Amart Furniture JASON MK2 User manual

ASSEMBLY INSTRUCTION
ITEM CODE -
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Freecall 1800 351 084.
WARNING :
TOP BUNK AND ELEVATED BEDS
ARE DANGEROUS AND ARE NOT RECOMMENDED
FOR CHILDREN UNDER AGE OF 9
Falls from elevated beds can be fatal and deaths have
occurred where children have fallen from elevated beds.
This is relevant for all ages. The risk is greater for younger children.
The risk of injury or death from a fall from an elevated bed
compared to a non-elevated bed is :
10 x greater for 7-8 year olds
7 x greater for 9-10 year olds
3 x greater for 11-12 year olds
1 / 18 64972
64972
JASON MK2 DOUBLE BUNK BED
WARNING :
The upper bunk must be more than 2m from any ceiling fan.
Furniture

PRE-ASSEMBLY PREPARATION
2 / 18 64972
BEFORE YOU START....
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product.
2. Check and ensure that you have all required contents for complete assembly.
3. Always read the assembly instructions carefully before beginning assembly.
4. The packaging and contents can be a choking hazard, therefore keep out of reach
of small children at all items.
5. Do not over tighten the bolts as this may damage the thread.
ALLOW 120 MINUTES 4 PEOPLE REQUIRED
ADDITIONAL TOOLS REQUIRED
WARNING
To help prevent serious or fatal injuries from entanglement or falls :
.Use the correct size mattress as specified
.Upper surface of mattress must be at least 160mm below upper
edge of guard rails
.Follow all written instructions included with this bed
.Use guardrails on both sides of upper bunk
.Check the bunk bed periodically to ensure that the guardrails,
access device and other components are maintained in the
correct position and state of repair and that all connectors are
tight with nothing protruding more than 8mm
.Ensure the upper bunk is more than 2m from any ceiling fan
.Prohibit horseplay on or under bed
.Prohibit more than one person on the upper bunk
TOP BUNK AND ELEVATED
BEDS ARE DANGEROUS AND
ARE NOT RECOMMENDED
FOR CHILDREN UNDER THE
AGE OF 9.
DO NOT REMOVE THIS LABEL

3 / 18 64972
PARTS LIST
NO PART QTY. PICTURE PACKING CARTON .
1 SIDE FRAME - LEFT 1 UNIT BOX 1 / 6 B
2 SIDE FRAME - RIGHT 1 UNIT BOX 1 / 6 B
3 BOTTOM SIDE RAIL - FRONT 1 PC BOX 2 / 6 B
4 BOTTOM SIDE RAIL - BACK 1 PC BOX 2 / 6 B
5 TOP SIDE RAIL - FRONT 1 PC BOX 2 / 6 B
6 TOP SIDE RAIL - BACK 1 PC BOX 2 / 6 B
7 BOTTOM STORAGE - TOP & BOTTOM 2 PCS BOX 3 / 6 B
8 BOTTOM & TOP STORAGE PARTITION 5 PCS BOX 3 / 6 B
9 TOP & BOTTOM STORAGE BACK PANEL 2 PCS BOX 2 / 6 B
10 TOP STORAGE PANEL - TOP 1 PC BOX 3 / 6 B
11 TOP STORAGE PANEL - BOTTOM 1 PC BOX 3 / 6 B
12 TOP STORAGE BACK SUPPORT 3 PCS BOX 3 / 6 B
13 TOP STORAGE PANEL - SIDE LONG 1 PC BOX 3 / 6 C
14 LADDER BACK PANEL 1 PC BOX 4 / 6 A
15 LADDER PANEL - FRONT TOP 1 PC BOX 4 / 6 A
16 LADER PANEL - FRONT CENTER 1 PC BOX 4 / 6 A
17 LADDER PANEL - FRONT BOTTOM 1 PC BOX 4 / 6 A
18 LADDER INNER PANEL - TOP & CENTER 2 PCS BOX 4 / 6 A
19 LADDER INNER PANEL - BOTTOM 1 PC BOX 4 / 6 A
20 LADDER HORIZONTAL PANEL - A 1 PC BOX 4 / 6 A
21 LADDER HORIZONTAL PANEL - B 1 PC BOX 4 / 6 A
22 LADDER HORIZONTAL PANEL - C 1 PC BOX 4 / 6 A
23 LADDER HORIZONTAL PANEL - D 1 PC BOX 4 / 6 A
24 METAL SAFETY RAIL - A 1 PC BOX 6 / 6 C
25 METAL SAFETY RAIL - B 1 PC BOX 6 / 6 C
26 METAL SAFETY RAIL - C 1 PC BOX 6 / 6 C
27 TOP WOOD SLAT (15pcs/set) - 30 SCREW HOLE
- 18 mm x 59mm x 920mm 1 SET BOX 5 / 6 B
28 BOTTOM WOOD SLAT (15pcs/set) - 10 SCREW HOLE
- 18mm x 59mm x 920mm 1 SET BOX 5 / 6 B

