Alpha420 EDIOVEN User manual

INSTRUCTION
MANUAL
EDIOVEN

TABLE OF CONTENTS
WELCOME
DECARB / ACTIVATION
INFUSION
BEST PRACTICES / TIPS
GETTING STARTED
CLEANING
SAFETY
WARRANTY
02.
02.
05.
06.
07.
09.
10.
11.

WELCOME
02.
Welcome to a world of new possibilities, easily make edibles in the
convenience of your kitchen.
Fully activate your herbs and then infuse into butter, oil, tincture, lotions
and more.
Add your infused base to virtually any recipe. Select the ingredients and
strength you prefer.
The EDIOVEN does the decarbing and infusing work for you. Make
incredible herbal infusions – mess and fuss free.
DECARBOXYLATION
Decarboxylation is the best science you will do in your kitchen. It’s the
perfect combination of time and temperature to activate your herbs,
now made easy with a touch of a button.
To get the maximum potency, you must decarb BEFORE infusing. If you
skip this step, your material will be WEAK and only approximately 25%
activated.
Why Decarb?

You can decarb any plant material such as flower, kief, stems, or sugar
leaf. Insert the silicone sleeve to decarb BHO wax, shatter, budder,
rosin, oil, etc.
What?
Approximately ½ ounce of plant material. Up to 1 ounce of
concentrates.
How much?
Approximately ½ ounce of plant material. Up to 1 ounce of
concentrates.
What Temperature should I decarb at?
Higher temps run the risk of damaging the terpenes, the special trace
floral oils. Get the maximum conversion with our recommended time
and temperatures.
Can I increase the temp to decarb faster?
Flower/Kief
Concentrate/Wax
240°F
240°F
for 1:10 (70 minutes)
for 0:45 min.
03.

DECARBING CONCENTRATE / WAX
04.
USE CAUTION:
EDIOVEN cup and chamber will be very HOT!
Wax is sticky and will bubble as it warms up.
Approximately half way thru the cycle, PAUSE the cycle and STIR your
concentrate to release the air bubbles.
Stir until the bubbles are gone.
To pause, press the Start / Pause Button.
When done stirring, press the Start Button again to resume and finish
the cycle.
NOTE: ALWAYS use the included silicon sleeve and glass
stir rod. Both are non-stick and easily cleanable.

Butter - If using butter or coconut oil, make sure it is melted first
before putting into the metal cup.
Infusing Concentrates / Waxes - We recommend pausing the
cycle half way through (approx. 20 minutes in) and stirring the
contents with the glass rod. Stirring helps release the gasses,
stir until it stops bubbling. Then press the Start Button to
resume cycle.
INFUSION
05.
Use enough oil, butter, or alcohol to cover your material.
How much?
Infuse butter, alcohol, coconut oil, olive oil, MCT oil, honey tea, coffee
and more.
What?
What Temperature Should I Infuse at? For How Long?
Oil
Butter
Tincture
180°F
180°F
160°F
for 1:30 (1½ Hrs)
for 2:00 (2 Hrs)
for 2:00 (2 Hrs)
Tips:

Start Small - If your new to decarboxylation or infusing, start small.
Anytime you try something new, a new oil or recipe, experiment
with small amounts.
Silicone Sleeve – For anything other than dry plant material, always
use the silicone sleeve inside the metal cup.
NEVER place your material directly in the machine. always use the
metal cup.
Loading - When loading herbs into the EDIOVEN, they should be
loose with room on the top. The material does not need to be
ground up. However, it should be broken into popcorn size chunks.
To Minimize Smell
Use at Room Temperature - For best results use when ambient
temperature is between 60- 80 degrees Fahrenheit.
TIPS / BEST PRACTICES
06.
Always use the silicon lid for the metal cup.
Secure the outer plastic lid and twist slightly to lock in
place.
Let the EDIOVEN cool down before opening the lid.
The hotter air is more fragrant.

