Bosch Solution 2000 User manual

Control Panel
Solution 2000 / 3000
en Installation Guide

Table of contents
1Introduction 9
1.1 About documentation 9
1.2 Bosch Security Systems, Inc. product manufacturing dates 9
2System Overview 11
2.1 Product Matrix 11
2.2 Configuration and Parts 11
2.2.1 Control panel capacities 11
2.2.2 Parts list 12
2.2.3 Order separately 12
3Installation workflow 13
4Accessories 14
4.1 Codepads 14
4.1.1 Installer Menu 16
4.2 WE800EV2 receiver 18
4.3 HCT-4 keyfob 19
4.4 RADION receiver B810 19
4.5 RADION keyfobs 19
4.6 RADION repeater 20
4.7 RADION detectors 20
4.8 B308 Octo-output Module 20
4.9 B426/B426-M Conettix Ethernet Communication Modules 21
4.10 B450/B450-M Conettix Plug-in Communicator Interfaces 21
4.11 A-Link Plus Software 22
4.12 Remote Security Control 23
4.13 Remote Security Control Plus 23
4.14 Keyswitches 23
4.15 TF008 Plug Pack (TF008-B) 24
4.15.1 Install the transformer 24
4.16 DLA 24
5Configuration 25
5.1 Installer Commands 25
5.1.1 Command 958 - Exit from Installer's Programming Mode without saving changes 25
5.1.2 Command 959 - Test IUI-SOL-ADAPTER 25
5.1.3 Command 960 - Save and exit from Installer's Programming Mode 26
5.1.4 Command 961 - Reset the Control Panel to Factory Default Settings 26
5.1.5 Command 962 - Copy the Control Panel Memory to IUI-SOL-ADAPTER 26
5.1.6 Command 963 - Copy IUI-SOL-ADAPTER data to the Control Panel 27
5.1.7 Command 965 - Set up Domestic Dialing Format 27
5.1.8 Command 966 - Enable/Disable the Automatic Stepping of Locations 28
5.1.9 Command 999 - Display the Control Panel Firmware Version Number 28
5.2 Disable Factory Defaults 29
6System Operations 31
6.1 Arming the system in AWAY Mode 31
6.2 Disarming the system from AWAY Mode 31
6.3 Arming the System in STAY Mode 1 32
6.4 Disarming the system from STAY Mode 1 33
6.5 Arming the system from STAY Mode 2 33
Control Panel Table of Contents | en 3
Bosch Security Systems, Inc. Installation Guide 2017.10 | 03 | F.01U.298.026

6.6 Disarming the system from STAY Mode 2 34
6.7 Codepad duress alarm 34
6.8 Codepad panic alarm 34
6.9 Codepad fire alarm 35
6.10 Codepad medical alarm 35
6.11 Isolating zones 35
6.11.1 Standard isolating 35
6.11.2 Code to isolate 36
6.12 Fault analysis mode 36
6.13 Fault descriptions 37
6.14 Inquire cloud status 39
7System Functions 41
7.1 Installer Code Functions 41
7.1.1 Add or Delete RF Wireless Devices 41
7.1.2 Add/Delete RF Repeater 42
7.1.3 Add/Delete RF Keyfob 43
7.1.4 Set the Number of Days until the First Test Report 45
7.1.5 Change Domestic Phone Numbers 45
7.1.6 Change Telco Arm/Disarm Sequence 46
7.1.7 Setting STAY Mode 2 Bypass Zones 47
7.1.8 Turning Report Monitor Mode On and Off 48
7.1.9 Walk Test Mode 49
7.1.10 Event Memory Recall Mode 49
7.1.11 AWAY/STAY 1 Arm/Disarm 50
7.2 Master Code Functions 51
7.2.1 Arm or Disarm both Areas at the Same Time 51
7.2.2 Arm or Disarm Single Area 51
7.2.3 Changing and Deleting User Codes 52
7.2.4 Adding Remote Radio User Codes 53
7.2.5 Deleting User/Radio Codes 53
7.2.6 Change Domestic Phone Numbers 54
7.2.7 Change Telco Arm/Disarm Sequence 54
7.2.8 Setting STAY Mode 2 Bypass Zone 54
7.2.9 Turning Outputs On and Off 54
7.2.10 Setting the Date and Time 55
7.2.11 Walk Test Mode 55
7.2.12 Event Memory Recall Mode 55
7.2.13 System reset 55
7.3 User Code Functions 55
7.3.1 Arm or Disarm both Areas at the Same Time 55
7.3.2 Arm or Disarm Single Area 56
7.4 Hold-Down Functions 56
7.4.1 Arm the System in AWAY Mode 56
7.4.2 Arm the System in STAY Mode 1 56
7.4.3 Arm the System in STAY Mode 2 56
7.4.4 Horn Speaker Test 57
7.4.5 Bell Test 57
7.4.6 Strobe Test 57
7.4.7 Turning Day Alarm On and Off 57
4en | Table of Contents Control Panel
2017.10 | 03 | F.01U.298.026 Installation Guide Bosch Security Systems, Inc.

