Alpine iLX-507E User manual

ALPINE iLX-F509E 68-41657Z84-A (EN)
7-INCH AUDIO/VIDEO RECEIVER
iLX-507E
HALO9 9-INCH AUDIO/VIDEO RECEIVER
iLX-F509E
HALO11 11-INCH AUDIO/VIDEO RECEIVER
iLX-F511E
•OWNER’S MANUAL
Please read before using this equipment.
1500 Atlantic Blvd,
Auburn Hills, Michigan 48326, U.S.A.
Phone 1-800-ALPINE-1 (1-800-257-4631)
161-165 Princes Highway,
Hallam Victoria 3803, Australia
Phone [phone]
Ohmstrasse 4, 85716 Unterschleissheim, Germany
Phone: [phone]
For contact information on your respective country,
please visit www.alpine-europe.com.
Aurora House, Deltic Avenue
Rooksley, Milton Keynes, MK13 8LW
United Kingdom
Phone: [phone]
The 9th Towers, Tower B, 24th Floor, Unit TNB01-03,
33/4 Rama 9 road, Huay Kwang, Bangkok, 10310, Thailand
Phone [phone]
Designed by ALPS ALPINE Japan
Printed in Thailand
68-41657Z84-A (Y_A5)
YAMAGATA THAILAND HQ
324 Moo 4, Bangpoo Industrial Estate Soi 6B, Sukhumvit Road,
T.Praksa, A.Muang Samutprakarn, Samutprakarn 10280

ALPINE iLX-F509E 68-41657Z84-A (EN)

ALPINE iLX-F509E 68-41657Z84-A (EN)
3-EN
English
CONTENTS
Operating Instructions
WARNING
Points to Observe for Safe Usage ...............................7
WARNING ...........................................................7
CAUTION.............................................................8
NOTICE................................................................8
Getting Started
Location of Controls.....................................................10
Turning Power On or Off.............................................11
Adjusting the Volume..................................................11
Lowering Volume Quickly ..........................................11
Turning off the Screen/Button Illumination
(Display OFF) ...............................................................11
Touch Screen Operation.............................................11
Switching Sources.........................................................12
Selecting an Item in a List ..........................................12
About the HOME Screen.............................................12
About the Indicator Display ......................................13
Setup
Setup Operation............................................................13
Device Setup
Displaying Device List..................................................14
Pairing the Bluetooth® Device..................................14
Connecting the Device Registered in the
Device List ....................................................................15
Disconnecting the Connected Device...................15
Deleting a Bluetooth Device from the list............15
Wi-Fi Setup.......................................................................15
Setting the Wi-Fi .......................................................15
Bluetooth Setup.............................................................15
Setting the Bluetooth.............................................15
Setting the Auto Connection...............................15
Setting the PIN Code...............................................15
Displaying Device Information.................................16
Function Setup
Apple CarPlay Setup.....................................................16
Adjusting the Media Level....................................16
Adjusting the Phone Calls Volume ....................17
Adjusting the Ringtones and Alerts Level.......17
Adjusting the Notifications and Guidance
Level ..........................................................................17
Adjusting the Voice Recognition Level ............17
Adjusting the Microphone Level........................17
Android Auto Setup .....................................................17
Adjusting the Media Level....................................17
Adjusting the Phone Calls Volume ....................17
Adjusting the Ringtones and Alerts Level.......17
Adjusting the Notifications and Guidance
Level ..........................................................................17
Adjusting the Voice Recognition Level ............18
Adjusting the Microphone Level........................18
Radio Setup.....................................................................18
Adjusting the Radio Volume ................................18
USB Setup ........................................................................18
Adjusting the USB Volume....................................18
Video Setup................................................................18
iPod Setup........................................................................19
Adjusting the iPod Volume...................................19
AUX (Auxiliary) Setup...................................................19
Adjusting the AUX Volume...................................19
Setting the Auxiliary (AUX) Name......................19
Video Setup................................................................19
HDMI Setup.....................................................................20
Adjusting the HDMI Volume ................................20
Setting the HDMI Name.........................................20
Video Setup................................................................20
Setting the HDMI Selector ....................................20
Phone Setup....................................................................20
Adjusting the Ringtone Level ..............................20
Adjusting the Phone Calls Volume ....................20
Adjusting the Microphone Level........................21
Setting the Phonebook Transfer.........................21
Setting the Phonebook Name Order................21
Setting the Phonebook Calendar.......................21
Bluetooth Audio Setup ...............................................21
Adjusting the Bluetooth Audio Volume...........21
Camera Setup.................................................................21

