Allied Telesis AT-9900s Series User manual

A5 Quick Install Guide Cover
AT-9900s Switches
Expansion Module
Installation Guide
AT-A60
AT-A61
AT-A62
613-000032 REV B

AT-9900s Series Switch Expansion Modules
2
Expansion Module Installation Guide for AT-9900s Switches
Document Number 613-000032 REV B
© 2005 Allied Telesyn Inc. All rights reserved. No part of this publication may be
reproduced without prior written permission from Allied Telesyn Inc.
Allied Telesyn Inc. reserves the right to change specifications and other
information in this document without prior written notice. The information
provided herein is subject to change without notice. In no event shall Allied
Telesyn Inc. be liable for any incidental, special, indirect, or consequential
damages whatsoever, including but not limited to lost profits, arising out of or
related to this manual or the information contained herein, even if Allied Telesyn
Inc. has been advised of, known, or should have known, the possibility of such
damages.
All company names, logos, and product designs that are trademarks or
registered trademarks are the property of their respective owners.

Installation Guide
3
Contents
Models Covered by this Guide ...................................................................................... 4
Package Contents ............................................................................................................. 4
Overview ............................................................................................................................ 4
XFP Port ............................................................................................................................. 5
SFP Ports ............................................................................................................................ 7
RJ-45 Ports ......................................................................................................................... 9
Installation Procedure .................................................................................................... 10
Documentation ............................................................................................................... 11

AT-9900s Series Switch Expansion Modules
4
Models Covered by this Guide
■AT-A60 provides a single XFP port
■AT-A61 provides 12 SFP ports
■AT-A62 provides 12 10/100/1000Mbps RJ-45 ports
Package Contents
One warranty card and this Installation Guide are included with each expansion
module. Contact your sales representative if either is damaged or missing.
Overview
Two front bays in the AT-9900s switch allow quick and easy installation of
optional expansion modules (XEMs). These modules enable economical
combinations of speed and port density with the AT-9900s Series gigabit link
aggregation switch.
For example, add one 10GbE expansion module to provide a single high-speed,
high capacity fiber connection; add a second 10GbE module for redundancy or
as bandwidth needs increase. Add one or two 12-port RJ-45 copper expansion
modules to provide maximum gigabit Ethernet port density in a compact 1RU
chassis. For flexible port options, add one or two 12-port SFP expansion
modules to aggregate copper and fiber links from data centres and enterprise
networks, while providing long haul fiber links.

Installation Guide
5
XFP Port
The single-port 10Gigabit Ethernet expansion module, model AT-A60, features
the following:
■support for hot-swappable XFP modules
■two 16MByte DDR-SDRAM for packet buffering
■compatibility with a number of different 10Gb XFP serial transceivers
■status LEDs
■XFP connector, cage, and heatsink are provided for use with any standard
XFP module
Front view AT-A60
The following LEDs report operations on AT-A60 expansion modules.
LED State Description
L/A
(Link Activity)
Green An XFP transceiver is installed and a 10Gb
link has been established.
Green flashing An XFP transceiver is installed and link
activity is occurring.
XFP Green An XFP transceiver is installed and enabled.
No XFP is installed if this light is off.
Amber An XFP transceiver is installed but not
operating.
Amber flashing The installed XFP transceiver has a
transmission fault.
AA
XFP
XFP
L/A
L/A
LINK ACT ENABLED DISABLED FAULT
AT-A 60

AT-9900s Series Switch Expansion Modules
6
The following XFP modules are approved for the AT-A60 expansion module.
For the latest list of approved transceiver modules, contact an authorised
distributor or reseller.
Product No. Media Type Description
AT-XPSR 10GBASE-SR 850nm short-haul transmission, 300m with
MMF.
AT-XPLRM 10GBASE-LRM 1310nm short-haul transmission, 300m with
MMF.
AT-XPLR 10GBASE-LR 1310nm medium-haul transmission, 10km
with SMF.
AT-XPER40 10GBASE-ER 1550nm long-haul transmission, 40km with
SMF.

