Altronix Trove t2rm7f8sq User manual

T2RM7F8SQ

8 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove2R enclosure with TM2R Altronix/Mercury backplane

- One (1) eFlow104NB - Power Supply/Charger

- One (1) LINQ8ACM - Dual Input Networked Fused

Access Power Controller

- One (1) VR6 - Voltage Regulator

- One (1) PDS8 - Dual Input Fused Power Distribution Module

T2RM7F8SDQ

8 Door Kit with PTC Outputs

Fully assembled kit includes:

- Trove2R enclosure with TM2R Altronix/Mercury backplane

- One (1) eFlow104NB - Power Supply/Charger

- One (1) LINQ8ACMCB - Dual Input Networked PTC

Access Power Controller

- One (1) VR6 - Voltage Regulator

- One (1) PDS8CB - Dual Input PTC Power Distribution Module

Altronix/Mercury Networked Rack Kits

Models Include:

Rev. 060823

Installing Company: _________________________ Service Rep. Name: __________________________________________

Address: _________________________________________________________ Phone #: _________________________

All registered trademarks are property of their respective owners. More than just power.™

Installation Guide

All components of these Trove kits are UL Listed sub-assemblies.

Please refer to the included corresponding Sub-Assembly Installation Guides for further information.

Access & Power Integration

- 2 - T2RM7F8S(D)Q Installation Guide

Overview:

Altronix Trove Mercury rack kits are pre-assembled and consist of Trove enclosures/backplanes with factory installed Altronix power supply/charger

and sub-assemblies. All kits accommodate a variety of Mercury modules for up to eight doors in a single enclosure.

Configuration Chart:

Altronix

Model

Number

120VAC 60Hz

Input Current (A)

Power Supply Board

Input Fuse Rating

Power Supply Board

Battery Fuse Rating

Nominal DC

Output Voltage

Maximum Supply

Current for Main

and Aux. Outputs on

Power Supply board

and LINQ8ACM(CB)

Access Power

Controller’s outputs

Fail-Safe/Fail-Secure or

Dry Form “C” Outputs

Current Per LINQ8ACM(CB)

Output (A)

LINQ8ACM(CB) Board

Input Fuse (PTC) Rating

LINQ8ACM(CB) Board

Output Fuse (PTC) Rating

PDS8(CB) Board

Input Fuse (PTC) Rating

PDS8(CB) Board

Output Fuse (PTC) Rating

[DC] [Aux]

Output

Range

(VDC)

Output

Range

(VDC)

T2RM7F8SQ

4.5 6.3A/

250V

15A/

32V

20.17-

26.4

20.28-

26.4 24VDC @ 9.2A 8

2.5 15A/

32V

3A/

32V

10A/

32V

3A/

32V

T2RM7F8SDQ 2.0 9A 2.5A 9A 2.5A

Hardware:

Spacer | 5/16” Pan Head Screw | Lock Nut

Installing Trove2R into Rack Tower:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction.

These products are for indoor use only and must be installed within the protected premises.

Note: First assemble and Install Z Bracket Wire Management Accesory (refer to Z Bracket Installation pg. 3)

1. Remove backplane from enclosure prior to installing into rack cabinet (do not discard hardware).

2. In order to mount included cUL Listed tamper switch (Tane Model 3/8 ASH FM WH or equivalent),

turn the enclosure upside down and locate mounting holes (Fig. 1, pg. 2).

Insert the tamper switch flying leads into the center knockout of the three (3) holes from outside of the

drawer with the button facing outwards, make sure tamper switch is inserted properly then secure it

with the two (2) screws (supplied). Connect tamper switch wiring to the Access Control Panel input or

the appropriate UL Listed reporting device. To activate alarm signal open the rack drawer.