ALPINE iLX-F509E 68-41657Z84-A (EN)ALPINE iLX-F509E 68-41657Z84-A (EN)
4-EN
Setting the Reverse Camera
(Camera 1) ...............................................................21
Reverse Camera Signal Input Setting ...............22
Camera 2 Setup ........................................................22
Camera 2 Signal Input Setting.............................22
Camera Guide Setup...............................................22
Video Setup................................................................23
Setting the Mute while Reversing......................23
System Setup
Adjusting the Key Sound............................................23
Setting the Microphone Effect.................................24
Language Setup ............................................................24
Adjusting the Clock......................................................24
Setting the Time Format........................................24
Setting the Time Zone............................................24
Setting the Home Screen Type.................................24
Screen/Lighting Setup ................................................24
Setting the Brightness of the Backlighting
(Dimmer)..................................................................24
Adjusting the Dimmer of Button Lighting at
Night..........................................................................25
Adjusting the Minimum Level of Backlight....25
Switching the Display Colour....................................25
Editing HOME screen...................................................25
Setting Car Type.............................................................25
Setting Security Code..................................................25
Setting the password..............................................25
Clearing the password ...........................................26
Vehicle Type Setup........................................................26
Steering wheel Setting...........................................26
Fuel Type Setting......................................................26
EV Connector Type Setting...................................26
Installation Setup ..........................................................26
About iLX-507E/iLX-F509E/iLX-F511E....................26
Displaying the Product Information..................26
Updating Firmware Version..................................26
Dedicated Tuning According to Your Car
(Car by Car Update)..............................................27
Displaying Software License................................27
Initializing the Sound Settings............................27
Initializing the System............................................27
Sound Setup
Setting the Media Xpander (MX).............................28
Equalizer Settings..........................................................28
Adjusting the Parametric Equalizer Curve
(Advanced EQ/Basic EQ).....................................28
Equalizer Presets (Preset EQ)................................29
Fader/Balance/Rear Speaker/Subwoofer
Settings..........................................................................29
Setting the Fader/Balance ....................................29
Rear Speaker Setting...............................................29
Turning Subwoofer ON/OFF ................................29
Time Correction Settings............................................30
Crossover Settings (X-OVER) .....................................30
Setting the "bass engine"...........................................31
Adjusting Bass Level/Treble Level...........................31
Setting the Subwoofer................................................31
Adjusting the Subwoofer Level...........................31
Setting the Subwoofer Phase..............................31
Defeat Setting.................................................................31
About the Crossover ....................................................32
About Time Correction................................................32
Apple CarPlay (Optional)
Access to Apple CarPlay..............................................34
Using Voice Recognition function...........................34
Android Auto (Optional)
What is Android Auto ..................................................35
Activate Android Auto.................................................35
Using Voice Recognition function...........................35
Radio
Radio Basic Operation
Listening to the Radio .................................................36
Presetting Stations Manually....................................36
Presetting Stations Automatically...........................37
Tuning to Preset Station .............................................37
USB Flash drive (Optional)
USB Audio
Playback............................................................................38
Repeat Play......................................................................38
Shuffle Play......................................................................38
Searching for a Desired Song....................................38
USB Video
Playback............................................................................40
Fast-forwarding/Fast-reversing................................40
Repeat Play......................................................................40
Shuffle Play......................................................................40
Searching for a Desired file........................................40
Switching Display Modes...........................................41
udio Tracks .......................................41
de on iPhone (Optional)
............................................................................42
or a Music File...........................................42
lay......................................................................43
lay......................................................................43
vice (Optional)
ation.............................................................44
nput .........................................44
y Modes...........................................45
peration
efore Using.......................................................45
ooth.......................................................45
ee Phone...............................45
e Using Bluetooth..........................................46
ee Phone Control
ing a Call............................................................46
Telephone........................................47
................................................................................47
ing a phone call using the Phone
.........................................................................47
ation Screen ............................................47
Volume.............................47
ing the Voice Output..................................48
icrophone ........................................48
Touch-Tone) Function ..............................48
ook Function ..................................................48
ching in the Phone Book ..............................48
onizing the Phone Book...........................48
hone Book Entries .......................48
udio
............................................................................49
lay......................................................................49
lay......................................................................50
or a Desired file........................................50
ting a Bluetooth Device...............................50
onnecting the Bluetooth Connection......50
ching the connecting Bluetooth
e.......................................................................50
y Device (Optional)
uxiliary Devices (Optional) ................51
y Modes...........................................51

ALPINE iLX-F509E 68-41657Z84-A (EN)ALPINE iLX-F509E 68-41657Z84-A (EN)
5-EN
Fader/Balance/Rear Speaker/Subwoofer
Settings.......................................
Setting the Fader/Balance
Rear Speaker Setting
Turning Subwoofer ON/OFF
Time Correction Settings
Crossover Settings (X-OVER)
Setting the "bass engine"
Adjusting Bass Level/Treble Level
Setting the Subwoofer
Adjusting the Subwoofer Level
Setting the Subwoofer Phase
Defeat Setting
About the Crossover
About Time Correction
Apple CarPlay (Optional)
Access to Apple CarPlay
Using Voice Recognition function
Android Auto (Optional)
What is Android Auto
Activate Android Auto
Using Voice Recognition function
Radio
Radio Basic Operation
Listening to the Radio
Presetting Stations Manually
Presetting Stations Automatically
Tuning to Preset Station
USB Flash drive (Optional)
USB Audio
Playback
Repeat Play
Shuffle Play
Searching for a Desired Song
USB Video
Playback
Fast-forwarding/Fast-reversing
Repeat Play
Shuffle Play
Searching for a Desired file
Switching Display Modes
Switching the Audio Tracks .......................................41
iPod mode on iPhone (Optional)
Playback............................................................................42
Searching for a Music File...........................................42
Repeat Play......................................................................43
Shuffle Play......................................................................43
HDMI Device (Optional)
HDMI Operation.............................................................44
Switching the HDMI Input .........................................44
Switching Display Modes...........................................45
Bluetooth Operation
Setup Before Using.......................................................45
About Bluetooth.......................................................45
About the Hands-free Phone...............................45
Before Using Bluetooth..........................................46
Hands-free Phone Control
Answering a Call............................................................46
Hanging up the Telephone........................................47
Calling................................................................................47
Making a phone call using the Phone
Menu .........................................................................47
Phone Operation Screen ............................................47
Adjusting the Speech Volume.............................47
Changing the Voice Output..................................48
Muting the Microphone ........................................48
DTMF (Touch-Tone) Function ..............................48
Phone Book Function ..................................................48
Searching in the Phone Book ..............................48
Synchronizing the Phone Book...........................48
Deleting the Phone Book Entries .......................48
Bluetooth Audio
Playback............................................................................49
Repeat Play......................................................................49
Shuffle Play......................................................................50
Searching for a Desired file........................................50
Connecting a Bluetooth Device...............................50
Disconnecting the Bluetooth Connection......50
Switching the connecting Bluetooth
Device .......................................................................50
Auxiliary Device (Optional)
Operating Auxiliary Devices (Optional) ................51
Switching Display Modes...........................................51
Camera Operation (Optional)
Rear Camera Operation...............................................52
Displaying the rear view video while the
car is in reverse ......................................................52
Displaying the Camera Image from the
HOME screen..........................................................52
Guide Display ON/OFF Setting.................................52
Adjusting the Caution Display Location ...............53
Hitch Guide Display ON/OFF Setting.....................53
About the Rear Camera Guide..................................53
Switching the Image Pattern for the Rear
Camera .....................................................................55
Front Camera Operation.............................................55
Displaying the Camera Image from the
HOME screen..........................................................55
Switching the Image Pattern for the Front
Camera .....................................................................55
Side Camera Operation...............................................56
Information
Product Software Update...........................................56
About the Supported Formats ................................56
About MP3/WMA/AAC/FLAC/WAV/APE ..........56
In Case of Difficulty.......................................................58
If this Message Appears..............................................59
Specifications..................................................................60
Installation and
Connections
WARNING ........................................................ 62
CAUTION.......................................................... 62
Precautions ..................................................... 63
Accessory List ................................................................63
Installation.......................................................................63
Caution concerning the installation
location.....................................................................64
Mounting the Microphone...................................64
Mounting the GPS Antenna inside the
vehicle.......................................................................64
Note on using HDMI Connection Cables.........64
Adjusting the display position
(iLX-F509E/iLX-F511E).........................................66
Installation example using the Original
Mounting Bracket.................................................66
Adjust the up-down position of the Display
unit (iLX-F509E/iLX-F511E)................................67

