Altronix Pace1PRMT User manual

Pace1PRMT - 1 -
Overview:
Pace1PRMT is a long range Ethernet adapter kit which transmits data at 100mbps full duplex and
power via a single twisted pair (UTP) or Cat5e or higher cable in a PoE(+) compliant format. The
Pace1PRM receiver is powered via a PoE midspan such as the Altronix Netway series or by an
endspan. The receiver passes the PoE(+) compliant power over the cable to the Pace1PTM trans-
ceiver which in turn passes this power to an enabled IP camera/device. These plug and play units
facilitate cost effective solutions for IP devices that need to be installed at distances greater than
100m. They also provide a simple way to replace legacy analog products with new IP devices over
single twisted pair (UTP) or structured cable.
Features:
Rev. 111413
Installation Guide
Pace1PRMT
IP and PoE+ Over Extended Distance UTP or CAT5e
Pace1PRM Receiver and Pace1PTM Transceiver kit
Agency Listings:
• UL/CUL Listed for Information
Technology Equipment (UL 60950-1).
• CE approved.
• C-Tick compliant.
Input (Pace1PRM):
• Powered by midspan or endspan.
PoE compliant to IEEE 802.3af (15W) and
PoE+ compliant to IEEE 802.3at (30W).
Ethernet:
• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair CAT5 or 1 pair UTP
structured cable.
• Distance: up to 500m (1,640 ft.).
• Speed: 10/100BaseT, half/full duplex, auto
negotiation. PoE compliant to IEEE 802.3af
(15W) and PoE+ compliant to IEEE 802.3at
(30W) delivered to camera by Pace1PTM.
Power provided by Pace1PRM to Pace1PTM
by PoE protocol.*
• Throughput is rated to pass 100mbps of
data at distances up to 500m with
proper headend equipment, this supports
Megapixel, HD720, HD1080.
CAT5e or higher:
• Distance: up to 500m @ 100mbps
(see Maximum Length of Cable Type vs.
Camera Power/PoE Class, pg. 4).
UTP (single pair):
• Distance: up to 152m @ 100mbps
(see Max. Length of Cable Type vs.
Camera Power/PoE Class, pg. 4).
LED Indicators:
• Pace1PRM/Pace1PTM:
Green - PoE ON (by respective RJ45 jack).
• Pace1PRM and Pace1PTM (RJ45 jack):
Yellow and Green LED IP Link status,
10/100Base-T/active.
Environmental:
• Operating Temperature
Pace1PRM/ Pace1PTM:
-- 20ºC to +49ºC (-- 4ºF to 120.2ºF).
• Storage Temperature:
-- 30º to +70ºC (-- 22º to 158ºF).
• Humidity: 20 to 85%, non-condensing.
Functions:
• Auto detection and protection of legacy
non-PoE cameras/devices.
Applications:
• Extend Network link distance in an
industrial environment over 700m
(see note, pg. 2).
• Retrofit digital IP cameras in an analog
CCTV CAT5e wired installations.
• Works with Megapixel, HD720, HD1080
and VGA (SD) cameras (see note, pg. 3).
Mechanical:
• Dimensions (W x L x H approx.):
Pace1PRM/Pace1PTM:
3.5” x 3.5” x 1”
(88.89mm x 88.89mm x 25.4mm).
I.T.E. 43KC
Z1409
* See note on page 3.
All manuals and user guides at all-guides.com
all-guides.com

- 2 - Pace1PRMT
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and
with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or
Recognized wire suitable for the application.
Pace1PTM and Pace1PRM are not intended to be connected to outside plant leads and should be
installed indoors within the protected premises. Pace1PRM and Pace1PTM are intended for indoor
use only.
1. Pace1PRM installation:
a. Secure unit to desired mounting surface with a proper fastening device utilizing the unit’s
mounting hole (Fig. 2a, pg. 3). Unit should be mounted in proximity to ethernet
switch/network, NVR or video server.
b. Connect structured cable from ethernet midspan or endspan device to RJ45 jack marked
[PoE Input] (Fig. 2, pg. 3).
c. CAT5e or higher: Connect CAT5e or higher to connector marked [RJ45 OUT] (Fig. 2, pg. 3).
UTP: Connect single UTP to connector marked [UTP OUT] (Fig. 2, pg. 3).
2. Pace1PTM installation:
a. Secure unit to desired mounting surface with a proper fastening device utilizing the case’s
mounting hole (Fig. 2a, pg. 3). Unit should be mounted in proximity of camera/device.
b. Connect structured cable from IP camera/device to RJ45 jack marked [PoE Out] (Fig. 2, pg. 3).
c. CAT5e or higher: Connect CAT5e or higher to connector marked [RJ45 IN] (Fig. 2, pg. 3).
UTP: For single UTP applications, jumpers (supplied) must be connected as follows:
1. Remove the four (4) screws from the Pace1PTM cover. Do not discard hardware.
2. Connect jumpers (supplied) to pins pairs [P5] and [P6] as shown (Figs. 1a & 1b, pg. 3).
3. Replace cover and secure it with the four (4) screws.
4. Connect UTP to connector marked [UTP IN].
Technical Specifications:
Parameter Description
Connections RJ45 for ethernet link or single pair UTP.
Input power
requirements
Midspan or endspan port connected.
PoE compliant to IEEE 802.3af (15W) and
PoE+ compliant to IEEE 802.3at (30W)
Indicators
Yellow (RJ45 connector): On - Link, Off - No Link, Blinking - Activity.
Green (RJ45 connector): On - 100Base-TX, Off - 10Base-T.
Green: PoE Active.
Environmental
Conditions
Operating Ambient Temperature: UL60950-1
Pace1PRM: -- 20ºC to +49ºC (-- 4ºF to 120.2ºF).
Pace1PTM: -- 20ºC to +49ºC (-- 4ºF to 120.2ºF).
Relative humidity: 20 to 85%, non-condensing.
Storage Temperature: -- 30º to +70ºC (-- 22º to 158ºF).
Operating Altitude: -- 1000 to 6,561.679 ft. (-- 304.8 to 2000m).
Regulatory
Compliance
UL/CUL Listed for Information Technology Equipment (UL 60950-1).
CE approved. C-Tick compliant.
Weights (approx.) Product: 3.88 oz. (0.11 kg.), Shipping: 6.70 oz. (0.19 kg.)
All manuals and user guides at all-guides.com

