Altronix WayPoint17AU User manual

AC Outdoor Power Supplies
Installation Guide
Models Include:
WayPoint17AU WayPoint17ADU
- 24VAC @ 7.25A and/or 28VAC @ 6.25A. - 24VAC @ 7.25A and/or 28VAC @ 6.25A.
- Two (2) fuse protected outputs. - Two (2) PTC protected outputs.
WayPoint17A4U WayPoint17A4DU
- 24VAC @ 7.25A or 28VAC @ 6.25A. - 24VAC @ 7.25A or 28VAC @ 6.25A.
- Four (4) fuse protected outputs. - Four (4) PTC protected outputs.
WayPoint17A8U WayPoint17A8DU
- 24VAC @ 7.25A or 28VAC @ 6.25A. - 24VAC @ 7.25A or 28VAC @ 6.25A.
- Eight (8) fuse protected outputs. - Eight (8) PTC protected outputs.
Rev. 091514-17A More than just power.™

- 2 - WayPoint17A
Overview:
WayPoint Outdoor Power Supplies provide 24VAC and/or 28VAC distributed via two (2), four (4) or eight (8) outputs
for powering CCTV cameras, heaters, and other video accessories.
WayPoint AC Reference Chart:
Altronix
Model Number Output Voltage
Total
Output
Current
(Power)
Number
and Type
of Outputs
Fuse
Output
Ratings
PTC
Output
Ratings
Input Current Draw
Product
Weight
115VAC
60Hz
230VAC
50Hz
WayPoint17AU
24VAC 7.25A 25A/32V* -----
2.0A 1A
5.95kg28VAC 6.25A
24VAC and 28VAC 6.25A 1 of each
WayPoint17ADU
24VAC 7.25A 2----- 2.5A 5.95kg28VAC 6.25A
24VAC and 28VAC 6.25A 1 of each
WayPoint17A4U 24VAC 7.25A 4 Fused 5A/32V* ----- 5.95kg
28VAC 6.25A
WayPoint17A4DU 24VAC 7.25A 4 PTCs ----- 2.5A 5.95kg
28VAC 6.25A
WayPoint17A8U 24VAC 7.25A 8 Fused 5A/32V* ----- 6.1kg
28VAC 6.25A
WayPoint17A8DU 24VAC 7.25A 8 PTCs ----- 2.5A 6.1kg
28VAC 6.25A
*Lower rated fuses can be used.
Specifications:
Installation Instructions:
Unit should be installed in accordance with The National Electrical Code and all applicable Local Regulations.
1. Remove back plane from enclosure prior to mounting (do not discard hardware).
2. Mark and drill desired inlets on the enclosure to facilitate wiring (Fig. 1, pg. 4).
Note: Inlets for conduit fittings should only be made on the bottom of the enclosure.
UL Listed NEMA type 4X rated conduit connector/hubs shall be used for the appropriate size inlets.
3. Mount unit in desired location. Mark and drill holes to line up with the top and bottom holes of the enclosure flange.
Secure enclosure with appropriate fasteners (Fig. 5, pg. 7 and Fig. 10, pg. 8).
4. Mount back plane to enclosure with hardware.
5. Set the input voltage selector switch for 115VAC or 230VAC operation (Figs. 2-4, pgs. 4-6)
6. To facilitate wire entry utilize weather-tight NEMA 4 rated connectors, bushings, and cable.
7. Set illuminated master power disconnect circuit breaker to the [OFF] position (Figs. 2-4, pgs. 4-6).
8. Connect unswitched AC power (115VAC/230VAC, 50/60 Hz) to terminals marked [L, N] (Figs. 2-4, pgs. 4-6).
Green branch wire connects to earth (safety) ground lug .
Wire gauge range of connectors is 14 AWG to 11 AWG (1.6 mm to 2.5 mm diameter).
9. Set illuminated master power disconnect circuit breaker to the [RESET/ON] position (Figs. 2-4, pgs. 4-6).
10. WayPoint17A4U/A4DU, WayPoint17A8U/A8DU are factory set for 24VAC operation.
For 28VAC operation, adjust unit prior to mounting and applying power as follows:
Change the wire position so that the black wire [28V] is connected to the terminal marked [P] and
the yellow wire [24V] is connected to the terminal marked [S].
Agency Listings:
• UL/cUL Listed for Information Technology Equipment
(UL 60950-1) and Equipment to be Installed Outdoors
(UL 60950-22).
• CE European Conformity.
Input:
• Input: 115VAC, 60Hz, 2A or 230VAC, 50Hz, 1A.
Output:
• Output options:
a. 24VAC or 28VAC.
b. Both 24VAC and 28VAC (WayPoint17AU/ADU only).
Visual Indicators:
• Individual power output LED indicators.
Visual Indicators (cont’d):
• Illuminated master power switch.
Features:
• Surge suppression.
• Spare fuses included.
Accessories:
• Optional PMK1 Pole Mount Kit simplifies installation of
outdoor units.
Enclosure:
• NEMA 4/4X, IP66-11 Rated enclosure for outdoor use.
• Enclosure Dimensions (H x W x D approx.):
13.31” x 11.31” x 5.59”
(338.074 mm x 287.274 mm x 141.986 mm).