ALPINE iLX-F509E 68-41657Z84-A (EN)
6-EN
Install the display unit
(iLX-F509E/iLX-F511E).........................................68
Connections....................................................................69
Connection 1 .............................................................69
Connection 2 .............................................................70
If an ACC power supply is not available...........72
System Example.............................................................73

ALPINE iLX-F509E 68-41657Z84-A (EN)
7-EN
Operating Instructions
WARNING
Points to Observe for Safe Usage
• Read this manual carefully before using this system
components. They contain instructions on how to use this
product in a safe and effective manner. Alpine cannot be
responsible for problems resulting from failure to observe
the instructions in this manual.
• This manual uses various pictorial displays to show you
how to use this product safely and to alert you to
potential dangers resulting from improper connections
and operation. Following are the meanings of these
pictorial displays. It is important to fully understand the
meanings of these pictorial displays in order to use this
manual and the system properly.
• This product may be used with software applications.
Please follow all usage instructions and warnings when
using this product at all times. Do not use this product or
any software application in a manner which will hinder
safe operation of your vehicle.
WARNING
• Operation of the system while driving is dangerous.
Users should stop vehicle before operating the
software.
• Road conditions and regulations take precedence
over information contained on the map display:
observe actual traffic restrictions and circumstances
while driving.
• This software is designed for use exclusively in the
unit. It cannot and may not be used in conjunction
with other hardware.
WARNING
This symbol means important instructions.
Failure to heed them can result in serious injury
or death.
INSTALL THE PRODUCT CORRECTLY SO THAT THE
DRIVER CANNOT WATCH TV/VIDEO UNLESS THE
VEHICLE IS STOPPED AND THE PARKING BRAKE IS
APPLIED.
It is dangerous for the driver to watch TV/Video while
driving a vehicle. Installing this product incorrectly enables
the driver to watch TV/Video while driving. This may cause a
distraction, preventing the driver from looking ahead, thus
causing an accident. The driver or other people could be
severely injured.
DO NOT WATCH VIDEO WHILE DRIVING.
Watching the video may distract the driver from looking
ahead of the vehicle and cause an accident.
DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR
ATTENTION AWAY FROM SAFELY DRIVING YOUR
VEHICLE.
Any function that requires your prolonged attention should
only be performed after coming to a complete stop. Always
stop the vehicle in a safe location before performing these
functions. Failure to do so may result in an accident.
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL
HEAR OUTSIDE NOISES WHILE DRIVING.
Excessive volume levels that obscure sounds such as
emergency vehicle sirens or road warning signals (train
crossings, etc.) can be dangerous and may result in an
accident. LISTENING AT LOUD VOLUME LEVELS IN A CAR
MAY ALSO CAUSE HEARING DAMAGE.
MINIMIZE DISPLAY VIEWING WHILE DRIVING.
Viewing the display may distract the driver from looking
ahead of the vehicle and cause an accident.
DO NOT DISASSEMBLE OR ALTER.
Doing so may result in an accident, fire or electric shock.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
(Check with your dealer if you are not sure.) Failure to do so
may result in fire, etc.
KEEP SMALL OBJECTS SUCH AS SCREWS OUT OF THE
REACH OF CHILDREN.
Swallowing them may result in serious injury. If swallowed,
consult a physician immediately.
USE THE CORRECT AMPERE RATING WHEN REPLACING
FUSES.
Failure to do so may result in fire or electric shock.
DO NOT BLOCK VENTS OR RADIATOR PANELS.
Doing so may cause heat to build up inside and may result
in fire.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.
Use for other than its designed application may result in
fire, electric shock or other injury.
MAKE THE CORRECT CONNECTIONS.
Failure to make the proper connections may result in fire or
product damage.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE
NEGATIVE BATTERY TERMINAL.
Failure to do so may result in electric shock or injury due to
electrical shorts.

ALPINE iLX-F509E 68-41657Z84-A (EN)ALPINE iLX-F509E 68-41657Z84-A (EN)
8-EN
UTION
cepts no responsibility for lost data,
ta, etc., is lost while using this
.
lash drive
ontrol a memory storage device that
ass Storage Class (MSC) protocol.
ormats are MP3, WMA, AAC, FLAC,
.
ive function is not guaranteed. Use a USB
e according to the terms of agreement. Read the
ive Owner’s Manual thoroughly.
orage in the following locations:
e in the car exposed to direct sunlight or high
es.
e the possibility of high humidity or corrosive
es are present.
ive in a location where driver
ed.
ive may not function correctly at high or low
e.
ertified USB flash drive. Note that even certified
ive, may not function correctly depending on
te.
ive type,
te or encoding software, the unit may not
y properly.
ive may take time to start playback. If there is
ive, it
onsiderable time before the file is played back
.
y back“mp3,”“wma,”“m4a,”“flac,””fla,”
“ape” file extensions.
ve extensions to a file other than
ta. This non-audio data will not be recognized.
yback may contain noise that can
.
o back up important data on a
omputer.
ve the USB device while playback is in
. Change SOURCE to something other than USB,
ve the USB device to prevent possible damage
y.
DO NOT ALLOW CABLES TO BECOME ENTANGLED IN
SURROUNDING OBJECTS.
Arrange wiring and cables in compliance with the manual
to prevent obstructions when driving. Cables or wiring that
obstruct or hang up on places such as the steering wheel,
gear lever, brake pedals, etc. can be extremely hazardous.
DO NOT SPLICE INTO ELECTRICAL CABLES.
Never cut away cable insulation to supply power to other
equipment. Doing so will exceed the current carrying
capacity of the wire and result in fire or electric shock.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING
HOLES.
When drilling holes in the chassis for installation, take
precautions so as not to contact, damage or obstruct pipes,
fuel lines, tanks or electrical wiring. Failure to take such
precautions may result in fire.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR
STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.
Bolts or nuts used for the brake or steering systems (or any
other safety-related system), or tanks should NEVER be used
for installations or ground connections. Using such parts
could disable control of the vehicle and cause fire etc.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER
VEHICLE OPERATION, SUCH AS THE STEERING WHEEL
OR SHIFT LEVER.
Doing so may obstruct forward vision or hamper movement
etc. and results in serious accident.
CAUTION
This symbol means important instructions.
Failure to heed them can result in injury or
material property damage.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS.
Failure to do so may cause personal injury or damage to the
product. Return it to your authorized Alpine dealer or the
nearest Alpine Service Center for repairing.
HAVE THE WIRING AND INSTALLATION DONE BY
EXPERTS.
The wiring and installation of this unit requires special
technical skill and experience. To ensure safety, always
contact the dealer where you purchased this product to
have the work done.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM
SECURELY.
Be sure to use only the specified accessory parts. Use of
other than designated parts may damage this unit
internally or may not securely install the unit in place. This
may cause parts to become loose resulting in hazards or
product failure.
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR
PINCHED BY A SHARP METAL EDGE.
Route the cables and wiring away from moving parts (like
the seat rails) or sharp or pointed edges. This will prevent
crimping and damage to the wiring. If wiring passes
through a hole in metal, use a rubber grommet to prevent
the wire’s insulation from being cut by the metal edge of
the hole.
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE
OR DUST.
Avoid installing the unit in locations with high incidence of
moisture or dust. Moisture or dust that penetrates into this
unit may result in product failure.
NOTICE
Product Cleaning
Use a soft dry cloth for periodic cleaning of the product. For
more severe stains, please dampen the cloth with water
only. Anything else has the chance of dissolving the paint or
damaging the plastic.
Temperature
Be sure the temperature inside the vehicle is between
+45°C (+113°F) and 0°C (+32°F) before turning your unit on.
Maintenance
If you have problems, do not attempt to repair the unit
yourself. Return it to your Alpine dealer or the nearest
Alpine Service Station for servicing.
Protecting the USB connector
• Only an iPhone or USB flash drive can be connected to
the USB connector on this unit. Correct performance
using other USB products cannot be guaranteed.
• If the USB connector is used, be sure to use only the
supplied connector cable with the unit. A USB hub is not
supported.
• Depending on the connected USB flash drive, the unit
may not function or some functions may not be
performed.
• The audio file formats that can be played on the unit is
MP3/WMA/AAC/FLAC/WAV/APE.
• Artist/song name, etc., can be displayed. Certain, special
characters may not be correctly displayed.