Installation Guide
7
SFP Ports
The 12-port 1000BASE-X expansion module, model AT-A61, features the
following:
■two rows of 6 SFP ports
■support for hot-swappable SFP modules
■status LEDs
■two 16MByte DDR-SDRAM for packet buffering
■cable fault detection and distance-to-fault diagnostics for copper SFP ports
(see the Test Facility chapter in the Software Reference for the switch)
Front view AT-A61
The following LEDs report operations on AT-A61 expansion modules.
LED State Description
L/A
(Link Activity)
Green An SFP transceiver is installed and a link has
been established.
Green flashing An SFP transceiver is installed and link
activity is occurring.
Amber An SFP transceiver is installed but a link has
not been established.
Amber flashing An SFP is installed but there is a transmission
fault.
1 2 3 4 5 6 7 8 9 10 11 12
PORTS 1-12 LINK
SFP ACT INSTALLED FAULT
AT-A 61

AT-9900s Series Switch Expansion Modules
8
The following SPF modules are approved for AT-A61expansion modules.
For the latest list of approved transceiver modules, contact an authorised
distributor or reseller.
Product No. Media Type Description
AT-SPTX 10/100/1000BASE-T Copper, 100m at 1000Mbps, RJ-45
connector.
AT-SPSX 1000BASE-SX 850nm, 2 to 550 m with 50/125µm fiber,
2m to 275m with 62.5/125µm fiber, LC
connector.
AT-SPLX10 1000BASE-LX 1310nm, 2m to 10km with 9µm SM
fiber, 2m to 550m with 50µm MM fiber,
2m to 550m with 62.5µm MM fiber, LC
connector.
AT-SPLX40 1000BASE-LX 1310nm SM fiber up to 40km, LC
connector
AT-SPLX40/
1550
1000BASE-LX 550nm SM fiber up to 40 km, LC
connector
AT-SPZX80 1000BASE-ZX 1550nm, 80km with 9µm SM fiber, LC
connector.
AT-SPZX80/
xxxx
1000BASE-ZX
CWDM
Wavelengths of 1610nm to 1470nm
(20nm intervals) and 1310nm, 80km
with 9µm SM fiber, LC connector.
Where xxxx can be:
1610 1590 1570 1550
1530 1510 1490 1470

Installation Guide
9
RJ-45 Ports
The 12-port RJ-45 expansion module, model AT-A62, features the following:
■two rows of 6 RJ-45 ports
■gigabit ports that support speeds of 10/100/1000 Mbps
■status LEDs
■two 16MByte DDR-SDRAM for packet buffering
■cable fault detection and distance-to-fault diagnostics are available for RJ-45
Ethernet ports (see the Test Facility chapter in the Software Reference for the
switch)
Front view AT-A62
The following LEDs report operations on AT-A62 expansion modules.
LED State Description
L/A
(Link Activity)
Green A 1000Mbps link has been established.
Green flashing 1000Mbps activity is occurring.
Amber A 10/100Mbps link has been established.
Amber flashing 10/100Mbps activity is occurring.
D/C
(Duplex/
Collision)
Green The port is operating in full duplex mode.
Amber The port is operating in half duplex mode.
Amber flashing Collisions are occurring.
AT-A62
1 2 3 4 5 6 7 8 9 10 11 12
L/A D/C D/C
FULL DUP HALF DUP COLACT
L/A
LINK 1000M ACT LINK 10/100M
L/A
L/A D/C

AT-9900s Series Switch Expansion Modules
10
Installation Procedure
Before you begin:
■Unpack the expansion module.
In an anti-static environment, remove the expansion module from its packing
material. Be sure to observe ESD precautions.
Caution Failure to observe proper anti-static procedures may damage the
unit. If you are unsure about correct procedures, contact your authorised
Allied Telesyn distributor or reseller.
■Verify the package contents if you have not already done so.
See “Package Contents” on page 4. If any items are damaged or missing,
contact your authorised distributor or reseller.
■Read the safety information for the switch.
Safety information is available in the Installation and Safety Guide that is on
the CD-ROM for the AT-9900s switch. Or you can download this document
from www.alliedtelesyn.co.nz/documentation.
■Gather necessary tools.
You may need a Phillips #2 screwdriver to adjust the retaining screws on a
blank faceplate.
Procedure
If you want to swap expansion modules, first save your configuration file as
necessary (create config and set config commands).
1. If connected, disconnect the switch from its redundant power supply.
2. Disconnect the switch from its AC or DC power supply.
3. Loosen the thumbscrews to the faceplate or existing expansion module,
and remove it.
Keep the faceplate for future use. If you remove the expansion module,
cover the bay with the faceplate to prevent dust and debris from entering it
and to maintain proper airflow.
4. Carefully slide the module into the empty bay until you feel it engage the
rear plug.