................................................... 55
For CE Models Only........................................................................ 55
Service/Ground Location................................................................. 56
To Connect Electrical Service To The Tumble Dryer.......................... 59
Configuring Your Tumble Dryer for Other Service Voltages......... 59
Electrical Connections for T30 and T45 Only................................. 59
Conversion Instructions........................................................................ 60
Ferrite Ring Installation (025, 030, 035 and 055 Series Only)............. 62
Electrical Specifications ....................................................................... 63
Steam Requirements........................................................................... 68
Piping Recommendations..................................................................... 68
Installing Steam Trap and Making Condensate Return
Connections........................................................................................ 69
Single Drop Timer .............................................................................. 71
Power-Up Mode.................................................................................... 71
Ready Mode.......................................................................................... 71
Start Mode ............................................................................................ 71
Run Mode ............................................................................................. 71
Setting Dry Time Dipswitches.............................................................. 71
Resetting Cycle Time to Zero............................................................... 71
Dipswitch Settings................................................................................ 72
Operating Instructions....................................................................... 74
Emergency Stop Button on CE Models................................................ 74
Operating Instructions .......................................................................... 75
Control Instructions.............................................................................. 76
Dual Digital Timer Control.............................................................. 76
Electronic OPL Micro Control......................................................... 78
Single Drop Control......................................................................... 79
MDC Coin and Card Control........................................................... 81
Quantum Control ............................................................................. 82
Galaxy 600 Control.......................................................................... 83
LED OPL Control............................................................................ 84
UniLinc Control............................................................................... 85
DX4 Coin Control............................................................................ 86
DX4 OPL Control............................................................................ 86
Diagnostic Microprocessor Control................................................. 87
DMP OPL Models ........................................................................... 88
DMP Coin........................................................................................ 90
Ignition Control Operation and Troubleshooting for
Models Starting 3/11/13..................................................................... 94
Internal Control Failure.................................................................... 94
Troubleshooting............................................................................... 94
Proper Electrode Location ............................................................... 95
Flame Current Measurement............................................................ 95
Ignition Control Operation for
Non-CE Models Through 3/10/13...................................................... 96
Ignition Control Operation for
CE Models Through 3/10/13.............................................................. 97

70458301ENR6 5
© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
Adjustments......................................................................................... 99
Airflow Switch...................................................................................... 99
Loading Door Switch............................................................................ 99
Door Strike............................................................................................ 100
Maintenance........................................................................................ 101
Daily ..................................................................................................... 101
Monthly................................................................................................. 102
Quarterly............................................................................................... 102
Bi-Annually .......................................................................................... 102
Annually ............................................................................................... 102
Fire Suppression System Maintenance Test .................................... 103
Before You Call for Service............................................................... 105
Removing Tumble Dryer from Service............................................. 105
Disposal of Unit................................................................................... 106