ALPINE iLX-F509E 68-41657Z84-A (EN)ALPINE iLX-F509E 68-41657Z84-A (EN)
9-EN
CAUTION
Alpine accepts no responsibility for lost data,
etc., even if data, etc., is lost while using this
product.
On Handling USB Flash drive
• This unit can control a memory storage device that
supports the USB Mass Storage Class (MSC) protocol.
Playable audio file formats are MP3, WMA, AAC, FLAC,
WAV and APE.
• USB Flash drive function is not guaranteed. Use a USB
flash drive according to the terms of agreement. Read the
USB flash drive Owner’s Manual thoroughly.
• Avoid usage or storage in the following locations:
Anywhere in the car exposed to direct sunlight or high
temperatures.
Anywhere the possibility of high humidity or corrosive
substances are present.
• Fix the USB flash drive in a location where driver
operation will not be hindered.
• USB Flash drive may not function correctly at high or low
temperature.
• Use only certified USB flash drive. Note that even certified
USB flash drive, may not function correctly depending on
its type or state.
• Depending on the settings of the USB flash drive type,
memory state or encoding software, the unit may not
play back or display properly.
• USB Flash drive may take time to start playback. If there is
a particular file other than audio in the USB flash drive, it
may take considerable time before the file is played back
or searched.
• The unit can play back “mp3,”“wma,”“m4a,”“flac,” ”fla,”
“wav,” and “ape” file extensions.
• Do not add the above extensions to a file other than
audio data. This non-audio data will not be recognized.
The resulting playback may contain noise that can
damage speakers and/or amplifiers.
• It is recommended to back up important data on a
personal computer.
• Do not remove the USB device while playback is in
progress. Change SOURCE to something other than USB,
then remove the USB device to prevent possible damage
to its memory.
• Windows Media, and the Windows logo are trademarks,
or registered trademarks of Microsoft Corporation in the
United States and/or other countries.
• Apple, iPhone, iPod, Lightning and Siri are trademarks of
Apple Inc., registered in the U.S. and other countries.
App Store is a service mark of Apple Inc.
• Use of the Made for Apple and Works with Apple badges
means that an accessory has been designed to connect
specifically to the Apple product(s) identified in the Made
for Apple badge and to work specifically with the
technology identified in the Works with Apple badge, and
has been certified by the developer to meet Apple
performance standards. Apple is not responsible for the
operation of this device or its compliance with safety and
regulatory standards.
Please note that the use of this accessory with an Apple
product may affect wireless performance.
• Use of the Apple CarPlay logo means that a vehicle user
interface meets Apple performance standards. Apple is
not responsible for the operation of this vehicle or its
compliance with safety and regulatory standards. Please
note that the use of this product with iPhone may affect
wireless performance.
• Google, Android, Google Play and Android Auto are
trademarks of Google LLC.
To use Android Auto on your car display, you’ll need an
Android phone running Android 6.0 or higher, an active
data plan, and the Android Auto app.
• The terms HDMI and HDMI High-Definition Multimedia
Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing, LLC in the
United States and other countries.
• The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth SIG, Inc. and any use
of such marks by ALPS ALPINE Co., LTD. is under license.
Other trademarks and trade names are those of their
respective owners.
• The Wi-Fi CERTIFIED™ Logo is a registered trademark of
Wi-Fi Alliance®.
• LDAC and LDAC logo are trademarks of Sony Corporation.
• The product with this logo is conformed to High-
Resolution Audio standard defined by Japan Audio
Society. This logo is used under license from Japan Audio
Society.
Made for iPhone SE (2nd generation), iPhone 11 Pro Max,
iPhone 11 Pro, iPhone 11, iPhone XS Max, iPhone XS, iPhone
XR, iPhone X, iPhone 8 Plus, iPhone 8, iPhone 7 Plus, iPhone
7, iPhone SE, iPhone 6s Plus, iPhone 6s.
ARRANGE THE WIRING SO IT IS NO
PINCHED BY A SHARP METAL EDGE.
Route the cables and wiring away from mo
the seat rails) or sharp or pointed edges. T
crimping and damage to the wiring. If wir
through a hole in metal, use a rubber grommet t
the wire’s insulation from being cut b
the hole.
DO NOT INSTALL IN LOCATIONS
OR DUST.
Avoid installing the unit in loca
moisture or dust. Moisture or dust that penetrat
unit may result in product failure.
NOTICE
Product Cleaning
Use a soft dry cloth for periodic cleaning of the pr
more severe stains ,
p
l
e
a
s
e
d
a
m
p
e
n
t
h
e
c
l
o
t
h
w
i
t
h
w
a
t
e
r
only. Anything else has the chanc
damaging the plastic.
Temperature
Be sure the temperature inside the vehicle is bet
+45°C (+113°F) and 0°C (+32°F) before turning y
Maintenance
If you have problems, do not attempt to r e
p
ai
r
t
h
e
u
ni
yourself. Return it to your A
Alpine Service Station for servicing.
Protecting the USB connector
• Only an iPhone or USB flash drive can be c
the USB connector on this unit. Correct perfor
using other USB products cannot be guarant
• If the USB connector is used, be sure t
supplied connector cable with the unit
supported.
• Depending on the connected USB flash drive
may not function or some functions may not be
performed.
• The audio file formats that can be play e
d
o
n
t
h
e
u
n
i
t
i
s
MP3/WMA/AAC/FLAC/WAV/APE.
• Artist/song name, etc., can be displayed. Cer
characters may not be correctly displayed.

ALPINE iLX-F509E 68-41657Z84-A (EN)
10-EN
Getting Started
Location of Controls
iLX-507E
iLX-F509E/iLX-F511E
Dimmer Sensor
Senses the brightness of the car interior.
button
Activate Siri function or voice recognition mode while
Apple CarPlay or Android Auto is connected.
/ (DOWN/UP) button
Adjusts the volume.
(MUTE) button
Activates/deactivates MUTE mode.
Press and hold this button for at least 2 seconds to turn
o the screen/button illumination.
(Audio) button
Displays the Audio playback screen.
Audio sources can be switched while the Audio playback
screen is displayed.
Power indicator
(HOME) button
Displays the HOME screen.
The Sound Setup screen is displayed while the HOME
screen is displayed.
Press and hold this button for at least 2 seconds to turn
the power o.
(CAM) button
Displays the image of Camera2 (Front/Side/Other) or
Camera1 (Rear).
Press for 1 second or more to return to the previous
screen.
/ button
Press to seek up/down a station in radio mode or up/
down a track, etc., in other audio/visual sources.
(MAP) button
Displays the map screen for Apple CarPlay / Android
Auto when Apple CarPlay or Android Auto is connected.
Remote Sensor
Point the remote control transmitter towards the remote
sensor within a range of 2 meters.
About the button descriptions used in this Owner’s
Manual
The buttons found on the face of the unit are expressed
in bold (e.g. (HOME)). The buttons found on the
touch-screen display are shown in bold within brackets,
[ ] (e.g. [OK]).
CAUTION
To adjust the display angle, hold the center of the
top and bottom of the display to move it. To protect
the display, do not hold the left and right ends to
move it.

ALPINE iLX-F509E 68-41657Z84-A (EN)
11-EN
Turning Power On or O
When the ignition key is turned to ACC or ON, the opening
screen will be automatically displayed.
1 Turn the ignition key to the ACC or ON
position.
The unit turns on.
• When using the system for the rst time, the HOME
screen is displayed.
• When turned on, the unit displays the last screen that
was displayed before the ignition key was turned o.
For example, if the unit is in radio mode when ignition
is turned o, it will remain in radio mode when
ignition is turned back on.
2 To turn the unit to o, turn the ignition key to
the OFF position.
•The unit is a precision device. Careful handling of the unit
should provide you with years of trouble-free operation.
•Some of this unit’s functions cannot be performed while the
vehicle is in motion. Be sure to stop your vehicle in a safe
location and apply the parking brake before attempting these
operations.
Adjusting the Volume
Adjust the volume by touching / .
Volume decreases/increases continuously by touching and
holding / .
Volume: 0 to 35
Lowering Volume Quickly
Audio Mute function instantly lowers the volume level to 0.
1 Press the (MUTE) button to activate MUTE
mode.
The audio level will be 0 and the mute indicator will
ash.
2 Press the (MUTE) button again to bring the
audio back to previous volume level.
Turning o the Screen/Button
Illumination (Display OFF)
You can turn o the screen and button illumination without
changing the audio output.
1 Press and hold the (MUTE) button for at
least 2 seconds.
The screen/button illumination is turned o.
2 To cancel Display OFF mode, press and hold
the (MUTE) button for at least 2 seconds or
touch the screen.
•When there is an interrupt such as an incoming hands-free
call, Display OFF is canceled.
Touch Screen Operation
You can operate the unit by using the touch panel display.
• Be sure to touch the onscreen button lightly with the pad of
your nger to avoid scratching the display.
Touch operation
Touch a button or list item on the screen lightly.
•If you touch a button and there is no reaction, lift your nger.
•Onscreen buttons that cannot be operated are dimmed.
Swipe operation
Move your nger lightly with a swipe.

ALPINE iLX-F509E 68-41657Z84-A (EN)
12-EN
Switching Sources
1 Press the (HOME) button.
The HOME screen is displayed.
2 Touch your desired source icon.
•In the HOME screen, you can change the audio source icon
location on the screen. For details, see “Editing HOME screen”
(page 25).
Selecting an Item in a List
To scroll through a list, perform the following operations.
Touch the screen and slide your nger up and
down.
The screen will scroll along with your nger movement.
Returns to the previous screen.
Closes the window.
•After touching the screen, move your nger away from the
screen before dragging and that item will be selected.
About the HOME Screen
In the HOME screen, select the audio source to perform
various settings and operations of the function.
•The HOME screen can be switched between Normal mode
and Enhanced Text mode. For details, see “Setting the Home
Screen Type” (page 24).
Press the (HOME) button.
The HOME screen is displayed.
Normal mode screen example
Enhanced Text mode screen example
Touch to display the Sound Setup screen.
•The Sound Setup screen can also be displayed by
pressing the (HOME) button while the HOME
screen is displayed.
Touch to change the page.
•Pages can also be changed by swiping the HOME
screen horizontally with your nger.
Audio source select area
Touch your desired source icon to change the audio
source.
• The order of source icons can be changed. For details,
see “Editing HOME screen”(page 25).
HOME screen navigation
Thumbnail window for the current source
Source name, artwork and title information are
displayed. Touch the artwork to display the source
screen. Touch [ ] to play/pause a track or video.

ALPINE iLX-F509E 68-41657Z84-A (EN)ALPINE iLX-F509E 68-41657Z84-A (EN)
13-EN
■Normal mode screen example
■Enhanced Text mode screen example
Touch to display the Sound Setup scr
•The Sound Setup screen can also be display
pressing the (HOME) butt
screen is displayed.
Touch to change the page.
•Pages can also be changed b
screen horizontally with your finger.
Audio source select area
Touch your desired source icon t
source.
•The order of source icons can be changed. F
see“Editing HOME screen”(page 25).
HOME screen navigation
Thumbnail window for the current sour
Source name, artwork and title information ar
displayed. Touch the artwork to displa
screen. Touch [ ] to play/pause a tr
About the Indicator Display
The Indicator Bar at the top of the screen displays various
types of information, like the current time.
Phone shortcut button
The Device List screen is displayed when a Phone,
CarPlay or Android Auto device is not connected.
The hands-free phone screen (Recent Call, Phone Book,
Keypad) is displayed when the hands-free phone is
connected. The screen of the previous logout is
displayed.
The Apple CarPlay screen is displayed while Apple
CarPlay is connected.
The Android Auto screen is displayed while Android
Auto is connected.
Lights up when connecting the hands-free
phone via Bluetooth. (Does not display when
connection is set to OFF.)
Indicates the battery level of the connected
hands-free phone .
No
Battery Level 1 Level 2 Level 3 Level 4 Level 5
•This may not be displayed for the hands-free phone .
Indicates the Bluetooth signal strength level of
the connected hands-free phone .
Displayed when Bluetooth setting is ON.
012345
•This may not be displayed for the hands-free phone .
Lights up when connecting the audio device via
Bluetooth. (Does not display when connection is
set to OFF.)
Lights up when connecting the hands-free
phone via Bluetooth. (Does not display when
connection is set to OFF.)
Lights up when connecting a separately sold
ALPINE KNOB (RUE-BK01E) via Bluetooth. You can
use the RUE-BK01E to adjust the volume level
and sound quality (Bass Level, etc.) of this unit.
For details, refer to the Owner’s Manual of
RUE-BK01E.
Indicates the current time.
Touch to turn ON/OFF the clock display.
You can switch between the 12 hour display and 24 hour
display options (page 24).
Setup
Setup Operation
1 Press the (HOME) button.
The HOME screen is displayed.
[Setup] button
2 Touch [Setup].
The Settings menu screen is displayed.
3 Touch the required setting category on the
upper part of the Settings menu screen, and
then touch the setting item.
Setting categories:
Device: See “Device Setup”(page 14)
Function: See“Function Setup” (page 16)
System: See“System Setup”(page 23)

ALPINE iLX-F509E 68-41657Z84-A (EN)ALPINE iLX-F509E 68-41657Z84-A (EN)
14-EN
Device Setup
[Device] is selected on the Settings menu screen.
■Device Setup Menu screen
Setting items:
Device List (page 14)
Wi-Fi (page 15)
Bluetooth (page 15)
Device Info. (page 16)
Displaying Device List
[Device List] is selected on the Device Setup menu screen.
The list of devices registered or connected to this unit is
displayed. 10 devices compatible with Bluetooth and Wi-Fi,
and 1 device compatible with Apple CarPlay or Android
Auto connected via USB, can be displayed.
■Device List screen example
Add New Device
Search for Bluetooth compatible devices. For details, see
“Pairing the Bluetooth Device“ (page 14).
Function icon
: Hands Free1
: Hands Free2
: Bluetooth Audio
: Hands Free1 + Bluetooth Audio
: Hands Free2 + Bluetooth Audio
: Apple CarPlay
: Android Auto
Device Name or Device Address
Connect or disconnect the selected device. For
details, see“Connecting the Device Registered in
the Device List”,“Disconnecting the Connected
Device”(page 15).
Delete the selected device information. For
details, see“Deleting a Bluetooth Device from the
list” (page 15).
Pairing the Bluetooth® Device
Search for Bluetooth compatible devices.
Setting item:
Add New Device
1 Touch [Add New Device].
A search for devices to connect wirelessly to the unit
starts.
The Search List is displayed, and the list of searched
devices is displayed.
2 Touch a device to connect in the list.
The Select Function screen is displayed.
3 Select the function of the connecting device
on the Select Function screen, and touch [OK].
A check mark is displayed for the selected function.
Hands Free1: The device is used as the first
hands-free phone.
Hands Free2: The device is used as the second
hands-free phone.
Bluetooth Audio: The device is used as a Bluetooth
Audio device.
Apple CarPlay*: The device is used as Apple CarPlay.
*If you want to use Apple CarPlay mode without
displaying [Apple CarPlay] on the Select Function
screen, select [Hands Free1] or [Hands Free2] to
connect your device.
• For example, when the device is used as a hands-free
phone and Bluetooth Audio, select [Hands Free1]
and [Bluetooth Audio].
• If you want to use Apple CarPlay with a wireless
connection, set the Wi-Fi function of your iPhone to
“ O n ”.
ode is displayed on the device, check
ode is the same as the one on the
, and touch [Yes].
e connection is complete, a message
e returns to normal mode.
ting the Device Registered in
vice List
ed Bluetooth or Wi-Fi compatible
t you previously registered.
Connect] of the device you want to
t from the Paired Device list.
tion Select screen is displayed.
tion of the connecting device
unction Select screen, and touch [OK].
k is displayed for the selected function.
e connection is complete, a message
e returns to normal mode.
ting the Connected Device
isconnect] of the device you want to
t from the Paired Device list.
onnected.
ooth Device from the
e the information of a previously connected
ompatible device.
] (Delete) of the Bluetooth
tible device to delete from the Paired
e list.
Yes].
] will cancel the setting.

ALPINE iLX-F509E 68-41657Z84-A (EN)ALPINE iLX-F509E 68-41657Z84-A (EN)
15-EN
Connect or disconnect the select
details, see“Connecting the Device Reg
the Device List”,“Disconnecting the C
Device”(page 15).
Delete the selected device informa
details, see“Deleting a Bluetooth Devic
list” (page 15).
Pairing the Bluetooth® Device
Search for Bluetooth compatible devices.
Setting item:
Add New Device
1Touch [Add New Device].
A search for devices to connect wirelessly t
starts.
The Search List is displayed
devices is displayed.
2Touch a device to connect in the list.
The Select Function screen is displayed.
3Select the function of the connec
on the Select Function screen, and t
A check mark is displayed for the select
Hands Free1: The devic
hands-free phone.
Hands Free2: The devic
hands-free phone.
Bluetooth Audio: The devic
Audio device.
Apple CarPlay*: The device is used as A
*If you want to use Apple CarPla
displaying [Apple CarPlay] on the Select F
screen, select [Hands Free1] or [Hands Fr
connect your device.
• For example, when the devic
phone and Bluetooth Audio, select [
and [Bluetooth Audio].
• If you want to use Apple CarPlay with a wir
connection, set the Wi-Fi function of your iP
“ O n ”.
4 When a code is displayed on the device, check
that the code is the same as the one on the
screen of the unit, and touch [Yes].
When the device connection is complete, a message
appears and the device returns to normal mode.
Connecting the Device Registered in
the Device List
Select one of 10 paired Bluetooth or Wi-Fi compatible
devices that you previously registered.
1 Touch [Connect] of the device you want to
connect from the Paired Device list.
The Function Select screen is displayed.
2 Select the function of the connecting device
on the Function Select screen, and touch [OK].
A check mark is displayed for the selected function.
When the device connection is complete, a message
appears and the device returns to normal mode.
Disconnecting the Connected Device
Touch [Disconnect] of the device you want to
disconnect from the Paired Device list.
The device is disconnected.
Deleting a Bluetooth Device from the
list
You can delete the information of a previously connected
Bluetooth compatible device.
1 Touch [ ] (Delete) of the Bluetooth
compatible device to delete from the Paired
Device list.
2 Touch [Yes].
• Touching [No] will cancel the setting.
Wi-Fi Setup
[Wi-Fi] is selected on the Device Setup menu screen.
Setting the Wi-Fi
Set to [On] when using Apple CarPlay with a wireless
connection.
Setting item:
Wi-Fi
Touch [ ] (Off) or [ ] (On) of“Wi-Fi”.
Bluetooth Setup
[Bluetooth] is selected on the Device Setup menu screen.
Setting the Bluetooth
Set to [On] when connecting the unit to the Bluetooth
compatible device.
Setting item:
Bluetooth
Touch [ ] (Off) or [ ] (On) of
“Bluetooth”.
Setting the Auto Connection
You can connect the last connected device automatically.
Setting item:
Auto Connection
Touch [ ] (Off) or [ ] (On) of“Auto
Connection”.
Setting the PIN Code
You can set the PIN code for connecting with a BLUETOOTH
compatible device.
Setting item:
Bluetooth PIN Code
1 Touch [Bluetooth PIN Code].
A numeric keypad screen is displayed.
2 Touch [Delete All].
The displayed PIN code is cleared, then you can enter
the new PIN code.
3 Enter a 4-digit passcode, and then touch [OK].
• The initial number is 0000.
• Touch [ ] to delete an entered number.
• Touch [Delete All] to delete all entered numbers.

ALPINE iLX-F509E 68-41657Z84-A (EN)ALPINE iLX-F509E 68-41657Z84-A (EN)
16-EN
Displaying Device Information
You can display the Bluetooth or Wi-Fi device name and
device address of this unit.
Setting item:
Device Info.
Function Setup
[Function] is selected on the Settings menu screen.
■Function Setup Menu screen
Setting items*:
Apple CarPlay (page 16)
Android Auto (page 17)
Radio (page 18)
USB (page 18)
iPod (page 19)
Auxiliary (page 19)
HDMI (page 20)
Phone (page 20)
Bluetooth Audio (page 15)
Camera (page 21)
∗ Dash Cam is displayed in the setting item, but this unit
does not support it.
Apple CarPlay Setup
[CarPlay] is selected on the Function Setup Menu screen.
Adjusting the Media Level
Setting item:
Media
Setting level:
-14 to +14 (Initial setting: 0)
Touch [ ] or [ ] of “Media”to set the media
volume level for CarPlay playback.
alls Volume
alls
el:
nitial setting: 5)
] or [ ] of “Phone Calls”to set the calls
vel.
ingtones and Alerts
lerts
el:
nitial setting: 5)
] or [ ] of “Ringtones & Alerts” to set
vel for Ringtones and Alerts.
otifications and
e Level
tions & Guidance
el:
nitial setting: 10)
] or [ ] of “Notifications & Guidance”
olume level for Notifications and
.
Voice Recognition Level
ecognition
el:
nitial setting: 10)
] or [ ] of “Voice Recognition” to set
vel for voice recognition.
icrophone Level
evel
el:
nitial setting: 5)
] or [ ] of “Microphone Level” to set
olume level.

ALPINE iLX-F509E 68-41657Z84-A (EN)ALPINE iLX-F509E 68-41657Z84-A (EN)
17-EN
Function Setup
[Function] is selected on the Settings menu scr
■Function Setup Menu screen
Setting items*:
Apple CarPlay (page 16)
Android Auto (page 17)
Radio (page 18)
USB (page 18)
iPod (page 19)
Auxiliary (page 19)
HDMI (page 20)
Phone (page 20)
Bluetooth Audio (page 15)
Camera (page 21)
∗Dash Cam is displayed in the setting it
does not support it.
Apple CarPlay Setup
[CarPlay] is selected on the Function Setup M
Adjusting the Media Level
Setting item:
Media
Setting level:
-14 to +14 (Initial setting: 0)
Touch [ ] or [ ] of “Media”t
volume level for CarPlay playback.
Adjusting the Phone Calls Volume
Setting item:
Phone Calls
Setting level:
1 to 35 (Initial setting: 5)
Touch [ ] or [ ] of “Phone Calls” to set the calls
volume level.
Adjusting the Ringtones and Alerts
Level
Setting item:
Ringtones & Alerts
Setting level:
1 to 11 (Initial setting: 5)
Touch [ ] or [ ] of “Ringtones & Alerts” to set
the volume level for Ringtones and Alerts.
Adjusting the Notifications and
Guidance Level
Setting item:
Notifications & Guidance
Setting level:
1 to 35 (Initial setting: 10)
Touch [ ] or [ ] of “Notifications & Guidance”
to set the volume level for Notifications and
Guidance.
Adjusting the Voice Recognition Level
Setting item:
Voice Recognition
Setting level:
1 to 35 (Initial setting: 10)
Touch [ ] or [ ] of “Voice Recognition” to set
the volume level for voice recognition.
Adjusting the Microphone Level
Setting item:
Microphone Level
Setting level:
1 to 11 (Initial setting: 5)
Touch [ ] or [ ] of “Microphone Level”to set
the microphone volume level.
Android Auto Setup
[Android Auto] is selected on the Function Setup Menu
screen.
Adjusting the Media Level
Setting item:
Media
Setting level:
-14 to +14 (Initial setting: 0)
Touch [ ] or [ ] of “Media”to set the media
volume level for CarPlay playback.
Adjusting the Phone Calls Volume
Setting item:
Phone Calls
Setting level:
1 to 35 (Initial setting: 5
Touch [ ] or [ ] of “Phone Calls” to set the calls
volume level.
Adjusting the Ringtones and Alerts
Level
Setting item:
Ringtones & Alerts
Setting level:
1 to 11 (Initial setting: 5)
Touch [ ] or [ ] of “Ringtones & Alerts” to set
the volume level for Ringtones and Alerts.
Adjusting the Notifications and
Guidance Level
Setting item:
Notifications & Guidance
Setting level:
1 to 35 (Initial setting: 10)
Touch [ ] or [ ] of “Notifications & Guidance”
to set the volume level for Notifications and
Guidance.

ALPINE iLX-F509E 68-41657Z84-A (EN)ALPINE iLX-F509E 68-41657Z84-A (EN)
18-EN
Adjusting the Voice Recognition Level
Setting item:
Voice Recognition
Setting level:
1 to 35 (Initial setting: 10)
Touch [ ] or [ ] of “Voice Recognition” to set
the volume level for voice recognition.
Adjusting the Microphone Level
Setting item:
Microphone Level
Setting level:
1 to 11 (Initial setting: 5)
Touch [ ] or [ ] of “Microphone Level”to set
the microphone volume level.
Radio Setup
[Radio] is selected on the Function Setup Menu screen.
Adjusting the Radio Volume
Setting item:
Volume Adjust
Setting level:
-14 to +14 (Initial setting: 0)
Touch [ ] or [ ] of “Volume Adjust” to set the
radio volume level.
USB Setup
[USB] is selected on the Function Setup Menu screen.
Adjusting the USB Volume
Setting item:
Volume Adjust
Setting level:
-14 to +14 (Initial setting: 0)
Touch [ ] or [ ] of “Volume Adjust” to set the
volume level for USB Audio/USB Video playback.
Video Setup
Setting item:
Video Setup
Touch [ ] or [ ] of “Brightness, Colour,
Contrast” to set the picture quality.
•Available only when the current source is USB Video.
Adjusting Brightness
Setting item:
Brightness
Setting contents:
-15 to +15 (Initial setting: 0)
Adjusting Colour of Picture
Setting item:
Colour
Setting contents:
0 to 2 (Initial setting: 0)
Adjusting Image Contrast
Setting item:
Contrast
Setting contents:
-15 to +15 (Initial setting: 0)
ted on the Function Setup Menu screen.
od Volume
djust
el:
nitial setting: 0)
] or [ ] of “Volume Adjust” to set the
vel for iPod playback.
uxiliary) Setup
is selected on the Function Setup Menu screen.
UX Volume
djust
el:
nitial setting: 0)
] or [ ] of “Volume Adjust” to set the
vel for AUX playback.

ALPINE iLX-F509E 68-41657Z84-A (EN)ALPINE iLX-F509E 68-41657Z84-A (EN)
19-EN
USB Setup
[USB] is selected on the Function Setup Menu scr
Adjusting the USB Volume
Setting item:
Volume Adjust
Setting level:
-14 to +14 (Initial setting: 0)
Touch [ ] or [ ] of “Volume Adjust” t
volume level for USB Audio/USB V
Video Setup
Setting item:
Video Setup
Touch [ ] or [ ] of “Brightness, Colour,
Contrast” to set the picture quality.
•Available only when the current source is USB Vid
Adjusting Brightness
Setting item:
Brightness
Setting contents:
-15 to +15 (Initial setting: 0)
Adjusting Colour of Picture
Setting item:
Colour
Setting contents:
0 to 2 (Initial setting: 0)
Adjusting Image Contrast
Setting item:
Contrast
Setting contents:
-15 to +15 (Initial setting: 0)
iPod Setup
[iPod] is selected on the Function Setup Menu screen.
Adjusting the iPod Volume
Setting item:
Volume Adjust
Setting level:
-14 to +14 (Initial setting: 0)
Touch [ ] or [ ] of “Volume Adjust” to set the
volume level for iPod playback.
AUX (Auxiliary) Setup
[Auxiliary] is selected on the Function Setup Menu screen.
Adjusting the AUX Volume
Setting item:
Volume Adjust
Setting level:
-14 to +14 (Initial setting: 0)
Touch [ ] or [ ] of “Volume Adjust” to set the
volume level for AUX playback.
Setting the Auxiliary (AUX) Name
Set the display name of an external device. This name is
displayed as a source name on the HOME screen or Audio
screen.
Setting item:
AUX Name
Setting contents:
Off / Auxiliary (Initial setting) / Digital TV
•Not available when the current source is Auxiliary (or Digital
TV).
Video Setup
Setting item:
Video Setup
Touch [ ] or [ ] of “Brightness, Colour,
Contrast” to set the picture quality.
•Available only when the current source is Auxiliary (or Digital
TV).
Adjusting Brightness
Setting item:
Brightness
Setting contents:
-15 to +15 (Initial setting: 0)
Adjusting Colour of Picture
Setting item:
Colour
Setting contents:
0 to 2 (Initial setting: 0)
Adjusting Image Contrast
Setting item:
Contrast
Setting contents:
-15 to +15 (Initial setting: 0)

ALPINE iLX-F509E 68-41657Z84-A (EN)ALPINE iLX-F509E 68-41657Z84-A (EN)
20-EN
HDMI Setup
[HDMI] is selected on the Function Setup Menu screen.
Adjusting the HDMI Volume
Setting item:
Volume Adjust
Setting level:
-14 to +14 (Initial setting: 0)
Touch [ ] or [ ] of “Volume Adjust” to set the
volume level for HDMI playback.
Setting the HDMI Name
You can set the name of an external device connected via
HDMI.
Setting item:
HDMI Name
Setting contents:
Off / HDMI (Initial setting) / Digital TV
•Not available when the current source is HDMI (or Digital
TV).
Video Setup
Setting item:
Video Setup
Touch [ ] or [ ] of “Brightness, Colour,
Contrast” to set the picture quality.
•Available only when the current source is HDMI (or Digital
TV).
Adjusting Brightness
Setting item:
Brightness
Setting contents:
-15 to +15 (Initial setting: 0)
Adjusting Colour of Picture
Setting item:
Colour
Setting contents:
0 to 2 (Initial setting: 0)
Adjusting Image Contrast
Setting item:
Contrast
Setting contents:
-15 to +15 (Initial setting: 0)
Setting the HDMI Selector
Set to On when the optional HDMI Selector is connected.
Setting item:
HDMI Selector
Touch [ ] (Off) or [ ] (On) of“HDMI
Selector”.
Phone Setup
[Phone] is selected on the Function Setup Menu screen.
Adjusting the Ringtone Level
Setting item:
Ring Tone Level
Setting level:
1 to 11 (Initial setting: 5)
Touch [ ] or [ ] of “Ring Tone Level”to set the
Ringtones volume level.
•Not available when Apple CarPlay or Android Auto is
connected.
Adjusting the Phone Calls Volume
Setting item:
Caller Level
Setting level:
1 to 35 (Initial setting: 5)
Touch [ ] or [ ] of “Caller Level” to set the calls
volume level.
•Not available when Apple CarPlay or Android Auto is
connected.
icrophone Level
evel
el:
nitial setting: 5)
] or [ ] of “Microphone Level” to set
olume level.
able when Apple CarPlay or Android Auto is
.
ook Transfer
o transfer the phonebook automatically.
ransfer
tents:
anual
ook Name Order
yed in
.
der
tents:
irst/Last (Initial setting)
ook Calendar
e format displayed in the phonebook.
alendar
tents:
nitial setting) / MM/DD/YYYY /
YYY