Amantii CUBE-2025WM Operating instructions

CUBE-2025WM
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE
Version:202107
INSTALLATION /OWNER’S MANUAL

2
TABLE OF CONTENTS
Contents
IMPORTANT INSTRUCTIONS ......................................................................................................................................... 3
FCC CAUTIONS .................................................................................................................................................................. 4
UNPACKING AND TESTING THE APPLIANCE .......................................................................................................... 5
GROUNDING THE APPLIANCE ...................................................................................................................................... 5
LOCATING THE FIREPLACE ........................................................................................................................................... 5
CUBE-2025WM .................................................................................................................................................................... 6
INSTALLATION WALL-MOUNT .................................................................................................................................... 7
INSTALLATION CUBE-BASE-LEGS ..............................................................................................................................
INSTALLATION CUBE-BASE-SPEAKER ...................................................................................................................... 9
OUTDOOR INSTALLATION ........................................................................................................................................... 10
HARDWIRE INSTALLATION ........................................................................................................................................ 11
MEDIA OPTIONS .............................................................................................................................................................. 12
DECORATIVE MEDIA INSTALLATION ...................................................................................................................... 12
OPERATION ....................................................................................................................................................................... 13
MANUAL OPERATION ................................................................................................................................................... 13
REMOTE CONTROL OPERATION ................................................................................................................................ 14
WIFI OPERATION ............................................................................................................................................................. 17
REPLACEMENT PARTS .................................................................................................................................................. 20
EXPLODED VIEW ............................................................................................................................................................ 21
WIRING DIAGRAM .......................................................................................................................................................... 22
TROUBLE SHOOTING ..................................................................................................................................................... 23
SERVICE HISTORY .......................................................................................................................................................... 24
WARRANTY ...................................................................................................................................................................... 25
Please read and carefully follow all of the instruction found in this manual. The instructions
included here will assure that you have many years of dependable and enjoyable service
from your Amantii product.

IMPORTANT INSTRUCTIONS
PLEASE RETA N TH S USER GU DE FOR FUTURE REFERENCE
When using electrical appliances, basic precautions should always be followed to reduce the
risk of fire, electric shock, and injury to persons, including the following:
1) Read all instructions before using this fireplace
2) The fireplace is hot when in use. To avoid burns, do not let bare skin touch hot surfaces.
Keep combustible material such as furniture, cushions, bedding, paper, clothes, curtains
at least 3 feet from the front of the unit
3) Extreme caution is necessary when any heater is used near children and whenever the
unit is left operating and unattended.
4) Do not operate a fireplace with a damaged cord or plug, or if the heater has
malfunctioned, the fireplace has drooped or damaged in any manner
5) Not all fireplaces are suitable for use in bathrooms or laundry facilities. Please consult
with individual product literature to confirm suitability
6) Do not run the cord under carpeting. Do not cover cord with throw rugs, runners or the
like. Arrange the cord away from traffic area and where it will not be tripped over
7) Do not modify this fireplace. Use it as described in the manual. Any other use not
recommended by the manufacture may cause fire, shock or injury to persons
8) Do not use this heater with programmer, timer, separate remote-control system or any
other device that switches the heater on automatically, since a fire risk exists if the heater
is covered or positioned incorrectly
9) Disconnect all power supply before cleaning, maintenance or relocation of the fireplace
10) Keep the heater clean. Do not allow any objects to enter any ventilation or exhaust
opening as this may cause electric shock, fire or damage to the heater
11) Do not immerse the cord, plug or any part of the appliance in water or any other liquid
12) n order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this
appliance must not be supplied through an external switching device
CAUTION: Procedures and techniques, which, if not carefully followed, will result in damage to
the equipment.
WARNIN : Procedures and techniques, which, if not carefully followed, will expose the user to
the risk of fire, serious injury, illness or death.
Consult with professional electrician and adhere to all code requirements for
installations in bathrooms
3