70458301ENR6
6© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
Introduction
Model Identification
Information in this manual is applicable to these models:
Gas Steam Electric
025
Series
CHD25G2-CA025L
CHD25G2-CA025N
CHD25G2-CT025L
CHD25G2-CT025N
CHD25G2-CU025L
CHD25G2-CU025N
CK025N
DR25G2-BA025L
DR25G2-BA025N
DR25G2-BK025N
DR25G2-BT025L
DR25G2-BT025N
DR25G2-BU025L
DR25G2-BU025N
HA025L
HA025N
HK025N
HT025L
HT025N
HU025L
HU025N
IPD25G2
IT025L
IT025N
SA025L
SA025N
SK025N
ST025L
ST025N
SU025L
SU025N
UA025L
UA025N
UK025N
UT025L
UT025N
UU025L
UU025N
YT025L
YT025N
YU025L
YU025N
CHD25S2-CT025S
CHD25S2-CU025S
DR25S2-BT025S
DR25S2-BU025S
HT025S
HU025S
IPD25S2
IT025S
ST025S
SU025S
UT025S
UU025S
YT025S
YU025S
CHD25E2-CT025E
CHD25E2-CU025E
DR25E2-BT025E
DR25E2-BU025E
HT025E
HU025E
IPD25E2
IT025E
ST025E
SU025E
UT025E
UU025E
YT025E
YU025E
030
Series
CHD30G2-CA030L
CHD30G2-CA030N
CHD30G2-CT030L
CHD30G2-CT030N
CHD30G2-CU030L
CHD30G2-CU030N
CK030N
DR30G2-BA030L
DR30G2-BA030N
DR30G2-BK030N
DR30G2-BT030D
DR30G2-BT030L
DR30G2-BT030N
DR30G2-BU030L
DR30G2-BU030N
HA030L
HA030N
HK030N
HT030D
HT030L
HT030N
HU030L
HU030N
IPD30G2
IT030L
IT030N
SA030L
SA030N
SK030N
ST030D
ST030L
ST030N
SU030L
SU030N
UA030L
UA030N
UK030N
UT030L
UT030N
UU030L
UU030N
YT030L
YT030N
YU030L
YU030N
CHD30S2-CT030S
CHD30S2-CU030S
DR30S2-BT030S
DR30S2-BU030S
HT030S
HU030S
IPD30S2
IT030S
ST030S
SU030S
UT030S
UU030S
YT030S
YU030S
CHD30E2-CT030E
CHD30E2-CU030E
DR30E2-BT030E
DR30E2-BU030E
HT030E
HU030E
IPD30E2
IT030E
ST030E
SU030E
UT030E
UU030E
YT030E
YU030E
T30
Series
CHD30STG2-CAT30L
CHD30STG2-CAT30N
CHD30STG2-CTT30L
CHD30STG2-CTT30N
CHD30STG2-CUT30L
CHD30STG2-
CUT30N
CKT30N
DR335
DR335G2-BKT30N
DRST30G2-BAT30L
DRST30G2-BAT30N
DRST30G2-BTT30D
DRST30G2-BTT30L
DRST30G2-BTT30N
DRST30G2-BUT30L
DRST30G2-BUT30N
HAT30L
HAT30N
HKT30N
HTT30D
HTT30L
HTT30N
HUT30L
HUT30N
IPD30STG2
ITT30L
ITT30N
MTT30N
NTT30N
SAT30L
SAT30N
SKT30N
STT30D
STT30L
STT30N
SUT30L
SUT30N
UAT30L
UAT30N
UKT30N
UTT30L
UTT30N
UUT30L
UUT30N
CHD30STS2-CTT30S
CHD30STS2-CUT30S
DRST30S2-BTT30S
DRST30S2-BUT30S
HTT30S
HUT30S
IPD30STS2
ITT30S
STT30S
SUT30S
UTT30S
UUT30S
CHD30STE2-CTT30E
CHD30STE2-
CUT30E
DRST30E2-BTT30E
DRST30E2-BUT30E
HTT30E
HUT30E
IPD30STE2
ITT30E
STT30E
SUT30E
UTT30E
UUT30E
(Continued)

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
Introduction
7
70458301ENR6
(Continued)
Gas Steam Electric
035
Series
AT035L
AT035N
CHD35G2-CA035L
CHD35G2-CA035N
CHD35G2-CT035L
CHD35G2-CT035N
CHD35G2-CU035L
CHD35G2-CU035N
CK035N
DR35G2-BA035L
DR35G2-BA035N
DR35G2-BK035N
DR35G2-BT035L
DR35G2-BT035N
DR35G2-BU035L
DR35G2-BU035N
HA035L
HA035N
HK035N
HT035L
HT035N
HU035L
HU035N
IPD35G2
IT035L
IT035N
SA035L
SA035N
SK035N
ST035L
ST035N
SU035L
SU035N
UA035L
UA035N
UK035N
UT035L
UT035N
UU035L
UU035N
YT035L
YT035N
YU035L
YU035N
AT035S
CHD35S2-CT035S
CHD35S2-CU035S
DR35S2-BT035S
DR35S2-BU035S
HT035S
HU035S
IPD35S2
IT035S
ST035S
SU035S
UT035S
UU035S
YT035S
YU035S
AT035E
CHD35E2-CT035E
CHD35E2-CU035E
DR35E2-BT035E
DR35E2-BU035E
HT035E
HU035E
IPD35E2
IT035E
ST035E
SU035E
UT035E
UU035E
YT035E
YU035E
T45
Series
CKT45N
CTT45L
CTT45N
DR445G2-BAT45L
DR445G2-BAT45N
DR445G2-BKT45N
DR445G2-BTT45D
DR445G2-BTT45L
DR445G2-BTT45N
DR445G2-BUT45L
DR445G2-BUT45N
DRST45G2-BAT45L
DRST45G2-BAT45N
DRST45G2-BTT45D
DRST45G2-BTT45L
DRST45G2-BTT45N
DRST45G2-BUT45L
DRST45G2-BUT45N
HAT45L
HAT45N
HKT45N
HTT45D
HTT45L
HTT45N
HUT45L
HUT45N
IPD45STG2
ITT45L
ITT45N
MTT45N
NTT45N
SAT45L
SAT45N
SKT45N
STT45D
STT45L
STT45N
SUT45L
SUT45N
UAT45L
UAT45N
UKT45N
UTT45L
UTT45N
UUT45L
UUT45N Not Applicable Not Applicable
055
Series
CA055L
CA055N
CK055N
CT055L
CT055N
CU055L
CU055N
DR55SG2-BA055L
DR55SG2-BA055N
DR55SG2-BK055N
DR55SG2-BT055D
DR55SG2-BT055L
DR55SG2-BT055N
DR55SG2-BU055L
DR55SG2-BU055N
HA055L
HA055N
HK055N
HT055D
HT055L
HT055N
HU055L
HU055N
IPD55G2
IT055L
IT055N
SA055L
SA055N
SK055N
ST055D
ST055L
ST055N
SU055L
SU055N
UA055L
UA055N
UK055N
UT055L
UT055N
UU055L
UU055N
Not Applicable
CT055E
CU055E
DR55SE2-BT055E
DR55SE2-BU055E
HT055E
HU055E
IPD55E2
IT055E
ST055E
SU055E
UT055E
UU055E
(see next page for suffixes)

