Assembling & Using Your Product
Unpack all components carefully. Please check to ensure all parts have been
removed from the packaging.
Components:
Assembly:
1. Place the Wheelbarrow Frame (A) on a smooth, level surface.
2. Place the Wheelbarrow Body (B) on top of the Wheelbarrow Frame (A)
with the three bolts running through the three holes in the crossbars of the
frame. (See !)
3. Place Cap Nuts (C) on the three bolts and tighten them with a small
wrench. (See ")
4. Slide the Fountain Post (D) onto the post on the Wheelbarrow Body (B)
and position it with the tip of the shovel over the center of the Wheelbarrow
Body (B). Tighten the built-in wing bolt to secure it. (See #)
5. Remove the Submersible Pump (E) from its packaging and adjust the flow
control to its lowest setting.
6. Place the Pump (E) suction feet down back inside the Wheelbarrow Body
(B) and pull the cord through cutout in the top. (See $)
7. Connect vinyl tubing attached to the top of Pump (E) to the bottom end of
the Fountain Post (D).
8. Place the Metal Mesh (F) under the tip of the shovel. (See %)
9. Without splashing, gently pour water into the Wheelbarrow Body (B) of the
fountain. Using distilled water prevents scale build-up. Do not allow water
to overflow! Make sure the water completely covers the Pump (E).
10. Congratulations, your fountain is now complete. Plug the power cord for
the pump into your local power supply and enjoy!
IMPORTANT: Make sure no water is near the plug and always keep the power
source in a dry place.
The first time you operate the pump it can take up to 5 minutes for the air to be
completely expelled and water begins to flow properly. Don’t forget to add
water regularly as water will evaporate over time.
Trouble Shooting & Cautions
If you have any questions and/or problems, please contact the retail store where you
purchased this fountain.
•If your pump fails to run
•
Check the circuit breaker or try a different outlet to make sure the pump is
receiving electrical power.
•
Check the pump discharge and tubing for any kinks and/or obstructions.
•
Any buildup obstructing the water flow can be flushed with a garden hose.
•
Check the rotor by removing the front cover & plate to access the impellor area.
Turn the rotor and make sure that the rotor is not jammed or broken.
•If your pump “spews”
•
Check the water level to make sure the pump is completely submerged and there
if enough water in the basin to operate your fountain. Not having enough water
will cause your pump to spew.
•If your pump is making abnormal loud noises
1. Disconnect the pump from the electrical power supply and remove the front
cover.
2. Carefully grip the impeller and gently pull the impeller/rotor assembly out of the
pump housing.
3. Rinse the impeller/rotor assembly and clean the cavity with clean water. If
breakage or damage is found, contact your local retailer for parts.
•Fountain Care
•
We recommend using all-natural cleansing formula to eliminate foam, lime scale,
and calcium buildup; fight mineral deposits; leave water crystal clear; help
prevent staining; remove organic contaminants; and treat discolored water. This
formula will help prevent pump damage due to hard water build up.
•Caution
•
Always unplug the pump from the solar panel before cleaning & handling.
•
Uses with clean water only, do not place the fountain and/or parts in any
other liquid.
•
Periodically change water & clean the pump to keep free from micro-
organisms.
•
Disconnect and store the unit in a dry place if not in use for extended
periods of time.
•
Do not lift, carry, or pull the pump by the power cord.
•
NEVER LET THE PUMP RUN DRY.
Wheelbarrow Body
Cap Nut
Fountain Post
Metal Mesh
Submersible Pump
