Alpha ESS M4856-P Operating and maintenance instructions

Quick Installation Manual
BATTERY MODULE
M4856-P

Battery pack (X 1) PE Protective bag ( X 1) Screw M5*10 (X 6)
Battery connector:
Positive power cable (x1)
Negative power cable (x1)
Battery communication
cable (X 1)
Screw package：
Expansion tube (X 10)
Expansion screw (X 10)
Gasket (X 10) Bracket (X 2)
M4856-P
Packing List
1 2 3 4 5 6
7 8 9 10 11
Hexagon nuts with flange
M5(X 10)
Corrugated pipe (x1) User manual (X 1)
Quick installation guide (X 1)
Cable tie (X 6)
12

1 3 6
Open The Package
Mounting Fixed Panel
Step3
Use a screwdriver to assemble the battery mounting brackets onto the battery back panel.
Step1
Note: The box must be placed in the direction of the label and only remove the
packaging in upwards direction. Removing the packaging in other directions is
wrong.
Disassemble Appearance Parts
Step2
Pull off the buckle located in
the middle of the bottom.
APull the top two guide rods
to remove the front panel.
B
Battery pack (X 1) Screw M5*10 (X 4) Bracket (X 2)

Drilling Hole
Step4
Step5
Insert the expansion tube into the drilled hole.
Insert the expansion screw through the gasket and
lock with a screwdriver.
Pull off the buckle located in the middle of the bottom.
Mounting Fixed Panel
Push the battery firmly against the wall and use a level to
confirm the position of the battery.
Please drill four holes (two on each side) directly on the
wall at the marking positions of the brackets with an impact
drill (bit φ 8.0mm, length 20cm) and the depth of each hole
should be about 7 cm.
195cm
90cm
650cm
Note：
1：Check installation space.
2：Pack the PE bag on the battery to block out the dust before drilling.
PE Protective bag ( X 1)
A
B
A
B
C
2
4 5
Screw package：
Expansion tube (X 4)
Expansion screw (X 4) Gasket (X 4)

The waterproof connector is rotated counterclockwise
according to the installation procedure to remove the plug.
1
Use a screwdriver to remove the maintenance cover
before wiring.
2
All air switchs are set to disconnect at the factory.Please
check before wiring.
3
The waterproof joint seal should be
confirmed whether it is inserted into
the plastic claw ring during installation.
4
Wiring
Step6
Battery power cable connection sequence:
Go through the waterproof cap→ go through the sealing ring→ go
through the joint, fixed to the copper bar with M5 nut inside of the
battery.
Battery power cable connection sequence:
Go through the waterproof cap→ go through the sealing ring→ go
through the joint, fixed to the copper bar with M5 nut inside of the
battery.
7 8 9
Battery connector:
Positive power cable (x1)
Negative power cable (x1) Battery communication
cable (X 1)
Hexagon nuts with flange
M5(X 10)
10 11
Corrugated pipe (x1) Cable tie (X 6)

Step10 Step11
Confirm that the battery closest to the inverter is
number 1 battery and so on. The maximum
number of parallel batteries is 6.
The direction of the last DIP switch of the battery
is configured according to the black mark
position of the No. 6 figure, that is, the last
battery dial switch 2 is up and the other battery
dial switches are all down.
When the number of batteries is between 2 and
6 sets, the dial switch configuration is operated
according to the sequence.
1
2
3
Positive power line wiring Negative power line wiring Connect Communication Line
Step7 Step8 Step9
DIP Switch Mounting Appearance Parts
Pull the top two guide rods into the housing.
Press the buckle from the middle of the bottom.
A
B
To INV To INV To INV
Communication board DIP switch configuration: The mode of disassembly of step 2 of restoration:

Alpha ESS Co., Ltd.
Headquarter: Alpha ESS Co., Ltd.
[phone]
[email protected]
www.alpha-ess.com
JiuHua Road 888, Nantong High-Tech Industrial
Development Zone, Nantong City, 226300
Germany: Alpha ESS Europe GmbH
+49 (0) 6103 / 459 160-1
[e-mail]
www.alpha-ess.de
Paul-Ehrlich-Straße 1a, 63225 Langen, Hessen
Australia: Alpha ESS Australia Pty. Ltd.
[phone] (Sales)
[phone] (Technical Support)
[email protected]
www.alpha-ess.com.au
Suite 1, Level 1, 530 Botany Road, Alexandria,
NSW, 2015
Italy: Alpha ESS Italy S.r.l.
[phone]
[email protected]
www.alpha-ess.it
Via Loda,17-41013 Castelfranco Emilia (MO)