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
Introduction
70458301ENR6
8
Includes models with the following control suffixes:
3B – reversing DX4 vended
3O – DX4 OPL
3V – DX4 vended
3W – reversing DX4 prep for coin
3X – DX4 prep for coin
BB – reversing basic electronic, coin
BC – basic electronic, coin
BG – basic electronic, OPL mode
BL – basic electronic, central pay
BW – reversing basic electronic, prep
for coin
BX – basic electronic, prep for coin
BY – basic electronic, prep for card
BZ – reversing basic electronic, prep
for card
DO – DMP OPL
DV – DMP vended
DX – DMP prep for coin
EO – LED OPL
KB – reversing single coin
KC – single coin
KW – reversing prep for coin
KX – prep for coin
KY – prep for card
KZ – reversing prep for card
LB – reversing network adaptable
coin
LC – network adaptable coin
LW – reversing network adaptable,
prep for coin
LX – network adaptable, prep for
coin
LY – network adaptable, prep for
card
LZ – reversing network adaptable,
prep for card
NC – NetMaster coin
NR – NetMaster card
NX – NetMaster, prep for coin
NY – NetMaster, prep for card
OM – OPL micro
QT – dual digital timer
R3 – reversing DX4 OPL
RE – reversing LED OPL
RQ – reversing dual digital timer
RU – reversing UniLinc OPL
SD – single drop
SX – single drop, prep for coin
UO – UniLinc OPL
WB – reversing network ready coin
WC – network ready coin
WW –reversing network ready, prep
for coin
WX – network ready, prep for coin
WY – network ready, prep for card
WZ – reversing network ready, prep
for card
ZC – NetMaster network coin
ZR – NetMaster network card
ZX – NetMaster network, prep for
coin
ZY – NetMaster network, prep for
card

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
Introduction
9
70458301ENR6
Contact Information
If service is required, contact the nearest Factory
Authorized Service Center.
If you are unable to locate an authorized service center
or are unsatisfied with the service performed on your
unit, contact:
Alliance Laundry Systems
Shepard Street
P.O. Box 990
Ripon, WI 54971-0990
U.S.A.
www.alliancelaundry.com
Phone: [phone] Ripon, Wisconsin
[phone] Wevelgem, Belgium
When calling or writing about your unit, PLEASE
GIVE THE MODEL AND SERIAL NUMBERS. The
model and serial numbers are located on the
nameplate. The nameplate will be in the location
shown in Figure 1.
Date Purchased ______________________________
Model Number ______________________________
Serial Number _______________________________
Please include a copy of your bill of sale and any
service receipts you have.
If replacement parts are required, contact the source
from where you purchased your tumble dryer or call
[phone] or [phone] for the name
and address of the nearest authorized parts distributor.
To reduce the risk of serious injury or death,
DO NOT repair or replace any part of the unit
or attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that you understand and have
the skills to carry out. W329
WARNING
1Serial Plate
Figure 1
TMB1974N
1
1
TMB2098N TMB1974N