FCC CAUTIONS
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: 1) This device may not cause harmful interference, and 2) this device must
accept any interference received, including interference that may cause undesired
operation.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
4

UNPACKING AND TESTING APPLIANCE
Carefully remove the appliance from the box.
Prior to installing the appliance, test to make sure the appliance operates properly by
plugging the power supply cord into a conveniently located 120 olt grounded outlet.
Test all aspects of its operation (manual switches, remote and heater) to make sure all
components operate correctly.
As with most electronic devices
℉
, your new
℃
electric fireplace has been designed to operate at
temperatures between 5 (41 ) and 35 (95 ). During the cold winter months, allow the
fireplace to reach room temperature before turning it on.
NOTE: There may be trace of odor durin the first few minutes of initial use. This is
harmless, normal and will never occur a ain.
GROUNDING APPLIANCE
This appliance is for use on 120 olts. The cord has a plug as shown in (A). An adapter as
shown in (C) is available for connecting three-blade grounding type plugs to two-slot
receptacles. The green grounding lug extending from the adapter must be connected to a
permanent ground such as a properly grounded outlet box. The adapter should not be used if
a three-slot grounded receptacle is available.
To disconnect appliance, turn controls to off, then remove plug from outlet.
LOCATING THE FIREPLACE
Plan where to locate and frame the fireplace. This will save time and money later when you
install the fireplace. Before installation consider the following:
1. Where the fireplace is located must allow for wall and ceiling clearances.
2. Consider a location where the fireplace screen will not be exposed to direct sunlight from
windows or doors.
3. A 15 ampere, 120 olt, 60 Hz branch circuit with proper ground must be available at the
location. Preferably a dedicated branch circuit should be provided to avoid circuit
breakers to trip of fuses to blow.
℃
℉
5

CUBE-2025WM
This appliance has been tested in
accordance with the UL Standard 2021
for fixed and location dedicated
electric room appliances in the United
States and Canada. If you need
assistance during installation, please
contact your local dealer.
NOTE: Th s appl ance must be
electr cally w red and grounded n
accordance w th local codes. In the
absence of local codes, use the
current CSA C22.1 Canad an Electr cal
Code n Canada or the ANSI/NFPA 70
Nat onal Electr cal Code n the Un ted
States.
Description
ELECTRIC FIREPLACE
Voltage 120V AC 60Hz
Watts 1500W Max
NO HEATER 25W
MOTOR HEATER 19W
Appliance Width 19 5/8" or 50 cm
Appliance Height 25 1/4" or 64.1 cm
Appliance Depth 11 3/4" or 30 cm
Gross Weight 50.7 lbs or 22 kgs
Plug Location Left side
Cord Length 70 7/8” or 180 cm
BTU 4800
6

INSTALLATION WALL-
MOUNT
NOTE: Due to the many different materials used on different walls, it is highly recommended
that you consult your local builder before you install this appliance.
1.
Select a location that is not prone to
moisture and is located at least 0.91 m or 3
feet away
from combustible materials such
as curtains or drapes, furniture, bedding,
paper, etc.
2. S
elect a suitable position in whic
the heater horizontally –
use a spirit level to
achieve this (Fig. 1).
3.
Check the wall to ensure there is no wiring,
pipe wires etc.
in the area to be drilled. Drill
8 or more pilot
holes (8mm diameter &
40mm depth) using a suitable size drill a
put the wall plugs into the
holes.
4. Take
out the hanger from the fireplace by
unscrew the screw (Fig.2).
5. Fix the hanger to the wall.
Referring to Fig. 3
6. Avoid
fireplace to move, use screw fix
fireplace to wall (Fig. 4).
Warn ng!
Be sure that the bolts
have been f xed
f rmly enough to w thstand the we ght
Fig. 1
MOUNT
NOTE: Due to the many different materials used on different walls, it is highly recommended
that you consult your local builder before you inst
all this appliance.
Select a location that is not prone to
moisture and is located at least 0.91 m or 3
from combustible materials such
as curtains or drapes, furniture, bedding,
elect a suitable position in whic
h to mount
use a spirit level to
Check the wall to ensure there is no wiring,
in the area to be drilled. Drill
holes (8mm diameter &
40mm depth) using a suitable size drill a
nd
holes.
out the hanger from the fireplace by
Referring to Fig. 3
.
fireplace to move, use screw fix
have been f xed
f rmly enough to w thstand the we ght
！
Fig. 2
Fig.3
Fig. 4
NOTE: Due to the many different materials used on different walls, it is highly recommended
Fig. 2
Fig.3
Fig. 4
7

