Alphawave Photonics AWCL-300-6P-Audio User manual

AWCL-300-6P-Audio RGB Controller
2011
Page 1
V.201111C3
AWCL-300-6P-Audio
3 channels audio synchronized RGB
3 channels audio synchronized RGB 3 channels audio synchronized RGB
3 channels audio synchronized RGB
Controller
Controller Controller
Controller
User’s Manual

AWCL-300-6P-Audio RGB Controller
2011
Page 2
V.201111C3
1. Introduction :
1.1 Features :
Support IR remote control interface.
R , G , B bright can be ad usted individually ,and auto-saving for the setting.
Built-in six LED dynamic programs , the dynamic of programs can be set for Fade/Jump
and dynamic speed.
Real Audio Synchronized color LED Control.
Automatically control made switched between Audio Synchronized modes with Silent
color fade mode.
Ad ustable Sensitivity for audio synchronized mode , offered Classic / Rock mode for
different styles sound.
 Audio source option for Line-in or Microphone.
 The maximum output is 4A x3 channels , that is 150W/12V or 300W/24V.
1.2Specifications
Operation Voltage DC10V~30V。
LED Output Power 150W/12V 或 300W/24V
LED Module Type Constant Voltage with constant current or
Constant voltage with limit voltage.
Max out current 4A/channel x 3channels
Weight 250g
Size L:110mm x W:70mm x H:23mm
Operation Temperature 0°C ~+70 °C
Storage Temperature -20°C ~ +85 °C

AWCL-300-6P-Audio RGB Controller
2011
Page 3
V.201111C3
2.User Guide
2.1 Input/Output interface
<The Upper side >
Power IN : The connector of LED power supply (for DC12~30V depends on the LED
module type).
V+ : The connector of LED power supply.
B : The connector of the Blue channel (cathode of Blue LED module).
G : The connector of the Green channel (cathode of Green LED module).
R : The connector of the Red LED (cathode of RGD LED module).
 : the microphone receiver .
DC IN : DC10~30V adapter input.
 : Sensitive control of sound source.
AUDIO IN :Audio Line-In connector .
 : Sound synchronized mode selection.
“ ” : Silence mode.
“ ” : Audio-In mode.
“ ” : Microphone In mode.

AWCL-300-6P-Audio RGB Controller
2011
Page 4
V.201111C3
Extension IR Receiver wire : The 50cm long extension wire of IR Receiver could be pull
out for using or storage in the case easily.
2.2Remote Control
Power Power On/Off
R, G, B, O, Y, I, W, P
Single color in static mode
=100% Red.
=100% Green.
=100% Blue.
Orange=100%Red+50% Green;

AWCL-300-6P-Audio RGB Controller
2011
Page 5
V.201111C3
Yellow=100%Red+100%Green;
Indigo=100%Green+100%Blue;
White=100%Red+100%Green+100%Blue;
Purple=100%Red+100%Blue.)
E
Start voice control function ; classical/rock mode switch.
( See the Bottom A-2 )
Speed+ /- P1~P6 Dynamic mode speeding or slower , total 25 degrees.
※
Brightness+/-
Ad ust the Brightness for Dynamic mode and static mode , total
17 degrees.※※
Pause Pause/Play button when Built-in program is running.
Fade/Jump Switching to Fade/Jump mode while Built-In program mode.
P1~P6 Programs Built-in color mixing 6 programs.
Choice one program then set in fade or ump mode.
P1
100%Red ->100%Red+100%Green ->100%Green
->100%Green+100%Blue ->100%Blue ->100%Red->repeat
P2
100%Red ->100%Red+50%Green ->100%Red+100%Green
->50%Red+100%Green ->100%Green ->100%Green+50%Blue
->100%Green+100%Blue ->50%Green+100%Blue ->100%Blue
->50%Red+100%Blue ->100%Red+100%Blue
->100%Red+50%Blue ->100% Red ->Repeat
P3
100%Red->100%Green ->100%Blue ->100%Green ->100%Red
->Repeat
P4
100%Red ->extinguish ->100%Red+100%Green ->extinguish
->100%Green ->extinguish ->100%Green+100%Blue
->extinguish ->100%Blue ->extinguish ->100%Red+100%Blue
->extinguish ->100%Red ->extinguish ->repeat
P5
100%Red ->100%Red+100%Green ->100%Green
->100%Green+100%Blue ->100%Red+100%Green+100%Blue
->100%Blue ->100%Red+100%Blue ->100%Red->Repeat