70458301ENR6
10 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
Safety Information
Precautionary statements (“DANGER,” “WARNING,”
and “CAUTION”), followed by specific instructions,
are found in this manual and on machine decals. These
precautions are intended for the personal safety of the
operator, user, servicer, and those maintaining the
machine.
Additional precautionary statements (“IMPORTANT”
and “NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used
to inform the reader of specific procedures where
minor machine damage will occur if the procedure
is not followed.
NOTE: The word “NOTE” is used to communicate
installation, operation, maintenance or servicing
information that is important but not hazard
related.
NOTE: The WARNING and IMPORTANT
instructions appearing in this manual are not
meant to cover all possible conditions and
situations that may occur. It must be understood
that common sense, caution and carefulness are
factors which CANNOT be built into this tumble
dryer. These factors MUST BE supplied by the
person(s) installing, maintaining or operating the
tumble dryer.
Always contact your dealer, distributor, service agent
or the manufacturer on any problems or conditions you
do not understand.
Indicates an imminently hazardous
situation that, if not avoided, will cause
severe personal injury or death.
DANGER
Indicates a hazardous situation that, if not
avoided, could cause severe personal
injury or death.
WARNING
Indicates a hazardous situation that, if not
avoided, may cause minor or moderate
personal injury or property damage.
CAUTION
Failure to install, maintain, and/or operate
this machine according to manufacturer’s
instructions may result in conditions which
can produce serious injury, death and/or
property damage. W051R1
WARNING

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
Safety Information
11
70458301ENR6
Save These Instructions
Important Safety Instructions
1. Read all instructions before using the tumble
dryer.
2. Install the tumble dryer according to the
INSTALLATION instructions. Refer to the
EARTHING (grounding) instructions for the
proper earthing (grounding) of the tumble dryer.
All connections for electrical power, earthing
(grounding) and gas supply must comply with
local codes and be made by licensed personnel
when required. It is recommended that the
machine be installed by qualified technicians.
3. Do not install or store the tumble dryer where it
will be exposed to water and/or weather. The
tumble dryer cannot be used in a closed room
where the air supply is insufficient. If necessary,
ventilation grids must be installed in the doors or
the windows.
4. This appliance must not be activated without lint/
foam filter.
5. When you perceive a gas odor, immediately
switch off the gas supply and ventilate the room.
Do not switch on electrical appliances and do not
pull electrical switches. Do not use matches or
lighters. Do not use a phone in the building. Warn
the fitter, and if so desired, the gas company, as
soon as possible.
6. To avoid fire and explosion, keep surrounding
areas free of flammable and combustible
products. Regularly clean the dryer drum and
exhaust tube should be cleaned periodically by
competent maintenance personnel. Daily remove
piled up dust from filter and inside of filter
compartment.
7. Do not use or store flammable materials near this
appliance.
8. Do not dry articles that have been previously
cleaned in, washed in, soaked in or spotted with
gasoline or machine oils, vegetable or cooking
oils, cleaning waxes or chemicals, dry-cleaning
solvents, thinner or other flammable or explosive
substances as they give off vapors that could
ignite, explode or cause fabric to catch on fire by
itself.
9. Do not spray aerosols in the vicinity of this
appliance while it is in operation.
10. Items such as foam rubber (latex foam), shower
caps, waterproof textiles, rubber backed articles
and clothes or pillows filled with foam rubber
pads should not be dried in the tumble dryer. Do
not use the appliance to dry materials with a low
melting temperature (PVC, rubber, etc.).
11. Do not tumble fiberglass curtains and draperies
unless the label says it can be done. If they are
dried, wipe out the cylinder with a damp cloth to
remove particles of fiberglass.
12. Do not allow children on or in the tumble dryer.
This appliance is not intended for use by young
children or infirm persons without supervision.
Young children should be supervised to ensure
that they do not play with the appliance.
13. Do not reach into the tumble dryer if the cylinder
is revolving.
14. Use tumble dryer only for its intended purpose,
drying fabrics. Always follow the fabric care
instructions supplied by the textile manufacturer
and only use the dryer drum to dry textiles that
have been washed in water. Only insert spin-
dried linen in the dryer.
15. Always read and follow manufacturer’s
instructions on packages of laundry and cleaning
aids. Heed all warnings or precautions. To reduce
the risk of poisoning or chemical burns, keep
them out of the reach of children at all times
(preferably in a locked cabinet).
16. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
17. Remove laundry immediately after tumble dryer
stops.
To reduce the risk of fire, electric shock,
serious injury or death to persons when
using your tumbler, follow these basic
precautions. W776
WARNING

