Altronix NetWaySP4 User manual

NetWaySP4WP
- Dual Fiber Optic SFP 1G Link,
4-port PoE+ switch and power supply.
- NEMA4/4X, IP66 rated Outdoor enclosure.
NetWaySP4WPX
- Dual Fiber Optic SFP 1G Link,
4-port PoE+ switch and power supply.
- NEMA4/4X, IP66 rated Outdoor enclosure.
- Accommodates up to four (4)
12VDC/4AH batteries.
NetWaySP4X
- Dual Fiber Optic SFP 1G Link,
4-port PoE+ switch and power supply.
- NEMA1 rated Indoor enclosure.
NetWaySP4WPN
- Dual Fiber Optic SFP 1G Link and
4-port PoE+ switch
(uses external power supply).
- NEMA4/4X, IP66 rated Outdoor enclosure.
NetWaySP4PL
- Dual Fiber Optic SFP 1G Link,
4-port PoE+ switch and power supply.
- Backplane version.
NetWaySP4B
- Dual Optic SFP 1G Link and
4-port PoE+ switch
- Board only.
DOC#: NetWaySP4 Rev. 032917 More than just power.TM
Installing Company: _______________ Service Rep. Name: __________________________________
Address: _____________________________________________ Phone #: __________________
Installation Guide
I.T.E. 43KC
NetWaySP4 Series
4-Port Ethernet over Fiber
PoE+ Hardened Switches
Models Include:
™
Embedded
Fiber Solution

- 2 - NetWaySP4 Series Installation Guide
Table of Contents:
Overview .................................................................pg. 3
Features .................................................................pg. 3
Mounting Instructions .......................................................pg. 4
Installation Instructions......................................................pg. 4
Recommended Altronix SFP Modules ...........................................pg. 5
Technical Specifications .....................................................pg. 5
Configuring Units for Network Connection .......................................pg. 6
Factory Default Settings.....................................................pg. 6
Network Settings ..........................................................pg. 6
Static ..................................................................pg. 6
DHCP ..................................................................pg. 6
Secure Network Setup ......................................................pg. 7
Factory Reset Option........................................................pg. 7
VLans....................................................................pg. 8
VLan Setup Drawing ........................................................pg. 9
Typical Applications Drawings ................................................pg. 10-11
Wall Mount Installation ......................................................pg. 12
Pole Mounting Using Optional Pole Mount Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 12
Mechanical Drawings and Dimensions..........................................pg. 13-16

