Alpha ESS Smile5-BAT Operating and maintenance instructions

Quick Installation Manual
BATTERY MODULE
SMILE5-BAT
V02

SMILE5-BAT
Step1 Step2
Open the front panel and remove the right side communication baffle.
PACKING LIST
REMOVING WIRING BAFFLE
6 x M8*60
6 x M6 Gasket 2 x Power Cable
(1 black, 1 red)
1 x User Manual
1 x Quick Installation Manual
6 x M5*10 6 x M4*10 2 x Mounting Panel
Battery Communication Cable
Take out the battery from the packaging box.
+
-
For the new version battery,
there is no need to remove the
top cover in Step 3.

Step5
Assemble the battery mounting panel onto the battery.
Step6
Push the battery against the wall to drill holes on the wall with
an impact drill.
Step3
SECURING BATTERY
Step4
Connect the power cable at the top of the bottom battery and
close the battery front cover.
Unscrew the corner screws and remove the top cover of the battery.
+
-
2 x Power cable
For the new version
battery please connect
the power cables directly.
4 x M5*10 Screws
Cover the top of the
battery to block out
the dust.

INSTALLATION & WIRING
Step7 Step8
To install another battery repeat Step 1 ~7.
Step9
Connect the communication cable from the inverter to the battery.
Remove the debris baffle and secure the battery to the wall
with screws.
Step10
Connect the two batteries at the side. Lock all communication
baffles.
Connect batteries first if more
batteries are to be added.
4 x M8*60
4 x M8*60
1 x Communication cable
BAT1
BAT2

WIRING
Step13
DIP SWITCH
CONFIGURATION with SMILE5-INV
Step11
Connect the power cables from BAT2 to BAT1.
Step12
Connect the power cables from BAT1 to inverter.
Black - Black
Black - Black Red - Red
Red - Red
Then close the DIP baffle
and battery front panel.
You can add up to 6 extra
batteries with maximum two in
a string.
Only the battery farthest from the inverter
needs to set DIP.
Open the front panel of the farthest
battery from the inverter and remove
DIP baffle. Set the DIP switch 2 to “on”
mode.
Please install extra
batteries only by the
side if more are to
be added.
WEON
1 2 3 4

CONFIGURATION with GOODWE INVERTER
If there are two or more than two BAT, after connecting the
power cables, please refer to the following the steps:
GoodWe (EM, ES, SBP series)
The communication cable between INV and BAT is
not regular net cable, it should be as below:
1. If there is only one BAT, DIP switch of BAT should
be as below:
2. If there are two or more than two BAT, DIP switch
of BAT should be as below:
Battery
Position
one BAT
DIP 1
OFF OFFON ON
DIP 1 DIP 1 DIP 1 DIP
Switch
Battery
Position
other
BAT
Farthest
BAT
DIP 1
OFF
OFF OFF
OFF OFF
ON ON
ON
DIP 1 DIP 1 DIP 1 DIP
Switch
A. Only connect the communication cable between batteries at the
first. Turn on the batteries and they will get into standby mode
(green light flickering 1s).
B. Until batteries get into work mode (green light flickering 10s)
and then connect the communication cable between BAT and INV.
WEON
1 2 3 4
WEON
1 2 3 4
WEON
1 2 3 4

Alpha ESS Co., Ltd.
Headquarter: Alpha ESS Co., Ltd.
[phone]
[email protected]
www.alpha-ess.com
JiuHua Road 888, Nantong High-Tech Industrial
Development Zone, Nantong City, 226300
Germany: Alpha ESS Europe GmbH
+49 (0) 6103 / 459 160-1
[e-mail]
www.alpha-ess.de
Paul-Ehrlich-Straße 1a, 63225 Langen, Hessen
Australia: Alpha ESS Australia Pty. Ltd.
[phone] (Sales)
[phone] (Technical Support)
[email protected]
www.alpha-ess.com.au
Suite 1, Level 1, 530 Botany Road, Alexandria,
NSW, 2015
Italy: Alpha ESS Italy S.r.l.
[phone]
[email protected]
www.alpha-ess.it
Via Loda,17-41013 Castelfranco Emilia (MO)