WayPoint17A - 3 -
11. Measure output voltage on terminals marked [COM, 24V, 28V] on WayPoint17AU and WayPoint17ADU
(Fig. 2, pg. 4) or [1-4 or 1-8 COM] on WayPoint17A4U, WayPoint17A4DU, WayPoint17A8U and
WayPoint17A8DU before connecting devices (Fig. 3, pg. 5, Fig. 4, pg. 6). This helps avoiding potential damage.
12. Set illuminated master power disconnect circuit breaker to the [OFF] position (Figs. 2-4, pgs. 4-6).
13. Connecting devices to WayPoint17AU or WayPoint17ADU:
For 24VAC output connect devices to terminals marked [COM, 24V] (Fig. 2, pg. 4).
For 28VAC output connect devices to terminals marked [COM, 28V] (Fig. 2, pg. 4).
Connecting devices to WayPoint17A4U or WayPoint17A4DU:
Connect device to terminals marked [1-4] and [COM] (Fig. 3, pg. 5).
Connecting devices to WayPoint17A8U or WayPoint17A8DU:
Connect device to terminals marked [1-8] and [COM] (Fig. 4, pg. 6).
14. Set illuminated master power disconnect circuit breaker to the [RESET/ON] position (Figs. 2-4, pgs. 4-6).
15. LEDs will illuminate indicating each output is powered (Figs. 2-4, pgs. 4-6).
16. Upon completion of wiring secure enclosure door with latches and optional lock.
Caution: Equipment to be installed / serviced by authorized / trained personnel only.
Shut branch circuit power before installing / servicing equipment.
WARNING: When installing in a non-restricted service area use lock or other fastened means on door
latches. This installation should be made by qualified service personnel and should conform to the National
Electrical Code and all local codes.
LED Identification Chart:
ON OFF
Normal operating condition. No AC output. Blown fuse or tripped PTC, illuminated master power
disconnect circuit breaker is tripped or OFF, AC failure.
Technical Specifications:
Parameter Description
Input power
requirements Input: 115VAC, 60Hz, 2A or 230VAC, 50Hz, 1A.
Indicators Individual power output LED indicators.
Illuminated master power switch.
Environmental
Conditions
Operating Ambient Temperature:
140ºF (60°C) for 24VAC @ 7.25A (174VA) output
or 158ºF (70°C) for 28VAC @ 6.25A (175VA) output.
Relative Humidity: 85%, +/--- 5%
Storage Temperature: --- 40ºF to 167ºF (-40ºC to 75ºC).
Operating Altitude: --- 1000 to 6,561.679 ft. (--- 304.8 to 2000m).
Regulatory
Compliance
UL/cUL Listed for Information Technology Equipment (UL 60950-1) and
Equipment to be Installed Outdoors (UL 60950-22).
CE European Conformity.
For fuse protected models:
Replace fuses with the same type and rating 5A/32V.
The lightning flash with arrow head symbol within an equilateral triangle is intended to alert the user to the
presence of an insulated DANGEROUS VOLTAGE within the product’s enclosure that may be of sufficient
magnitude to constitute an electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
CAUTION: To reduce the risk of electric shock do not open enclosure. There are
no user serviceable parts inside. Refer servicing to qualified service personnel.
5A 32V

- 4 - WayPoint17A
Fig. 2 - WayPoint17AU/WayPoint17ADU
CAUTION
HIGH VOLTAGE
COM 24V 28V COM 24V 28V
COM 24V 28V COM 24V 28V
28V 24V COM
PD2WP
PD2WP
Input Voltage
Power Input
115V
115 230
LG N
5
5
5
5
28V 24V COM
Input Voltage
Power Input
115V
115 230
LG N
Used on WayPoint17ADU
Ground
Lug
ALTRONIX CORP.
www.altronix.com
BROOKLYN,NY 11220
ALTRONIX CORP.
www.altronix.com
BROOKLYN,NY 11220
Bottom of Enclosure
Suggested Locations
for Wiring Inlets
Fig. 1

