Altronix NetWaySP1BT Series User manual

DOC#: NetWaySP1BT Rev. 032620 More than just power.TM
NetWaySP1BT
- 802.3bt Media Converter/Injector
- Modular plastic case.
NetWaySP1BTWPN
- 802.3bt Media Converter/Injector.
- NEMA4/4X rated outdoor enclosure.
Installation Guide
NetWaySP1BT Series
802.3bt Media Converter/Injectors
Models Include:

- 2 - NetWaySP1BT Series
Table of Contents:
Overview .................................................................pg. 3
Features .................................................................pg. 3
Recommended Altronix Power Sourcing Equipment ...............................pg. 3
Recommended Altronix SFP Modules ...........................................pg. 3
Installation Instructions......................................................pg. 4
Typical Application .........................................................pg. 5
Technical Specifications .....................................................pg. 6
Wall Mount Installation ......................................................pg. 7
Mechanical Drawing and Dimensions...........................................pg. 8

NetWaySP1BT Series - 3 -
Overview:
Altronix NetWaySP1BT and NetWaySP1BTWPN 802.3bt media converter/injectors provide a single 802.3bt
(4PPoE) port up to 90W and accommodate Fiber (1000Base-X/SX/LX) or structured cable to transmit data. Units
can be deployed with structured cable, conventional single/multimode fiber or composite cable (fiber + copper
combined). Cameras/edge devices may be located up to 100m from the unit.
Features:
Agency Listings:
• CE European Conformity.
Input:
• 48-56VDC @ 1.9A (95W).
* See below for recommended
Power Sourcing Equipment.
Fiber Port:
• One (1) 1Gb SFP port.
** See below for recommended SFP modules.
PoE Port:
• Single port rated up to 90W max.
• IEEE 802.3af, 802.3at and 802.3bt compliant.
Data Port:
• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair CAT5e and higher.
• Speed: 10/100/1000 Mbps.
• Distance: up to 100m.
Environmental:
• Refer to Environmental Conditions on page 5.
LED Indicators (Refer to Fig. 4, Pg. 4):
• Yellow and Green LEDs (RJ45 jacks):
Yellow (left) LED: 10/100 Mbps.
Green (right) LED: 1000 Mbps.
• Green PoE LEDs: Indicate PoE present.
• Green SFP (Fiber) LED: Indicates SFP connection.
Mechanical:
NetWaySP1BT:
• Modular plastic case.
3.375” x 3.8” x 1” (85.7mm x 96.5mm x 25.4mm).
NetWaySP1BTWPN:
• NEMA4/4X, IP66 Rated enclosure for outdoor use.
• Dimensions (H x W x D approx.):
9.5” x 7.32” x 4.92”
(241.3mm x 185.9mm x 125mm)
Recommended Altronix Power Sourcing Equipment:
NetWaySP4P Ethernet to Fiber Media Converter with Integral Power Supply/Charger.
Four (4) 56VDC non power-limited outputs up to 120W max. full power per port
(240W total power). Four (4) 1Gb SFP ports.
NetWaySP4PX Ethernet to Fiber Media Converter with Integral Power Supply/Charger.
Four (4) 56VDC non power-limited outputs up to 120W max. full power per port
(480W total power). Four (4) 1Gb SFP ports.
NetWaySP4P2 Ethernet to Fiber Media Converter with Integral Power-Limited Power Supply/Charger.
Four (4) 56VDC power-limited outputs up to 60W max. full power per port
(240W total power). Four (4) 1Gb SFP ports.
WayPoint562 High Current Outdoor Power Supply/Charger.
56VDC/120W output.
Filtered and electronically regulated output. Short circuit and thermal overload protection.
Vertiline563 EIA 19” 1U Rack Mountable Dual Independent Power Supply/Charger.
56VDC @ 3A each output.
Filtered and electronically regulated output. Short circuit and thermal overload protection.
PoE201 Power Supply/Charger Board.
56VDC/120W output.
Filtered and electronically regulated output. Short circuit and thermal overload protection.
Recommended Altronix SFP Modules:
Altronix P1MM, P1SM10, P1AB2K and P1GCE are hot-pluggable SFP fiber transceiver modules and are readily
usable with all Altronix Spectrum fiber optic equipment for 1Gb transmission rates.
P1MM For use with Multi-Mode Fiber for distances up to 550m.
P1SM10 For use with Single-Mode Fiber for distances up to 10km.
P1AB2K For use with Single Strand Single-Mode Fiber for distances up to 2km.
P1GCE For use with CAT5e or better for distances up to 100m.