NetWaySP4 Series Installation Guide - 3 -
Overview:
Altronix NetWay Indoor/Outdoor Ethernet over Fiber PoE Hardened Switches provide two (2) 1Gb SFP ports and
four (4) PoE+ (30W) ports or up to two (2) Hi-PoE (60W) ports, passing data and power to PoE/PoE+ compliant
devices. Cameras/edge devices may be located up to 100m from the unit. Features also include an integral battery
charger for applications requiring backup and embedded LINQ Technology to monitor, control, and report power
and diagnostics from anywhere.
Features:
Agency Listings:
• UL/cUL Listed for Information Technology
Equipment (UL 60950-1),
Information Technology Equipment to Be
Installed Outdoors (UL 60950-22).
• CE European Conformity.
Input:
• 115VAC, 60 Hz, 2.5A or 230VAC, 50/60 Hz, 1.3A.
NetWaySP4B/NetWaySP4WPN:
48-55V UL Listed ITE power supply (up to 120W)
Power Output:
• Four (4) ports PoE+ (30W) or up to
two (2) Hi-PoE (60W) ports.
• IEEE 802.3at (30W) and IEEE 802.3af (15W) compliant.
• 120W total power.
• Integral surge protection.
Fiber Port:
• Two (2) Gigabit SFP ports.
• Use with SFP module 1000Base-X (1Gb),
compliant to Class 1 laser product (not included).
Ethernet Ports:
• Four (4) 10/100/1000 Mbps ports.
• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair CAT5 or better structured cable.
• Distance: up to 100m.
• Speed: 10/100/1000 Mbps, half/full duplex,
auto negotiation.
Battery Backup:
• Built-in charger for sealed lead acid or
gel type batteries.
• Battery charging circuit: 48VDC, 300mA.
• Automatic switch over to stand-by battery
when AC fails.
LEDs:
• Individual PoE On LEDs for each port.
• Individual IP Link status, 10/100Base-T/active
LEDs for each port.
• ALOS LED indicates fiber connection for SFP port.
• Heartbeat LED indicates proper operation of the unit.
LINQ Technology:
• Remote network management allows for camera/
device reset and monitoring.
• PoE port management via Dashboard
IP management program.
• Provides local and/or remote access to critical
information via LAN/WAN.
• Email and Windows Dashboard Alert notifications
report real-time diagnostics.
• Event log tracks history.
Environmental:
• Refer to Technical Specifications Chart on page 4
for Environmental Conditions.
VLAN:
• Multiple management VLAN assignment.
• 802.1Q Tagged VLAN.
• Up to 6 VLAN groups. ID Range 2-4095.
Applications:
• Provides PoE / PoE+ / Hi-PoE for cameras/devices.
• Altronix Spectrum switches can be used as a
switching node in daisy chain and ring network
configurations.
• Spectrum switches can pass VLAN 802.IQ protocol.
• Spectrum switches can pass SNMP protocol.
Accessories:
NetWaySP1A
• Ethernet over Fiber Media Converter/Repeater -
for applications requiring an additional SFP (Fiber) port
Mechanical:
NetWaySP4WP
• NEMA4/4X, IP66 Rated enclosure for outdoor use.
• Dimensions (H x W x D approx.):
13.31” x 11.31” x 5.59”
(338.1mm x 287.3mm x 142mm).
NetWaySP4WPN
• NEMA4/4X, IP66 Rated enclosure for outdoor use.
• Dimensions (H x W x D approx.):
13.31” x 11.31” x 5.59”
(338.1mm x 287.3mm x 142mm).
NetWaySP4WPX
• NEMA4/4X, IP66 Rated enclosure for outdoor use.
• Accommodates four (4) 12VDC/4AH batteries
(48V of backup).
• Dimensions (H x W x D approx.):
17.53” x 15.3” x 6.67”
(445.3mm x 388.6mm x 169.4mm).
NetWaySP4X
• Dimensions (H x W x D approx.):
13.5” x 13” x 3.25” (342.9mm x 330.2mm x 83mm).
NetWaySP4PL
• Dimensions (H x W x D approx.):
10.75” x 8.875” x 2.375”
(273.1mm x 225.4mm x 60.3mm).
NetWaySP4B
• Dimensions (L x W x D approx.):
5.625” x 4.5” x 0.625”
(158.8mm x 142.9mm x 15.9mm).

- 4 - NetWaySP4 Series Installation Guide
Mounting Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes
and authorities having jurisdiction. All units should be installed by a trained service personnel.
NetWaySP4WP/SP4WPN/SP4WPX Enclosure Mounting and Installation:
1. Remove backplane from enclosure prior to drilling. Do not discard hardware.
Note: Make sure that hardware will not interfere with components of the circuit board.
2. Mark and drill desired inlets on the enclosure to facilitate wiring. Maximum NEMA type 4X rated fittings to
be used are 0.5”. Follow manufacturer’s specifications for the appropriate size opening.
Note: Inlets for conduit fittings should only be made on the bottom of the enclosure.
UL Listed NEMA type 4X rated conduit connector/hubs shall be used for the appropriate size inlets.
3. Clean out the inside of enclosure before remounting circuit board.
4. Mounting NEMA4/4X rated enclosure (Enclosure Dimensions, pgs. 13-16):
Wall mount: Mount unit in desired location. Mark and drill holes to line up with the top and bottom holes of
the enclosure flange. Secure enclosure with appropriate fasteners (e. g. screws and anchors;
bolts and locking nuts, etc.) that are compatible with mounting surface and are of sufficient
length/construction to ensure a secure mount (Fig. 7, pg. 12).
Pole Mount: Refer to Figs. 8 - 11, pg. 12.
5. Mount backplane in enclosure with hardware.
6. To facilitate wire entry utilize weather-tight NEMA rated connectors (supplied), bushings, and cable.
NetWaySP4X Enclosure Mounting and Installation:
1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes
in the enclosure. Install two (2) upper fasteners and screws in the wall with the screw heads protruding.
Place the enclosure’s upper keyholes over the two (2) upper screws; level and secure. Mark the position of
the lower two (2) holes. Remove the enclosure. Drill the lower holes and install two fasteners. Place the
enclosure’s upper keyholes over the two (2) upper screws. Install the two (2) lower screws and make sure to
tighten all screws (Enclosure Dimensions, pg. 13). Secure enclosure to earth ground.
NetWaySP4B/SP4PL Mounting and Installation:
1. Mount board/backplane in the desired location/enclosure
with hardware supplied.
2. NetWaySP4B: Connect 56VDC/120W max power source
to terminal marked [+] and [–].
Note: For proper earth ground connections on NetWaySP4B
fasten metal spacers (provided) to threaded studs at indicated
board mounting holes (shown on the right).
This is recommended for better environmental immunity.
Installation Installation:
1. For NetWaySP4WP, NetWaySP4WPX, NetWaySP4X, and NetWaySP4PL:
Before powering unit, set input voltage selection switch to proper Input Voltage position
(Fig. 5a, pg. 10). Units are factory set for 115VAC.
2. Secure cabinet to earth ground. Connect AC power from overcurrent protective device circuit breaker
(20A @ 115VAC, 60Hz, 16A @ 230VAC, 50/60Hz) to the terminals marked [L, N] on power supply board
(Fig. 5, pg. 10). Use 14AWG or larger for all power connections (Battery, DC output, AC input).
Connect ground lug to earth or green branch wire (12AWG min.).
Note: For NetWaySP4WPN use external 48-55V UL Listed ITE power supply, carefully observing
correct polarity (Fig. 6, pg. 11).
Keep power-limited wiring separate from non power-limited wiring by utilizing separate knockouts/
inlets. Minimum 0.25” spacing must be provided.
CAUTION: Do not touch exposed metal parts. Shut branch circuit power before installing or servicing
equipment. There are no user serviceable parts inside. Refer installation and servicing to qualified
service personnel.
Fig. 1
NetWaySP4B
Factory Reset
Altronix Corp.
Brooklyn, NY US
www.altronix.com
Input:
48V-56VDC
+--
PoE3
PoE4
PORT 4
Metal Spacers

