Altronix eBridge Plus User manual

IP and PoE+ over Coax Solution
Installation Guide
Models Include:
eBridge8PCRM
- Eight (8) Channel Receiver
eBridge16PCRM
- Sixteen (16) Channel Receiver
Rev. 072412 More than just power.™
I.T.E. 43KC
Z1409
PLUS

- 2 - eBridge8PCRM/16PCRM
Overview:
eBridge8PCRM/16PCRM and eBridge1PCTX or eBridge1ST are CAT5 to Coax cable Ethernet adapters/Media converters
that deliver data and power over the coax cable in a PoE+ compliant format. The paired set enables fast 10/100Base-T Ethernet
digital communication to be transmitted over Coax cable. eBridge8PCRM/16PCRM receiver is powered by a UL Listed
limited power source, PoE midspan or endspan product, such as a NetWay8M and NetWay16M, and sends its power over
the coax to the eBridge1PCTX or eBridge1ST transmitter under PoE protocol. This enables the eBridge8PCRM/16PCRM to
be used in a managed manner, allowing for remote camera reset. The eBridge1PCTX or eBridge1ST, in turn, delivers that
PoE+ compliant power to a PoE enabled camera or IP device. The eBridge8PCRM/16PCRM will not deliver power to non-
compliant devices, thus avoiding damage to improperly connected analog cameras. These plug and play units facilitate system
upgrades from analog to IP cameras/devices utilizing existing legacy Coax and eliminating the costs and labor associated with
installing new network cabling. In addition, data transmission and power over the Coax is possible up to 457m in comparison
to 100m Ethernet maximum distance (see Maximum Length of Coax Type vs. Camera Power/PoE Class, pg. 3). A maximum
range from head end to the PoE camera/device is 657m taking into consideration that up to 100m of structured cable may be
deployed at each end.
Features:
Agency Listings:
• UL/CUL Listed for Information
Technology Equipment (UL 60950-1).
• CE approved.
• C-Tick compliant.
Compatible Transceivers:
• eBridge1PCTX: PoE/PoE+ compliant transceiver.
• eBridge1ST: PoE/PoE+ compliant mini transceiver.
Input:
• Powered by a UL Listed limited power source,
PoE midspan or endspan.
Ethernet:
• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair CAT5 or better structured cable.
• Distance: up to 100m.
• Speed: 10/100BaseT, half/full duplex, auto negotiation.
PoE compliant to IEEE 802.3af (15W) and PoE+
compliant to IEEE 802.3at (30W) delivered to camera by
eBridge1PCTX or eBridge1ST. Power provided by
eBridge8PCRM/16PCRM to eBridge1PCTX or
eBridge1ST by PoE protocol.
• Throughput is rated to pass 25mbps of data at distances
up to 500m. With proper headend equipment this
supports Megapixel, HD720, HD1080.
Coax:
• Distance: up to 500m (see Maximum Length of Coax
Type vs. Camera Power/PoE Class, pg. 4) for power
delivery of coax.
• Connectivity: BNC, RG-59/U or similar.
LED Indicators:
• eBridge8PCRM/16PCRM:
Blue LED - Coax link connection.
Green - PoE ON.
Green - Power ON.
• eBridge8PCRM/16PCRM, eBridge1PCTX, eBridge1ST:
Yellow and Green LED (RJ45) IP Link status,
10/100Base-T/active.
LED Indicators (cont’d):
• eBridge1PCTX and eBridge1ST:
Blue LED - Coax link connection.
Green LED - PoE from eBridge8PCRM/16PCRM.
Environmental:
• Operating Temperature:
eBridge8PCRM/16PCRM:
-20ºC to 49ºC (-4ºF to 120.2ºF).
eBridge1PCTX:
For 15W: -40ºC to 75ºC (-40ºF to 167ºF).
For 30W: -40ºC to 49ºC (-40ºF to 120.2ºF).
eBridge1ST:
For 15W: -40ºC to 75ºC (-40ºF to 167ºF).
For 30W: -40ºC to 65ºC (-40ºF to 149ºF).
• Storage Temperature: -30º to 70ºC (-22º to 158ºF).
• Humidity: 20 to 85%, non-condensing.
Functions:
• Auto detection and protection of legacy
non-PoE cameras/devices.
Applications:
• Retrofit digital IP cameras in an analog
CCTV installation.
• Works with Megapixel, HD720, HD1080 and VGA
(SD) cameras (see note, pg. 2).
• Extend Network link distance in an industrial
environment over 610m (see note, pg. 2).
• Upgrade deployed CCTV Coax to a digital network
in Retail, Hospitality, Arenas, Casinos, Airports,
Schools, Hospitals, Transportation, etc.
Mechanical:
• Dimensions (H x W x D approx.):
eBridge8PCRM/16PCRM dimensions:
1.625” x 19.125” x 8.5” (42mm x 486mm x 216mm)
eBridge1PCTX dimensions:
1” x 2.5” x 4.375” (25.4mm x 63.5mm x 111.125mm).
eBridge1ST dimensions:
2.27” x 2.645” x 1.12” (57.66mm x 67.18mm x 28.44mm).