- 4 - NetWaySP1BT Series
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes
and authorities having jurisdiction. All units should be installed by a trained service personnel.
Installation:
NetWaySP1BT:
1. Mount NetWaySP1BT in desired location utilizing the mounting hole (Fig. 1a, pg. 4). Use a proper fastener
and/or wall anchor when securing NetWaySP1BT with screw through its mounting hole to the surface.
Note: Earth ground can be used, if needed, for high transient or outdoor environments.
If used, insert an Earth ground wire (included with product) into the internal ground terminal until
secured (a slight tug can check stability) & fasten the free end to a chassis earth ground.
If earth ground is not attached and needed, refer to Fig. 3, pg. 5 for manual placement.
NetWaySP1BTWPN:
2. Remove backplane from enclosure prior to drilling. Do not discard hardware.
Note: Make sure that hardware will not interfere with components of the circuit board.
3. Mark and drill desired inlets on the enclosure to facilitate wiring. Maximum NEMA type 4X rated fittings
to be used are 0.5”. Follow manufacturer’s specifications for the appropriate size opening.
Note: Inlets for conduit fittings should only be made on the bottom of the enclosure.
To facilitate wire entry utilize weather-tight NEMA rated connectors (supplied), bushings, and cable.
4. Clean out the inside of enclosure before remounting circuit boards/backplane.
5. Mounting NEMA4/4X rated enclosure (Enclosure Dimensions, pg. 7):
Wall mount: Mount unit in desired location. Mark and drill holes to line up with the top and bottom
hole of the enclosure flange. Secure enclosure with appropriate fasteners (e. g. screws
and anchors; bolts and locking nuts, etc.) that are compatible with mounting surface and
are of sufficient length/construction to ensure a secure mount (Fig. 5, pg. 7).
Pole Mount: Refer to Fig. 6 - 10, pg. 7.
6. Mount backplane in enclosure with hardware.
Power Connection:
1. Use external 48-55V UL Listed ITE power supply, carefully observing correct polarity (Fig. 1, 2, pg. 4).
2. Use 14AWG or larger for all power connections.
Keep power-limited wiring separate from non power-limited wiring by utilizing separate knockouts/
inlets. Minimum 0.25” spacing must be provided.
CAUTION: Do not touch exposed metal parts. Shut branch circuit power before installing or servicing
equipment. There are no user serviceable parts inside. Refer installation and servicing to qualified
service personnel.
NetWaySP1BT
802.3bt Converter/Injector
Input: 48–56VDC
Output: IEEE 802.3bt (90W)
48-56VDC
-- Input +
48-56VDC
-- Input +
Ground
802.3bt
Output Data
Port
Fiber
Signal
PoE
SignalSFP
NetWaySP1BT
802.3bt Converter/Injector
Input: 48–56VDC
Output: IEEE 802.3bt (90W)
48-56VDC
-- Input + 802.3bt Output Data
Port
Fiber
Signal
PoE
Signal SFP
48-56VDC
-- Input +
Optional
Earth
Ground
Fig. 1 NetWaySP1BT Fig. 2 NetWaySP1BTWPN
Fig. 1a

NetWaySP1BT Series - 5 -
Input/Data Connections:
1. Connect structured cable from port marked [Data Port] on NetWaySP1BT to a PoE midspan/endspan
(Fig. 3, pg. 5).
2. Connect fiber optic cable to a fiber SFP module. Connect the module to the port marked [SFP] on the
NetWaySP1BT. Connect the other end of fiber cable to an SFP module of a remote device.
SFP LED will illuminate indicating data connection (Fig. 3, pg. 5).
3. Using 4-pair CAT5e or higher cable connect PoE load device to be powered to the port marked
[802.3bt Output] on NetWaySP1BT. After authentication and classification have been established,
[PoE Signal] LED will illuminate indicating PoE presence.
Ethernet Data Port
Yellow LED
10/100 Mbps
Green LED 1000 Mbps
IEEE 802.3af, 802.3at and 802.3bt
compliant port rated up to 90W max
48VDC to 56VDC
Input
-- +
SFP LED Indicates
data connection
PoE LED indicates PoE present
One (1) Gb SFP port
for Fiber
48-56VDC
– Input +
802.3bt
Output
Data
Port
Fiber
Signal
PoE
Signal SFP
Ground Terminal
Fig. 3
NetWaySP1BT
Converts Ethernet or Fiber to
802.3bt PoE port
Fiber
OR
CAT5e/6 CAT5e/6
PoE+ (90W) PTZ Data from Midspan/Endspan
From power supply
NetWaySP1BT
802.3bt Converter/Injector
Input: 48–56VDC
Output: IEEE 802.3bt (90W)
48-56VDC
-- Input + 802.3bt Output Data Port Fiber Signal
PoE
Signal SFP
Typical Application:
Fig. 4

