Amana BX521VE User manual

International
Bottom Freezer
Refrigerator
Owner's Manual
Keeptheseinstructionsforfuturereference.Besurethis
manalstayswithrefrigerator.
BX521VE BX521VW

ongratulations on the purchase of your new appliance. This appliance
has been designed and manufactured to give you years of reliable
performance. For best results, carefully read the instructions on how to
install your new appliance. Correct installation will avoid delays and
unnecessary service calls.
Once installation is complete, read this booklet carefully and get to know the
controls and the features of your new appliance.
For appliance please phone
1300 652 100
Kleenmaid St George Store
131308
We reserve the right to alter the specifications with no influence on the
operation of the appliance. This instruction manual cannot be reason for
claim.
C

2
Contents
PartsandAccesories.................................................................... 2
ElectricalRequirements ................................................................ 2
ModelIdentification........................................................................ 2
Service ......................................................................................... 2
ProperDisposal ofYourRefrigerator.............................................. 3
SpaceRequirements..................................................................... 3
Instructionsfor Installation............................................................. 4
ToRemoveDoors and Hinges .................................................. 4
ToReplace Doors ..................................................................... 4
ConnectIce Maker Water Supply Line(somemodels)............... 5
LevelingRefrigerator ..................................................................... 6
InstallationChecklist ..................................................................... 7
Controls ........................................................................................ 8
Fresh Foodand Freezer Controls ............................................. 8
SettingControls......................................................................... 8
Fresh FoodFeatures .................................................................... 8
FreshFoodShelves.................................................................. 8
BeverageOrganizer.................................................................. 8
AdjustableDeli DrawerTM (somemodels)................................... 9
Garden FreshTMCrisper ............................................................ 9
ChillerFreshTM System(somemodels) ..................................... 9
StorageRack(some models)...................................................10
CoveredStorage Bucket (some models)..................................10
DairyCenter(some models) ....................................................10
Door Buckets ...........................................................................11
Tall PackageRetainer ..............................................................11
DoorShelves ...........................................................................11
AdjustableDivider (somemodels) ............................................11
BottleHolder ............................................................................11
FreezerFeatures.........................................................................12
Frost-FreeSystem...................................................................12
AutomaticIce Maker (some models) ........................................12
IceServiceRack(some models) .............................................12
SlideoutShelf (somemodels) ...................................................12
VerticalShelfDivider (somemodels) ........................................12
FixedWire Shelf (somemodels)...............................................12
WireBasket (some models) .....................................................13
IceBin (some models) .............................................................13
Vertical BasketDivider .............................................................13
Tilt-OutBin (some models) .......................................................13
PulloutDrawer Baskets (some models)....................................13
IceShield (some models) .........................................................13
Careand Cleaning .......................................................................14
GeneralCleaning .....................................................................14
StainlessSteelCleaning ...........................................................14
Adhesives ................................................................................14
Door Gaskets ..........................................................................14
CondenserCoils ......................................................................14
GlassShelves..........................................................................14
OdorRemoval..........................................................................14
LightBulbReplacement ............................................................15
VacationTips................................................................................15
EnergyTips..................................................................................15
NormalOperating Sounds ............................................................16
BeforeCalling For Service............................................................17
Note: Translationmaysometimes cause variationsinmeaning.In all
caseswhere meaning varies, the most accuratemeaningwill be the
Englishversion of thisdocument.
!
Recognize this symbol as a safety precaution.
Model Identification
Thank you for purchasing this Amana®refrigerator. Please
read this Owner's Manual thoroughly. This manual
provides proper maintenance information. Any questions,
call the Consumer Affairs Department at 1-800-843-0304
inside U.S.A. and 1-319-622-5511 outside the U.S.A., or
contact us on the internet at www.amana.com.
When contacting Amana , provide product information.
Product information is on the serial plate, located on the
ceiling of fresh food section. Record the following
information.
Model Number: _________________________
Manufacturing Number: _________________________
S/N or Serial Number: _________________________
Date of Purchase: _________________________
Dealer's name and address: ________________________
________________________________________________
Service
Keep a copy of sales receipt for future reference or in
case warranty service is required. Any questions or to
locate an authorized servicer, call 1-800-NAT-LSVC
(1-800-628-5782) inside U.S.A. 319-622-5511 outside
U.S.A. Warranty service must be performed by an
authorized servicer. Amana also recommends contacting
an authorized servicer if service is required after warranty
expires.
Parts and Accessories
Purchase replacement parts and additional accessories
(e.g. refrigerator shelves) over the phone. To order
accessories for your product, call 1-800-843-0304 inside
U.S.A. or 319-622-5511 outside U.S.A., or contact us on
the internet at www.amana.com.
Electrical Requirements
WARNING
!
To avoid electrical shock which can cause severe
personal injury or death do not cut or remove the round
grounding prong from the plug. Refrigerator must be
grounded at all times. Do not remove warning tag from
power cord.
Do not use a two-prong adapter. Do not use an
extension cord.
This refrigerator is equipped with a three-prong
(grounding) plug for protection against possible
shock hazards. If a two-prong wall receptacle
is encountered, contact a qualified
electrician and have the two-prong wall
receptacle replaced with a properly grounded
three-prong wall receptacle in accordance
with the National Electrical Code.
Refrigerator is designed to operate on a separate 230
volt, 10 amp., 50 Hz line.

3
Space Requirements
WARNING
!
Keep flammable materials and vapors, such as
gasoline, away from refrigerator. Failure to do so can
result in death, explosion, fire, or burns.
•To ensure proper ventilation for your refrigerator, allow
for a 1"(2.5 cm) for 33" wide models, or ½"(1.3 cm) for
30" wide models, at the top of your refrigerator.
• If your refrigerator has an ice maker, make sure you
leave some extra space at the back to allow for the
water line connection. The refrigerator can be flush with
the back wall if you do not have an ice maker installed.
• If you are installing your refrigerator next to a fixed wall,
leave 2 ½" minimum on hinge side (depending on your
model) to allow for the door to swing open 90°.
NOTE: Do not install the refrigerator near an oven,
radiator, or other heat source. Do not install the
refrigerator in a location where the temperature will fall
below 55°F (13° C).
discard an old refrigerator, please follow the
instructions below to help prevent accidents.
BEFOREBEFORE
BEFOREBEFORE
BEFORE
YY
YY
YOUOU
OUOU
OU
THRTHR
THRTHR
THROO
OO
OW AW A
W AW A
W AWW
WW
WAA
AA
AYY
YY
YYY
YY
YOUR OLDOUR OLD
OUR OLDOUR OLD
OUR OLD
REFRIGERAREFRIGERA
REFRIGERAREFRIGERA
REFRIGERATT
TT
TOR OR FREEZER:OR OR FREEZER:
OR OR FREEZER:OR OR FREEZER:
OR OR FREEZER:
• Take off the doors.
• Leave the shelves in place so that children may
not easily climb inside.
DANGER
!
Proper Disposal ofYour Refrigerator
IMPORTANT: Child entrapment and suffocation
are not problems of the past. Junked or abandoned
refrigerators are still dangerous--
even if they will sit for "just a few days." If you

4
IMPORTANT:
• Save all screws for reuse.
• For plug removal requiring use of flat blade screwdriver
or putty knife, blade of tool must be covered with
masking tape to avoid damage to refrigerator
finish. For plugs using a screwdriver or nut driver style
head, use appropriate tool to avoid damage to plugs.
To Remove Doors and Hinges
Some installations may require door and hinge removal to
transport unit to final location.
WARNING
!
To avoid electrical shock which can cause severe
personal injury or death, disconnect power to
refrigerator before removing doors. After replacing
doors, connect power.
1. Remove top hinge cover
(A) . Top hinge cover snaps
off. While supporting refrigerator door, remove top
hinge
(B) and shim (C) using 5/16" hex nut driver to
remove screws
(D) .
A
B
D
C
2. Lift refrigerator door off center hinge.
3. While supporting freezer door, remove center hinge pin
(A) from center hinge bracket (B) with 5/16" hex nut
driver. Remove and retain all round washer shims
(C–
some models)
.
B
C
A
4. Remove freezer door by lifting door off bottom hinge.
Instructions for Installation 5. Remove center hinge bracket
(A) and shim (B) by
removing screws
(C) using Phillips screwdriver.
BA
C
6. Remove toe grille (A) and bottom hinge cover (B) . Both
snap off.
7. Remove bottom hinge
and shim (C) with 3/8" hex nut
driver. Remove hinge pin
(D) . Remove and retain all
round washer shims
(E) , if present.
B
A
D
C
E
To Replace Doors
1. Replace bottom hinge and shims with 3/8" hex nut
screws from hinge removal.
2. Replace bottom hinge pin
(A) in hinge bracket
hole
(B) toward outside of cabinet. Replace all washer
shims
(C–some models) .
A
B
C
3. Replace center hinge and shims with Phillips screws
from hinge removal.
4. Place freezer door on bottom hinge pin.
5. Replace center hinge pin with 5/16" hex nut driver.
Make sure fit is tight. Replace all washer shims
(some models) .
6. Assemble top hinge, hinge shim, and positioning
shim together. Attach loosely to opposite side of
cabinet to allow for door clearance.
Proper installation will ensure this
refrigerator operates most efficiently.
Amana cannot be held responsible for
improper installation.
Tools Required
Putty knife 5/16" hex nut driver
Masking tape ¼" hex nut driver
3/8" hex nut driver Phillips screwdriver

5
7. Place refrigerator door on center hinge.Tighten down
top hinge to securely hold door.
8. Use a dime at top to space door 11/16"(18 mm)from
cabinet. Handle side of door should be approximately
1/8" (3 mm) higher than hinge side. Door will become
level when it is loaded with food.
1/8"
(3 mm)
11/16"
(18 mm)
9. Replace hinge cover.
Note: If automatic ice maker water supply is
required, procede to
Connect Ice Maker Water
Supply Line
. If not, procede to section entitled
Leveling Refrigerator .
Connect Ice MakerWater Supply Line
(some models)
DANGER
!
To avoid electrical shock which can cause severe
personal injury or death. Disconnect power to
refrigerator before connecting water supply.
CAUTION
!
Observe the following to avoid property damage:
• Raise stabilizing leg before moving unit.
• Make sure water pressure to water valve is
between 20 and 100 pounds per square inch.
• Tighten adapter fitting and nuts with pliers and
wrenches. Do not overtighten.
• Check for water leaks and correct if necessary
before returning refrigerator to normal location. After
24 hours check again for leaks.
Important
• Before connecting water supply, contact a plumber to
connect coper tubing to household plumbing in
compliance with local codes and ordinances.
•DO NOT use piercing type or 3/16" saddle valves!
Both reduce water flow, become clogged with time and
in addition, may cause leaks if repair is attempted. The
correct type–a shut-off valve–requires a ¼" hole to be
drilled in the water supply pipe before valve attachment.
• Do not install copper tubing in area where temperatures
drop below 32°F (0°C).
Materials Required
¼" O.D. (6 mm) flexible copper tubing
½" open end wrench
Length of copper tubing must reach from water supply
connection to water valve inlet port on back of
refrigerator, plus additional 8 ft. (2 m) of tubing for a
service loop. A service loop will allow refrigerator to be
pulled away from the wall without disconnecting tubing.
Procedure
1. Remove plastic cap
(A) from water valve inlet port (B) .
A
B
2. Place brass nut (A) and brass sleeve (B) on copper
tubing
(C) (Brass nut and sleeve are found in your
literature packet.). Insert copper tubing into water
valve inlet port
(D) . Connect brass nut on copper
tubing to water valve inlet port. Make sure copper
tubing is secure by pulling on copper tubing.
3. Turn on water supply to refrigerator and check for
leaks. Correct any leaks at connection. Be careful not
to overtighten connection.
4. Create a service loop using extreme care to avoid
kinks. Secure copper tubing to refrigerator cabinet
with a "P" clamp
(E) . It is important to secure copper
tubing to refrigerator to avoid leaks when pushing
refrigerator back into opening.
A
B
D
C
E
5. Proceed to Leveling Refrigerator for final refrigerator
placement.

6
Leveling Refrigerator
CAUTION
!
Protect soft vinyl or other flooring with cardboard, rugs
orotherprotectivematerial to avoidpropertydamage.
Ifyourrefrigeratorrequiresanicemakerwatersupply
connection, proceed to Connectice maker water supply
sectionbeforelevelingyour refrigerator.
1. Pluginpowercord.
2. Moverefrigeratorintofinallocation.
3. Level refrigerator using a level placed on top of the
refrigerator.
• Removetoegrille (A) .Removebottom hinge
cover (B) .
• Turn roller adjustment screws (C) toraiseor lower
refrigeratorcabinet.Frontofrefrigerator must be
¼" (6 mm), or ½ bubble on your level, higher than
the back of your refrigerator.
• Make sure refrigerator cabinet is level from side to
side by adjusting left and right roller adjustment
screw (C) .
• Turn stabilizing leg (C) clockwise until firmly against
floor.
4. Replacetoegrille (A) andbottomhinge cover (B) . See
markings on inside of toe grille to insure proper
placement.
•Snap top portion into place first. Press down on
lower part of grille until bottom portion snaps into
place.
AB
C
D
5. Review Installation Checklist in Owner's Manual with
consumer.

7
Installation Checklist
This checklist is for personal records only.
Consumer Installer Doors
Handles are solidly attached to doors.
Handlesideofdooris1/8" (3 mm) higher than hinge side. (Door lowers when
loadedwithfood.)
Doorssealcompletelytorefrigeratorcabinet.
Leveling
Refrigerator is tilted 1/4"(6 mm) from front to rear.
Toe grille is properlyattachedtorefrigerator.
Product Literature
Owner'smanualis reviewed including the followinginformation.
• productregistrationcard
• Fresh foodand freezercontrols
• Humidity-controlledcrispers
• normaloperating sounds
Notes
Consumer's Signature DateInstaller's Company Name/Phone Number
Installer's Signature

8
Controls
This refrigerator is designed to operate at normal
household temperatures of 55° to 110°F (13° to 43°C).
Fresh Food and Freezer Controls
Fresh food control is located on upper rear wall of fresh
food section.
456
7
3
2
1
Freezer control is located on left front ceiling of freezer
section.
4Deepfreeze Control
Cold Coldest
Setting Controls
When freezer control is set to OFF, neither refrigerator nor
freezer sections will cool. Initially, set both controls to 4.
Wait 24 hours for refrigerator and freezer sections to
stabilize temperatures. After 24 hours, adjust controls,
one number at a time, as desired. One is warmest setting
and seven is coldest.
Set controls precisely using a household thermometer
with a temperature range between -5° to 50°F
(-21° to 10°C).
Put thermometer snugly between frozen packages in
freezer section. Wait 5–8 hours. If freezer temperature is
not 0° to 2°F (-17° to -16°C), adjust freezer control one
number at a time. Check again after 5–8 hours.
Put thermometer in a glass of water in middle of fresh
food section. Wait 5–8 hours. If fresh food temperature is
not 38° to 40°F (3° to 4°C), adjust fresh food control one
number at a time. Check again after 5–8 hours.
Fresh Food Features
Fresh Food Shelves
Shelves adjust to meet individual storage needs. Some
models feature Spillsaver TM Shelves and Easy Glide TM
shelves. Spillsaver TM Shelves hold minor spills for easier
cleaning.
CAUTION
!
Make sure shelf is secure before replacing items on
shelf to avoid property damage.
CAUTION
!
Handle tempered glass shelves carefully to avoid
personalinjury or property damage.Shelves may
break suddenly if nicked, scratched, or exposed to
suddentemperature change.
• Remove shelves (A) by lifting up shelf front,releasing
hooks (B) from metal track (C), then pulling out.
• Replace shelves by inserting hooks into metal track
and lowering front of shelf.
AC
B
Easy Glide™ shelves pull forward for easy access to
items in back.
Beverage Organizer (some models)
The beverage organizer slides out from underneath the
glide-out shelf. This may hold 12 cans or other desired
beverages.
• Before removing organizer, empty contents.
• Remove organizer
(A) by pulling organizer forward until
it catches on grooves
(B) in shelf rail (C) . Lift organizer
front and pull out.
• To replace, guide organizer
(A) into shelf rails (C) until
forward movement is stopped by groove
(B) . Lift
organizer front and ease organizer toward back of unit.
C
B
C
A

9
6. Replace crispers and shelves by performing steps
2 through 5 in reverse order.
Note: Be sure to hook shelf frame over notch on top
of support post when replacing shelf frames.
7. Slide crisper glass into place.
To remove or clean crisper drawer assembly for 30"
wide units:
1. Open refrigerator door as wide as possible and
remove crisper drawers.
CAUTION
!
Handle tempered glass shelves carefully to avoid
personal injury or property damage. Shelves may
break suddenly if nicked, scratched, or exposed to
sudden temperature change.
2. Remove glass crisper top by gently pushing up from
underneath. Tilt one end up and pull out.
1
2
3. Raise front of crisper frame free of refrigerator cabinet
rail assembly and pull out of unit.
3
4. Replace crispers and shelf by performing steps 2
through 3 in reverse order.
5. Slide crisper glass into place.
Chiller FreshTM System (some models)
The Chiller FreshTM System features a drawer inside a
sleeve. Freezer air circulates between drawer and sleeve.
This systems keeps food fresh longer and up to 5°F (3°C)
colder than refrigerator temperature.
Adjustable Deli Drawer™ (some models)
• Refer to instructions entitled Spillsaver ™ Shelves for
removingandreplacing shelf.
• Remove drawer and sleeve by lifting and pulling out.
• Replacedrawerbyslidingintoplace.
Garden Fresh™ Crispers
Garden Fresh ™ crispers keep produce fresh longer. Wrap
produce tightly. Do not wash produce before placing in
crispers. Excess moisture could cause produce to spoil
prematurely. Do not line crispers with paper towels. Paper
towels retain moisture.
Garden Fresh ™ crisper control is located below front
shelf trim. Control adjusts humidity in crisper drawers.
Slide control to high for produce with leaves such as
lettuce,spinach or cabbage. Slide control to low for
produce with skins such as cauliflower, corn or tomatoes.
To remove or clean crisper drawer assembly for 33"
wide units:
1. Remove crisper drawer on handle side of unit.
CAUTION
!
Handle tempered glass shelves carefully to avoid
personal injury or property damage. Shelves may
break suddenly if nicked, scratched, or exposed to
sudden temperature change.
2. Remove glass crisper top by gently pushing up from
underneath. Tilt one end up and pull out.
2
1
3. Lift front of crisper shelf frame and remove.
4. Lift front of remaining crisper assembly and remove
support post from center of refrigerator floor.
3
4
5. To avoid interference with door, move remaining
crisper assembly to opposite wall and remove.
5

10
D
A
2
C
B
A
1
C
B
D
E
E
F
FG
G
Chiller FreshTM control (A) is located below front shelf trim.
Control adjusts amount of air circulating around drawer.
Slide control to
COLD for normal refrigerator temperature
and to
COLDER for colder temperature. Ice crystals may
form on drawer or food on
COLDER setting. Cold air
entering the Chiller FreshTM drawer can decrease
refrigerator temperature. Fresh food control may need to
be adjusted to a lower number to compensate for colder
air.
Chiller FreshTM drawer can be moved from the left to the
right side of the refrigerator compartment to accomodate
different storage needs.
To install on left side, see Figure 1. To install on right
side, see Figure 2
1. Remove drawer
(B) by lifting and pulling out. Remove
shelf
(C) by lifting from front, releasing hooks from
metal track
(D) , then pulling out.
2. Remove plastic cap
(E) from back wall of fresh food
section by placing a knife covered with masking tape
underneath cap and pulling forward.
3. Rotate boot
(F) 180° to opposite side.
4. Insert plastic cap in hole
(G) opposite side of fresh
food section. Confirm cap is snugly in place. Cold air
may cause food to freeze if cap is not replaced.
5. Replace shelf by inserting hooks into metal track and
lowering the front. Use slots 4 though 6 only.
6. Replace drawer by sliding in. Make sure boot fits
snugly over air inlet in back wall.
Storage Rack (some models)
Storagerack (A) providesconvenientstorage for a large
bottle, eggs, etc.
• Hang rack by hooking over side of shelf.
A
Covered Storage Bucket (some models)
The covered storage bucket has a lid and removable egg
tray.When tray is removed, bucket will accept standard
egg carton, ice, etc.
Dairy Center (some models)
The dairy center provides convenient storage for butter,
cheese, etc.
• Removedairycenterbylifting door (A) ,pushing
tabs (B) of shelf down on both sides, and pulling out.
• Replace dairy center by sliding in until tabs lock
intoplace,then lowerdoor.
A
B

11
Door Buckets
Door buckets adjust to meet individual storage needs.
• Removedoorbucketsby pushing tabs (A) on both
sides of shelves toward center and pulling bucket
out.
• Replace door buckets by sliding in until tabs lock
intoplace.
A
Tall Package Retainer (some models)
Tall packageretainer (A) keepstall items secure.Retainer
fits on front edge of any refrigerator door bucket or door
shelf.
A
Door Shelves
• Remove door shelves by lifting ends and pulling
out.
• Replace door shelves by placing shelf on glides (A)
andslidingdown.
A
Adjustable Divider (some models)
Adjustable divider keeps items in place and adjusts to
meet individual storage needs. Divider fits in any door
bucket or door shelf.
Bottle Holder (some models)
Bottle holder keeps items in place and adjusts to meet
individual storage needs. Bottle holder fits in any door
bucket or door shelf.

12
CAUTION
!
Make sure shelf is secure before placing items on
shelf to avoid property damage.
Freezer Features
Frost-Free System
The fresh food and freezer sections are completely frost-
free. Defrosting is automatic under normal conditions.
Automatic Ice Maker (some models)
• Make sure ice bucket is in place and ice maker arm (B)
isdown (C) .
B
A
C
• After freezer section reaches normal temperature, the
ice maker fills with water and begins operating. For
optimum ice production, it is recommended that freezer
section be at least half full. Allow 24–48 hours after
installation before first harvest of ice. Ice maker
produces 7 to 9 harvests of ice in a 24-hour period
under ideal conditions.
• After ice is formed, ice maker drops ice cubes into ice
storage bucket. During ice production, ice maker arm
(B)
raises and lowers. When ice storage bucket is full, ice
maker arm turns ice maker off
(A) .
Note: Discard first 3 harvests of ice so any impurities left
in the water line after installation are not consumed.
• If you wish to stop automatic ice production lift ice
maker arm
(A) . A definite click is heard when proper
position is reached. Ice maker arm will remain in that
position until pushed down.
Ice Service Rack (some models)
Install ice service rack (A) by placing ice service rack on
washers
(B) and sliding down.
A
B
Slideout Shelf (some models)
Slide out shelf pulls forward for easy access to items in
back.
• Remove slideout shelf by sliding forward until ball
point
(B) beneath center rail (A) catches in molding
groove.
• Grasp shelf by center rail, pull up, and remove.
• Slide in until ball point falls into molding groove.
A
B
Vertical Shelf Divider (some models)
Install vertical shelf divider by completing the following
steps:
1. Slide prongs of shelf divider beneath desired grill
work, slightly off-center from center rail.
2. Press top of divider down and slide hook assembly
beneath center rail.
12
FixedWire Shelf (some models)
• Remove wire shelf by pulling out. A sharp tug may
be necessary.
• Replace wire shelf by sliding in until back locks in
place.

13
Wire Basket
Wire basket (A) slides out for easy access to items in
back.
• Remove wire basket by lifting and pulling out.
• Replace wire basket by sliding in.
A
Ice Bin (some models)
Ice bin (A) sits below the ice service rack on the wire
freezershelf.
A
Vertical Basket Divider
Install vertical basket divider (A) by completing the
following steps:
1. Align clips on side of divider with rungs in basket
wall.
2. Press top of divider down until divider meets bottom
of basket
To remove divider:
1. Grasp top of divider and pull straight up.
A
Tilt-Out Bin (some models)
The tilt-out bin (A) provides convenient storage for frozen
food items in freezer door and tilts forward for easy
access of those items.
A
Pullout Drawer Baskets (some models)
(Door assembly of drawer removed from illustration for
visual clarity)
To remove and replace top basket:
• Remove basket by pulling basket out to its full
extension and lift out.
• Replace basket by sliding into upper compartment of
freezer.
To remove and replace bottom basket:
• Remove basket by lifting basket from rail guides.
• Replace basket by placing into rail guides.
Ice Shield (some models)
The ice shield is mounted at the back of the pullout
drawer to prevent ice from falling behind the basket
assemblies.
To remove and replace ice shield:
• Slide ice shield to the right to release hooks
(A) from
vertical wire rungs.
• To replace, slide tab
(B) into place as shown.
BA

14
Door Gaskets
1. Clean door gaskets every 3 months according to
GeneralCleaninginstructions.Clean any spills
immediately.
Condenser Coil
Clean condenser coil behind toe grille every 3 months to
ensuremaximumperformanceof refrigerator.
Accumulated dust and lint may cause the following:
• reducedcooling performance
• increasedenergy usage
• prematurepartfailure
1. Removetoegrillebyholdingendsandpulling away
fromrefrigerator.
2. Clean front surface of condenser coil with a vacuum
cleanerhosenozzle.
3. Replace toe grille by inserting clips in holes and
snappingin.See LevelingRefrigerator section.
4. Raise stabilizing legs (some models) by turning
counterclockwise.
CAUTION
!
Protect soft vinyl or other flooring with cardboard, rugs
or other protective material to avoid property damage.
5. Pullrefrigeratorawayfromwall.Runavacuum
brush across grilleonbackof refrigerator.
Glass Shelves
CAUTION
!
Handle tempered glass shelves carefully to avoid
personalinjury or property damage.Shelves may
break suddenly if nicked, scratched, or exposed to
suddentemperature change.
Remove shelf by lifting front, releasing hooks from metal
track then pulling out. Place shelf on a towel. Allow shelf
toadjusttoroomtemperaturebeforecleaning.
Clean crevices by completing the following:
1. Dilute mild detergent and brush solution into crevices
using a plastic bristle brush. Let sit for 5 minutes.
2. Spray warm water into crevices using faucet spray
attachment.
3. Dry shelf thoroughly and replace shelf by inserting
hooks into metal track and lowering it from the front.
Odor Removal
1. Remove all foodand disconnect powerto refrigerator.
2. Clean all interior surfaces including ceiling, floor, and
wallsaccordingtoGeneral Cleaning instructions
above.Pay special attention to corners, crevices, and
grooves.Includealldrawers,shelves,andgaskets.
3. Connectpowerto refrigerator and returnfoodto
refrigerator.Wash anddryallcontainers.Wrapfoods
in tightly sealed containers to prevent further odor.
Care and Cleaning
WARNING
!
Disconnectpowerto refrigerator before cleaning to
avoid electrical shock which can cause severe
personalinjuryordeath.Aftercleaning,restore power.
CAUTION
!
Readandfollow all manufacturer’scleaningdirections
toavoid personal injury or propertydamage.
General
See section on Stainless Steel Cleaning if doors are
stainlesssteel.
1. Wash surfaces with 4 tablespoons baking soda
dissolved in 1 quart warm water and a soft, clean
cloth.
2. Rinse surfaces with warm water.Dry surfaces with a
soft, clean cloth.
• Do not use the following items:
- abrasiveorharshcleaners, ammonia,
chlorine bleach, etc.
- concentrateddetergentsorsolvents
- metalscouringpads
These items can scratch, crack and discolor
surfaces.
• Do not place buckets, shelves, etc. in dishwasher.
Stainless Steel Cleaning
Damage to stainless steel finish due to improper use
of cleaning products, or using non-recommended
cleaining products,is not covered under warranty.
ForAmanarecommended products, call our Consumer
Affairs division at 1(800) 843-0304, or contact us on the
internetatwww.amana.com.
1. Wash surfaces with warm soapy water and a soft,
clean cloth or sponge.
2. Rinse surfaces with warm water.Dry surfaces with a
soft, clean cloth.
• Do not use the following harsh cleaners:
- abrasiveoracidic cleaners(ammonia, chlorine
bleach,vinegar-basedproduct, etc.
- citrus-basedcleaners
- scouring pads(metal, textured plastic, etc.)
These items can scratch, discolor, or permanently
tarnish surfaces.
3. Follow up rinsing by immediately drying with a soft,
clean cloth. This will avoid water spotting on
stainless steel finish.
Adhesives
1. Removeadhesiveresidue from refrigerator surfaces
by rubbing toothpaste into adhesive with fingers until
adhesiveloosens.
2. Rinse surface with warm water.Dry surface with a
soft, clean cloth.

15
After 24 hours, check if odor has been eliminated.
Complete steps 4–9 if odor has not been eliminated.
4. With unit unplugged, place crispers on top shelf of
refrigerator section.Packrefrigerator and freezer
sections, including doors, with crumpled sheets of
newspaper.
5. Placecharcoalbriquettes randomly throughout
newspaper.
6. Closedoorsandletstand24–48hours.
7. Removecharcoal briquettes andnewspapers.
8. Completesteps2–3.
If odor is still not eliminated, contact a customer service
representativewiththenumberlocatedintheModel
Identification section.
Light Bulb Replacement
WARNING
!
Disconnectpowerto refrigerator before replacinglight
bulb to avoid electrical shock which can cause severe
personalinjury or death.After replacing light bulb,
restorepower.
CAUTION
!
Observethefollowingto avoid personal injury or
propertydamage.
• Allow light bulbs to cool
• Wear gloveswhen replacing lightbulb.
Fresh Food Light
• Remove light bulb cover (B) by removing ¼" hex nut
screws (A) .Replacewith appliance bulbno greater
than 25 watts.
• Replace light bulb cover by replacing ¼" hex nut
screws.
A
B
Vacation Tips
Complete the following steps for short vacations.
1. Removeperishable foods.
2. If an ice maker is installed, move ice maker arm to
Off position. (See “Automatic Ice Maker” section)
Complete the following steps for long vacations.
1. Emptyrefrigeratorandfreezersections.
2. Unplugrefrigerator.
3. Cleanrefrigeratorand door gaskets according to
GeneralCleaning instructions in“Careand Cleaning”
section.
4. Prop doors open, so air can circulate inside.
5. If an ice maker is installed, turn off water supply to
refrigerator and move ice maker arm to Off
position.(See“AutomaticIceMaker”sectionpage12)
Energy Tips
This refrigerator is designed to be one of the most energy
efficientrefrigeratorsavailable.Reduce energy use by
observingthefollowing.
• Operateinhousehold temperatures of 55° to110°F(13°
to 43°C) away from heat sources and direct sunlight.
• Setrefrigerator,freezer, andtemperaturecontrolled
meat drawer system controls no colder than necessary.
• Keep freezersectionfull.
• Keep door gaskets clean and pliable.Replace gaskets
ifworn.
• Keep condenser coils clean.
Freezer Light
• Remove light bulb cover (B) by removing ¼" hex nut
screws (A) .Replacewith appliance bulbno greater
than 25 watts.
• Replace light bulb cover by replacing ¼" hex nut
screws.
B
A

16
Normal Operating Sounds
Thisnewrefrigeratormaybereplacingadifferently
designed,lessefficientorsmallerrefrigerator.Today’s
refrigeratorshavenew features and aremoreenergy
efficient.As a result, certain sounds may be unfamiliar.
Thesesoundsarenormalandwillsoonbecome familiar
to you.They also indicate refrigerator is operating and
performingas designed.
1. Freezer control clicks when starting or stopping
compressor.
2. Freezer fan airrushesandwhirs.
3. Sealed system (evaporator andheatexchanger)
refrigerantflowgurgles,popsorsoundslikeboiling
water.
4. Defrost heater sizzles, hisses or pops.
5. Defrost timer sounds like an electric clock and
snaps in and out of defrost cycle.
6. Condenser fan airrushesandwhirs.
7. Compressor hasahighpitchedhumorpulsating
sound and cycles on and off.
8. Ice cubes from ice maker (some models) drop into
ice bucket.
9. Ice maker water valve hookup (somemodels)
buzzes when ice maker fills with water.This occurs
whetherornotrefrigeratoris connected to water
supply.If refrigerator is not connected to water
supply, stop sound by raising ice maker arm to Off
position. Ice maker water valve hookup is located
behindcondenserfan in backofrefrigerator.
Note: Foam insulation is very energy efficient and
has excellent insulating capabilities.However, foam
insulation is not as sound absorbent as
previouslyusedfiberglassinsulation.
8
7
6
5
4
3
2
1

17
Before Calling For Service
Problem Solution
Refrigerator does not
operate. •Make sure freezer control is on.
•Make sure refrigerator is plugged in. If not, firmly plug the cord into a live outlet
with proper voltage.
•Check fuse or circuit breaker. Plug in another item at that wall outlet. If outlet
does not work, replace the fuse or reset the circuit.
•If freezer control is on, light works but 2 fans and compressor are not
operating, refrigerator may be in defrost cycle. Wait 40 minutes to see if
refrigerator restarts.
Refrigerator still will not
operate. •Unplug refrigerator. Transfer food to another refrigerator or place dry ice in
freezer section to preserve food. Call for service.
Food temperature appears
too warm. •See above sections.
•Allow time for recently added warm food to reach refrigerator or freezer
temperature. Adding food warms the refrigerator. It can take a few hours for the
refrigerator to return to normal temperature.
•Check gaskets for proper seal. Gaskets should seal tightly to cabinet.
•Clean condenser coil. See “Condenser Coil” instructions in “Care and
Cleaning” section.
•Adjust refrigerator and or freezer control. See “Setting Controls” instructions in
“Controls” section.
•Freezer or refrigerator light stays on. If light stays on, call service.
•Return air vents behind crisper are blocked restricting airflow. Locate return air
vent behind crispers and remove any debrisis that blocks vents or restricts
airflow.
Chiller Fresh™ System
temperature is too warm. •Slide control to colder setting.
•Adjust freezer control to colder setting. See “Setting Controls” instructions of
“Controls” section.
•Verify Chiller Fresh™ System cap has been moved if drawer has been moved
from left to right side of cabinet. See “Chiller Fresh™ System” section.
Food temperature is too
cold. •Clean condenser coil. See “Condenser Coil” instructions in “Care and Cleaning
section.
•Adjust refrigerator control. See “Setting Controls” instructions in “Controls”
section.
•Adjust freezer control to warmer setting. See “Setting Controls” instructions in
“Controls” section. Allow several hours for temperature to adjust.
•Verify plastic cap is in place near Chiller Fresh™ System. See “Chiller Fresh™
System” section.
Refrigerator runs too
frequently. •It may be normal to maintain constant temperature.
•Doors have been opened frequently or for an extended period of time. When
the door is opened warm humid air is allowed into the refrigerator. The more
the door is opened the more warm air the refrigerator must cool.
•Allow time for recently added warm food to reach refrigerator or freezer
temperature. It can take a few hours for the refrigerator to return to normal
temperature.
•Clean condenser coil. See “Condenser Coil” instructions in “Care and
Cleaning” section.
•Adjust freezer control. See “Setting Controls” instructions in “Controls” section.
•Check gaskets for proper seal. Gaskets should seal tightly to cabinet.
•Freezer light stays on. If light stays on, call service
•Make sure refrigerator is level. See “Leveling Refrigerator” section of
Installation Instructions.

18
Problem Solution
Water droplets form on inside of
refrigerator. •It is normal during high humidity periods or if doors have been opened
frequently.
•Wrap food tightly and wipe off damp containers prior to storing in the
refrigerator to avoid moisture accumulation.
Water droplets form on outside
of refrigerator. •Check door seals for proper seal. Gaskets should seal tightly to cabinet.
•It is normal during high humidity periods or if doors have been opened
frequently.
Chiller Fresh™ System or
crisper drawer does not close
freely (some models).
•Check for a package that may prevent drawer from closing properly.
•Confirm drawer is in proper position.
•Clean drawer channels with warm, soapy water. Rinse and dry thoroughly.
•Apply a thin layer of petroleum jelly to drawer channels.
•Confirm refrigerator is level.
Refrigerator has an odor. •See “Odor Removal” instructions in “Care and Cleaning” section.
Refrigerator makes unfamiliar
sounds or seems too loud. •It may be normal. See “Normal Operating Sounds” section.
Ice cubes have an odor. •See “Odor Removal” instructions in “Care and Cleaning” section.
•Ice maker was recently installed. Discard first few batches of ice to avoid
discolored or off-flavored ice.
•Food has not been wrapped tightly in either refrigerator or freezer
compartment. Rewrap foods since odors may migrate to the ice if food is not
wrapped properly.
•Discard ice and clean ice bucket or trays more frequently. Ice cubes are
porous and absorb odors easily.
•Water supply contains minerals such as sulfur. In some situations a filter may
need to be installed to eliminate taste and odor problems.
Ice cubes stick together or
“shrink”. •Empty ice cube bucket or trays more frequently. If used infrequently, ice cubes
may stick together or shrink.
Ice maker is not producing ice. •Water pressure may be to low or high. Ice maker requires a water pressure of
20-100 psi to function properly.
•Confirm ice maker arm is down. See “Automatic Ice Maker” section.
•Confirm household water supply is reaching water valve. Make sure the water
valve shut off is fully turned on.
•Piercing type or 3/16” saddle valve was used for hookup. Both reduce water flow
and may become clogged with time. Replace these valves with correct type of
saddle valve requiring ¼” hole to be drilled in water supply pipe prior to valve
attachment.
•Confirm ice maker wiring harness is inserted completely in proper holes.
•Check for kinks in copper or plastic tubing. Remove kinks or replace tubing.
•Check electrical connections to water valve coil and connector block on
refrigerator cabinet.
•If a water filter has been installed on the water line outside the refrigerator,
check the filter for clogs or improper installation of the filter.
Ice maker is not producing
enough ice. •Ice maker has just recently been installed or a large amount of ice has just
been used. Wait 24 hours for ice production to begin and for ice maker to
restock after emptied.
•Confirm household water supply is reaching water valve. Make sure the water
valve shut off is fully turned on.
•Piercing type or 3/16” saddle valve was used for hookup. Both reduce water flow
and may become clogged with time. Replace these valves with correct type of
saddle valve requiring ¼” hole to be drilled in water supply pipe prior to valve
attachment.
•Check for kinks in copper or plastic tubing. Remove kinks or replace tubing
•Confirm freezer section is operating at proper temperature and that freezer is,
at least, half-full. Freezer must be cold enough to produce ice. See ‘Setting
Controls” section.
Ice forms in inlet tube to ice
maker. •Check water pressure. Low water pressure causes valves to leak.
•Piercing type or 3/16” saddle valve was used for hookup. Both reduce water flow
and may become clogged with time. Replace these valves with correct type of
saddle valve requiring ¼” hole to be drilled in water supply pipe prior to valve
attachment.

DOMESTICWARRANTY-FULLFIVEYEARWARRANTY
In addition to all statutory rights which you, the Consumer, have under the relevant laws in
respectofthisappliance,duringthefirst five years of ownership asthe original purchaser of
this Kleenmaid appliance, we guarantee that any fault caused by faulty material or
workmanship becoming apparent will be rectified free or charge for parts and labour,
provided that all service is performed during normal working hours by Kleenmaid or their
designatedAgents.Wheretheapplianceisinstalledoutsidethenormalservicingareaofthe
above, the Purchaser must pay for the cost of transporting the appliance to and from the
AgentortheAgent’stravellingcosttoandfromthePurchaser’shome.
COMMERCIALWARRANTY-ONEYEARWARRANTY
Whenthis appliance isinstalledin a commercialapplication, inadditionto all statuoryrights
which you, the Consumer, have under the relevant laws in respect of this appliance, during
your first one year of ownership as the original purchaser of the Kleenmaid appliance, we
guarantee that any fault caused by faulty material or workmanship becoming apparent, will
be rectified free of charge for parts and labour, provided that all service is performed during
normal working hours by Kleenmaid or their designated Agents. Where the appliance is
installedoutsidethenormalservicingareaoftheabove,thePurchasermustpayforthecost
oftransportingthe appliance toandfromtheAgentortheAgent’s travelling costtoandfrom
thePurchaser’shome.
WHATTHESEWARRANTIESDONOTCOVER
Wearenotresponsibleforanydamageormalfunctionunlesscausedbyadefectinmaterial
orworkmanship. Thisincludesbut isnotlimited to abuse,misuse, improper installationand
transportation damage. We are not responsible for any consequential damages from any
malfunction.
WARRANTY DOES NOT COVER REPLACEMENT OF LIGHT
GLOBESORGLASSBREAKAGEDUETOIMPACT
Incaseoffracturedglassdonotuseyourappliance.
WARRANTYREGISTRATION
Please complete the enclosed warranty card and retain it together with your proof of
purchase document. These documents will need to be viewed by our service
representativeshouldyourequestinwarrantyservice.
SERVICEASSISTANCE
Toassistyou when phoning ourAfterSalesServicenumbertoarrangeaservicecallplease
completethefollowingdetailsandhavethemreadywhenyoucall.
Model Number:........................................................... Date ofpurchase:....................................
Kleenmaid Storepurchased from:............................... Date ofinstallation:.................................
Your Postcode:...................................................
WARRANTY AND SERVICE