eBridge8PCRM/16PCRM - 3 -
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and
authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application.
eBridge8PCRM/16PCRM is not intended to be connected to outside plant leads and should be installed indoors within the
protected premises. The eBridge8PCRM/16PCRM and eBridge1PCTX are intended for indoor use only.
Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the
rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment
in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe
operation of the equipment is not compromised. Do not obstruct any air vents on the unit. It is recommended to leave half
space above and below the unit.
Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due
to uneven mechanical loading.
Circuit Overloading - Consideration should be given to the connection of the equipment to supply circuit and the effect that
overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment
nameplate rating should be used when addressing this concern.
Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given
to supply connections other than direct connections to the branch circuit (e.g. use of power strips).
1. eBridge8PCRM/16PCRM installation:
a. Attach mounting brackets to eBridge8PCRM/16PCRM unit for rack installation (Fig. 4, pg. 7).
Affix rubber pads to eBridge8PCRM/16PCRM for shelf installation (Fig. 5, pg. 7).
Unit should be located in proximity to ethernet switch/network, NVR or video server.
b. Connect structured cable from ethernet midspan or endspan device to RJ45 jack marked [10/100BaseT]
(Fig. 2, pg. 4).
c. Connect Coax cable to BNC connector marked [Coax] (Fig. 1, pg. 4).
2. eBridge1PCTX installation:
a. Secure unit to desired mounting surface with a proper fastening device utilizing the case’s mounting hole.
Unit should be mounted in proximity of camera/device.
b. Connect structured cable from IP camera/device to RJ45 jack marked [10/100BaseT] (Fig. 2, pg. 4).
c. Connect Coax cable to BNC connector marked [Coax] (Fig. 2, pg. 4).
3. eBridge1ST installation:
a. Secure unit to the desired mounting surface with a proper fastening device utilizing the case’s mounting hole
(Fig. 3, pg. 5). Unit should be mounted in proximity of camera/device.
b. Connect structured cable from IP camera/device to RJ45 jack marked [PoE Out] (Fig. 2a, pg. 4).
c. Connect Coax cable from eBridge8PCRM/16PCRM to BNC tether cable marked [Coax] (Fig. 2a, pg. 4).
Note: eBridge8PCRM/16PCRM is designed to accommodate Megapixel, HD720, HD1080 and VGA (SD) cameras. It is
important to note that some high resolution and high frame rate cameras may demand faster headend processing ability,
such as a PC graphics card to present a quality image. If the headend processing equipment is insufficient in speed, the
image may show pixelation and latency. It is advisable to pretest system if unsure. Alternatively, frame rate and resolution
may be reduced to accommodate system equipment.

- 4 - eBridge8PCRM/16PCRM
Data In Data In
12345678
10/100
Base-T
1234
10/100
Base-T
5678
eBridge8PCRM (rear)
eBridge8PCRM (front) Structured
Cable from
midspan/endspan
Coax
Cable from
eBridge1PCT or
eBridge1PCTX
Data In Data In Data In Data In
12345678910111213141516
10/100
Base-T
1234
10/100
Base-T
5678
10/100
Base-T
910111213141516
eBridge16PCRM (rear)
eBridge16PCRM (front) Structured
Cable from
midspan/endspan
Coax
Cable from
eBridge1PCT or
eBridge1PCTX
Fig. 1a eBridge16PCRM
Fig. 1 eBridge8PCRM
Green LED
indicates
Power
Structured
Cable from
IP Camera/Device
Blue LED
indicates
Coax Connection
Coax
Cable from
eBridge8PCRM/16PCRM
Fig. 2 eBridge1PCTX
Fig. 2a eBridge1ST
Front Rear
Structured
Cable from
Camera/Device
Green LED
indicates
PoE Out
to Device
Flying BNC
Connector
Blue LED
indicates
Coax Link
is active
Flying BNC
Connector

eBridge8PCRM/16PCRM - 5 -
Multiple PoE Camera Connection:
eBridge8PCRM shown. eBridge16PCRM is similar, with twice as many channels.
Fig. 3
PoE Camera
PoE Camera
PoE Camera
PoE Camera
PoC (PoE+ over Coax)
457m max.
PoC (PoE+ over Coax)
457m max.
PoC (PoE+ over Coax)
457m max.
PoC (PoE+ over Coax)
457m max.
100m max.
100m max.
100m max.
100m max.
100m max.
100m max.
100m max.
100m max.
PoE compliant
100m max.
PoE compliant
100m max.
PoE compliant
100m max.
PoE compliant
100m max.
Coax
Structured Cable
Legend:
Transceiver
Transceiver
Transceiver
Transceiver
PoE Camera
PoE Camera
PoE Camera
PoE Camera
PoC (PoE+ over Coax)
457m max.
PoC (PoE+ over Coax)
457m max.
PoC (PoE+ over Coax)
457m max.
PoC (PoE+ over Coax)
457m max.
PoE compliant
100m) max.
PoE compliant
100m max.
PoE compliant
100m max.
PoE compliant
100m max.
Transceiver
Transceiver
Transceiver
Transceiver
eBridge1PCTX
or
eBridge1ST
eBridge8PCRM
Powered Switch or NetWay MidSpan