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
Safety Information
70458301ENR6
12
18. DO NOT operate the tumble dryer if it is
smoking, grinding or has missing or broken parts
or removed guards or panels. DO NOT tamper
with the controls or bypass any safety devices.
19. Tumble dryer will not operate with the loading
door open. DO NOT bypass the door safety
switch to permit the tumble dryer to operate with
the door open. The tumble dryer will stop
tumbling when the door is opened. Do not use the
tumble dryer if it does not stop tumbling when
the door is opened or starts tumbling without
pressing or turning the START mechanism.
Remove the tumble dryer from use and call for
service.
20. Tumble dryer(s) will not operate with lint panel
open. DO NOT bypass lint panel safety switch to
permit the tumble dryer to operate with the lint
panel open.
21. Do not modify this appliance.
22. Always clean the lint filter daily. Keep area
around the exhaust opening and adjacent
surrounding area free from the accumulation of
lint, dust and dirt. The interior of the tumble
dryer and the exhaust duct should be cleaned
periodically by qualified service personnel.
23. Solvent vapors from dry-cleaning machines
create acids when drawn through the heater of the
drying unit. These acids are corrosive to the
tumble dryer as well as the laundry load being
dried. Be sure make-up air is free of solvent
vapors.
24. At the end of each working day, close off all main
supplies of gas, steam and current.
25. Do not repair or replace any part of the tumble
dryer, or attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that the user understands and has the
skills to carry out. ALWAYS disconnect and
lockout the electrical power to the tumble dryer
before servicing. Disconnect power by shutting
off appropriate breaker or fuse.
26. Before the tumble dryer is removed from service
or discarded, remove the door to the drying
compartment and the door to the lint
compartment.
27. Failure to install, maintain, and/or operate this
tumble dryer according to the manufacturer’s
instructions may result in conditions which can
produce bodily injury and/or property damage.
NOTE: The WARNINGS and IMPORTANT
SAFETY INSTRUCTIONS appearing in this
manual are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution and care must be exercised when
installing, maintaining, or operating the tumble
dryer.
Always contact your dealer, distributor, service agent
or the manufacturer on any problems or conditions you
do not understand.

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 13
70458301ENR6
Specifications and Dimensions
NOTE: All machines are shipped with extra nipple
to convert to metric thread (from Standard).
Specifications 025 Series 030 Series 035 Series 055 Series
Noise level measured during
operation at operator position of
3.3 feet (1 meter) in front of machine
and 5.2 feet (1.6 meters) from floor 60 dBA 61 dBA 63 dBA 63 dBA
Net Weight (approximate):
Pounds (kg ) 300
(137) 330 (150) 360 (163) 435 (197)
Standard Packaging Weight:
Pounds (kg ) 332
(151) 364 (165) 394 (179) 476 (216)
Standard Packaging Shipping
Dimensions:
Inch (mm)
30 x 43 x 69
(762 x 1,092 x
1,753)
30 x 49 x 69
(762 x 1,245 x
1,753)
33 x 49 x 69
(838 x 1,245 x
1,753)
35.5 x 59 x 72
(902 x 1,499 x
1,829)
Slat Crate Packaging Weight:
Pounds (kg ) 406
(184) 446 (202) 480 (218) 506 (230)
Slat Crate Shipping Dimensions:
Inch (mm)
34.5 x 46 x 87.75
(876 x 1,168 x
2,229)
34.5 x 52 x 87.75
(876 x 1,321 x
2,229)
37.5 x 52 x 87.75
(953 x 1,321 x
2,229)
40 x 60 x 87.25
(1,016 x 1,524 x
2,216)
Cylinder Size:
Inch (mm) 26.5 x 24
(673 x 610) 26.5 x 30 (673 x 762) 30 x 30 (762 x 762) 33 x 35 (838 x 889)
Cylinder Capacity (dry weight):
Pounds (kg ) 25
(11.3) 30 (13.6) 35 (15.9) 55 (24.9)
Drive Motor:
Horsepower (kW)
1/4
(0.1865) 1/4 (0.1865) 1/4 (0.1865) Nonreversing 1/2 (0.373)
Reversing
1/4 (0.1865)
Fan Motor:
Horsepower (kW) 1/4
(0.1865) 1/4
(0.1865) 1/4 (0.1865) 1/2 (0.373)
Maximum Airflow per
Pocket: C.F.M. (l/sec)
50 Hertz 430
(203) 430 (203) 550 (260) 600 (283)
60 Hertz 500
(236) 500 (236) 650 (307) 700 (330)
Maximum Static Back
Pressure:
Inch W.C. (mbar, kPa)
50 Hertz 0.6
(1.5, 0.15) 0.6 (1.5, 0.15) 0.5 (1.3, 0.13) 0.5 (1.3, 0.13)
60 Hertz 0.8
(2.0, 0.2) 0.8 (2.0, 0.2) 0.6 (1.5, 0.15) 0.6 (1.5, 0.15)
Gas Models
Gas Connection 1/2 in. NPT 1/2 in. NPT 1/2 in. NPT 1/2 in. NPT
Gas Burner Rating:
Btu/hr. (kW, Mj/hr.)
50 Hertz 64,000
(18.7, 67.5) 73,000 (21.4, 77) 90,000 (26.4, 95) 102,000 (29.9, 107.6)
60 Hertz 64,000
(18.7, 67.5) 73,000 (21.4, 77) 90,000 (26.4, 95) 112,000 (32.8, 118.2)
Electric Models
Heating Element Rating: 400/50/3 10 kW 21 kW 24 kW 27 kW
Standard 12 kW
Steam Models
Steam Connection 3/4 in. NPT 3/4 in. NPT 3/4 in. NPT N/A
Steam Coil Rating at 100 psig:
Boiler Horsepower (Btu/hr.)
(recommended operating
pressure 80-100 psig)
3.9
(134,700) 3.9 (134,700) 4.8 (166,000) N/A
N/A = Not Applicable

