Altendorf E-Cruise User manual

White/Brown
Red
Blue
Connector on the brake
Connector on the accelerator pedal
Black
Common earth connection
on the left A-pillar

Only mount this wire on
vehicles with manual transmission.
White
Yellow
Aftermarket clutch switch
Purple
White connector behind the radio
(Viewed from wire side)
White/Red
(Speed)
Red
Ground

White/Purple
Black
Connector below steering wheel
(Viewed from wire side)
In the Black wire in to the sert and White/Purple
connector 7 and 8in pin .
Placement is unimportant.
Disconnect the airbag in the manner described by TOYOTA.
Cut the template after the marked line, mount it on the right side
of the plastic cover on the steering wheel. Use a 28mm drill.
Mount the connector for the lever in place, and install the lever in
the steering wheel with the two enclosed screws.
Cut the two wires of the small 4-p connector, and solder them to the
enclosed white wires. Insert the white wires in to the connector behind
the airbag connector 7 and 8 Placement is unimportant.in pin .
Reinstall the steering wheel and reconnect the airbag.
Connector behind the airbag
(Viewed from wire side)

Reaction to the individual tests, requires that the function is active
Test 1 - Brake function. Activate RES briefly. Test LED will flash orange 1 time.
(No wires mounted on the brake connector).CANbus installation:
1. Test LED lights up Red, and changes to green when pedal is depressed.
(Wires mounted on the brake connector).Analog installation:
1. If both brake wires are installed correctly, the test LED will light up green.
2. Hot side of brake is defective = test LED lights up red.
3. Cold side of brake is defective = test LED lights up orange.
4. Both sides of brake defective = test LED flashes all 3 colors.
5. When brake pedal is depressed, the test LED lights up orange.
Test 2 - Clutch function. Activate RES briefly. Test LED will flash orange 2 times.
(No wires mounted on the clutch connector).CANbus installation:
1. Test LED lights up Red, and changes to green when pedal is depressed.
(Wires mounted on the clutch connector).Analog installation:
1. If clutch wires are installed correctly, the test LED lights up green.
2. If clutch is defective, the test LED lights up red.
3. When clutch pedal is depressed, the test LED lights up red.
Test 3 - Accelerator pedal function (engine off). Activate RES briefly. Test LED will flash orange 3 times.
1. The test LED will slowly flash red/green.
2. Depressing the accelerator pedal will increase the freq. of the flashing.
Test 4 - VSS function (engine running). Activate RES briefly. Test LED will flash orange 4 times.
CANbus installation: (Purple wire is not connected).
1. The test LED will flash green if correct ID is received.
Analog installation: (Purple wire is connected).
1. The test LED will flash green when vehicle is moved.
Test 5 - TACHO function (engine running). Activate RES briefly. Test LED will flash orange 5 times.
(Purple wire is not connected).CANbus installation:
1. The test LED will flash green if correct ID is received.
Analog installation: (Purple wire is connected).
1. The test LED will flash green when RPM is raised.
Test 6 - Setup to Automatic gear. Activate RES briefly. Test LED will flash orange 6 times.
(This point should ONLY be performed if it is described on the front page with red text).
1. Activate and hold down the brake pedal.
2. Activate SET briefly = test LED lights up red.
3. Activate SET briefly again = test LED lights up orange. E-Cruise is set for automat gear.
If this function is activated by mistake. The test procedure must be entered from start.
Setup to Manual gear.
1. Activate and hold down the brake pedal.
2. Activate SET briefly = test LED lights up green.
3. Activate SET briefly again = test LED lights up orange. E-Cruise is set for manual gear.
Put ignition on the vehicle
Within 2 seconds, press and hold the ON function
Wait until test LED lights up in RED color
Press and hold SET function
The test LED will flash in all 3 colors, p norovided that
inputs are activated.
Otherwise the test LED will light up red.
The test LED lights up in ORANGE color
Release ON function
Release SET function
Press RES function
Within 5 seconds
Within 5 seconds
ON
RES
SET
ON
RES
SET
ON
RES
SET
Enable Diagnostic mode:
12
6
39
12
6
39