Alpine TME-M710 User manual

SERVICE MANUAL
6.5-INCH WIDE LCD MONITOR
4 / 05-A
68E38530S01
TME-M710
* The model is component system unit of Monitor Unit and AV Interface Unit.
Caution : The part marked with ! is generating a high voltage, so care will be necessary when working.
TO ALPINE Home Page

<Cautions for Safe Repair Work>
The following cautions will prevent accidents in the workplace and will ensure safe products.
*The symbols indicate caution is needed to prevent injuries and damage to property.
The symbols and their meanings follow.
*The following symbols indicate two levels of cautions.
When you see this symbol, you have to be very careful.
When you see this symbol, you have to follow the instructions there.
Do not look squarely into the laser light Fuse Caution
coming from the pickup. Always use a designated fuse.
You may loose you sight. Use of an incorrect fuse may result in a fire.
Do not allow wiring to be caught in the Battery Caution
screw/chassis. Use the designated battery.
If wiring is caught in the screw/chassis, it may Confirm the correct polarity and seat of the
cause a short circuit, resulting in a fire. battery.
An incorrect battery or an improperly connected
or seated battery may result in a fire.
High Temperature Caution Designated Parts Caution
Touching the heat sink may cause severe burns. Look up the part list and ensure that only
designated parts are used to prevent problems or
accidents.
Reverse Power Supply Connections o
r
Wiring Caution
Misconnections Caution Ensure that the wiring is correct when rewiring to
Reverse power supply connections or prevent problems with ignition/breakdown.
misconnections may cause ignition problems and
smoke may result.
Soldering Caution Wear Glove
s
Hot solder from solder splash may cause severe Wear gloves to prevent electrical shocks or injury
burns. from the end face of the metal.
If you ignore this symbol and handle the product incorrectly or unsafely,
injury or only material damage may result.
If you ignore this symbol and handle the product incorrectly or unsafely,
serious injury or death may result.
Warning
Caution
Warning
Caution
- 2 -

TME-M710
Contents
Packing Assembly Parts List
4
Packing Method View
4
Specifications
5
System Connections
6 to 9
Adjustment Procedures
10 to 14
Extension Cable
15
< Monitor Unit >
16 to 25
< AV Interface Unit >
26 to 36
NOTE : Due to continuing product improvement, specifications and designs are subject to
change without notice.
- 3 -

TME-M710
Packin
g
Assembl
y
Parts Lis
t
Part No. Description Part No. Description
#1 101 01E38563S01 ASS'Y,POWER WIRE %1 103 68-02278Z74 MANUAL,OWNER'S
$1 101 01E38578S01 ASS'Y,POWER WIRE &1 103 68-04094Z09 O/M,AOCH M710
%1 101 01E38578S01 ASS'Y,POWER WIRE 104 03E38574S01 SCR,M4X14(WP)(BLK)
&1 101 01E38578S01 ASS'Y,POWER WIRE 105 75E26094S01 TAPE,PAD-MAGIC
102 01E38564S01 ASS'Y,I/F CABLE 20P #1 106 01E38562S01 PARKING,PIN WIRE
#1 103 68-02278Z73 MANUAL,OWNER'S $1 107 01E37298S01 ASS'Y,MONI STAND KIT
$1 103 68-02278Z74 MANUAL,OWNER'S
NOTE : #1:For North American Model Only, $1:For European Model Only, %1:For General Foreign Model Only,
NOTE : #1:For North American Model Only,
$1:For European Model Only,
Others:Common.
&1:For Chinese Model Only, Others:Common.
Packing Method View
No. No.
Symbol Symbol
TOP
103
102
101
106
#1
AV Interface Unit
Monitor Unit
107
105
$1
X2
104 X4
TO CONTENTS
- 4 -

