Altronix R2416UL User manual

Rack Mount Series
UL Listed CCTV Power Supplies
Installation Guide
Models Include:
•R2416UL •R2416ULCB
- 24VAC @ 7 amp (170VA) - 24VAC @ 7 amp (170VA)
or 28VAC @ 6 amp (170VA). or 28VAC @ 6 amp (170VA).
- Sixteen (16) Fuse Protected Outputs. - Sixteen (16) PTC Protected Outputs.
•R2416300UL •R2416300ULCB
- 24VAC @ 12.5 amp (300VA) - 24VAC @ 12.5 amp (300VA)
or 28VAC @ 10 amp (280VA). or 28VAC @ 10 amp (280VA).
- Sixteen (16) Fuse Protected Outputs. - Sixteen (16) PTC Protected Outputs.
•R2416600UL •R2416600ULCB
- 24VAC @ 25 amp (600VA) - 24VAC @ 25 amp (600VA)
or 28VAC @ 20 amp (560VA). or 28VAC @ 20 amp (560VA).
- Sixteen (16) Fuse Protected Outputs. - Sixteen (16) PTC Protected Outputs.
Rev. 040506
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

      
        
   
     
    

    
     
  
        
         
Overview:
These Altronix Rack Mount CCTV Power Supplies provide 24VAC or 28VAC distributed via sixteen (16) fuse or
PTC protected outputs for powering CCTV Cameras, heaters and other video accessories.
Sixteen (16) Output Rack Mount Configuration Reference Chart:
Altronix
Model Number Output Voltage (VAC) Total Output Current (Power) Number of Outputs PTC Protected Outputs (Class 2 power limited for Dry locations). (Class 3 for Wet locations). Fuse Protected Class 1 Outputs Individual Output Current (max per output not to exceed total output current) Fuse Ratings Primary In-line Fuse Ratings 115VAC 50/60Hz Input Current Agency Listings
R2416UL 24VAC 7 amp 16 Yes 3.5 amp 3.5
amp
3.5 amp/
250V 2.9 amp
28VAC 6 amp
R2416ULCB 24VAC 7 amp 16 Yes 2.5 amp 3.5 amp/
250V 2.9 amp
28VAC 6 amp
R2416300UL 24VAC 12.5 amp 16 Yes 3.5 amp 3.5
amp 3 amp
28VAC 10 amp
R2416300ULCB 24VAC 12.5 amp 16 Yes 2.5 amp 3 amp
28VAC 10 amp
R2416600UL* 24VAC 25 amp 16 Yes 3.5 amp 3.5
amp 6 amp
28VAC 20 amp
R2416600ULCB 24VAC 25 amp 16 Yes 2.5 amp 6 amp
28VAC 20 amp
*24VAC models: Outputs 1-8 provide 12.5 amp (300VA) max. Outputs 9-16 provide 12.5 amp (300VA) max.
*28VAC models: Outputs 1-8 provide 10 amp (280VA) max. Outputs 9-16 provide 10 amp (280VA) max.
Specifications:
•UL Listed for Commercial CCTV Equipment (UL 2044). •Sixteen (16) individual power LED indicators.
CUL Listed - CSA Standard C22.2 No. 1-98, Audio, •Removable terminal blocks with locking screw flange.
Video and Similar Equipment. •Unit maintains camera synchronization.
•24VAC or 28VAC (Factory set @24VAC). •Ease of installation saves time and eliminates costly labor.
•Illuminated power disconnect circuit breaker •2U rack mount chassis for use in standard EIA 19” rack.
with manual reset Rack Dimensions:
•Surge suppression. 3.25”H x 19.125”W x 8.5”D
Installation Instructions:
1. Mount unit in desired rack location (Space unit at least 3” from any video monitors), Do not obstruct side air vents.
2. Set power disconnect circuit breaker to OFF position (Fig. 1d, pg. 3).
3. The unit is factory set for 24VAC operation.
For 28VAC operation, adjust unit prior to mounting and applying power as follows:
a. Open bottom of unit by removing six (6) screws (Rack Mechanical Drawing & Dimensions, pg. 4).
b. For 28VAC operation, adjust unit prior to mounting and applying power as follows:
Change the wire position so that the black wire [28V] is connected to the terminal marked [P] and
the yellow wire [24V] is connected to the terminal marked [S].
c. After securing all wires for proper voltage place bottom panel back on the unit and fasten with the six (6) screws.
Note: R2416ULCB set for 28VAC operation is not Class 2 Rated, not power limited.
4. Plug power cord into grounded 115VAC 50/60 Hz receptacle (Fig. 1c, pg. 3), ground should be connected
as indicated in (Fig. 1e, pg. 3).
- 2 - R2416ULseries
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