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
Specifications and Dimensions
70458301ENR6
14
N/A = Not Applicable
NOTE: All machines are shipped with extra nipple
to convert to metric thread (from Standard).
Specifications T30 Series T45 Series
Noise level measured during operation at operator
position of 3.3 feet (1 meter) in front of machine and
5.2 feet (1.6 meters) from floor
66 dBA 67 dBA
Net Weight (approximate):
Pounds (kg) 544
(247) 673 (305)
Standard Packaging Weight:
Pounds (kg) 582
(264) 718 (326)
Standard Packaging Shipping Dimensions:
Inch (mm) 32.5 x 47 x 81
(826 x 1,194 x 2,057) 35.5 x 54 x 85 (902 x 1,372 x 2,159)
Slat Crate Packaging Weight:
Pounds (kg) 661
(300) 748 (339)
Slat Crate Shipping Dimensions:
Inch (mm) 37 x 50 x 87.75
(940 x 1,270 x 2,229) 40 x 57 x 87.25 (1,016 x 1,448 x 2,216)
Cylinder Size:
Inch (mm) 30 x 26
(762 x 660) 33 x 30 (838 x 762)
Cylinder Capacity (dry weight):
kg (Pounds) 2 x 30
(2 x 13.6) 2 x 45 (2 x 20.5)
Drive Motor**:
Horsepower (kW) 1/4
(0.1865) 1/2 (0.373)
Fan Motor**:
Horsepower (kW) 1/4
(0.1865) 1/2 (0.373)
Maximum Airflow per Pocket**:
C.F.M. (l/sec)
50 Hertz 340
(160) 500 (236)
60 Hertz 400
(189) 600 (283)
Maximum Static Back Pressure*:
Inch W.C. (mbar, kPa)
50 Hertz 0.8
(2.0, 0.2) 0.8 (2.0, 0.2)
60 Hertz 0.9
(2.3, 0.23) 0.9 (2.3, 0.23)
Gas Models
Gas Connection 1/2 in. NPT 1/2 in. NPT
Gas Burner Rating**:
Btu/hr. (kW, Mj/hr.)
50 Hertz 73,000
(21.4, 77) 87,000 (25.5, 91.8)
60 Hertz 73,000
(21.4, 77) 95,000 (27.8, 100.2)
Electric Models
Heating Element Rating**: 21 kW N/A
Steam Models
Steam Connection 3/4 in. NPT N/A
Steam Coil Rating at 100 psig**:
Boiler Horsepower (Btu/hr.) (recommended operating
pressure 80-100 psig)
3.2
(111,000) N/A
* with both pockets running
** for each pocket

