Alpine ALP411-V Quick start guide

1
VERTICAL
DIAPER
CHANGING
STATION
ALP411-V
OPERATION AND
INSTALLATION GUIDE

Known in the industry for excellent products, Alpine Industries is a manufacturer of
innovative, solution-based products for the commercial and institutional markets
worldwide. Combining commitment to the customer, design innovation and skilled,
dedicated workforces, they have produced a range of products that are an essential
part of every commercial facility. Every product is designed to the highest standards,
enabling you to get your requirements done in a reliable and cost-eective way.
THANK YOU
FOR YOUR
PURCHASE.

1 Important Safety Information
2 Parts List
3 Installation Instructions
9 Operation Instructions
10 Cleaning and Maintenance
11 Warranty
TABLE OF CONTENTS

1
• Failure to follow these warnings and the installation instructions
could result in serious injury or death.
• Read all instructions before installing diaper changing station.
Keep these instructions. DO NOT discard.
• A stud MUST be located and used for at least one side of the
diaper changing station.
• The diaper changing station is no stronger than the anchors or walls
to which they are attached and, therefore, MUST be firmly secured in
order to support the weight they are intended to support. Contact an
architect or building contractor if any questions.
• Child should never be left unattended.
• Avoid serious injury from falling or sliding out. Always use restraint
system.
• Adding excessive weight such as parcels, packages, or accessories
to the unit or to the bag hooks that exceed the total weight limit of
50 pounds (22.7 kg) may cause the unit to be unstable or may cause
a hazardous unstable condition to exist.
ADULT INSTALLATION REQUIRED.
READ ALL INSTRUCTIONS BEFORE ASSEMBLY
Unpack carton and identify all parts (See Parts List on left hand page.)
IMPORTANT SAFETY INFORMATION
A.D.A. COMPLIANCE
306.3 Knee Clearance, 307.2 Maximum Protruding Objects,
308.2 Forward Reach, 308.3 Side Reach, 309.4 Operation,
902.3 Work Surface Compliant when properly installed.
WARNING:
!
IMPORTANT SAFETY INFORMATION

2
306.3 Knee Clearance, 307.2 Maximum Protruding Objects,
308.2 Forward Reach, 308.3 Side Reach, 309.4 Operation,
902.3 Work Surface Compliant when properly installed.
PARTS LIST
3” WOOD SCREWS (4) 3” MACHINE SCREWS (2)
3/4” FINISHING
WASHERS (4)
3/4” FLAT WASHERS (4)
3/4” FLAT WASHERS (4)
TOGGLE ANCHORS (2)
DOOR/WALL PLATE
To be mounted on the
outside of the restroom door
FOR USE WITH WOOD STUDS FOR USE WITH TOGGLE ANCHORS
1 ¼” CAPS (6)

3
INSTALLATION INSTRUCTIONS
ADULT INSTALLATION REQUIRED.
TOOLS NEEDED:
• Level
• Measuring tape
• Power drill with 7/32”, 1/8”, and 1/2” masonry bits
• Power screwdriver with bull nose phillips bit
READ ALL INSTRUCTIONS BEFORE ASSEMBLY
Unpack carton and identify all parts (See Parts List on left hand page.)
1. Locate wood stud where left side of changing station will be mounted
to the wall.
2. Measure up 57.5’’ (146cm) from the floor and mark the wall. This locates
the position for the top left attachment hole.
NOTE: Mark on wall MUST be in center of wood stud.
3. Align hole in top left corner of changing station with mark on wall and
hold in place.
4. Using a level and measuring tape, mark the remaining three (3) holes.
After marking holes, set changing station down on ground.
5. Use a power drill and appropriate bit to drill four (4) holes in the wall.
This may require 2 people.
NOTE 1:
FOR WOOD STUDS:
- If finished wall surface is tile or masonry over wood studs,use a 7/32”
masonry bit for the pilot hole until you hit the wood stud, then change
to 1/8” bit.
- Use wood screws, finishing washers and flat washers (See Figure A
on Page 4).

4
FIGURE A
WALL
FLAT WASHER
WOOD
STUD
CHANGING
STATION BACK
INSTALLATION INSTRUCTIONS
WOOD SCREW
MOUNTING HOLE
FINISHING WASHER

5
INSTALLATION INSTRUCTIONS
NOTE 2:
FOR USE WITH TOGGLE ANCHORS:
- If finished wall surface has wood studs that are not 16” on center,
has metal studs, or has an underlying surface of concrete block, use
1/2” bit.
- Use machine screws and flat washers (See Figure B on Page 6).
- For holes NOT located in a wood stud, toggle anchors Must be used
(See Parts List on page 2). See “Using Toggle Anchors” section.
6. Align holes in changing station with drilled holes and secure top left
corner of changing station to wall stud using the appropriate screw and
washer. Continue to secure the three (3) remaining corners using the
appropriate screws and washers as described in NOTE 1 or NOTE 2.
7. Ensure all four (4) screws are tight and snap caps over screw heads.
ALL 4 OF THESE LOCATIONS
MUST BE USED FOR SAFE
INSTALLATION. THE LOWER HOLES
ENSURE INSTALLATION THROUGH
THE METAL BRACKETS.
WARNING
!