Specifications
<MONITOR>
Screen Size ......................................................................................................................................... 6.5-Type Wide
Display System ........................................................... Low Reflection Rear Projection Type TN Liquid Crystal Panel
Drive System ........................................................................................... Active Matrix Drive, Nomally White Display
Number of Picuture Elements ...................................................................... 280,800 pcs. (H : 1,200 x V : 234 Dots)
Light Source ........................................................ Internal Optical System (U-Type Cold Cathode Fluorescent Tube)
<AUDIO>
Channel Balance (1kHz) ............................................................................................... Head Phone Output : 0±3dB
Frequency Response (Ref. 1kHz) ......................................................................... Speaker Output : 100Hz : -2±3dB
10kHz : -6±3dB
Head Phone Output : 100Hz : -2±3dB
10kHz : 0±3dB
S/N Ratio (1kHz) ..................................................................................................................... Speaker Output : 50dB
Head Phone Output : 45dB
Separation (1kHz) ........................................................................................................... Head Phone Output : 40dB
Distortion (1kHz) ..................................................................................................................... Speaker Output : 1.0%
Head Phone Output : 1.0%
Output Level (1kHz, Volume Max.) ............................................................................. Speaker Output : 1,800mVrms
Head Phone Output : 700mVrms
<NAVIGATION>
Frequency Response (Ref. 1kHz) ......................................................................... Speaker Output : 100Hz : -2±3dB
10kHz : -6±3dB
S/N Ratio (1kHz) ..................................................................................................................... Speaker Output : 50dB
Distortion (1kHz) ..................................................................................................................... Speaker Output : 1.0%
Difference Output Level (Ref. AUX-IN 1kHz) ....................................................................... Speaker Output : -3±3dB
<GENERAL>
Power Supply ...................................................................................................................... DC14.4V (11.0 to 16.0V)
Audio Output/Impedance ............................................................................... Speaker Output : 1,200mVrms / 8 ohm
Head Phone Output : 250mVrms / 32 ohm
Dimension (W x H x D) ............................................................................................ Monitor Unit : 161 x 109 x 29mm
AV Interface Unit : 130.6 x 109 x 30mm
Weight .......................................................................................................................................... Monitor Unit : 270g
AV Interface Unit : 400g
NOTE : Due to Continuing product improvement, specifications and designs are subject to change without notice.
TME-M710
TO CONTENTS
- 5 -

1
o
u
a
;
d
f
g
h
s
p
q
we
r
2
y
t
q
8
3
4
5
6
7
9
i
Make connections correctly.
Improper connections may cause a fire or operation failure.
Battery
Chassis
Basic connection
System Connections
TME-M710
(North American Model Only)
TO CONTENTS
- 6 -

FR
ES
DE
SE
IT
1Foot brake lead (Yellow/Black)
Connect this lead to the foot brake lead powered
when the foot brake is pressed.
2Hand brake lead (Yellow/Blue)
Connect this lead to the hand brake lead
powered when the hand brake is pulled.
3Dimmer lead (White/Blue)
This lead may be connected to the vehicle’s
instrument cluster illumination lead. This will
allow the backlighting of the unit to dim whenever
the vehicle’s lights are turned on.
45 Remote control output lead (White/Brown)
To remote control input lead of ALPINE products
used in the system.
6Reverse Lead (Orange/White)
Use only when a back-up camera is connected.
Connect to the plus side of the car’s reverse
lamp that lights when the transmission is shifted
into reverse (R).
Switches the video picture to the back-up
camera. This is linked with putting the car into
reverse (R).
7ACC power lead (Red)
To ACC power lead powered when engine key
position is ACC.
8Fuse (7.5A)
9Ground lead (Black)
Connect the lead to a good chassis ground on
the vehicle. Make sure the connection is made to
bare metal and is securely fastened using the
sheet metal screw provided.
pFoot brake lamp
qBrake connector (Included)
wFoot brake lead
eFoot brake switch
rHand (parking) brake lamp
tHand (parking) brake lead
yHand (parking) brake switch
uHeadphone
iMain monitor
oConnection cable
If the cable is too short, use the extension cable
(KWE-664N, sold separately).
;RGB cable
aTo RGB output terminal
sMade by Alpine navigation
dAudio input connectors (AUX 1)
Use these connectors to input the audio signals
from a DVD player, video deck etc.
fVideo input connector (AUX 1)
Use this connector to input the video signals
from a DVD player, video deck etc.
To prevent external noise from entering the
audio system.
• Locate the unit and route the leads at least
10cm away from the car harness.
• Keep the battery power leads as far away from
other leads as possible.
• Connect the ground lead securely to a bare
metal spot (remove the coating if necessary)
of the car chassis.
• If you add an optional noise suppressor,
connect it as far away from the unit as
possible.Your Alpine dealer carries various
Alpine noise suppressors, contact them for
further information.
• Your Alpine dealer knows best about noise
prevention measures so consult your dealer for
further information.
gAudio input connectors (AUX 2)
Use these connectors to input the audio signals
from a DVD player, video deck etc.
hVideo input connectors (AUX 2)
Use this connector to input the video signals from
a DVD player, video deck etc.
• When connecting a rear view camera, use the “AUX
IN 2”.
TME-M710
TO CONTENTS
- 7 -