NetWaySP4 Series Installation Guide - 5 -
3. Port Configurations (Fig. 2, pg. 5; Fig. 5b, pg. 10):
Jumper
Jumper
Position
Structured Cable Ports
1234
PORT 2 30W 30W and Data 30W and Data – –
PORT 3 30W – – 30W and Data 30W and Data
PORT 2 60W Data Only 60W and Data – –
PORT 3 60W – – 60W and Data Data Only
4. Connect structured cables from port marked [Port 1] to [Port 4] on NetWay unit to PoE compliant
cameras/edge devices (Fig. 5, pg. 10).
Note: All interconnected devices must be UL Listed.
5. Insert SFP module into port(s) marked [SFP], then connect cable to the SFP module on NetWaySP4B to the
corresponding input of an SFP switch (Fig. 5, pg. 10).
6. Battery Backup (if desired): Connect four (4) 12VDC batteries wired in series to terminals marked
[– BAT +] (Fig. 5, pg. 10), carefully observing polarity.
When use of stand-by batteries is desired, they must be lead acid or gel type.
Note: When batteries are not used, a loss of AC will result in the loss of output voltage.
7. Please ensure that the cover is secured with:
Key lock and screws for NetWaySP4X, security bolt for NetWaySP4WP, NetWaySP4WPN and
NetWaySP4WPX.
Recommended Altronix SFP Modules:
Altronix P1MM, P1SM10, P1AB2K and P1GCE are hot-pluggable SFP fiber transceiver modules and are readily
usable with all Altronix Spectrum fiber optic equipment for 1Gb transmission rates.
P1MM - For use with Multi-Mode Fiber for distances up to 550m.
P1SM10 - For use with Single-Mode Fiber for distances up to 10km.
P1AB2K - For use with Single Strand Single-Mode Fiber for distances up to 2km.
P1GCE - For use with CAT5e or better for distances up to 100m.
Technical Specifications:
Parameter Description
Number of Ports Four (4) ports PoE+ (30W) or up to two (2) Hi-PoE (60W) ports.
Two (2) Gigabit SFP Ports.
Input Power
Requirements
115VAC, 60Hz, 2.5A or 230VAC, 50/60Hz, 1.3A.
NetWaySP4B/NetWaySP4WPN: 48-55V UL Listed ITE power supply
Environmental
Conditions
Operating Ambient Temperature:
NetWaySP4WP/NetWaySP4WPX: 60W: – 40ºC to 75ºC (– 40ºF to 167ºF);
75W: – 40ºC to 70ºC (– 40ºF to 158ºF);
100W: – 40ºC to 55ºC (– 40ºF to 131ºF);
120W: – 40ºC to 45ºC (– 40ºF to 113ºF).
NetWaySP4X: 120W: – 40ºC to 50ºC (– 40ºF to 122ºF).
NetWaySP4B/NetWaySP4WPN: 120W: – 40ºC to 75ºC (– 40ºF to 167ºF).
Relative Humidity: 85%, +/– 5%
Storage Temperature: – 40ºC to 85ºC (– 40ºF to 185ºF).
Operating Altitude: – 304.8 to 2,000m.
Weights (approx.)
Model Product Weight Shipping Weight
NetWaySP4WP
NetWaySP4WPN
NetWaySP4WPX
NetWaySP4X
NetWaySP4PL
NetWaySP4B
10.72 lbs. (4.86 kg)
7.9 lbs. (3.58 kg)
15 lbs. (6.8 kg)
6.85 lbs. (3.11 kg)
2.8 lbs. (1.27 kg)
0.45 lbs. (0.2 kg)
12.1 lbs. (5.49 kg)
10.2 lbs. (4.63 kg)
17.5 lbs. (7.9kg)
7.75 lbs. (3.51 kg)
4.2 lbs. (1.9 kg)
1 lbs. (0.45 kg)
30W 60W
PORT 2
Fig. 2

- 6 - NetWaySP4 Series Installation Guide
Configuring Units for Network Connection
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Please be sure to visit altronix.com for latest
firmware and installation instructions
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Factory Default Settings
• IP Address: 192.168.168.168
• User Name: admin
• Password: admin
1. Set the static IP address for the laptop to be used for programming to the same network IP address as the
NetwaySP4. The default address of the NetwaySP4 is 192.168.168.168, E.I. 192.168.168.200.
2. Connect one end of the network cable to the network jack on the NetwaySP4 and the other to the network
connection of the laptop.
3. Open a browser on the computer and enter “192.168.168.168” into the address bar.
A dialog box Authentication Required will appear requesting both user name and password.
Enter the default values here. Click on the button labeled Log In.
4. The status page of the NetWaySP4 will appear. Click on the tab labeled Network Settings.
This will open the Network Setting screen. In this screen the MAC Address of the NetWaySP4 module will
be found along with the Network Settings and Email Settings.
Network Settings:
In the IP Address Method field select the method that the IP Address for the NetWaySP4 will be obtained
(STATIC or DHCP), then follow the appropriate steps.
Static:
A. IP Address: Enter the IP address assigned to the NetWaySP4 by the network administrator.
B. Subnet Mask: Enter the Subnet of the network.
C. Gateway: Enter the TCP/IP gateway of the network access point (router) being used.
Gateway configuration is required to properly receive emails from the device.
D. HTTP Port: Enter the HTTP port number assigned to the NetWaySP4 module by the network
administrator to allow remote access and monitoring. The default inbound port setting is 80. HTTP is not
encrypted and unsecure. Even though HTTP can be used for remote access, it is recommended primarily
for use with LAN connections.
E. HTTPS Port: Enter the HTTPS port number assigned to the NetWaySP4 module by the network
administrator to allow remote access and monitoring. The default inbound port setting is 443.
Being encrypted and more secure, HTTPS is highly recommended for remote access.
F. Click the button labeled Submit Network Settings.
A dialog box will display “New network settings will take effect after the server is rebooted”. Click OK.
DHCP:
A. After selecting DHCP in the IP Address Method field click the button labeled Submit Network Settings.
A dialog box will display “New network settings will take effect after the server is rebooted”. Click OK.
Next, click on the button labeled Reboot Server. After rebooting the NetWaySP4 will be set in the DHCP
mode. The IP address will be assigned by the router when the NetWaySP4 is connected to the network.
It is recommended to have the assigned IP Address reserved to ensure continued access
(see the network administrator).
B. Subnet Mask: When operating in DHCP, the router will assign the subnet mask values.
C. Gateway: Enter the TCP/IP gateway of the network access point (router) being used.
D. HTTP Port: Enter the HTTP port number assigned to the NetWaySP4 module by the network administrator
to allow remote access and monitoring. The default inbound port setting is 80. HTTP is not encrypted and
unsecure. Even though HTTP can be used for remote access, it is recommended primarily for use with
LAN connections.

NetWaySP4 Series Installation Guide - 7 -
Secure Network Setup (HTTPS):
In order to setup HTTPS for a Secure Network Connection, a Valid Certificate and Key must be used.
Certificates and Key should be in a “.PEM” format. Self Certifications should only be used for testing
purposes as no actual authentication is being performed. In a Self-Certified mode, the connection will still state
that it is unsecure. How to upload Certificate and Key to setup HTTPS:
1. Open Tab Labeled “Security”
2. Select Tab Labeled “Email/SSL”
3. Scroll to bottom under “SSL Settings”
4. Click “Select Certificate”
5. Browse and select valid Certificate to upload from server
6. Click “Select Key”
7. Browse and select valid Key to upload from server
8. Click “Submit Files”
Once the Certificate and Key is uploaded successfully you can proceed with setting up HTTPS in Network Settings.
A. HTTPS Port: Enter the HTTPS port number assigned to the NetWay Spectrum module by the network
administrator to allow remote access and monitoring. The default inbound port setting is 443.
Being encrypted and more secure, HTTPS is highly recommended for remote access.
B. Click the button labeled Submit Network Settings.
A dialog box will display “New network settings will take effect after the server is rebooted”. Click OK.
Factory Reset Option:
1. Power the unit down. Allow approximately 30 seconds for the unit to power down completely.
2. Depress Factory Reset button on NetWaySP4B while reapplying power to the unit (Fig. 3, pg. 7; Fig. 5c, pg. 10).
Continue holding the button until the LEDs on board go through the start up cycle, then release the button.
3. The unit returns to the original factory settings.
Fig. 3
Factory Reset
Factory Reset
Altronix Cor
Brooklyn, NY US
www.altronix.com
NetwaySP4B

NetWaySP4 Series Installation Guide - 8 -
VLans
VLans (Virtual Local Area Networks) are a subnetwork that allow for the grouping together of devices for
improved network traffic as well as providing higher security by allowing greater control over which devices have
access to each other. It is important to plan how you will setup your devices for each vLan.
Configuring vLan on the Altronix NetwaySP4 Series Switch:
1. Ensure Laptop or PC being used to program the vLan settings is on a port that will be assigned to your
first vLan configuration. By default the management portion of the software is assigned to vLan-1,
CAUTION: Changing VID=1, the industry standard VLAN HOST address to any other VID address should be
done with caution and performed only locally, since the change will drop the original HOST connection.
Local access then facilitates a physical reconnection to respective port.
Note: Only this vLan network allows access to IP management.
2. In Network Section click on VLan Tab.
3. Click Add vLan.
4. Enter a name for the vLan.
5. Enter a vLan ID, i.e. 10, 20, etc. Ensure this vLan ID is associated with a vLan setup on the main switch
and that your Laptop or PC being used for programming is on this same ID.
Note: vLan ID could be any value 2-4094.
6. Assign vLan QOS (Quality of Service) priority. 0 = Lowest and 7 = Highest
7. Pick a Trunk port (Tagged Ports). Trunk ports are typically the main connection for network traffic
for each group. They are usually connected to a network switch, WAPs, etc.
8. Pick the Access port(s) (Untagged Ports) associated with the vLan. Access Ports are typically used for
Cameras, etc. If programming locally, ensure your laptop or PC is connected to one of these ports.
9. Save Configuration.
10. Repeat steps 2 - 9 to add another vLan.
If unit is accidently programmed incorrectly and you cannot get into the NetwaySP8 series programming,
physically moving ports of your PC connected to the main switch to a correct port (when being
programmed remotely), or, as a last resort, completing a factory reset locally and reprogramming the unit.
11. Advanced Port Settings:
Unknown VID Packet Forwarding Configuration:
On ingress unknown VID, Foward to a fixed set of ports. By default no forwarding is set.
Configuration on Ingress Untagged Traffic:
Trunk Port action for ingress UNTAGGED packets. By default do not drop packets.
Keep Tag on Egress:
Select if you want ACCESS Port to keep the vLan tag when sending egress packets.
By default tags are stripped.
Preferred VLAN Forwarding:
For ACCESS Ports that belong to more than one VLan. Select preferred vLan to forward UNTAGGED ingress
packets. By default preferred vLan is the last vLan created.

NetWaySP4 Series Installation Guide - 9 -
Typical VLan Setup:
Fig. 4
Example
vLan ID 20
for ports 3-4
Example
vLan ID 10
for ports 1-2
NetwaySP4B
SFP2 ALOS SFP1 ALOS
Trunk
(i.e. VLan ID 10 and 20)
Pass thru
(i.e. VLan ID 10 and/or 20)
PORT 1
PORT 2
PORT 3
PORT 4
Fiber to
Next NetWaySP4
Fiber from
Host Switch
SFP2 SFP1

- 10 - NetWaySP4 Series Installation Guide
Fig.5 - NetWaySP4WP, NetWaySP4WPX and NetWaySP4X Typical Applications:
115/230VAC
Input
48VDC 300mA
to Stand-by
Batteries
To Input of
NetWaySP4B
board Factory Reset
PoE/PoE+
or Hi-PoE
Device
PoE/PoE+
or Hi-PoE
Device
Fiber to
Switch
Factory Reset
PoE1
Altronix Corp.
Brooklyn, NY US
www.altronix.com
10/100/1000
PWR NetwaySP4B
PoE2
PORT1
1000
100
PORT3
1000
100
PORT2
PORT4
SFP2
ALOS
Input:
48V-56VDC
+--
PORT 1
PORT 2
PoE3
PoE4
PORT 3
PORT 4
PORT 2PORT 3
30W
60W
30W
60W SFP Port
SFP2
ALOS
SFP Port
Fiber to the
next Netway Spectrum
Hardened PoE Switch
30W 60W
Operation
5A 250VA
--- DC +- BAT +
115VAC 230VAC
115VAC 230VAC
Input Voltage
Selection Switch
LG N
Input Voltage
Selection Switch
5A 250VA
--- DC +- BAT +
115VAC 230VAC
115VAC 230VAC
LG N
48VDC 300mA
to Stand-by
Batteries
Fig. 5a
Fig. 5b
Fig. 5c
Fig. 5a
*Note: No limit to quantity of daisy-chained units. Daisy chaining only limited to total bandwidth of 1Gbps.
NetWaySP4X - Power Supply Board Orientation NetWaySP4WP and
NetWaySP4WPX Power Supply Board Orientation

NetWaySP4 Series Installation Guide - 11 -
Fig. 6 - NetWaySP4WPN – Typical Application with Composite Cable
Power Distance Chart
Power Requirements Power Cabling Maximum Distance (ft./m)
15W 12/2 11,162’ / 3403m
30W 12/2 5,581’ / 1702m
45W 12/2 3,767 / 1,148m
60W 12/2 2,739’ / 835m
75W 12/2 2,249’ / 686m
90W 12/2 1,872’ / 571m
105W 12/2 1,607’ / 490m
120W 12/2 1,408’ / 429m
15W 16/2 4,415’ / 1,346m
30W 16/2 2,207’ / 673m
45W 16/2 1,490’ / 454m
60W 16/2 1,083’ / 330m
75W 16/2 889’ / 271m
90W 16/2 740’ / 226m
105W 16/2 635’ / 194m
120W 16/2 557’ / 170m
Estimated distances based on starting voltage of 56VDC and accounts for a 10 volt drop.
All distances are per IEEE 802.3at standard for device power requirements of minimum
44VDC and leave an approximate 2 volts for safety and flexibility.
Fiber to the next
Netway Spectrum
Hardened PoE Switch
Factory Reset
PoE1
Altronix Corp.
Brooklyn, NY US
www.altronix.com
10/100/1000
PWR NetwaySP4B
PoE2
PORT1
1000
100
PORT3
1000
100
PORT2
PORT4 SFP2
ALOS
Input:
48V-56VDC
+--
PORT 1
PORT 2
PoE3 PoE4
PORT 3
PORT 4
PORT 2PORT 3
30W 60W 30W 60W SFP Port
SFP2 ALOS
SFP Port
Carefully observe polarity
Carefully observe polarity
PoE/PoE+
or Hi-PoE Device
PoE/PoE+
or Hi-PoE Device
IP PoE/PoE+
Device
Factory Reset
Composite Cable 48-55V UL Listed
ITE Power Supply
Fiber Switch

- 12 - NetWaySP4 Series Installation Guide
Wall Mount Installation:
1- Place unit at desired location and secure with mounting
screws (not included) (Fig. 7, pg. 12).
Fig. 7
Pole Mounting Using Optional Pole Mount Kit
PMK1 (NetWaySP4WP/4WPN) or PMK2 (NetWaySP4WPX):
This installation should be made by qualified service personnel. This product contains no serviceable parts.
PMK1 and PMK2 outdoor pole mount kits are designed to simplify the installation of Altronix outdoor rated
power supplies and accessories housed in models WP1, WP2, WP3 and WP4 NEMA rated enclosures. PMK1
and PMK2 can be mounted on 2” to 8” (50.8mm to 203.2mm) diameter round or 5” (127mm) square poles.
Brackets are designed for use with the Wormgear Quick Release Straps (two included).
1. Thread one (1) wormgear quick release strap through the slots on the back of a mounting bracket (Fig. 8, pg. 12).
2. Once the desired height of the top Pole Mount bracket is achieved, tighten the straps down by sliding open
end of the strap through the locking mechanism on the strap, then tighten the screw with
flat head screwdriver or 5/16” hex socket driver (Fig. 9, pg. 12 and Fig. 10, pg. 12).
3. Attach the bottom bracket to the enclosure by inserting bolts through the flange of the enclosure and into the
bracket, tightening bolts with a 7/16” hex socket (Fig. 10, pg. 12).
4. Thread the second wormgear quick release strap through the slots on the back of the bottom mounting
bracket (Fig. 10, pg. 12).
5. Mount enclosure onto the top bracket by inserting bolts through flange of the enclosure and into the bracket,
tightening bolts with a 7/16” hex socket (Fig. 9, pg. 12).
6. Tighten the straps of the bottom bracket down by sliding the open end of the strap through the locking
mechanism on the strap, then tighten screw with flat head screwdriver or 5/16” hex socket driver
(Fig. 10, pg. 12).
7. Clip excess straps.
Fig. 7 Fig. 8 Fig. 9
Fig. 10
Fig. 11
2” to 8”(50.8mm to 203.2mm)
diameter round pole
Fig. 11a
5” (127mm) square pole

NetWaySP4 Series Installation Guide - 13 -
NetWaySP4X
Mechanical Drawing and Dimensions (H x W x D approx.):
13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.6mm)
1.40”
(35.6mm)
1.40”
(35.6mm)
1.40”
(35.6mm)
4.85” (123.2mm) 4.85” (123.2mm)
3.25” (82.6mm)
0.75”
(19.1mm)
0.75”
(19.1mm)
11.0” (279.4mm)
12.5” (317.5mm)
1.20”
(30.5mm)
1.20”
(30.5mm)
0.9375” (23.8mm)
0.9375” (23.8mm)
5.10” (129.5mm)
1.40”
(35.6mm)
5.10” (129.5mm)
6.5625” (166.7mm)
3.25” (82.6mm)3.25” (82.6mm)
3.25” (82.6mm)
10.5” (266.7mm)
1.0”
(25.4mm)
1.0”
(25.4mm)
1.0” (25.4mm)
13.0” (330.2mm)
5.10” (129.5mm)
1.20”
(30.5mm)

- 14 - NetWaySP4 Series Installation Guide
NetWaySP4PL
Mechanical Drawing and Dimensions (H x W x D approx.):
10.75” x 8.875” x 2.375” (273.1mm x 225.4mm x 60.3mm)
10.75” (273.1mm) 10.25” (260.3mm)
8.875” (225.4mm)
8.25” (209.5mm)
0.25” (6.4mm)

NetWaySP4 Series Installation Guide - 15 -
NetWaySP4WP and NetWaySP4WPN
Mechanical Drawing and Dimensions (H x W x D approx.):
13.31” x 11.31” x 5.59” (338.1mm x 287.3mm x 142mm)
5.59” (142mm)
PADLOCK LATCH ATTACHED
WITH RIVETS (Ø 0.375” (9.5mm) PADLOCK EYE)
Ø 0.32 (8.1mm)
MOUNTING HOLE
TYP. 4 PLACES
8.00” (203.2mm)
STAINLESS STEEL PIANO HINGE
10.75” (273.1mm)
10.00” (254mm)
8.25” (209.6mm)
10.25” (260.4mm)
12.00” (304.8mm)
13.50” (342.9mm)
10-32 X 0.25” (6.4mm)
BRASS INSERT (X2)
1.61” (40.9mm)
3.96” (100.6mm)
12.75” (323.9mm)
11.31” (287.3mm)
13.31” (338.1mm)
10-32 X 0.375” (9.5mm)
BRASS INSERT (X4)
FRONT VIEW
FRONT VIEW COVER REMOVED
RIGHT SIDE VIEW
END VIEW

- 16 - NetWaySP4 Series Installation Guide
FRONT VIEW COVER REMOVED
RIGHT SIDE VIEWFRONT VIEW
END VIEW
SECTION A-A
AA
316 STAINLESS STEEL PADLOCK LATCH
ATTACHED WITH RIVETS. Ø 0.375 PADLOCK EYE
17.36” (441 mm)
12.00” (304.8mm)
6.41” (162.8mm)
10-32 X 0.250 BRASS INSERT 4 PLCS.
14.54” (369.3mm)
16.74” (425.2mm)
0.125” (3.2mm)
14.25” (362mm)
14.00” (355.6mm)
12.23” (310.6mm)
17.53” (445.3mm)
16.00” (406.4mm)
1.67” (42.4mm) 5.00” (127mm)
16.73” (425mm)
15.3” (388.6mm)
6.67” (169.4mm)
4.94” (125.5mm)
5.77” (146.6mm)
0.75” (19.1mm)
MOUNTING PLATE
Ø 0.32” (8.1mm)
WALL MOUNTING HOLE X 4
NetWaySP4WPX
Mechanical Drawing and Dimensions (H x W x D approx.):
17.53” x 15.3” x 6.67” (445.3mm x 388.6mm x 169.4mm)
Altronix is not responsible for any typographical errors.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty
IINetWaySP4 Series H26U MEMBER