3. Slide the rack enclosure into an open 2U location in the four post rack cabinet.

4. Utilizing proper fasteners attach front ears to the rack rails (Rack drawer, pg. 8).

5. Attach the rear of the adjustable slides to the rear rails of the rack cabinet with the proper fasteners.

6. Secure the rack cover (Fig. 2a, pg. 3) and rack drawer (Fig. 2b, pg. 3) to earth ground.

7. Ensure that all internal cofigurations (voltage selection, switch settings, etc.) are completed before

mounting backplane back into Trove rack enclosure.

Fig. 1

Back of the drawer,

viewed from outside.

Tamper Switch

mounting location

Fig. 2

Fig. 2a

Fig. 2b

T2RM7F8S(D)Q Installation Guide - 3 -

Z Bracket Installation for Trove2R:

Altronix Trove2R enclosure includes Z Bracket, a convenient and reliable wire management accessory.

Hardware (included):

Twelve (12) bolts and eight (8) lock nuts.

1. Carefully unpack Z Bracket. Do not discard included hardware

(Fig. 3, pg. 3).

2. Attach arms to each other using bolts and lock nuts (Fig. 4a, pg. 3).

3. Attach the hinge brackets to the ends of arms using bolts and nuts,

positioning them as shown on (Fig. 4b, pg. 3).

4. Make sure that all nuts are tightened.

5. Attach the hinge bracket on each end of Z Bracket, then attache the Z Bracket to the adjustable slide using bolts and lock nuts

(included) (Fig. 5, 5a, pg. 3).

6. Attach the hinge bracket on the shorter side of Z Bracket to the rear of the rack enclosure using bolts (included).

Fig. 5

Fig. 5a

Fig. 4b

Fig. 3

Fig. 4a

Fig. 4

Fig. 3b

- 4 - T2RM7F8S(D)Q Installation Guide

T2RM7F8S(D)Q: Configuration of Mercury Boards:

1. Fasten spacers onto metal pems configuration

(A), (B) or (C) of backplane depending on the

access controller (Fig. 6, pg. 4).

2. Position access controller module over corresponding

spacers and fasten screws into spacers (Fig. 6a, pg. 4).

3. Mount backplane to enclosure with hardware.

Mercury Access Controller

Position Chart for the

Following Models:

Altronix/Mercury Pem Mounting

LP1502, LP4502, MR52,

MR16IN, MR16OUT A

LP2500, MUX8 B

Genetec Cloudlink C

Altronix

eFlow104NB

– DC +– BAT +

L G N

Altronix VR6

is mounted

under

LINQ8ACM(CB)

+ INP1 --

PWR1 +OFF

IN1

IN2

PWR1 +

PWR2 +

COM (--- )

+ INP2 --

IN1 Fuse

Common Power Outputs (NEG)

OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

1 2 3 4 5 6 7 8

Altronix PDS8(CB)

COM -

+PWR2 +PWR1

+ PWR1 - + PWR2 -

COM -

F- R- GND GND C

F+ R+ EOL RST NC FACP + PS1 - + BAT - + PS2 - + BAT -

NO C NC COM NO C NC COM NO C NC COM NO C NC COM NO C NC COM NO C NC COM NO C NC COM NO C NC COM

+PWR2

+PWR1

NC C NO

BAT AC

Tamper

NC C NO

+ INP1 -+INP2 -+INP3 -+INP4 -

+ INP5 -+INP6 -+INP7 -+INP8 -

Altronix LINQ8ACM(CB)

To IEC connector

To LED lense

Pem

Spacer

Backplane

Pan Head Screw

Mercury Board

Fig. 6a

Altronix

eFlow104NB

Fig. 6

T2RM7F8S(D)Q Installation Guide - 5 -

Notes:

- 6 - T2RM7F8S(D)Q Installation Guide

Notes:

T2RM7F8S(D)Q Installation Guide - 7 -

Notes:

- 8 - T2RM7F8S(D)Q Installation Guide

Trove2R Enclosure Dimensions (H x W x D approximate):

3.375” x 19.0” x 33.25” (85.8mm x 482.6mm x 844.6mm). Shown with Z Bracket attached.

Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice.

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––