INSTALLATION CUBE-BASE-
LEGS
1.
Screw the base legs to the steel
2.
Unscrew the adjustable feet from the
bottom of the unit.
LEGS
Screw the base legs to the steel
panel.
Unscrew the adjustable feet from the
3. Place
the unit onto the base leg
in the adjustable feet, fixing the unit and
the base leg.
4. You have completed
the CUBE-BASE-
LEGS.
the unit onto the base leg
and screw
in the adjustable feet, fixing the unit and
completed
the installation of
LEGS.

INSTALLATION CUBE-BASE-SPEAKER
1. Unscrew the adjustable feet from the unit.
2. Unscrew the rear screws and remove the
back steel panel
3. Place the unit on the CUBE-BASE-SPEAKER
and screw in the adjustable feet, fixing the
unit and the speaker box.
4. Plug into the back of the unit. Re-install
the back steel panel.
9

INSTALLATION OUTDOOR
The Cube ( Cube 2025WM) is suitable for installation in outdoor areas protected from direct water
impingement. In addition to maintaining the listed mantel and combustibles clearances, a rain
protection overhang factor of 1/2 shall be constructed to the front and to each side of the installed
appliance. See illustration below. All wiring connections to line power shall be in accordance with local
building code re uirements.
NOTE: The CUBE Wall Mount Un t s approved for outdoor use. The Cube Speaker Base and Cube Leg Base
are NOT approved for use outdoors.
The overhang (A) must extend at least 1/2 the roof-line height (B). Height is measured from the base of the
fireplace.
For example: if the roof-line (B) is 8' above the base of the fireplace, the overhang (A) must be at least 4'.
10

HARDWIRE INSTALLATION
Turn off the appliance completely and let cool before servicing. Only a ualified
should service and repair this electric appliance.
If it is necessary to hard wire this appliance, a ualified electrician must remove the cord connection,
and w
ire the appliance directly to the house hold wiring.
This appliance must be electrically connected and grounded in accordance with local codes, if hard
wired. In the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in
Canada or t
he current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.
1.
Remove the cover plate from the left side of the appliance by removing the two screws, as
shown below.
Unscrew and remove power
2. Attach
the wiring to the junction block. Pl
neutral wire into "N" and the ground wire into
3. Replace the steel plate
and screws
Turn off the appliance completely and let cool before servicing. Only a ualified
should service and repair this electric appliance.
If it is necessary to hard wire this appliance, a ualified electrician must remove the cord connection,
ire the appliance directly to the house hold wiring
.
This appliance must be electrically connected and grounded in accordance with local codes, if hard
wired. In the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in
he current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.
Remove the cover plate from the left side of the appliance by removing the two screws, as
Unscrew and remove power
cord.
the wiring to the junction block. Pl
ease make
sure the live wire goes into the "L", the
neutral wire into "N" and the ground wire into
"G".
and screws
.
Turn off the appliance completely and let cool before servicing. Only a ualified
technician
If it is necessary to hard wire this appliance, a ualified electrician must remove the cord connectio
n,
This appliance must be electrically connected and grounded in accordance with local codes, if hard
wired. In the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in
he current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.
Remove the cover plate from the left side of the appliance by removing the two screws, as
sure the live wire goes into the "L", the
11

MEDIA OPTIONS
MEDIA INSTALLATION
STEP 1: Unplug the unit and make sure
controls are switched off.
STEP 2: Unscrew 2 adjustable screws that
securing the front glass panel. (Always secure
the front glass before unscrewing the securing
screws, removal of the securing screws may
cause the front glass to fall out suddenly)
STEP 4: After finishing decoration, re-install
the front glass panel using the securing
screws removed in step 2.
adjustable screws
STEP 3: Remove the front glass panel to
decorate your fireplace. Pour the decorative
media into the tray. Feel free to use any
combination of fire glass media that you find
most appealing.
Birch log set
12
The media that come with this appliance are
Birch Log Set, “Clear glass”, Amber glass, one (1)
bag of Blac Vermiculite and one (1) bag of
White Vermiculite. Consumers may purchase
optional decorative media if they choose. See
dealer for more details.
Clear glass Amber glass Vermiculite

OPERATION
Plug the fireplace into a 15 Amp wall socket.
MANUAL OPERATION
Plug the fireplace into a 15 Amp wall socket.
1. Press to turn on and off the fireplace.
2. Press to adjust the flame’s brightness. There are 7 brightness levels (L5 L4 - L3
L2 L1 L0 L6).The indicator light turns off automatically leaving it not operated within
10 seconds.
3. Press to adjust the ember bed brightness. There are 12 brightness levels (D4 D5
D6 D7 D8 D9 DA DB D0 D1 D2 D3).
4. Press to set the turn-off time, 30min-1h-2h-3h-4h-5h-6h-7h-8h-t0. The indicator light
turns off automatically leaving it not operated within 10 seconds. The timing turns off
when is pressed.
5. Press to turn on and off the heater in its AUTO mode. The setting temperature
switch through 59℉- 61℉- 63℉- 64℉- 66℉- 68℉- 70℉- 72℉- 73℉- 75℉- 77℉- 79℉-
81℉- 83℉ - ℉ in Fahrenheit or 15℃ -16℃ -17℃ - 18℃ - 19℃ - 20℃ - 21℃ - 22℃ - 23℃
- 24℃ - 25℃ - 26℃ - 27℃ - 28℃ - ℃ in Celsius. The temperature setting mode will be
closed automatically if leaving not operated for 5 seconds.
6. When the heater is on, press the for 5 seconds to switch between Celsius and
Fahrenheit.
The Fireplace operates by using either the touch panel located on the upper left hand corner
or by remote control.
13

REMOTE CONTROL OPERATION
For remote to function make sure the fireplace is plugged in and the remote has batteries.
Important: When operating the remote make sure you point the remote to the center of the
fireplace. Each time you press the button, the buzzer inside the unit will beep once. It takes
some time for the receiver to respond to the transmitter. Do not PRESS the buttons more
than once within two seconds for correct operation.
Set the current time of the remote control
Press the to activate the remote control and press to set the time and date.
When one of the “Sun” “Mon” “ Tue” “Wed” “Thu” “Fri” “Sat” is flashing, press or to
set the day of the week, press to confirm day of the week and then enter hour setting.
Press or to set the hour, press to confirm the hour and then enter minute
setting. Press or to set the minute and press to confirm the minute and
finish time setting.
Press this Power button to turn on and off the fireplace.
Press this Timer button to set the time to turn off the fireplace.
The available settings range from 3 minutes to 8 hours. As
shown in the following: :3 - 1: - 1:3 - 2: - 2:3 - 3: -
3:3 - 4: - 4:3 - 5: - 5:3 - 6: - 6:3 - 7: - 7:3 - 8: .
Once you have set the timer, the icon will be displayed
on the LCD screen of the remote control. Press this button
again to cancel the timer setting and the icon disappears.
Press the HEATER button once, one setting of heater works,
75 W, indicating “H 1” on display; Press again, two settings of
heater work, 15 W, indicating “H 2” on display; Press for the
14