        
            
              
               
             
              
              
     
        
                
             
  
   
Fig. 1 Fig. 1a Fig. 1b Fig. 1c Fig. 1d
set for 28VAC.
XFMR*
ALTRONIX CORP.
BROOKLYN, NY 11220
MADE IN USA
XFMR*
N P S
AC Power
LED's AC Power
LED's AC Power
LED's AC Power
LED's
Divider
Removable Terminal
Block
(Green Wire
Earth GND)
Fuse Fuse
SPNSPN
24VAC Output
(Factory Set)
28VAC (Black) 24VAC (Yellow) COM (Brown) 28VAC (Black) 24VAC (Yellow) COM (Brown)
28VAC Output
Illuminated
Power Disconnect
Circuit Breaker with
manual reset
P N
S
Strain Relief
Line Cord
Fig. 1e
Class 2 Rated Power Limited Outputs.
Except for R2416UL, R2416300UL,
R2416600UL and R2416ULCB when
PTC1
Used
on PTC
Models
5. Set power disconnect circuit breaker to RESET (ON) position (Fig. 1d, pg. 3).
6. Measure output voltage before connecting devices. This helps avoid potential damage.
All terminals with common suffix (P) “1P, 2P...” are the same polarity.
7. Set power disconnect circuit breaker to OFF position (Fig. 1d, pg. 3).
8. Connect devices to removable terminal blocks marked [1P & 1N through 16P & 16N] (Fig. 1a, pg. 3).
When wiring is completed on terminal blocks they can be locked down by tightening screw flanges.
9. Upon completion of wiring, set power disconnect circuit breaker to RESET (ON) position (Fig. 1d, pg. 3).
10. Green power LEDs on faceplate will illuminate when power is present. When an output is in
atrouble condition (blown fuse or tripped PTC) the corresponding LED will not be illuminated (Fig. 1, pg. 3).
a. Blown fuse (R2416UL, R2416300UL &R2416600UL) - Set power disconnect circuit breaker on back
of unit to the OFF position (Fig. 1e, pg. 3).
Remove front faceplate to access fuses. Replace with fuses rated @3.5A/250VA (Altronix model #Fuse1).
b. Tripped PTC (R2416ULCB, R2416300ULCB &R2416600ULCB) -Toreset PTC, set power switch on back
of unit to the OFF position. After approximately 30 secs. set power disconnect circuit breaker to
the ON (RESET) position (Fig. 1d, pg. 3).
11. Illuminated power disconnect circuit breaker with manual reset:
OFF position - Switch not Illuminated. Outputs not powered.
RESET (ON) position - Circuit breaker illuminated. Outputs powered.
Circuit breaker tripped - Circuit breaker is not Illuminated. Power LEDs on faceplate are not illuminated.
Outputs not powered.
To reset circuit breaker set power disconnect circuit breaker to RESET (ON) position (Fig. 1d, pg. 3).
R2416ULseries - 3 -
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

         
        
                
                 
             
                 
         
Note: Do not exceed units electrical load ratings as indicated in reference chart (pg. 2).
Do not place mechanical load on unit. Unit is designed optimally for normal data room office installations.
Data racks should always be properly ventilated.
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or
moisture. This installation should be made by qualified service personnel and should conform to
all local codes and in accordance with the National Electrical Code.
3.5A 250V
For fuse protected models:
Replace fuses with the same type and rating 3.5A/250V.
The lightning flash with arrow head symbol within an equilateral triangle is intended to alert the user to the
presence of an insulated “DANGEROUS VOLTAGE” within the products enclosure that may be of sufficient
magnitude to constitute an electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
CAUTION: To reduce the risk of electric shock do not open enclosure. There are
no user serviceable parts inside. Refer servicing to qualified service personnel.
Rack Mechanical Drawing & Dimensions
3.25”H x 19.125”W x 8.5”D
3.125"
8.5"
19.125"
17.625"
View from back
BOTTOM
View from front
BACK
FACEPLATE
.75"
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: [phone]
web site: www.altronix.com, e-mail: [email protected], Lifetime Warranty, Made in U.S.A.
IIR2416ULSeries H20K MEMBER
- 4 - R2416ULseries
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]