AWCL-300-6P-Audio RGB Controller
2011
Page 6
V.201111C3
P6
100%Red+100%Green ->extinguish ->100%Green+100%Blue
->extinguish ->100%Red+100%Blue –>extinguish ->repeat
R+/- Add/decrease red color in static mode。total 17 degrees。
※※
G+/-
Add/decrease green color in static mode。Total 17 degrees。 ※
※
B+/- Add/decrease blue color in static mode。Total 17 degrees。
※※
※：When using the remote controller
When using the remote controllerWhen using the remote controller
When using the remote controller ,
,,
, it will be the invalid instruction w
it will be the invalid instruction wit will be the invalid instruction w
it will be the invalid instruction when the buzzer beeps 3 steps
hen the buzzer beeps 3 stepshen the buzzer beeps 3 steps
hen the buzzer beeps 3 steps。
。。
。
※：the speeding degrees as follows :（ms）
1 2 3 4 5 6 7 8 9 10 11 12 13
0.064 0.128 0.256 0.512 0.768 1.024 1.536 2.048 3.072 4.096 5.12 7.168 8.192
14 115 16 17 18 19 20 21 22 23 24 25
10.24 12.288
15.36 20.48 32.768
40.96 49.152
65.536
81.92 102.4 147.46
204.8
※※：the 17 degrees of brightness as follows：(%)
1 2 3 4 5 6 7 8 9
0 6.25 12.5 18.7 25 31.25 37.5 43.74 50
10 11 12 13 14 15 16 17
56.25 62.5 68.75 75 81.25 87.5 93.75 100
note:
1. R+-/G+-/B+-: to mix the color you need to be in static mode.
2. P1~P6 color mixin pro rams : the SPEED and FADE/JUMP modes can be adjust .

AWCL-300-6P-Audio RGB Controller
2011
Page 7
V.201111C3
2.3 Application
. Connect WCL-300-6P- udio to LED lightings.
-1. Connect WCL-300-6P- udio with an udio player for sound control.
Please connect the Audio player with an Audio Amplifier and with an
AWCL-300-6P-Audio by AV terminal shunt.
Therefore, it will be easy to control the audio amplifier’s volume and won’t
influence the Line-in signal of AWCL-300-6P-Audio.
Please have below application chart for your reference:

AWCL-300-6P-Audio RGB Controller
2011
Page 8
V.201111C3
-2. dditional function of new version WCL-300-6P- UDIO：
：：
：
The sound control has two modes:
1: Classical mode （when press「 」key，beeps 1 step）: the lighting changes
in fade in/fade out style and slower , fit for classical music；
2: Rock mode （when press「 」key，beeps 2 steps）: the lighting changes in
ump mode and faster , fit for rock or dance music.

AWCL-300-6P-Audio RGB Controller
2011
Page 9
V.201111C3
B. Connect WCL-300-6P udio with a signal repeater ( WCL-300-R) for extension
connecting.
With voltage drops or consumption of AWCL-300-6P-Audio is full ; connect with
signal repeater AWCL-300-R by lighting strip or wires for extension connecting.
<AWCL-300-6P-Audio connects with the signal repeater by RG wires.>

AWCL-300-6P-Audio RGB Controller
2011
Page 10
V.201111C3
< AWCL-300-6P-Audio connect two repeaters by RG and RJ45 signal. >
※See AWCL-300-R manual for more detail