Stuck Sleeve? If your sleeve is stuck, put it in the freezer for a few
minutes and it will come right out.
Let It Cool Down - The EDIOVEN should cool between each cycle,
approximately 15 minutes. The inner cup should be cool to the
touch before starting any new cycle.
To end a cycle, hold the Start / Pause button 5 seconds until it turns
green or just unplug it.
Get Ready/ Assemble – Place the silicon sleeve into the metal cup.
Then place metal cup into the EDIOVEN. Keep the silicone lid and
plastic top cover near by.
NOTE: Be sure the cup is COMPLETLY DRY
before placing in EDIOVEN.
Power - Plug into power outlet. The green light indicates it’s ready
for you to select your settings.
INSTRUCTIONS
01.
02.
07.

08.
Select Default or Customize Settings – When plugged in, the
preset setting appears:
To customize, simply press the time or temperature button and
then up or down buttons to your liking.
03.
04.
240°F 1:10 (70 minutes)
Status Light
Start / Pause / Stop
NOTE: Once the cycle starts, time or temperature
adjustments are not allowed.
NOTE: Only add what fits comfortably. Do not jam more in
as it may harm the trichomes. Leave room at the top
Add Material
Open the top of the EDIOVEN
Place your material in the metal removable cup/canister
a.
b.

09.
Add Silicon lid firmly
Add the Top Cover, securing with a slight twisting
c.
d.
Start Cycle – Press the Start button to start the cycle. The light
will change from green to red. The cycle has started.
05.
Cycle Complete – The EDIOVEN will go thru a series of beeps
when the cycle completes and finishes the cool down. The Status
Light will change to green when complete.
WAIT - Once the decarb cycle has finished, the inside will still be
hot. We recommend waiting 15 minutes for the metal cup to cool to
the touch.
Infusion - For infusion after decarbing, add your oil, butter or liquid
preference into the silicon sleeve.
06.
07.
08.
Cleanup - Once finished, let the EDIOVEN cool to the touch.
Remove the metal cup with sleeve. Separate and either hand wash
or place in the dishwasher.
09.
NOTE: Leave room on the top; do not fill past the top
of the silicon sleeve. Maximum is about 1 cup.
NOTE: The EDIOVEN machine itself should never get wet.
Fill the cup first and then gently insert it into the machine.

As with any electrical appliance, always follow standard safety
precautions.
10.
Only use this appliance for its intended use.
Read all instructions first before operating appliance.
Close supervision is needed when any appliance is used near
children.
Unplug the power cord when not in use or before cleaning.
Keep the power cable away from HOT surfaces to avoid damage.
Always use a 120V/60Hz power source. If you live in a country with
higher voltage you will need to purchase a Power Transformer to
step down to the correct voltage. A typical prong adapter will not
work. It needs to be a transform the local power into 120V/60Hz
for correct operation.
If anything unusual happens, unplug power supply.
Do not use if any part is broken, chipped, loose or cracked. Contact
us immediately at [email protected] for a replacement.
SAFETY
In a well-ventilated area inside, not outdoors.
On a flat surface.
Do not place on or near any hot burner or in a heated oven.
Where to use?

11.
For anything other than dry plant material, always use the silicone
sleeve inside the metal cup.
Do NOT touch hot surfaces. Machine & contents will be HOT during
and after use. Use a silicone glove or oven mitt.
All parts should be dry when inserted, including metal cannister
and silicon sleeve.
CAUTION:
WARRANTY
The Alpha420 EDIOVEN is guaranteed to be free from manufacturer
defects for 1 year from the date of original purchase. If there are prob-
lems due to manufacturing, we will replace or repair the unit.
This warranty only covers the original purchaser and does not cover
problems resulting from misuse, neglect, use for commercial purposes,
any use not conforming to manual directions. If the unit has been
altered or modified, warranty is null and void.
If you have a problem with your machine, contact us right away at
[email protected]. We may be able to quickly troubleshoot it and
get everything working correctly.

Alpha420
MFG# A420-EDVN-2C
Copyright 2022
All domestic and international rights reserved.
Designed in Detroit. Made in China.
THANK YOU FOR YOUR PURCHASE!
Questions & Comments?
[email protected]

SCAN TO JOIN THE PACK,
SEE RECIPES, & MORE