ALONET AL-WPC8 User manual

AL-WPC8
Programmable Control Panel
USER MANUAL
All Rights Reserved

AL-WPC8 - programmable control panel
Preface
Read this user manual carefully before using the product. Pictures are shown in this
manual for reference only. Different models and specifications are subject to real
product.
This manual is only for operation instruction, please contact the local distributor for
maintenance assistance. The functions described in this version were updated till April,
2018. In the constant effort to improve the product, we reserve the right to make
functions or parameters changes without notice or obligation. Please refer to the
dealers for the latest details.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. It has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a commercial
installation.
Operation of this equipment in a residential area is likely to cause interference, in which
case the user at their own expense will be required to take whatever measures may be
necessary to correct the interference
Any changes or modifications not expressly approved by the manufacture would void
the user’s authority to operate the equipment.
Trademarks
Product model and logo are trademarks. Any other trademarks mentioned in this
manual are acknowledged as the properties of the trademark owner. No part of this
publication may be copied or reproduced without the prior written consent.

AL-WPC8 - programmable control panel
SAFETY PRECAUTIONS
To ensure the best from the product, please read all instructions carefully before using
the device. Save this manual for further reference.
⚫Unpack the equipment carefully and save the original box and packing material for
possible future shipment.
⚫Follow basic safety precautions to reduce the risk of fire, electrical shock and injury
to persons.
⚫Do not dismantle the housing or modify the module. It may result in electrical shock
or burn.
⚫Using supplies or parts not meeting the products’ specifications may cause
damage, deterioration or malfunction.
⚫Refer all servicing to qualified service personnel.
⚫To prevent fire or shock hazard, do not expose the unit to rain, moisture or install
this product near water.
⚫Do not put any heavy items on the extension cable in case of extrusion.
⚫Do not remove the housing of the device as opening or removing housing may
expose you to dangerous voltage or other hazards.
⚫Install the device in a place with fine ventilation to avoid damage caused by
overheat.
⚫Keep the module away from liquids.
⚫Spillage into the housing may result in fire, electrical shock, or equipment damage.
If an object or liquid falls or spills on to the housing, unplug the module immediately.
⚫Do not twist or pull by force ends of the optical cable. It can cause malfunction.
⚫Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to
the device before cleaning.
⚫Unplug the power cord when left unused for a long period of time.
⚫Information on disposal for scrapped devices: do not burn or mix with general
household waste, please treat them as normal electrical wastes.

AL-WPC8 - programmable control panel
Table of Contents
1. Product Introduction....................................................................................................1
1.1 Features ............................................................................................................1
1.2 Package List ......................................................................................................1
1.3 Installation .........................................................................................................2
2. Panel Descriptions......................................................................................................3
2.1 Front Panel ........................................................................................................3
2.2 Side Panel .........................................................................................................4
2.3 Rear Panel.........................................................................................................4
3. Connection Introduction..............................................................................................6
3.1 System Diagram ................................................................................................6
3.2 Connection of Programming and Looping .........................................................7
4. System Operations .....................................................................................................9
4.1 USB Driver Installation.......................................................................................9
4.2 Software Programming......................................................................................9
4.2.1 Main Menu.............................................................................................10
4.2.2 Panel/Key setting...................................................................................12
4.2.3 Action list ...............................................................................................15
4.2.4 Event setting..........................................................................................15
4.2.5 Event List...............................................................................................24
5. Specification .............................................................................................................25
6. Panel Drawing ..........................................................................................................26
7. Troubleshooting & Maintenance ...............................................................................27
8. Customer Service .....................................................................................................28