WayPoint17A - 5 -
Fig. 3 - WayPoint17A4U/WayPoint17A4DU
CAUTION
HIGH VOLTAGE
1 COM 2 COM
PD4WP
PD4WP
3 COM 4 COM
Input Voltage
Power Input
115V
115 230
LGN
S P N
5
5
5
5
1 COM 2 COM 3 COM 4 COM
Input Voltage
Power Input
115V
115 230
LGN
S P N
Used on WayPoint17A4DU
Ground
Lug
ALTRONIX CORP.
www.altronix.com
BROOKLYN, NY 11220
ALTRONIX CORP.
www.altronix.com
BROOKLYN, NY 11220

- 6 - WayPoint17A
CAUTION
HIGH VOLTAGE
1 2 3 4 5 6 7 8
Common
PD8WP
PD8WP
Input Voltage
Power Input
115V
115
230
LG N
S P N
1 2 3 4 5 6 7 8
5 5
5
5 5 5
5
5
1 2 3 4 5 6 7 8
Common
Input Voltage
Power Input
ALTRONIX CORP.
www.altronix.com
MADE IN USA
BROOKLYN,NY 11220
115V
115
230
LG N
S P N
1 2 3 4 5 6 7 8
Used on WayPoint17A8DU
Ground
Lug
ALTRONIX CORP.
www.altronix.com
BROOKLYN, NY 11220
ALTRONIX CORP.
www.altronix.com
BROOKLYN, NY 11220
Fig. 4 - WayPoint17A8U/WayPoint17A8DU

WayPoint17A - 7 -
Wall Mount Installation
1- Place unit at desired location and secure with mounting
screws (not included) (Fig. 5, pg. 7).
Fig. 5
Pole Mounting Using Optional Pole Mount Kit PMK1 (not included):
This installation should be made by qualified service personnel. This product contains no serviceable parts. PMK1 is in-
tended for use with Altronix outdoor rated power supplies or accessories housed in WP1, WP2, WP3 and WP4 enclosures.
Brackets are designed for use with the Wormgear Quick Release Straps (two included).
1. Thread one (1) wormgear quick release strap through the slots on the back of a mounting bracket (Fig. 6, pg. 7).
2. Once the desired height of the top Pole Mount bracket is achieved, tighten the straps down by sliding open end
of the strap through the locking mechanism on the strap, then tighten the screw with
flat head screwdriver or 5/16” hex socket driver (Fig. 6, pg. 7 and Fig. 7, pg. 7).
3. Attach the bottom bracket to the enclosure by inserting bolts through the
flange of the enclosure and into the bracket, tightening bolts with a
7/16” hex socket (Fig. 8, pg. 7).
4. Thread the second wormgear quick release strap through the slots on the
back of the bottom mounting bracket (Fig. 6, pg. 7).
5. Mount enclosure onto the top bracket by inserting bolts through
flange of the enclosure and into the bracket,
tightening bolts with a 7/16” hex socket (Fig. 7, pg. 7).
6. Tighten the straps of the bottom bracket down by sliding the open end of
the strap through the locking mechanism on the strap, then tighten screw
with flat head screwdriver or 5/16” hex socket driver (Fig. 9/9a, pg. 7).
7. Clip excess straps.
Fig. 9 - 2” to 8”(50.8mm to 203.2mm) Fig. 9a - 5” (127mm) square pole
diameter round pole
Fig. 6 Fig. 7 Fig. 8
Fig. 7

- 8 - WayPoint17A
Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: [phone]
website: www.altronix.com, e-mail: [email protected]. Lifetime Warranty, Made in U.S.A.
IIWayPoint17A C06Q MEMBER
1.61”
(40.894mm)
3.96”
(100.584mm)
5.60”
(142.24mm)
10-32 X 0.375” (9.525mm) BRASS INSERT (X4)
STAINLESS STEEL PIANO HINGE
11.32” (287.528mm)
13.32”
(338.328mm)
PADLOCK LATCH AT TACHED
WITH RIVETS (Ø 0.375” (9.52mm) PADLOCK EYE).
10.75” (273.05mm)
10.00” (254mm)
8.25” (209.55mm)
10.25”
(260.35mm)
12.00”
(304.8mm)
13.50”
(342.9mm)
10-32 X 0.25” (6.35mm) BRASS INSERT (X2)
Ø 0.32 (8.128mm) MOUNTING HOLE TYP. 4 PLACES
12.75”
(323.85mm)
8.00” (203.2mm)
Enclosure Dimensions (H x W x D):
13.31” x 11.31” x 5.59” (338.074 mm x 287.274 mm x 141.986 mm)
Fig. 10