7.4.8 Fault Analysis Mode 57
7.4.9 Initiate a Modem Call 57
7.4.10 Reset Latching Outputs 58
7.4.11 Change the Codepad Buzzer Tone 58
7.4.12 Send Test Report 58
8RF Keyfob Operations 59
8.1 Indications from RF Keyfob Operations 59
8.2 Remote Radio User Code Priority Levels 59
9Remote Arming by Telephone 60
10 A-Link Plus Application 61
10.1 Modem Connection 61
10.1.1 Remote Connection with Customer Control 61
10.1.2 Remote Connection without Callback Verification 61
10.1.3 Remote Connection with Callback Verification 62
10.1.4 Answering Machine Bypass Connection 62
10.2 Network Connection 62
10.3 Direct Connection 63
10.4 Options 63
10.5 Configuring for email 64
10.5.1 Configure through B426/B426-M 64
10.5.2 Configure through B450/B450-M 66
11 Communication Information 68
11.1 Primary Telephone Number for Receivers 69
11.2 Secondary Telephone Number for Receivers 69
11.3 Transmission Format for Receivers 69
11.4 Subscriber ID Number for Receivers 70
11.5 IP Items for Receivers 70
11.6 Conettix Items for Receivers 71
11.7 External Network Modules 72
11.8 Network Module Cloud Connection 73
11.9 Password for A-Link Connection 73
11.10 DTMF Timing Compensation 73
11.11 Country Codes 73
11.12 Telco Arming Sequence 73
11.13 Telco Disarming Sequence 74
11.14 Call Back Telephone Number 75
11.15 Ring Count 75
11.16 Telephone Line Fail Options 76
11.17 Communication Options 1 77
11.18 Communication Options 2 77
11.19 Communication Options 3 78
11.20 A-Link Plus Options 79
11.21 Domestic Dialing 79
11.21.1 Domestic Dialing Funtion 79
11.21.2 Setting Up and Programming Domestic Reporting 80
11.22 Reporting Formats 81
11.22.1 Contact ID Format 81
11.22.2 SIA Format 82
11.22.3 System Reporting List 82
Control Panel Table of Contents | en 5
Bosch Security Systems, Inc. Installation Guide 2017.10 | 03 | F.01U.298.026