third time to turn on the AUTO mode, press or to set the temperature
and or to switch temperature unit between Celsius and Fahrenheit.
Press this button to adjust the speed of the flame. There are 3 options: High-
Medium- Low.
Press this button to turn on and off the ember bed light. When in ON position, the
display screen of the remote control shows AD 1, when the number “1” flashes, you
can set the color of the ember bed by or . There are 1 different ember bed
light colors (AD1-1 ). When in AD 11 status, the color of the ember bed light cycles
through 1 colors. Press “SET” to confirm the setting.
Press the Flame button to turn on and off the Flame. When in ON position, the LCD
screen of the remote control shows 6 6 6. Press or or to change
the brightness of each color flame.
7 Day Timer Function
Press once, 7 days from Monday to Sunday will display on the LCD screen of
the remote control, press within 5 seconds to enter 7 day timer function. When
“Sun” flashes, press or to select the day that you want to set, press to
confirm your setting. Then “ON” will be display on the LCD screen of the remote
control, at the same time, digital of time hour flashes, press or to set the
time to turn the fireplace on. After setting the startup time, “OFF” will be displayed on
the LCD screen and press or to set the shutdown time. When the
shutdown time’s set, “AUTO” will be displayed on the LCD screen of the remote
control and the digital of temperature flashes. At this time, you can set the
temperature by or . Now, you have finished setting of this function.
15

16
When the 7 day timer’s set, the icon will be displayed on the LCD screen of the
remote control. Press again to cancel the 7 da
will disappears.
NOTE: If the 7 day timing and the general timing are set at the same time, the
system will respond to an earlier shutdown time.
Press Refer button to check the settings of 7 day timer. Press or to see the
settings of the day of the week and or the settings of the startup and
shutdown time.
y timer and the icon

17
WIFI OPERATION
IN TALL Tuya mart life
There are 2 ways to install TuyaSmart;
1. Search for “TuyaSmart life” in the APP store on your phone, download and install.
2. Scan the QR code below with your mobile phone.
WIFI ETTING AND FIREPLACE OPERATION
1. Create an account and log in.
2. When you log in, touch “+” (FIG.1) to enter in FIG.2. Touch “others” on the left corner first
and then choose “Connector (Wi-fi)” to enter in FIG.3 to set your Wi-fi account and
password.
FIG.1 FIG. 2 FIG.3

1
FIG.4
3. Press (flame button) on the touch panel of the fireplace for more than 5 seconds
when the fireplace in standby mode. There will be 2 beeps come out from the fireplace
and the (flame button) will flash as well indicating that Wi-fi is in EZ mode. Then
please confirm to go next. (FIG.5)
4. The APP will scan (FIG.6) and add the fireplace to APP (FIG.7) automatically. Please
make sure the Wi-fi account and password you set are correct and Wi-fi signal is good.
5. Touch “Done” to finish Wi-fi setting.(FIG.7)
FIG.5 FIG.6 FIG.7

19
6. Now you are in the interface like FIG.7. You can operate the fireplace via Wi-fi.
FIG.7

20
Reference No. Description Quantity WM-BI-2428 VLR -BG - WiFi
1Top Panel 1
2Back Top Panel 1
3Circuit Board 1 10124129
4Blower & Heater Assembl 1 602082
5Fireplace Box 1 601097
6Canop Light 1 601139B
7Canop Light Bracket 1 10104010
9Signal Receiver 1 301506
10 Power Cord 1 10103007
11 Touch Panel 1 10124003
12 Flicker Assembl for Flame 1 3056504E
13 Flame LED Strip 1 601144
14 Tra LED Strip 1 601144
15 Flicker Assembl for Tra 1 3056503D
16 Tra Glass 1 10701200C
17 Side Bracket 1 10702150
18 Front Flat Glass 1 10701164
19 Remote 1 10101501
20 WiFi Card 1 212051
*Remote Control & WiFI Card are not shown in the exploded view
*Items ma not appear exactl as illustrated
R PLAC M NT PARTS