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
Specifications and Dimensions
15
70458301ENR6
Cabinet Dimensions – 025, 030, 035 and 055 Series
* Fire suppression system optional - may not be on machine.
NOTE: Facia panels available to increase height of
models to 72.25 inches (1,835 mm) and 76.25 inches
(1,938 mm).
TMB2292N
B
A
C
H
E
F
D
G
J
I
K
L
Models A B C D E F*
025 Series 26.25 in.
(667 mm) 27.5 in. (669 mm) 23.35 in. (593 mm) 25.75 in. (654 mm) 40.875 in. (1,038 mm) 6.53 in. (166 mm)
030 Series 26.25 in.
(667 mm) 27.5 in. (669 mm) 28.35 in. (720 mm) 31.75 in. (806 mm) 46.875 in. (1,191 mm) 6.53 in. (166 mm)
035 Series 28 in.
(711 mm) 27.5 in. (669 mm) 28.35 in. (720 mm) 31.75 in. (806 mm) 46.875 in. (1,191 mm) 6.53 in. (166 mm)
055 Series 31.88 in.
(810 mm) 26.87 in. (682.5 mm) 33.75 in. (857.25 mm) 38.25 in. (971.5 mm) 53.62 in. (1,365 mm) 6.53 in. (166 mm)
Models G H* I* J* K L
025 Series 63.875 in.
(1,622 mm) 16.48 in. (419 mm) 15.41 in. (391 mm) 1.59 in. (40 mm) 24.64 in. (626 mm) 28 in. (711 mm)
030 Series 63.875 in.
(1,622 mm) 16.48 in. (419 mm) 15.41 in. (391 mm) 1.59 in. (40 mm) 24.64 in. (626 mm) 28 in. (711 mm)
035 Series 63.875 in.
(1,622 mm) 16.48 in. (419 mm) 19.59 in. (497.5 mm) 1.59 in. (40 mm) 27.38 in. (695 mm) 31.5 in. (800 mm)
055 Series 66.72 in.
(1,694.7 mm) 17.75 in. (451 mm) 18.65 in. (474 mm) 1.59 in.
(40 mm) 30.5 in. (774.7 mm) 34.5 in. (876 mm)

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
Specifications and Dimensions
70458301ENR6
16
Cabinet Dimensions – T30 and T45 Series
NOTE: To meet ADA compliance, install a 4 inch
(102 mm) riser on T30 models only.
TMB2332N
TMB2332N
C
E
FH
J
B
D
G I
A
ModelsABCDE
T30 Series 28 in.
(711 mm) 49 in. (1,245 mm) 48.25 in. (1,226 mm) 11.4 in. (290 mm) 10.7 in. (272 mm)
T45 Series 31.88 in.
(810 mm) 50.4 in. (1,280 mm) 49.3 in. (1,252 mm) 10.3 in. (262 mm) 9.3 in. (236 mm)
Models F G H I J
T30 Series 25.02 in.
(636 mm) 42.76 in. (1,086 mm) 27.38 in. (695 mm) 31.5 in. (800 mm) 76.25 in. (1,937 mm)
T45 Series 29.37 in.
(746 mm) 48.62 in. (1,235 mm) 30.50 in. (775 mm) 34.5 in. (876 mm) 81.25 in. (2,063.75 mm)

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
Specifications and Dimensions
17
70458301ENR6
Exhaust Outlet Locations – 025, 030, 035 and 055 Series
TMB2132N
B
A
Models Rear Exhaust
Diameter A B
025/030 Series 6 in.
(152 mm) 3.875 in. (99 mm) 4.625 in. (117 mm)
035 Series 8 in.
(203 mm) 4.875 in. (124 mm) 5.625 in. (143 mm)
055 Series 8 in.
(203 mm) 4.808 in. (122 mm) 6.156 in. (156.3 mm)

© Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT
Specifications and Dimensions
70458301ENR6
18
Exhaust Outlet Locations – T30 and T45 Series
TMB1969N
TMB1969N
B
C
A
Models Rear Exhaust
Diameter A B C
T30 Series Elliptical
Fits 8 in. (203 mm) 36.54 in. (928 mm) 4.25 in. (108 mm) 62.42 in. (1,585 mm)
T45 Series Elliptical
Fits 10 in. (254 mm) 40.88 in. (1,038 mm) 4.75 in. (121 mm) 66.00 in. (1,676 mm)