12 Access 87
12.1 Installer Code 87
12.2 User Codes 87
12.3 User Code Priority 89
13 Zone Information 91
13.1 Day Alarm Information 91
13.1.1 Day Alarm Resetting 91
13.1.2 Day Alarm Latching 91
13.1.3 Day Alarm Operation 91
13.2 EOL Resistor Value 92
13.3 Zone Programming 93
13.3.1 Zone Defaults 93
13.3.2 Zone Types 97
13.3.3 Zone Pulse Count 99
13.3.4 Zone Pulse Count Time 100
13.3.5 Zone Options 1 100
13.3.6 Zone Options 2 101
13.3.7 Zone Report Options 102
13.3.8 Keyswitch Zone Options 103
13.3.9 Zone Source 104
13.4 Swinger Shutdown Count for Siren 104
13.5 Swinger Shutdown Count for Report 105
13.6 STAY Mode 2 Automatically Bypass Zones 106
13.7 Zone Status Reporting Options 106
14 RF Information 107
14.1 RF Supervision Time 107
14.2 Anti-Jamming Sensitivity 107
14.3 RF Receiver 108
14.4 RF Options 108
14.5 RFID 108
14.5.1 RF Keyfob RFID 109
14.5.2 RF Device RFID 109
14.5.3 RF Reapter RFID 110
15 System Reporting Information 111
15.1 Arm/Disarm Reporting Options 111
15.2 Codepad Reporting Options 111
15.3 Access Denied 111
15.4 System Status Reporting Options 112
15.5 Test Reporting Time 112
15.6 Test Reporting Options 113
15.7 Reports 113
15.7.1 Zone Tamper Report 113
15.7.2 Walk Test Report 113
15.7.3 Bypass Report 113
15.7.4 Trouble Report 113
15.7.5 Sensor Watch Report 114
15.7.6 Alarm Restore Code 114
15.7.7 RF Receiver Trouble Report 114
15.7.8 RF Receiver Trouble Restore Report 114
6en | Table of Contents Control Panel
2017.10 | 03 | F.01U.298.026 Installation Guide Bosch Security Systems, Inc.

15.7.9 RF Low Battery Report 114
15.7.10 Arm/Disarm Reports 114
15.7.11 Codepad Duress Report 115
15.7.12 Codepad Panic Report 115
15.7.13 Codepad Fire Report 115
15.7.14 Codepad Medical Report 115
15.7.15 AUX Power Supply Fail Report 115
15.7.16 AUX Power Supply Fail Restore Report 115
15.7.17 AC Fail Report 116
15.7.18 AC Fail Restore Report 116
15.7.19 Low Battery Report 116
15.7.20 Low Battery Restore Report 116
16 Programmable Outputs 117
16.1 Output Programming 117
16.2 B228 Output Mode 123
16.3 Output Event Types 123
16.4 Output Polarity 130
16.5 Output Timing 132
16.6 Pulsing Polarities 132
16.7 One-Shot Polarities 132
17 System Event Timers 134
17.1 Programming Entry/Exit Times 134
17.2 Entry Time 1 134
17.3 Entry Time 2 134
17.4 Exit Time 134
17.5 Entry Guard Time for STAY Mode 135
17.6 Delay Alarm Reporting Time 135
17.7 Sensor Watch Time 135
17.8 Codepad Lockout Time 136
17.9 Siren Run Time 136
17.10 Siren Sound Rate 136
17.11 Auto Arming Pre-Alert Time 136
17.12 Auto Arming Time 137
17.13 Auto Disarming Time 137
17.14 Kiss-Off Wait Time 137
17.15 Speaker Beep Volume 137
18 System and Consumer Options 138
18.1 System Options 1 138
18.2 System Options 2 139
18.3 System Options 3 139
18.4 System Options 4 140
18.5 System Option 5 141
18.6 Consumer Options 1 141
18.7 Consumer Options 2 142
18.8 Consumer Options 3 143
19 Partitioning 144
19.1 Programming 144
19.1.1 Partitioning Options 1 144
19.1.2 Partitioning Options 2 144
Control Panel Table of Contents | en 7
Bosch Security Systems, Inc. Installation Guide 2017.10 | 03 | F.01U.298.026

19.2 Partition Allocations 145
19.2.1 Zone Area Assignments 145
19.2.2 Codepad assignment 146
19.2.3 User code area assignments 146
20 Text Information 148
8en | Table of Contents Control Panel
2017.10 | 03 | F.01U.298.026 Installation Guide Bosch Security Systems, Inc.

