Altronix Pace1KRT User manual

Overview:
Pace1KRT is a long range Ethernet adapter kit that transmits data and power via UTP (2-wire,
twisted pair) in a PoE(+) compliant format. Pace1KR receiver is powered via a PoE midspan/end-
span, such as the Altronix Netway series. The receiver passes the PoE compliant power over UTP
to the Pace1KT transceiver which, in turn, passes this power to an enabled IP camera/device. These
plug and play, cost-effective solutions facilitate IP devices that need to be installed at distances
greater such as in elevator shafts, tunnels, bridges, HVAC, etc.. supporting deployments over 1000m.
Features:
Rev. 012121
Installation Guide
Pace1KRT
Long Range Single Pair (UTP) Ethernet Adapter Kit
Kit includes Pace1KR Receiver and Pace1KT Transceiver
Input (Pace1KR Receiver):
• Powered by midspan or endspan.
PoE compliant to IEEE 802.3af (15W) and
PoE+ compliant to IEEE 802.3at (30W).
UTP Connection:
• Wire type: 2-wire (UTP).
• Speed: 10Mbps
• Distance: + 1000m, 18/2 AWG @ 10Mbps
(see Maximum Length of Cable Type vs.
Total Power Consumption, pg.3)
Ethernet Connection:
• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair CAT5e or higher.
• Distance: up to 100m from midspan to
Pace1KR receiver (headend),
100m from PaceKT transceiver to device
• Speed: 10/100BaseT, half/full duplex, auto
negotiation. PoE compliant to IEEE 802.3af
(15W) and PoE+ compliant to IEEE 802.3at
(30W) delivered to device by Pace1KR
Power provided by Pace1KR to Pace1KT
by PoE protocol.*
LED Indicators:
• Pace1KR and Pace1KT:
Link LED: Green, PoE Active
(left of UTP link)
Link LED: Green, Active Indicate
Data transmission (Next to Ethernet link)
• Pace1KR and Pace1KT: (RJ45 jack):
Yellow and Green LED IP Link status,
10/100Base-T/active.
Environmental:
• Operating Temperature:
Pace1KR / Pace1KT:
– 40ºC to 75ºC (– 40ºF to 167ºF).
• Storage Temperature:
– 40ºC to 75ºC (– 40ºF to 167ºF).
• Relative humidity:
20 to 85%, non-condensing.
Functions:
• Auto detection and protection of legacy
non-PoE cameras/devices.
Applications:
• Utilize twisted pair for new installations
or retrofit of IP devices.
• Extend Network link distance in an
industrial environment over 1000m.
• Works with Megapixel, HD720, HD1080
and VGA (SD) cameras with proper
headend equipment.
Mechanical:
• Dimensions (W x L x H approx.):
Pace1KR and Pace1KT:
3.8” x 2.5” x 1”
(96.52mm x 63.5mm x 25.4mm).
*See note on Page 3.

- 2 - Pace1KRT
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and
with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or
Recognized wire suitable for the application.
Pace1KR and Pace1KT are not intended to be connected to outside plant leads and should be
installed indoors within the protected premises. Pace1KR and Pace1KT are intended for indoor
use only.
1. Pace1KR installation:
a. Secure unit to the desired mounting surface with a proper fastening device utilizing the
unit’s mounting hole (Fig. 2a, pg. 3). Unit should be mounted in proximity to ethernet
switch/network, NVR or video server.
b. Connect structured cable from ethernet midspan or endspan device to RJ45 jack marked
[PoE Input] (Fig. 2, pg. 3).
c. UTP / 2-wire: Connect UTP to connector marked [+, –] (Fig. 2, pg. 3).
2. Pace1KT installation:
a. Secure unit to the desired mounting surface with a proper fastening device utilizing the
case’s mounting hole. Unit should be mounted in the proximity of camera/device.
b. Connect structured cable from IP camera/device to RJ45 jack marked [PoE Out] (Fig. 2, pg. 3).
c. Connect UTP to the connector marked [+, –] from receiver (Pace1KR) (Fig. 2, pg. 3).
Technical Specifications:
Parameter Description
Connections RJ45 for CAT5/6 or higher ethernet link.
UTP (2-wire) screw terminals to interconnect receiver/transceiver
Input power
requirements
Midspan or endspan port connected.
PoE compliant to IEEE 802.3af (15W) and
PoE+ compliant to IEEE 802.3at (30W)
Indicators
Yellow (RJ45 connector):On - Link, Off - No Link, Blinking - Activity.
Green (RJ45 connector):On - 100Base-TX, Off - 10Base-T.
Green Link LEDs: Link active
Environmental
Conditions
Operating Ambient Temperature: UL60950-1
Pace1KR: – 20ºC to 49ºC (– 4ºF to 120.2ºF).
Pace1KT: For 15W: – 40ºC to 75ºC (– 40ºF to 167ºF).
For 30W: – 40ºC to 49ºC (– 40ºF to 120ºF).
Storage Temperature: – 40ºC to 75ºC (– 40ºF to 167ºF).
Relative Humidity: 20 to 85%, non-condensing.
Operating Altitude: – 304.8 to 2,000m.
Regulatory
Compliance CE approved.
Weights (approx.) Product: 0.4 lbs. (0.18 kg) | Shipping: 1 lbs. (0.45 kg).
Fig. 1
Structured Cable
(CAT5 or higher)
to PoE Camera/Device
Structured Cable
(CAT5 or higher)
from Midspan/Endspan
LED indicates
Data Transmission
LED indicates
PoE being
transmitted
to transceiver
LED indicates
PoE being
transmitted
to transceiver
UTP link to Transceiver
LED indicates
Data Transmission
Pace1KR - Receiver Pace1KT- Transceiver
UTP link from Receiver

Pace1KRT - 3 -
Single PoE Camera Connection:
Fig. 2 Fig. 2a
Maximum Length of Cable Type vs. Total Power Consumption:
Wire type Total Power
Consumption
Max.
Data Distance
Max.
Power Distance
18 AWG
(2-wire, UTP)
7.5W 1000m (3280 ft) 1996m (6548ft.)
15W 1000m (3280 ft) 998m (3274 Ft.)
30W 1000m (3280 ft) 269m (882 ft)
16 AWG
(2-wire, UTP)
7.5W 1000m (3280 ft) 3169m (10396 ft.)
15W 1000m (3280 ft) 1584m (5196 ft.)
30W 1000m (3280 ft) 427m (1400 ft.)
Note: Calculations based on 56VDC starting voltage from power source and accounts for a
10VDC voltage drop. IEEE standards voltage range requirement for powered devices are:
PoE (15W) - 37VDC to 57VDC, PoE+ (30W) - 44VDC to 57VDC)
PoE/PoE+
Device
PoE+ up to 1000m
18/2 AWG, UTP CAT5e or higher
(100m)
CAT5e
(or higher)
(100m)
PoE Powered
Switch or Midspan
IP Device
PoE
Input
UTP Link
+ –
RJ45 LEDs Yellow - Activity
Green - Speed
Green LEDs Link Status
Link
LED
Link
LED
UTP Receiver
Passes PoE/PoE+
Pace1KR - Receiver
Made in U.S.A.
www.altronix.com
PoE
Output
UTP Link
+ –
Link
LED Link
LED
UTP Transceiver
Passes PoE/PoE+
Pace1KT - Transceiver
Made in U.S.A.
www.altronix.com
Mounting Hole
Pace1KR Pace1KT
RJ45 LEDs Yellow - Activity
Green - Speed
Green LEDs Link Status

- 4 - Pace1KRT
Notes:
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty | Made in U.S.A.
IIPace1KRT B19U MEMBER