Altronix Pace1PRD User manual

Overview:
Pace1PRD is a long range Ethernet receiver which transmits data at 100Mbps full duplex and power via a CAT5e
or higher cable. The Pace1PRD receiver is powered via Altronix NetWay1D midspan injector. The receiver passes
the Hi-PoE (60W) power over the cable to the eBridge200WPM transceiver which, in turn, passes this power to
an enabled IP camera/device. These plug and play units facilitate cost-effective solutions for IP devices that need
to be installed at distances greater than 100m.
Features:
Agency Listings:
• UL/cUL Listed for Information
Technology Equipment (UL 60950-1).
• CE European Conformity.
Input:
• Powered by NetWay1D (60W).
Ethernet:
• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair CAT5 structured cable.
• Distance: up to 500m.
• Speed: 10/100BaseT, half/full duplex,
auto negotiation.
• Throughput is rated to pass 100Mbps of
data at distances up to 500m.
With proper headend equipment this
supports Megapixel, HD720, HD1080.
CAT5e or Higher:
• Distance: up to 500m @ 100Mbps
(see Cable Type, Total Device Power,
Data and Power Distance, pg. 3).
LED Indicators:
• Green - PoE ON (by respective RJ45 jack).
• Yellow and Green LED IP Link status,
10/100Base-T/active.
Environmental:
• Operating Temperature:
– 20ºC to 49ºC (– 4ºF to 120.2ºF).
• Storage Temperature:
– 30ºC to 70ºC (– 22ºF to 158ºF).
• Humidity: 20 to 85%, non-condensing.
Functions:
• Auto detection and protection of legacy
non-PoE cameras/devices.
Applications:
• Extend Network link distance in an
industrial environment (see note, pg. 2).
• Works with Megapixel, HD720, HD1080
and VGA (SD) cameras (see note, pg. 2).
Mechanical:
• Dimensions (W x L x H approx.):
3.5” x 3.5” x 1”
(88.9mm x 88.9mm x 25.4mm).
I.T.E. 43KC
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes
and authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application.
Pace1PRD is intended for indoor use only.
1. Pace1PRD Installation:
a. Secure unit to desired mounting surface with a proper fastening device utilizing the unit’s mounting hole
(Fig. 2a, pg. 3). Unit should be mounted in proximity to ethernet switch/network, NVR or video server.
b. Connect structured cable from NetWay1D to RJ45 jack marked [PoE Input] (Fig. 2, pg. 3).
c. CAT5e or higher: Connect CAT5e or higher cable to connector marked [RJ45 Link] (Fig. 2, pg. 3).
2. eBridge200WPM Connections:
a. Connect CAT5e from Pace1PRD (60W) to connector marked [CAT INPUT] (Fig. 2, pg. 3)
b. Select input power SW3 on switch marked [60W CAT, 30W CAT or 60W COAX] (Fig. 2, pg. 3).
c. Connect structured cable from one (1) 60W camera/device to RJ45 jack marked [Port 1] or connect two (2)
individual structured cables from two (2) 30W cameras/devices to RJ45 jacks marked [Port 1] & [Port 2]
(Fig. 2, pg. 3).
Pace1PRD
IP and Hi-PoE Receiver
over extended distance
CAT5e
Installation Guide

- 2 - Pace1PRD Installation Guide
Technical Specifications:
Parameter Description
Connections RJ45 for ethernet link.
Input Power
Requirements
60W from Midspan or endspan port connected.
PoE compliant to IEEE 802.3af (15W) and
PoE+ compliant to IEEE 802.3at (30W), Hi-PoE (60W)
Indicators
Yellow (RJ45 connector): On - Link, Off - No Link, Blinking - Activity.
Green (RJ45 connector): On - 100Base-TX, Off - 10Base-T.
Green: PoE Active.
Environmental
Conditions
Operating Ambient Temperature (UL60950-1):
– 20ºC to 49ºC (– 4ºF to 120.2ºF).
Relative humidity: 20 to 85%, non-condensing.
Storage Temperature: – 30ºC to 70ºC (– 22ºF to 158ºF).
Operating Altitude: – 304.8 to 2,000m.
Regulatory
Compliance
UL/cUL Listed for Information Technology Equipment (UL 60950-1).
CE European Conformity.
Weights (approx.) Product: 3.88 oz. (0.11 kg.) | Shipping: 6.70 oz. (0.19 kg.)
Fig. 1 Pace1PRD
*Note: Caution: once Hi-PoE connection is established between Pace1PRD and eBridge200WPM, discon-
nection from eBridge200WPM will not disable the Hi-PoE output voltage on the Pace1PRD, although the
eBridge200WPM can be reconnected, caution should be taken not to connect the CAT5e wiring from Pace1PRD
to any non-PoE device.
Structured
Cable to
NetWay1D
Midspan
Injector
Green LED
indicates
Hi-PoE Present
from Midspan/
Endspan
Green LED
indicates
Hi-PoE being
transmitted to
eBridge200WPM
CAT5e or
higher from
eBridge200WPM

Pace1PRD Installation Guide - 3 -
Single PoE Camera Connection:
Fig. 2
1
PORT 1 PORT 2
CAT INPUT
COAX INPUT
SPEED ACTIVITY
SW3
SPEED
ACTIVITY
SPEED
ACTIVITY
SPR
PoE
DATA
PoE
SPR
PoE
DATA
PoE
60W CAT
30W CAT
or
60W COAX
SW3
60W CAT
30W CAT
or
60W COAX
CAT5e - 500m
CAT5e - 100m CAT5e - 100m
CAT5e - 100m
Option 1 Option 2
PoE+
Camera/
Device
PoE+
Camera/
Device
60W
Camera/Device
NetWay1D
Aux.
+ ---
INOUT
PoE
ON
Pace1PRD
RJ45
Link
Output
PoE
LED
Input
PoE
LED
PoE
Input
I.T.E. 43KC
Z1409
RJ45 LEDs Yellow - Activity
Green - Speed
Green LED Power and PoE
www.altronix.com
IP- Receiver
Passes Hi-PoE
Pace1PRD - Receiver

- 4 - Pace1PRD Installation Guide
Cable Type, Total Device Power, Data and Power Distance:
Cable Type Total Power
Consumption
Max. Data
Distance
Max. Power
Distance
CAT5e 15W 500m 500m
CAT5e 30W 500m 423m
CAT5e 60W 500m 211m
Note: Higher gauge wiring will allow for longer distances.
Notes:
Altronix is not responsible for any typographical errors.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty
IIPace1PRD Rev. 0116151 I07U MEMBER