Make connections correctly.
Improper connections may cause a fire or operation failure.
Basic connection
u
y
i
7
2q
w
p9
3
4
5
6
1
8
e
t
o
;
a
s
r
(General Foreign Model Only)
TME-M710
TO CONTENTS
- 8 -

1Parking brake lead (Yellow/Blue)
Connect this lead to the parking brake lead
powered when parking brake is pulled.
2Dimmer lead (White/Blue)
This lead may be connected to the vehicle’s
instrument cluster illumination lead. This will
allow the backlighting of the unit to dim whenever
the vehicle’s lights are turned on.
34 Remote control output lead (White/Brown)
To remote control input lead of ALPINE products
used in the system.
5Reverse Lead (Orange/White)
Use only when a back-up camera is connected.
Connect to the plus side of the car’s reverse
lamp that lights when the transmission is shifted
into reverse (R).
Switches the video picture to the back-up
camera. This is linked with putting the car into
reverse (R).
6ACC power lead (Red)
To ACC power lead powered when engine key
position is ACC.
7Fuse (7.5A)
8Ground lead (Black)
Connect the lead to a good chassis ground on
the vehicle. Make sure the connection is made to
bare metal and is securely fastened using the
sheet metal screw provided.
9Parking Brake Lamp
pBrake Connector (Included)
qParking Brake Signal Lead
wParking Brake Switch
eHeadphone
rMain monitor
tConnection cable
If the cable is too short, use the extension cable
(KWE-664N, sold separately).
yRGB cable
uTo RGB output terminal
iMade by Alpine navigation
oAudio input connectors (AUX 1)
Use these connectors to input the audio signals
from a DVD player, video deck etc.
;Video input connector (AUX 1)
Use this connector to input the video signals
from a DVD player, video deck etc.
aAudio input connectors (AUX 2)
Use these connectors to input the audio signals
from a DVD player, video deck etc.
sVideo input connectors (AUX 2)
Use this connector to input the video signals
from a DVD player, video deck etc.
•When connecting a rear view camera, use the “AUX
IN 2”.
To prevent external noise from entering the
audio system.
•Locate the unit and route the leads at least
10 cm away from the car harness.
•Keep the battery power leads as far away from
other leads as possible.
•Connect the ground lead securely to a bare
metal spot (remove the coating if necessary)
of the car chassis.
•If you add an optional noise suppressor,
connect it as far away from the unit as
possible.Your Alpine dealer carries various
Alpine noise suppressors, contact them for
further information.
•Your Alpine dealer knows best about noise
prevention measures so consult your dealer for
further information.
TME-M710
TO CONTENTS
- 9 -