AL-WPC8 - programmable control panel
1
1. Product Introduction
The AL-WPC8 is a Wall Control Panel. Every button is programmable and works either
individually or together. The AL-WPC8 is built in the programmable 3 RS232, 1 RS485,
3 Infrared & 2 Relay, and 1 mini USB for programming.
Please notice, RS232 (1) and IR2 share the same port, cannot be used at the same
time. Also, RS232 (2) and IR3 share the same port, cannot be used at the same time.
It can fully control our product, as well as third party devices such as projectors,
screens etc. It is an easy-to-use control device for presentation show rooms,
classrooms and boardrooms.
1.1 Features
⚫Every button can be programmed to send the bi-direction RS232 and RS485
commands simultaneously to control third party devices.
⚫Every button can be programmed to send the infrared code, control the relay, to let
them work simultaneously to control the third party devices.
⚫Every button is built in the infrared code and RS232 code learning function, and
baud-rate setting.
⚫ID looping function. 99pcs programmable control panels can be looped and
controlled together, by ID identifying.
⚫Programmed by USB or RS232, working with the PC software (PS-WP).
⚫Crystal and backlit buttons with easy user-friendly customizable changeable labels.
⚫The backlit brightness is controllable.
⚫Dimension: 11.4cm long and 7cm wide.
1.2 Package List
⚫1 x Programmable Control Panel
⚫1 x Power Adapter (DC 12V)
⚫3 x 2-pin Captive Screw Connector
⚫2 x IR Emitter
⚫8 x Button Caps
⚫1 x Button Label
⚫1 x USB Converting Cable
⚫1 x User Manual
Note: Please contact your distributor immediately if any damage or defect in the
components is found.

AL-WPC8 - programmable control panel
2
1.3 Installation
Follow the steps to install the device:
Firstly, dig a hole on the desk to the size marked on the aperture paper (shown in
Figure 1-1).
Secondly, put the device into the hole and adjust it to flush with the table (shown in
Figure 1-2).
Then, plug a set screw into the fixing mounting and screw the nuts tightly.
Figure 1- 1 Aperture paper
Figure 1- 2 Installation Guide

AL-WPC8 - programmable control panel
3
2. Panel Descriptions
2.1 Front Panel
Crystal and luminescent, programmable buttons:
Every button can be programmable with the software PS-WP.
Connect the PC via USB or RS232.
And every label inside the button can be changeable. You can choose the label you
need and change it very easily like below:
(For the specific transparent paper table, please contact the local distributor or reseller
for it)

AL-WPC8 - programmable control panel
4
2.2 Side Panel
2.3 Rear Panel
The AL-WPC8 panel has various ports in the rear panel, including Lopping port, RS232
port, RS485 port, IR port, Relay port and Power port. Below is the introduction:
①This port includes two parts:
One part is RS232 (2)/IR3, it can be used for control other devices or looping output.
Note: When use this USB port to program the control panel’s buttons, the
available COM port number should not be more than 10.
Mini USB Connector:
1.
Communicate with PC
which uses PS-WP to
program the buttons.
2. Transmit the infrared
data when learning IR
(Optional).
Infrared sensor port:
receive and learn the IR
code, to build the IR
database.

AL-WPC8 - programmable control panel
5
RS232 (2) and IR3 share the same port, the detailed use depends on the setting of
PS-WP.
Other part is RS232 (3), it can be used for control other devices or looping output,
or connect with PC.
These two parts share the same grounding.
②This port includes: RS232 (1)/IR2, IR1 and RS485.
a) RS232 (1)/IR2: share the same port, the detailed use depends on the setting of
PS-WP. When be used as RS232, it is unidirectional transmission, transmit data
but without receive.
b) IR1: for control other devices, it can be programmable by the PS-WP.
c) RS485: the RS485 can be programmed as different commands and control the
device with RS485 port. The command of RS485 is the same as RS232 (1).
③Low-Voltage relay ports: set the relay on/off by software PS-WP.
④Power connector: 12VDC. Be sure that the “+” and “-” never be mixed or
wrong connection.

AL-WPC8 - programmable control panel
6
3. Connection Introduction
3.1 System Diagram
The AL-WPC8 can active different ports at one time. It means every button can send
the RS232 and RS485 commands, IR code and control the relay at the same time. The
demo system diagram as below: