Altec Lansing inMotion iM616 User manual

USER GUIDE

2
CAUTION
Consult a physician or audiologist if you have excessive ear wax, difficulty inserting
the eartips, or discomfort after prolonged use.
inMotion earphones exclude most external sounds
even at low listening levels. It is unsafe to use insert
earphones while driving a motorized vehicle,
operating machinery, bicycling or jogging, because
you may not be alerted to potential danger.
Do not use the earphones at excessively loud levels.
Noise-induced hearing loss is a function of exposure time, the average sound level
and the peak of very loud sounds. Decreased listening levels allow for longer periods
of safe listening time.
ENGLISH

3
PROPER CARE
•Do not expose earphones to extreme temperatures.
•Avoid dropping or strong impact. Extreme shock can damage the earphones.
•Always leave an eartip on the earphone for shock protection.
•Perspiration entering the nozzle may cause the earphone to temporarily stop
working. Normal operation usually returns after the earphone dries out.
•Do not pull on the cord to remove it from the jack or the ear.
•Clean or replace the eartips prior to use by others.
•Replace disposable foam eartips regularly.
•Earwax buildup can reduce the earphone output. When the filters become
clogged they should be replaced. See Changing Filters.
ENGLISH

4
CONTENTS:
•inMotion earphones
•1pair white 3-flange eartips
•1pair foam eartips
•1pair replacement filters
•Filter changing tool
•Deluxe carry case
EARTIPS
In addition to flanged eartips, inMotion
earphones are supplied with disposable
foam eartips. Both types provide excellent
sound reproduction when properly
inserted. If the earphones seem to lack bass, insert the eartip deeper
into the ear canal to obtain a better seal, or try the foam eartip option.
ENGLISH

5
Flanged eartips
These reusable eartips should be cleaned regularly.
Cleaning the flanged eartips
1. Carefully remove the eartip from the earphone.
2. Use water and mild soap to remove dirt and earwax.
3. Rinse and completely dry the eartip.
4. With a slight twisting motion, push the eartip on the stem until it fits securely.
Foam eartips
•Disposable foam eartips compress to form a tight seal that holds the earphones
firmly in place.
•The eartips at the end of the earphones can be replaced by sliding them off and
on. A combination of twisting and pulling is recommended for eartip removal.
ENGLISH

6
EARTIP INSERTION
Flanged eartip insertion
•For best results, moisten the flanged eartip
before insertion.
•Carefully insert one earphone at a time while
pulling up and out on the back of the ear. The
earphone should seal deeply and comfortably
in the ear canal.
Foam eartip insertion
•Use a foam eartip if a good seal cannot be
obtained with a flanged eartip.
•Compress the foam at the end of the earphone by rolling it between your thumb
and forefinger before inserting it. Hold the eartip in place for about 5 seconds
while the foam expands to create a tight seal in the ear canal.
ENGLISH

7
REMOVAL
Remove earphones slowly with a twisting motion to gradually break the seal. Do not
pull on the cords to remove earphones.
iM716 CONTROLLER MODE SWITCH SETTINGS
“Bass” Position — Emphasizes low frequency and overall volume. Excellent setting
for aggressive, bass-enhanced playback.
“HD” High Definition Audio Position — Produces a flat, non-colored frequency
response. Excellent setting for the audiophile purist.
ENGLISH

8
FILTERS
inMotion earphones have special filters that smooth the frequency response and
prevent earwax from entering the earphones. These filters are located at the tip of
the earphone and are visible when the eartip is removed. If the filters become
clogged they should be replaced. A dirty filter will reduce earphone output. The
frequency with which the filters need to be changed will vary widely among users.
The filters should be changed if the volume decreases or the sound quality declines.
Note: Once removed, the filters are not reusable.
Additional replacement filters and tools are available from
www.alteclansing.com/inmotionearphones
ENGLISH

9
CHANGING FILTERS
Filter Removal
1. Remove eartip. Note the red plastic ring with a light pink filter in the center.
2. With a slow twisting motion, firmly push the sharp tip of the filter tool into the
center of the filter.
3. Pull out on the entire filter and red ring.
ENGLISH

10
Filter Replacement
1. With your fingers, put the narrow end of a new filter into the end of the
earphone. Be careful to put the open end in first so that the light pink filter can
be seen at the tip of the earphone. Gently push on the filter and snap it into the
earphone. You should feel and hear it snap in place.
2. Add the eartip back onto the earphone.
ENGLISH