Adjustment Procedures
TME-M710
2. Cancellation of AUX Regulation (Parking Wire)
1. Preparation product :
(1) HAND : L <GND> (ON), FOOT : H <14V> (ON)...by initial setting
(2) HAND : H <14V> (OFF)
(3) HAND : L <GND> (ON)
(4) FOOT : L <GND> (OFF)
(North American Model Only)
(1) Parking Brake : L <GND>
(General Foreign Model Only)
* TME-M770 and NAVIGATION (North American : NVE-N872A, General Foreign : NVE-N099P) are needed for adjustment.
3. VIDEO Adjustment
(1) Connection
+
-
Figure 1
DC Volt Meter
MONITOR Unit
AV Interface Unit
GND
TP540(VSS)
TME-M710
+
-
Figure 2
DC Volt Meter
MONITOR Unit
AV Interface Unit
GND
TP529(VGH)
TME-M710
+
-
Figure 3
MONITOR Unit
AV Interface Unit
GND
TP549(HSYNC)
TME-M710
Frequency Counter
Figure 4
MONITOR Unit
AV Interface Unit
RGB-IN
NAVIGATION
NVE-N099P or NVE-N872A
<Map information is displayed. >
TME-M710
TO CONTENTS
- 10 -

TME-M710
Figure 5
MONITOR UnitMONITOR Unit
AV Interface UnitAV Interface Unit
AUX-IN
COMPOSITE SIGNAL
RGB-IN AUX-OUT
NAVIGATION
NVE-N099P or NVE-N872A
TME-M710
TME-M770
+
-Figure 6
MONITOR Unit
AV Interface Unit
GND
TP525(VCOM)
TME-M710
Pattern Generator
+
-
(10STEP SIGNAL : NTSC)
GND
AUX IN
Oscilloscope
+
-Figure 8
MONITOR Unit
AV Interface Unit
GND
TP530(GREEN)
TME-M710
Pattern Generator
+
-
(10STEP SIGNAL : NTSC)
(10STEP SIGNAL : NTSC)
GND
AUX IN
Oscilloscope
Figure 7
MONITOR Unit
AV Interface Unit
GND
TME-M710
Pattern Generator
+
-
STEP13 : (10STEP SIGNAL : NTSC)
GND
AUX IN
+
-Figure 9
MONITOR Unit
AV Interface Unit
GND
TP528(RED)
TME-M710
Pattern Generator
+
-
STEP14 : (PAL COLOR BAR)
(PAL COLOR BAR)
GND
AUX IN
Oscilloscope
+
-Figure 10
MONITOR Unit
AV Interface Unit
GND
TP532(BLUE)
TME-M710
Pattern Generator
+
-GND
AUX IN
Oscilloscope
<Map information is displayed. >
TO CONTENTS
- 11 -

TME-M710
(2) Adjustment Procedures
Step Operations Process Connection
Test Point/
P.W.Board
Coordinates
Adjustment
1Confirm AUX terminal OPEN.
AUX terminal Figure 1 to 3
Figure 1
Figure 2
2VSS Voltage Adjustment Adjust by VR501 so that it may be set to
-16V+0.05, -0.05.
3
VGH Voltage Adjustment Adjust by VR500 so that it may be set to
+13V+0.05, -0.05.
4HSYNC Frequency Adjustment
NAVI Screen Adjustment (1)
NAVI Screen Adjustment (2)
Switching MODE1 and setting DIAG Mode
Figure 3
Figure 4
Adjust by VR504 so that it may be set to 15.73KHz.
5
(1) After connecting NAVIGATION(*) and TME-M710,
switched NAV. Mode.
(2) Monitored NAVI position adjustment screen by
TME-M710.
<NAVIGATION (*) Screen position setting value :
“X=-2, Y=00”>
(3) Adjust by VR503 so that a white line may be
visible to right and left of NAVI position adjustment
screen.
(1) Switched MODE1 by pushing long DISP Key.
(2) Inputed 10STEP SIGNAL NTSC to AUX-IN 1
(TME-M710).
(3) After pushing long POWER Key, pushed VOLUME
Down Key and VOLUME Up Key in an order.
(Setting DIAG Mode)
(1) Switched NTSC COLOR BAR.
(2) Set up NTSC COLOR value “65” by VOLUME Up/
Down Key.
(3) Adjust by VOLUME Up/Down Key as becoming the
waveform of Figure 14.
(1) After connecting NAVIGATION(*) and TME-M770,
inputed Composite Signal to TME-M710 AUX-IN1.
(2) Monitored NAVI position adjustment screen by
TME-M710.
<NAVIGATION(*) Screen position setting value :
“X=00, Y=00”>
(3) Switched AUX1 Mode (TME-M710).
(4) Switched MODE2 by pushing long DISP Key.
(5) Adjust by VR505 so that a white line may be
visible to right and left of NAVI position adjustment
screen.
8COM AMP Adjustment Figure 6
Figure 6
9COM DC Adjustment Figure 7
BRIGHT Adjustment Figure 8
10
CONT-RGB 2 Adjustment Figure 7
11
NTSC TINT Adjustment Figure 9
12
Adjust to 6.5Vp-p by VOLUME Up/Down Key as
becoming the waveform of Figure 11.
Adjust by L508 so that outside frame of H characters
shown in Figure 13 may become black.
Adjust by VOLUME Up/Down Key so as that flicker of
screen may disappear.
TP540
(4-E)
TP529
(4-E)
TP549
(4-E)
6
7
Figure 5
TP525
(4-E)
TP530
(4-F)
TP528
(4-F)
(1) Switched PAL COLOR BAR.
(2) Adjust by VOLUME Up/Down Key as becoming the
waveform of Figure 15.
Adjust by VOLUME Up/Down Key as becoming the
waveform of Figure 15.
Adjust to black color should be set to “0 level” by
VOLUME Up/Down Key as becoming the waveform
of Figure 12.
PAL COLOR Adjustment Figure 9
13 TP528
(4-F)
PAL TINT Adjustment Figure 9
14 TP528
(4-F)
TO CONTENTS
- 12 -
NOTE : NAVIGATION(*) = North American : NVE-N872A, General Foreign : NVE-N099P