Introduction
This section includes an introduction to documents for this product and other document-
related instructions.
About documentation
This document contains instructions for a trained installer to properly install, configure, and
operate this control panel, and all optional peripheral devices. Review this document before
beginning the installation to determine the hardware and wiring requirements for the features
used.
Throughout this document, the words “control panel ” refer to all control panels covered by
this document (Solution 2000/3000).
Notifications
This document uses Notices, Cautions, and Warnings to draw your attention to important
information.
Notice!
These include important notes for successful operation and programming of equipment, or
indicate a risk of damage to the equipment or environment.
!
Caution!
These indicate a hazardous situation which, if not avoided, could result in minor or moderate
injury.
!
Warning!
These indicate a hazardous situation which, if not avoided, could result in death or serious
injury.
Copyright
This document is the intellectual property of Bosch Security Systems, Inc. and is protected by
copyright. All rights reserved.
Trademarks
All hardware and software product names used in this document are likely to be registered
trademarks and must be treated accordingly.
Bosch Security Systems, Inc. product manufacturing dates
Use the serial number located on the product label and refer to the Bosch Security Systems,
Inc. website at http://www.boschsecurity.com/datecodes/.
The following image shows an example of a product label and highlights where to find the
manufacturing date within the serial number.
1
1.1
1.2
Control Panel Introduction | en 9
Bosch Security Systems, Inc. Installation Guide 2017.10 | 03 | F.01U.298.026

10 en | Introduction Control Panel
2017.10 | 03 | F.01U.298.026 Installation Guide Bosch Security Systems, Inc.

System Overview
Product Matrix
Figure 2.1: Product Matrix 2017
Configuration and Parts
This section lists each control panel's capacities and a parts list.
Control panel capacities
Features Solution 2000 Solution 3000
Number of users 32 32
Number of zones 4+4 (ZD) 8+8 (ZD)
Number of areas/partitions 2 2
Number of on-board outputs 4 4
Number of codepads 4 4
Number of B308 Octo-output modules 2 2
Number of B426 IP communicators 2 2
Number of B442 or B450 GPRS communicators 2 2
Number of WE800EV2 receivers 1 1
2
2.1
2.2
2.2.1
Control Panel System Overview | en 11
Bosch Security Systems, Inc. Installation Guide 2017.10 | 03 | F.01U.298.026

Features Solution 2000 Solution 3000
Number of RADION receivers 0 1
Number of RADION repeaters 0 8
Parts list
Control panels ship assembled from the factory with the following parts:
Literature
–Control Panels (Solution 2000 / Solution 3000 ) Quick Reference Guide
–Control Panels (Solution 2000 / Solution 3000 ) User Guide
HW pack
– EOL resistors
– Battery wires
– PSTN lead
– Screws
Assembly
– PC board
Order separately
Order the accessories listed below to aid in the installation of your control panel. If you
ordered your control panel in a kit, you might already have these parts.
Accessory Type Solution 2000 Solution 3000
Codepads Touchscreen, IUI-SOL-
ICON, IUI-SOL-TEXT
Touchscreen, IUI-SOL-
ICON, IUI-SOL-TEXT
Keyfobs HCT-4 HCT-4, RFKF-TB/RFKF-FB
Octo-output modules B308 B308
Receivers WE800EV2 WE800EV2, B810
Repeaters RFRP
Detectors Wired detectors Wired detectors, RADION
wireless detectors
Software A-Link Plus A-Link Plus
Ethernet communication modules B426 B426
GPRS communication modules B450 with B442 or B443 B450 with B442 or B443
Transformer TF008-B TF008-B
Other accessories:
Keyswitches
Battery
Siren
Strobe
RJ11 PSTN terminal
Control Panel Enclosure
2.2.2
2.2.3
12 en | System Overview Control Panel
2017.10 | 03 | F.01U.298.026 Installation Guide Bosch Security Systems, Inc.

Installation workflow
Before installing and operating the control panel, read these instructions. Failure to follow
these procedures may cause the device not to function properly. Bosch Security Systems Inc.
is not responsible for any devices that are improperly installed, tested, or maintained.
This document does not contain special information about local requirements and safety
issues. Information on such issues is provided only to the extent that it is needed for
operation of the device. Ensure that you are familiar with all safety-related processes and
regulations in your area. This also includes how to act in the event of an alarm and the initial
steps to take if a fire breaks out. The operating instructions should always be available on site.
It is a required part of the system and must be given to the new owner if the system is ever
sold.
Use the workflow and checkboxes below as you complete steps.
Install the enclosure
Install the control panel
Install and wire for telephone communication
Install and wire for IP communications
Install and wire the transformer
Install and wire arming devices
Install and wire outputs
Install and wire inputs
Complete the installation
See also
–Install the transformer, page 24
–Communication Information, page 68
–B426/B426-M Conettix Ethernet Communication Modules, page 21
–B450/B450-M Conettix Plug-in Communicator Interfaces, page 21
–Codepads, page 14
–RADION keyfobs, page 19
–Keyswitches, page 23
–WE800EV2 receiver, page 18
–B308 Octo-output Module, page 20
3
Control Panel Installation workflow | en 13
Bosch Security Systems, Inc. Installation Guide 2017.10 | 03 | F.01U.298.026

Accessories
Bosch Security Systems, Inc. manufactures a number of accessories that can be used in
conjunction with the control panel. These devices enhance certain features to make the
system extremely flexible.
Some sections include basic installation instructions. For detailed installation instructions,
refer to the Installation Guide that came packaged with the device.
Codepads
The Solution 2000/3000 control panels support two types of codepads: an alphanumeric LCD
codepad (IUI-SOL-TEXT) and an icon LCD codepad (IUI-SOL-ICON).
IUI – SOL -TEXT IUI – SOL – ICON
1 2 3
4
7
#
8
0
9
5 6
*
1
4
7
2
5
8
3
6
9
STAY # AWAY
0
*
1 2 3 4 5 6 7 8
ON
OFF
Installation
Set the address switches for the proper address, mount the mounting plate, wire to the
control panel, and attach the codepad to the mounting plate.
Notice!
Do not remove the spring from the tamper switch on the IUI-SOL-ICON. Removing the spring
will cause a Codepad Tamper Trouble and a report will be sent if configured to do so.
Set the address
The IUI-SOL-TEXT and IUI-SOL-ICON have 6 DIP switches that support SDI2 addresses 01 to
16. DIP switches determine the address for the codepad. The control panel uses the address
for communications. Use a ballpoint pen to set the switches.
4
4.1
14 en | Accessories Control Panel
2017.10 | 03 | F.01U.298.026 Installation Guide Bosch Security Systems, Inc.

If multiple codepads reside on the same system, each codepad must have a unique address.
The Solution 2000/3000 control panels support up to 4 codepads, addresses 01-04. DIP
switch address settings greater than 4 prevent the codepad from processing messages
received on the SDI2 bus and the option bus. Any change to the DIP switch requires a power
cycle or software reboot of the module for the new external address to be read.
DIP Switch Codepad
Address
DIP Switch Number
1 2 3 4 5 6
1 On Off Off Off Off On
2 Off On Off Off Off On
3 On On Off Off Off On
4 Off Off On Off Off On
Table 4.1: Codepad DIP switch address settings
Install the module
1. Use the provided anchors and screws to mount the codepad base on the wall.
2. Pull the necessary wiring through the mounting plate.
Wire to the control panel
Wire the codepad to the control panel using the control panel terminals labeled R, Y, G, B
(PWR, A, B, COM). Connect them to the codepad terminals labeled R, Y, G, B. Connect
codepads to the SDI2 data bus by parallel wire run from the control panel to each codepad,
wire from codepad to codepad, or a combination of the two. Use a maximum of 7500 ft (2286
m) of 22 AWG (0.8 mm) wire for all devices connected to the SDI2 bus combined.
1
2
3
R Y G B
1
+ -
BATTERY
PWR A B COM
R Y G B
PWR A B COM
PWR A B COM
Control Panel Accessories | en 15
Bosch Security Systems, Inc. Installation Guide 2017.10 | 03 | F.01U.298.026

Callout - Description
1 – Control panel
2 – Terminal wiring
3 – Codepad’s wiring terminal block
Installer Menu
Use the menu tree below to program the control panel from the IUI-SOL-TEXT codepad. To
program the control panel from the IUI-SOL-ICON, use the programming address indicated in
brackets [ ] next to each command as shown in the Menu Tree.
Example:
To program Exit Time using the IUI-SOL-TEXT
Method 1: By Text Menu
1. Enter the Installer Code, followed by [-] or [#] key (for example, [1234#]),
2. Then press keys [3], [1], [3] to enter [Exit time] and program the exit time.
Method 2: By address programming
1. Enter the Installer Code, followed by [-] or [#] key (for example, [1234#]),
2. Press [8] [1] to enter address programming.
3. Press [470 #] to enter Exit Time address to program.
To program Exit Time using the IUI-SOL-ICON
Enter the Installer Code followed by [#] key, then press [470 #] to enter Exit Time address to
program.
4.1.1
16 en | Accessories Control Panel
2017.10 | 03 | F.01U.298.026 Installation Guide Bosch Security Systems, Inc.

.
Command
Installer
Passcode
Inquire
System
RF diagnose
Test
1
2
3
4
5
Event recall
Fault analysis
2
1
Cloud status
3
Day alarm2
Arm/disarm seq.
3
Report monitor
4
Modem call init.
5
Domestic phone
6
Version display
7
Factory default
8
RF zone1
RF Keyfob
2
RF Repeater
3
Horn speaker1
Bell test2
Strobe test
3
Walk test
4
Test report
5
Access
2
Installer code
Access retry
1
3
User allocate2
User authority
3
User property
4
System
Timer
Codepad
Arm/disarm
Fault
Wireless
System option 1
3
1
2
3
4
5
6
Entry time11
Entry time2
2
Exit time3
Entry guard time for STAY mode
4
Sensor watch time
5
Codepad lockout time6
Auto arm pre-alert time
7
Auto arm time
8
Auto disarm time9
Silent codepad panic alarm1
Silent codepad fire alarm2
Silent codepad medical alarm3
Codepad access denied silent
4
Codepad fault beep enable
5
Codepad display off after 60s
6
Auto arm in STAY11
Single button arm enable
2
Single button disarm enable
3
Disarmed on power up
4
Arm/disarm track on power up
5
Phone remote arm
6
Answer machine bypass on arm
7
Ignore AC fail1
AC fail report wait time
2
Warning device fault monitor
3
Phone line fault indicator
4
Phone line fault alarm on armed
5
Phone line fault alarm on disarm
6
Lockout phone line fail alarm
7
RF receiver1
Zone RFID and input option
2
Keyfob RFID3
Repeater RFID
4
RF supervision time
5
RF jam sensitivity
6
RF RECE jam/tamper siren alarm
7
RFKF button4 arm in STAY1
8
RF arm/disarm strobe indicator
9
Home message1
Button factory default enable
2
Alarm memory reset on disarm
3
STAY indicator for day alarm
4
Digit 3 for codepad duress alarm
5
Siren and strobe output in STAY
6
Speaker beep volume
7
8Country code
[181]
[424]
[189]
[534]
[466]
[468]
[470]
[472]
[476]
[478]
[481]
[482]
[486]
[493.1]
[493.2]
[493.3]
[493.4]
[498.1]
[497.1]
[496.3]
[497.2]
[497.3]
[495.1]
[495.2]
[177.2]
[177.3]
[494.2]
[494.1]
[492.2]
[176.1]
[176.2]
[176.3]
[179.2]
Onboard tamper trigger alarm
8[495.3]
[395]
[1820]
[1500]
[1980]
[393]
[394]
[396.2]
[492.4]
[492.3]
[2500]
[900]
[497.4]
[496.4]
[498.2]
[498.3]
[491]
[112]
Domestic Dail Fail To Report1
Installer Arm/Disarm Function
2
System option 2
7[110.2]
[110.1]
Control Panel Accessories | en 17
Bosch Security Systems, Inc. Installation Guide 2017.10 | 03 | F.01U.298.026