- 6 - eBridge8PCRM/16PCRM
Technical Specifications:
Parameter Description
Connections BNC for Coax link. RJ45 for ethernet link.
Input power
requirements Midspan or endspan port connected.
Indicators
Blue: Coax Link.
Yellow (RJ45 connector): On - Link, Off - No Link, Blinking - Activity.
Green (RJ45 connector): On - 100Base-TX, Off - 10Base-T.
Green: Power.
Environmental
Conditions
Operating Ambient Temperature: UL60950-1
eBridge8PCRM/16PCRM: -20ºC to 49ºC (-4ºF to 120.2ºF).
eBridge1PCTX: For 15W: -40ºC to 75ºC (-40ºF to 167ºF).
For 30W: -40ºC to 49ºC (-40ºF to 120.2ºF).
eBridge1ST: For 15W: -40ºC to 75ºC (-40ºF to 167ºF).
For 30W: -40ºC to 65ºC (-40ºF to 149ºF).
Storage Temperature: -30ºC to 70ºC (-22ºF to 158ºF).
Relative humidity: 20 to 85%, non-condensing.
Operating Altitude: -1000 to 6,561.679 ft. (-304.8 to 2000m).
Regulatory
Compliance
UL/CUL Listed for Information Technology Equipment (UL 60950-1).
CE approved. C-Tick compliant.
Weights (approx.) eBridge8PCRM: Product: 5.8 lbs. (2.63 kg); Shipping: 7.8 lbs. (3.54 kg)
eBridge16PCRM: Product: 7.2 lbs. (3.27 kg); Shipping: 9.2 lbs. (4.17 kg)
Maximum Length of Coax Type vs. Camera Power/PoE Class:
Camera
Power/
PoE Class
RG59/U
(23AWG)
RG59/U
(22AWG)
RG59/U
(20AWG)
RG59/U
(18AWG)
RG6/U
(18AWG)
Max. Length (meters)
13W/0 260.64m 335.28m 457.20m+ 457.20m+ 457.20m+
4W/1 457.20m+ 457.20m+ 457.20m+ 457.20m+ 457.20m+
6.5W/2 457.20m+ 457.20m+ 457.20m+ 457.20m+ 457.20m+
13W/3 260.64m 335.28m 457.20m+ 457.20m+ 457.20m+
19W 260.64m 335.28m 457.20m+ 457.20m+ 457.20m+
25W 260.64m 335.28m 457.20m+ 457.20m+ 457.20m+

eBridge8PCRM/16PCRM - 7 -
Mounting Options:
Rack Mount Installation
1- Remove and discard factory installed screws from both sides of rack chassis (Fig. 4a).
2- Install mounting brackets (A) on the left and right side of rack chassis using the
four (4) flat head screws (B) (included) (Fig. 4b).
3- Place unit into desired EIA 19” rack position and secure with mounting screws (not included) (Fig. 4c).
Fig. 4
Fig. 4a Fig. 4b Fig. 4c
Shelf Installation
1- Position and affix rubber pads (C) (included) at each
corner on the bottom of the unit (Fig. 5).
2- Place unit in desired location.
Fig. 5
B
A
C
Mounting Hardware (Included):
C
A
B
Top Top Top
Front
Left
Front
Left Front Left
Left Side
Rubber Pad
Two (2) mounting brackets
Six (6) flat head screws
for mounting brackets.
Four (4) rubber pads.
Remove

- 8 - eBridge8PCRM/16PCRM
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: [phone]
website: www.altronix.com, e-mail: [email protected]. Lifetime Warranty, Made in U.S.A.
IIeBridge8PCRM/16PCRM K218P MEMBER
Data In Data In Data In Data In
12345678910111213141516
10/100
Base-T
1234
10/100
Base-T
5678
10/100
Base-T
9101112
10/100
Base-T
13 14 15 16
8.5"
216mm
0.75"
19.05mm
19.125"
486mm
17.625"
447.7mm
1.625"
42mm
Enclosure Dimensions (H x W x D approximate):
1.625” x 19.125” x 8.5” (42mm x 486mm x 216mm)
eBridge16PCRM shown. eBridge8PCRM is similar.