TME-M710
Step Operations Process Connection
Test Point/
P.W.Board
Coordinates
Adjustment
Adjust by VOLUME Up/Down Key as becoming the
waveform of Figure 16.
Cancelled DIAG Mode by Pushing POWER Key at
DIAG Mode.
PAL PHASE Adjustment
Cancellation DIAG Mode
Figure 10
Figure 10
15
16
TP532
(4-F)
Figure 11
Figure 13
Figure 12
TO CONTENTS
- 13 -

TME-M710
Figure 14
Figure 16
Figure 15
TO CONTENTS
- 14 -

TME-M710
Extension Cable
*Always connect the Extension Cable when making checks of voltage and repair.
< Monitor Unit >
LCD Display
32PIN
MONITOR P.W.Board
KEY P.W.Board
CB504
CB500
CB900
(1) (2)
(1) 01E37339S01
(2) 01E37341S01
TO CONTENTS
- 15 -

TME-M710
< Monitor Unit >
Block Diagram
17
Parts Layout on P.W.Boards and Wiring Diagram
18 , 19
Schematic Diagram
20 , 21
Terminal Voltage of IC/TR
22 to 24
Exploded View (Cabinet)
25
NOTE : Due to continuing product improvement, specifications and designs are subject to
change without notice.
TO CONTENTS
- 16 -