Zone
Zone config
Installer
Passcode
Zone allocate
Zone name
Day alarm zone
STAY2 zone
EOL resistor
Zone state report
4
1
2
3
4
5
6
7
Siren swing shutdown count1
Report swing shutdown count
2
Telco arming sequence
1
Telco disarming sequence
2
Delay alarm report time
3
Kiss-off wait time
4
Delay siren until transmit over
5
Extend wait for handshake
6
Upload/download enable
7
Callback phone number request
8
Callback phone number
9
Siren run time
1
Siren sound rate
2
Siren sound on RF receiver fail
3
Silent zone tamper alarm1
Unseal RF zone that failed monitor
2
Bosch Smart Lockout enable
3
Zone pulse count handover enable
4
Handover delay in order
5
Area
5Codepad area
Area option
1
2
Output
6
STAY mode arm/disarm report enable1
Arm/disarm report only if alarmed2
First disarm/last arm report3
Arm/disarm report option
4
Codepad report option
5
Test report time and interval
6
Test report only when armed
7
Test report on siren reset
8
Test report option
9
First phone number1
Second phone number2
Transmit format
3
Subscriber ID number
4
IP + Port / Email
Conettix ACK wait time
Conettix heart beat time
Conettix anti-replay enable
5
CSVIP user name and password
6
Ring count1
Report function enable
2
Exit A-Link connection on alarm
3
System status report option
4
Use bell-103 for FSK format5
DTMF dial pulse to 1 digit/sec
6
Set up domestic dialing format
DTMF timing compensation [111]
7
Swing shutdown
8
Zone option
9
Arm/disarm all areas once1
Reset siren from any area2
Onboard output
Codepad output
Extend output
Siren config
1
2
3
4
Comm
7Receiver config
Network config
Report config
Comm option 1
Comm option 2
1
2
3
4
5
Network module1
A-Link/RSC password
2
Parameter
8Address program
Address auto step
Adapter
1
2
3
Test adapter
1
Read adapter
2
Write adapter
3
[267]
[502]
[2536]
[265]
[381]
[266]
[392]
[379]
[380]
[498.4]
[396.3]
[492.1]
[494.3]
[494.4]
[501.2]
[500.3]
[518]
[436]
[460]
[646]
[177.4]
[0, 40, 1417, 1457]
[16, 56, 1433, 1473]
[33, 73, 1450, 1490]
[34, 74, 1451, 1491]
[1000, 1200, 2060, 2260]
[1100, 1300, 2160, 2360]
[1401, 1405, 1409, 1413]
[1403, 1407, 1411, 1415]
[1400]
[479]
[480]
[396.1]
[81,82]
[83]
[175]
[177.1]
[180.3]
[427]
[178.2]
[178.1]
[500.1]
[403]
[411]
[428, 434]
[496.1]
[496.2]
[435]
[179.1]
[*]
[474]
[490]
[178.3]
[178.4]
[180.1]
[180.2]
[159]
[113]
[143]
8
7
8
9
* Refer to Command 965 - Set up Domestic Dialing Format, page 27.
WE800EV2 receiver
The WE800EV2 is designed to provide a convenient ON/OFF control for the Solution
2000/3000 series control panel. Provision is also made for the control of up to two (2)
external devices via on-board relays.
Install the module
1. Remove the small knockout in the Solution 2000/3000 control panel for the antenna and
insert the supplied rubber grommet.
2. Install the WE800EV2 PCB in the control panel with the top of the PCB in the slot
provided at the top of the case and secure with the provided screw at the bottom of the
PCB.
3. Thread the antenna wire through the grommet into the “ANT” terminal.
Wire to the control panel
Connect the 3 pin plug to the jumper labeled WE800 on the control panel. Note that the
connector will only install one way. If the relays are to be used, a wire will need to be
connected from the +12V terminal on the WE800EV2 to a +12 terminal on the control panel.
4.2
18 en | Accessories Control Panel
2017.10 | 03 | F.01U.298.026 Installation Guide Bosch Security Systems, Inc.