- 6 - NetWaySP1BT Series
Technical Specifications:
Parameter Description
Ports One (1) 1Gb SFP port, one (1) Data port.
One (1) IEEE 802.3af, 802.3at and 802.3bt compliant output port rated up to 90W max.
Input Power
Requirements
48-56VDC @ 1.9A (95W).
See pg. 3 for recommended Power Sourcing Equipment.
Indicators
Yellow and Green LEDs (RJ45 jacks): IP Link status, 10/100/1000 Base-T/active.
PoE Green LED: Indicates PoE present.
Fiber Signal Green LED: Indicates SFP connection.
Evironmental
Conditions
Temperature:
NetWaySP1BT:
Operating (90W): – 40ºC to 75ºC (– 40ºF to 167ºF).
Storage: – 40ºC to 75ºC (– 40ºF to 167ºF).
NetWaySP1BTWPN:
Operating:
60W: – 40ºC to 75ºC (– 40ºF to 167ºF).
80W: – 40ºC to 70ºC (– 40ºF to 158ºF).
90W: – 40ºC to 60ºC (– 40ºF to 140ºF).
Storage: – 40ºC to 85ºC (– 40ºF to 185ºF).
Relative Humidity: 85% +/–5%.
Operating Altitude: – 304.8 to 2,000m.
Regulatory
Compliance CE European Conformity.
Weights (approx.) NetWaySP1BT: Product: 0.25 lb. (0.11 kg) | Shipping: 0.3 lb. (0.14 kg).
NetWaySP1BTWPN: Product: 3.7 lb. (1.68 kg) | Shipping: 5 lb. (2.27 kg).

NetWaySP1BT Series - 7 -
Wall Mount Installation:
1- Place unit at desired location and secure with mounting
screws (not included) (Fig. 5, pg. 7).
Fig. 5
Pole Mounting Using Optional Pole Mount Kit PMK1:
This installation should be made by qualified service personnel. This product contains no serviceable parts. PMK1
outdoor pole mount kits is designed to simplify the installation of Altronix outdoor rated power supplies and acces-
sories housed in models WP1, WP3 and WP4 NEMA rated enclosures. PMK1 can be mounted on 2” to 8” (50.8mm
to 203.2mm) diameter round or 5” (127mm) square poles. Brackets are designed for use with the Wormgear Quick
Release Straps (two included).
1. Thread one (1) wormgear quick release strap through the slots on the back of a mounting bracket (Fig. 6, pg. 7).
2. Once the desired height of the top Pole Mount bracket is achieved, tighten the straps down by sliding open
end of the strap through the locking mechanism on the strap, then tighten the screw with
flat head screwdriver or 5/16” hex socket driver (Fig. 7, pg. 7 and Fig. 9, pg. 7).
3. Attach the bottom bracket to the enclosure by inserting bolts through the flange of the enclosure and into the
bracket, tightening bolts with a 7/16” hex socket (Fig. 8, pg. 7).
4. Thread the second wormgear quick release strap through the slots on the back of the bottom mounting
bracket (Fig. 9, pg. 7).
5. Mount enclosure onto the top bracket by inserting bolts through flange of the enclosure and into the bracket,
tightening bolts with a 7/16” hex socket (Fig. 8, pg. 7).
6. Tighten the straps of the bottom bracket down by sliding the open end of the strap through the locking
mechanism on the strap, then tighten screw with flat head screwdriver or 5/16” hex socket driver
(Fig. 7, 9, pg. 7).
7. Clip excess straps.
Fig. 6 Fig. 7 Fig. 8
Fig. 9
Fig. 10
2” to 8”(50.8mm to 203.2mm)
diameter round pole
Fig. 10a
5” (127mm) square pole

- 8 - NetWaySP1BT Series
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty | Made in U.S.A.
IINetWaySP1BT Series F17U MEMBER
NetWaySP1BTWPN
Mechanical Drawing and Dimensions (H x W x D approx.):
9.5” x 7.32” x 4.92” (241.3mm x 185.9mm x 125mm)
4.25” (108mm)
6.0” (152.4mm)
6.75” (171.5mm)
6.27” (159.3mm)
8.75” (222.2mm)
8.0” (203.2mm)
9.5” (241.3mm)
10-32 X 0.25” (6.4mm)
4 Places
4.35” (110.5mm)
8.75” (222.2mm)
1.38”
(35.1mm) 3.54” (89.9mm)
7.32” (185.9mm)
9.32” (236.7mm)
304 Stainless Steel Piano Hinge
4.92” (125mm)
4.0” (101.6mm)
0.312” (7.9mm) TYP
4 Places
316 Stainless Steel
Padlock Latch Attached
0.375” (9.5mm)
Padlock Eye