TME-M710
Block Diagram
ACC+5V
SHIELD-GND
KEY
P-GND
REMSEN
SP-OUT
DC/DC
CONVERTER
PWR+5V
REG.
POW
IND.
REMO-CON
RECEIVER
DIMMER
ICC:Max1mA
KEY
ACC+5V
GND
KEY
REMSEN
GND
GND
CHROMATIC
CIRCUIT
3.58
MHz
4.43
MHz
TFT
CONTROL
CIRCUIT
LCD
PANEL
UNIT
BACK
LIGHT
INVERTER
MDW, MDN
SLK
DI
Vcc1
P.SAVE
OSD RESET
SYNCOUT
RGB
RGB/VIDEO
BLKIN TC
Vcc2
Vcc3
13V ICC2: 6
BL-PWM(BL-OFF)
RGB
+5V
HSY
VSY
NTSC/PAL
VCS
SYNI
VSH
+5V +13V
VGH VGL
-10V
VCC
-11V
S-GND
VSS
-16V
ACC+9V ACC+9V
ACC+9V
ACC+5V
REG.
VSH,V5B
-16V
POW-CTL
VGL-CTL
VGH-CTL
V-MUTE
+13V -11V
-10V
-11V
-10V
VDD
BL-GND
1
2
3
4
5
6
7
9
10
11
16
17
18
19
20
13
14
15
ACC+5V
NTSC/PAL
P.GND
DIMMER
ACC+3.3V
REG.
ACC+3.3V
DAC
MODE1, 2 ICC1:58mA
mA
ICC3:1.5mA
IL=6mArms(Max6.5)
VL7:660Vrms(Max730)
WL:4.29W
ISH:60mA
IGH:1mA
IGL:-1mA
ICC:1mA
ISS:-1mA
IDD:15mA
Hsync
BL +9V
12
CS_OSD
8CS_DAC
CS_DECODER BUFFER
BUFFER
OSD
BUFFER
BUFFER
BUFFER
RGB
7SH
32FU
VSH,V5B
TC7S
66FU
BUFFER
TO CONTENTS
- 17 -

CB900 TP905
TP904
TP903
TP902
TP901
E900
IC900
R909
R908
R907
R906
R905
R904
R903
R902
R901
SW904SW903 SW902
SW901 SW900
Q901
ZD900LD900
C598 C597
C596
C595 C594
C593
IC513
IC512
C592
C591
IC510
IC509
C589
IC508
C588
IC507
IC506
IC505
T500
IC504
IC503
IC502
C582
IC501
C580
C578
C577
C576 C575
D515
C574
C573
D507
C566
C565
D504
D503
D502
C561
D501
D500
SD502
SD501
SD500
R590
C550
R589 R588
R587
R586
C549
R585
C548
C547
R583
C546
R582
C545
R581 R580
C544
C543
C540
R578
R577 R576
C539
R575
C538
R574
C537
R573
C536
C535
R571
C534
C533
C532
C530
R566
C529
VR505
VR504
R564 VR503
VR502
C526
VR501
C525
VR500
C524
C523
XL501
C520
XL500
R556
C519
C518
R553
R552
R550
C511
R547
R546
R545
C509
R544
R543
R542
R541
R540
C500
R538 R536
R535
R533
R532
R529
R528
R527
R526R525R524
R523 R522
R519
R516 R515 R512
R511
R508
R500
L514
L513
L512
L511
L510 L509
L508
L506
Q512
Q509
Q508
Q501 Q500
TP548TP547TP546
ZD503
ZD502 ZD501
ZD500
TP534
CB504
CB503
CB502
CB501
CB500
F500
C615
RA505
C608
RA503
RA502
RA501
C603
C600
R634
R633
R618
R617
R616R613
R612
E513
E512
E511
E510
R608
R607
R606
R605
E509
E508
R602
E506 E505
E504
E502
E501
Orange Color Pattern:Component Side Pattern
Blue Color Pattern:Foil Side Pattern
MONITOR P.W.Board
(Component Side View)
KEY P.W.Board
(Foil Side View)
TME-M710
Parts Layout on P.W.Boards and Wiring Diagram(1/2)
KEY P.W.Board
(Component Side View)
To CB900
17
2 34
1
SPEAKER, 8ohm-1W
SP502
(Bottom Side View)
ASSY,LB065WQ2
LCD504
B
WHT
PNK
1 2
132
A
To CB503
2 1
1
2
BLK
RED
12
To CB502
21
(B.BOX P.W.Board (CB101))
To AV Interface Unit
17
To CB500
To CB504
32 1
4 51
3
54
31
BE EB
EB
EBEB
Caution:The part marked with is generating a high voltage,
so care will be necessary when working.
1
2
3
4
5
AFGEDCB
TO CONTENTS
- 18 -