Pace1PRMT - 3 -
Structured
Cable to
Midspan/
Endspan
Green LED
indicates
PoE Present
from Midspan/
Endspan
Green LED
indicates
PoE being
transmitted
to Pace1PTM
CAT5 or higher
from Pace1PTM
Single UTP
from
Pace1PTM
Structured
Cable from
Camera/Device
Green LED
indicates
PoE transmitted
to Camera/Device
Green LED
indicates
PoE received
from Pace1PRM
CAT5 or higher
from Pace
receiver
Single UTP
from
Pace1PRM
*Note: Caution, once PoE connection is established between Pace1PRM and Pace1PTM, discon-
nection from Pace1PTM will not disable the PoE output voltage on the Pace1PRM, although the
Pace1PTM can be reconnected, caution should be taken not to connect the CAT5e or single UTP
wiring from Pace1PRM to any non-PoE device.
PoE compliant
100m max.
100m max.
Mounting Hole
PoE Camera
Pace1PTM
Pace1PRM
I.T.E. 43KC
RJ45
Link
Z1409
UTP
Link
RJ45 LEDs Yellow - Activity
Green - Speed
Green LED Power and PoE
PoE
Out
Output
PoE
LED
Input
PoE
LED
www.altronix.com
IP-UTP Transceiver
Passes PoE/PoE+
Pace1PTM - Transceiver
RJ45
Link
Output
PoE
LED
Input
PoE
LED
UTP
Link
PoE
Input
I.T.E. 43KC
Z1409
RJ45 LEDs Yellow - Activity
Green - Speed
Green LED Power and PoE
www.altronix.com
IP-UTP Receiver
Passes PoE/PoE+
Pace1PRM - Receiver
Structured Cable
or Single UTP
Legend:
PoE+ over CAT5e up to 500m max.
or
Single UTP up to 152.4m max.
Powered Switch or NetWay MidSpan
Single PoE Camera Connection Utilizing Pace1PRM and Pace1PTM:
Fig. 2 Fig. 2a
Pace1PRM Pace1PTM
To access pins which are located behind
the UTP Link you must remove cover.
Note: Make sure jumpers are lined up
with pins pairs [F5] and [F6] as shown
in top and side views noted in
Figs. 1a & 1b.
Fig. 1
Fig. 1a Fig. 1b
Side View
Top View
UTP
Link P5
Jumper
P6
P5 P6
All manuals and user guides at all-guides.com

- 4 - Pace1PRMT
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: [phone]
website: www.altronix.com, e-mail: [email protected]. Lifetime Warranty, Made in U.S.A.
IIPace1PRMT K04O MEMBER
PoE Camera
PoE Camera
PoE Camera
PoE Camera
PoE+ over CAT5e up to 500m (1,640 ft.) max.
or Single UTP up to 152.4m (500 ft.) max.
PoE+ over CAT5e up to 500m (1,640 ft.) max.
or Single UTP up to 152.4m (500 ft.) max.
PoE+ over CAT5e up to 500m (1,640 ft.) max.
or Single UTP up to 152.4m (500 ft.) max.
PoE+ over CAT5e up to 500m (1,640 ft.) max.
or Single UTP up to 152.4m (500 ft.) max.
100m (328 ft.) max.
100m (328 ft.) max.
100m (328 ft.) max.
100m (328 ft.) max.
PoE compliant
100m (328 ft.) max.
PoE compliant
100m (328 ft.) max.
PoE compliant
100m (328 ft.) max.
PoE compliant
100m (328 ft.) max.
Structured Cable
or Single UTP
Legend:
Pace1PRM
Pace1PRM
Pace1PRM
Pace1PRMPace1PTM
Pace1PTM
Pace1PTM
Pace1PTM
Powered Switch or
NetWay MidSpan
Multiple PoE Cameras Connection:
Fig. 3
Maximum Length of Cable Type vs. Camera Power/PoE Class:
Cable Type Total Power
Consumption
Max.
Data Distance
Max.
Power Distance
CAT5e 15W 500m 846m
30W 423m
Cable Type Total Power
Consumption
Max.
Data Distance
Max.
Power Distance
Single UTP
(23AWG)
15W 152m 266m
30W 133m
Note: Calculations based on 56VDC starting voltage from power source and accounts for a
10VDC voltage drop. IEEE standards voltage range requirement for powered devices are:
PoE (15W) - 37VDC to 57VDC
PoE+ (30W) - 44VDC to 57VDC.
All manuals and user guides at all-guides.com