6
INSTALLATION INSTRUCTIONS
FIGURE B
WALL
FLAT WASHER
WOOD
STUD
CHANGING
STATION BACK
MACHINE
SCREW
TOGGLE ANCHOR

7
INSTALLATION INSTRUCTIONS
USING TOGGLE ANCHORS:
1. Insert metal end of toggle anchor into 1/2” hole.
2. Slide zip strip down snugly against wall.
3. Snap o break-away pieces of toggle anchor (See Figure C Below).
5. Ensure all four (4) screws are tight and snap caps over screw heads.
4. Align holes in changing station with toggle anchors and secure top
left corner of changing station to wall using machine screws and flat
washers. Continue to secure the three(3) remaining corners using
machine screws and flat washers.
ZIP STRIP
BREAK AWAY
PIECES
BREAK AWAY
PIECES
TOGGLE
ANCHOR
BEHIND
WALL
WALL
FIGURE C

8
INSTALLATION INSTRUCTIONS
RECOMMENDED BLOCKING
If the walls do not have studs on center, then additional blocking is
necessary (See Figure D below).
Contact an architect or building contractor to make sure the blocking
is adequate and complies with building codes.
FIGURE D
22-11/25”
570mm
16-1/2”
420mm

9
OPERATION INSTRUCTIONS
USING THE CHANGING STATION:
Rotate base downward. Place infant on top of the changing surface. Use
restraint system as described below. After child has been changed, remove
restraint system and rotate base back up against the wall.
USING RESTRAINT SYSTEM:
Place child so restraint strap is located at abdomen. Rotate top of buckle
upward and insert strap in buckle. Pull strap through buckle until snug
against infant. Rotate top of buckle downward to lock the strap into place.
Slide yellow locking tab over top of buckle (See Figure E below). Reverse
steps to loosen strap.

10
CLEANING AND MAINTENANCE
Check all hardware and components monthly or as required to ensure
hardware is tight and there are no missing or damaged components.
Take unit out of service if any component is missing or damaged and
contact customer service to order replacement parts. Do not substitute
parts. For replacement parts, contact customer service at:
[email protected]
Clean by using a damp cloth with mild soap or mild multi-purpose cleaner.
Do not use any strong chemical cleaners or cleaning agents that may be
hazardous to children. Slide yellow locking tab over top of buckle (See
Figure E below). Reverse steps to loosen strap.

11
LIMITED WARRANTY
Terms and conditions of the Alpine 1 year limited warranty—Your warranty begins at the date
of purchase, please retain your proof of purchase. The warranty coverage only covers the
original owner. The replacement of any port is warranted for the remainder of the original
warranty period.
WHAT IS COVERED
• The parts are warranted for a 1 year period from the date of purchase.
• Alpine Industries will provide port replacement for original defects, when in accordance to
the owner’s manual and installation guide.
WHAT IS NOT COVERED
• Any damage to the product caused by accident, negligence, misuse, vandalism, external
sources like weather, transit, flood, or electrical outage/power surge.
• Use of parts not installed or assembled in accordance to the
instructions of Alpine.
• Use of components which are not Alpine parts.
• If installed outdoors or in a corrosive or wet environment containing hazardous chemicals.
• Damages caused by cleaning not in line with this manuals instruction.
• Any loss of business, revenue or personal injury as a result of the
product failure, accident, abuse, or misuse.
WARRANTY LIMITATIONS AND EXCLUSIONS
This limited warranty gives you specific rights, and you may also have other rights which vary
from state-to-state. Any other warranties relating to your Alpine product, including, but not
limited to, warranty of merchantability, are limited to the duration of the warranty. Alpine will
not be liable for consequential, incidental, or special damaged you may incur in connection
to your Alpine product. Some states do not allow the exclusion or limitations on incidental or
consequential damaged so this limitation or exclusion may not apply to you.
TO REQUEST WARRANTY SERVICE
Contact the Alpine Industries oce. Proof of purchase is required. The 1 year
warranty begins from the date of purchase. For more information please contact
Alpine at: [email protected] or by phone at: 973-601-5105.

12
NOTES

13
Product #ALP411-V
27 Selvage Street • Irvington, NJ • 07111 • ©2020 All Rights Reserved.
alpineindustries.com