C599
IC511
C590
C587
C586
C585
C584
C583
C581 C579
C572 C571
C570 C569
C568 C567
C564
C563
C562
C560 C559
C558 C557 C556
C555
C554
C553
C552
C551
C542
C541
R570
C531
R569
R568
R567
R565
C528
C527
R561
R560
C522 C521
R559
R558
R557
C517
C516
C515
C514
C513
C512
R549
R548
C506
C505
C504
C503
C502
C501
R539 R537 R534
R520
R518
R517
R514
R513
R510
R509
R507
R506
R505
R504
R503
R502
R501
L516
L515
L505
Q511
Q510
TP552
TP551
TP550
Q507
Q506
Q505
Q504
Q503
Q502
TP549
TP545
TP544
TP543
TP542
TP541
TP540
TP539
TP538
TP537
TP536
TP535
TP533
TP532
TP531
TP530
TP529 TP528
TP527
TP526
TP525
TP524
TP523
TP522
TP521
TP520
TP519
TP518
TP517
TP516
TP515
TP514
TP513
TP512
TP511
TP510
TP509
TP508
TP507
TP506TP505
TP504
C614
TP503
C613
TP502
C612
C611
TP501
C610
RA506
C609
RA504
C607
C606
C605
RA500
C604
C602
C601
R635
R632
R631
R630
R627
R626
R625
R624
R623
R622
R621 R620
R619
R615
R614
R611
R610
E514
R609
R604
R603
VD500
Orange Color Pattern:Component Side Pattern
Blue Color Pattern:Foil Side Pattern
MONITOR P.W.Board (Foil Side View)
TME-M710
Parts Layout on P.W.Boards and Wiring Diagram(2/2)
TP528
TP530
TP532
TP525 TP540TP549
TP529
EB
E B
BE
23 15
5
32
1
B
E
15
43
EB
32
1
5
1
2
3
4
5
AFGEDCB
TO CONTENTS
- 19 -