Add/delete keyfobs
Notice!
When purchasing a WE800EV2 kit, the keyfobs supplied are already learned to the WE800EV2
with both relays set for momentary operation. If a different relay set-up is required, delete the
keyfobs, then add them back again.
To add keyfobs:
1. Press the Learn/Delete switch once. Note that the LED will flash rapidly.
2. Press the button on the keyfob to be learned that corresponds to the desired relay
function.
Button 1 – Both outputs momentary
Button 2 – Output 1 toggling. Output 2 momentary.
Button 3 – Output 2 toggling. Output 1 momentary.
Button 4 – Both outputs toggling
3. Repeat for additional keyfobs.
4. Press the Learn/Delete button when finished adding keyfobs to complete the process.
To delete keyfobs:
Press and hold the Learn/Delete switch. Note that the LED will light and then extinguish after
4 seconds. The EEPROM is now erased. Individual keyfob deletion is not possible.
HCT-4 keyfob
This Button Premium Keyfob can be used in conjunction with the WE800EV2 RF Receiver
to operate the system remotely.
It can remotely arm and disarm the system in AWAY Mode or STAY Mode 1 and can activate
remote Panic Alarms. It can also operate outputs such as garage doors, swimming pool
pumps, or outside lights.
RADION receiver B810
The B810 is a wireless receiver that connects RADION wireless peripherals such as the motion
detectors, keyfobs, panic buttons, repeaters, and more, to supported Bosch control panels
using the SDI2 Bus connection.
For more information, refer to the installation and operation manuals for this product.
RADION keyfobs
RADION keyfob allows you to arm or disarm the security system, or send a panic alarm. The
control panels support two RADION keyfob models, RFKF-FB and RFKF-TB, that communicate
with the control panel using the RADION receiver SD. On the four-button version, two option
buttons are user-defined to perform additional functions. To operate these buttons, simply
press and hold either button for at least one sec in order for the desired feature to work.
Panic alarm
The keyfob sends a panic code to your monitoring company if your security system is
programmed to do so. Press both the lock and unlock buttons simultaneously for more than
600 milliseconds to send a panic alarm.
LED indicator
The LED flashes to indicate a signal was sent to your security system.
4.3
4.4
4.5
Control Panel Accessories | en 19
Bosch Security Systems, Inc. Installation Guide 2017.10 | 03 | F.01U.298.026

RADION repeater
RADION repeater receives transmissions from RADION transmitters and re-transmits them to
improve transmitted message reliability and range for compatible transmitters and its
assigned compatible receiver.
For more information, refer to the installation and operation guides for this product.
RADION detectors
For more information regarding the sensors supported by the Solution 3000 control panel,
refer to the installation and operation manuals for the B810 wireless receiver.
See also
–Add or Delete RF Wireless Devices, page 41
B308 Octo-output Module
The B308 Octo-output Module is a supervised device that provides 8 programmable outputs
(Form C relays) and connects to control panels through the SDI2 bus. Each output provides
dry contact switching rated for a maximum of 1.0 A at 24 VDC. The outputs are accessed
through on-board screw terminal connections. The address switches are used to set the
module’s SDI2 address. Control panel programming determines each output’s response to
specific events. The B308 receives serial data from the control panel and activates outputs in
response to control panel conditions and settings. Outputs can be programmed for remote
control from a control panel codepad or computer (A-Link) or smartphone application (RSC).
Set the address
Two address switches determine the address for the B308 Octo-output Module. The control
panel uses the address for communications. Use a slotted screwdriver to set the two address
switches. Set the address switches per the control panel configuration.
The module’s address switches provide a tens and ones value for the module’s address. Set
the tens switch to 0 and the ones digit 1 for module 1 ; set the tens switch to 0 and the ones
digit 2 for module 2.
Notice!
The module reads the address switch setting only during power up. If you change the
switches after you apply power to the module, you must cycle the power to the module in
order for the new setting to be enabled.
Install the module
After you set the address switches for the proper address, install the module in the enclosure.
Mount the module into the enclosure’s 3-hole mounting pattern using the supplied mounting
screws and mounting bracket.
Notice!
Remove all power (AC and battery) before making any connections. Failure to do so might
result in personal injury and/or equipment damage.
Wire to the control panel
4.6
4.7
4.8
20 en | Accessories Control Panel
2017.10 | 03 | F.01U.298.026 Installation Guide Bosch Security Systems, Inc.