CB500
CONN,FFC-7P
TP509 TP510
TP511
TP518
C502 10 C504 10
C512 10
C517 10 C521 10 C505 10 C522 0.1C523 0.1
C531 N.U.C532 N.U.
C528 0.1C529 0.1
C535 0.1
C513 10
C506 0.1
C514 0.1
C515 0.01
C516 0.022
C509 0.01
C500 0.01
IC512
BA05SFP
IC501
NJM2880U33
C511
0.01
L505
2.2u
L506
2.2u
E501
100/6.3
C538 390p
R526 10k
C543 2.2
R527 2.7k
R528 10k
R529 68k
C545
0.01
R541
10k
R546
68k
C547
0.1
R542
68k
VR501
22k
IC502
BA05SFP
C534 0.1
R524 68k
C536 0.22
R525
220k
R540
1k
VR500
2.2k R532
2.2k
R535
33k
R543
27k
R545
12k
C544
0.01
IC507
AN8018SA
SD502
SB05-05CP
L510
330u
Q501
2SC4540
R558
1
Q504
XN1A311
E506 330/25
R631 1.2k-1/4
C554 0.01
C563 0.1
R565
4.7k-F
R569 10k-F
C567 1 C568 1
R567
18k-F
C569
10
C570
10
R568
12k-F
R570
30k-F
VR502
N.U.
C571
10
C572
10
R544
1k
R547
560-1/4
L509 470u
E505 330/25
C552 0.01
R630 16k
R560
22k
R559
22k
C562 220p
C564 1
Q502
2SD1782K
R513
5.6k-F
R582
100
C578
470p
R586
47k
RA502 100
C579 10
C581 10
C583 0.1
R583 100
R580 10k
R581 N.U.
R585 N.U.
R587 10k
RA501
560
R590
22k
IC510
TC7SH32FU
C577
0.1
C584 1000p C585 1000p
C587 33p
C588 0.1
RA500
100
R602
100
R614
68k
R611
5.6k
R604
0.1
R615 1M
C601 560p
R612
24k
R607
47k
R610
68k
IC511
NJM2107F
C599 1
C602 0.022
D507
MA2S111
R609
3.6k
C594 10
C595 220p
C593 0.1
C592 0.1
R608
390
L512
15u
C603
1000p
C596
33p
C600
33p
R617
560k
R618
560k
SD500
MA716
R622
18k
C609
1000p
C610
100p
L514
2.7u
R625
3.3k
Q510
2SC2411K
TP529 TP531 TP533
R627 330
C611 330p
CB504
CONN,FFC-32P
LCD504
ASSY, LB065WQ2
C605 0.1
R620
5.6k
ZD500
MAZS0510M
VR504
2.2k
C606 0.1
VD500
MA335-TX
R619
8.2k
R624
2.7k
R626
100
R606
1M
IC509
LZ9GH29
RA506
100
IC513
TC7S66FU
C586
82p
VR503
100k
VR505
100k
R605 220k
C591 0.22
Q500
2SA1735
SD501
SB05-05CP
R556
560
R557
1
C549 0.1
E504 100/16
Q503
XN1A312
TP549 TP550 TP534
R514
4.7k-F
TP535
TP536
TP537
TP538
TP539
TP541
TP540
TP524 TP525 TP526 TP527
R623 13k
C607 0.022
C608 N.U.
C614 100p
TP528 TP530 TP532 TP542 TP543 TP544 TP545
T500
BLC4115
TP551 TP552
CB503
CONN,WTB-2P
Q509
2SD1760
Q508
2SD1760
R616
820-1/4
R613
820-1/4
L513 68u
C597 0.18
C598
N.U.
Q506
DTC124EKA
Q505
DTC124EKA
Q507
FMY1A
R604
2.7k
R603
10k
F500
1.6A
C589 N.U.
E511 100/16
E512 100/16
L511
100u
C590
0.1
CB501
CONN, CSS5020-20P
TP513
TP514
TP515
TP516
TP521TP506
TP507
TP508
TP522
TP523
TP512
TP519
TP520
D500 1SS355
D501 1SS355
D502 1SS355
D503 1SS355
D504 1SS355
RA504
47k
D515
1SS355
R500
1k
R509 10k
R510 10k
C527 0.1
R506
10k
R507 10k
R508 10k
ZD501
MAZS056M
ZD502
MAZS056M
ZD503
MAZS056M
IC503
TC74VHC14FT
C541 0.1
IC505
TC74VHC14FT
IC506
NJU3713AV
R512
1k
C524 1000p
C525 1000p C526 1000p C530 1000p
C533
1000p
RA503
560 E502 100/16
C537 0.1
C501 10
R519
1k
R516
560
R515
560
C519 1000p
C520 1000p
C518 0.1
TP501
TP502
TP503
TP504
TP505
SP502
SPEAKER, 8ohm-1W CB502
CONN,WTB-02P
R534 1.2k R537 1.2k R539 1.2k
R533 3.9k R536 3.9k R538 3.9k
C540
27p
L508
FSDV
TP517
C539
27p
C542 0.1
C503 10
R522
10k
IC504
MB90097PFV
R511
2.2k
R523
N.U.
C546
N.U.
C612 N.U.
C548 1
R550 270
E513 47/16
R552 18k-F
C550 0.1
R553 10k
R548 1k
R549 N.U.
L515
2.2
R633
0
R505 47k
Q512
DTA124EKA
RA505
100
R634
N.U.
C553 0.01 C555 0.01 C556 0.01 C557 0.01 C558 0.01
C559 1
C613 10
0.01
C551
R635 560
R561
N.U.
R503
560
C560
82p
R504
1k R518 2.7k
C565 1
R566 1M
C566 6800p
C574 0.1
R578
1M
Q511
2SC2412K
R501
47k
R520
47k
R502
39 1/4
R517
36 1/4
E514
10
C573 0.1
R573 75
R574 75
R575 75
TP546 TP547 TP548
L516
2.2u
E510
47/16
R564 10k
E509 100/16
E508 10/16
C561 0.1
R632
10k
IC508
RB5P0090M
R576 1k
R577 1k
R571 1.8k
C575 3p
XL500
4.43MHz
C576
3p
C582
0.47
R588
5.6k
R589
8.2k
C580
0.01
XL501
3.57MHz
C615
0.01
R621
68
TO CONTENTS
TO PARTS LIST
TO P. W. BOARD
- 20 -