4 / 18 64972
Mini Fix Bold
Wood Dowel
M8x30mm JCBC Bolt M6x60mm
& Barrel Nut JCBC-W Screw
M6x50mm
JCBC Bolt M6x30mm CSK Chipboard Screw
#4 x 30mm Pan Head Screw
#3.5 x 16mm L-Bracket
14 x 20mm
Ax 93 pcs Bx 12 pcs Cx 33 pcs Dx 63 pcs
Ex 8 pcs Fx 40 pcs Gx 36 pcs Hx 16 pc
Allen Key - M6
CSK Chipboard Screw
#3.5 x 16mm
Ix 32 pcs Kx 1 pc
PART A
PART B
PART C
Wood Dowel
M8x30mm
Ax 56 pcs
JCBC Bolt M6x60mm
& Barrel Nut
Cx 23 pcs
JCBC-W Screw
M6x50mm
Dx 34 pcs
Mini Fix Bolt
Bx 12 pcs L-Bracket
14 x 20mm CSK Chipboard Screw
#3.5 x 16mm
Ix 32 pcsHx 16 pcs
Wood Dowel
M8x30mm
Ax 32 pcs
JCBC Bolt M6x60mm
& Barrel Nut
Cx 10 pcs
JCBC-W Screw
M6x50mm
Dx 22 pcs
Pan Head Screw
#3.5 x 16mm
Gx 36 pcs
Wood Dowel
M8x30mm
Ax 5 pcs
JCBC-W Screw
M6x50mm
Dx 7 pcs
JCBC Bolt
M6x30mm
Ex 8 pcs
CSK Chipboard Screw
#4 x 30mm
Fx 40 pcs
JCBC Bolt M6x40mm
Jx 2 pcs
JCBC Bolt
M6x40mm
Jx 2 pcs

5 / 18 64972
2
5
3
6
1
17
16
15
20
22
18
13
23
19
14
9
10
1
9
9
14
6
5
2
13
4
28
8
8
8
11
27
18
12
12
12
23
21
20 10
7
8
8
8
8
8
7
28
3
FRONT VIEW
BACK VIEW
24
24
21
22 11 27
25
26

6 / 18 64972
PART B PART A PART C
PART B
PART A
PART C

ASSEMBLY FOR PART A
7 / 18 64972
STEP 1 :
STEP 2 :
Wood Dowel
M8x30mm
Ax 10 pcs
JCBC-W Screw
M7x50mm
Dx 4 pcs
A
D
D
D
D
A
A
A
A
19
17
23
JCBC-W Screw
M7x50mm
Wood Dowel
M8x30mm
Ax 10 pcs
Dx 4 pcs
JCBC Bolt M6x60mm
& Barrel Nut
Cx 4 pcs
C
C
A
D
A
A
A
D
A
22
18
19
16
17
23
Attach Ladder Panel(front bottom) 17 and Ladder Inner panel(bottom) 19 to
the Ladder Horizontal Panel(D) 23 with hardware as shown.
Attach Ladder Horizontal Panel(C) 22 to the
Ladder Panel(front bottom) 17 and Ladder Inner
panel(bottom) 19 follow by Ladder Panel(front
center) 16 and Ladder Inner Panel(top/center) 18
with hardware as shown.

8 / 18 64972
STEP 3 :
STEP 4 :
Wood Dowel
M8x30mm
Ax 2 pcs
JCBC Bolt M6x60mm
& Barrel Nut
Cx 2 pcs
JCBC-W Screw
M7x50mm
Dx 10 pcs
14
D
D
D
D
C
20
A
D
Attach Ladder Back Panel 14 to the Ladder
Horizontal Panel(B,C,D) 21 , 22 , 23 . After that
attach Ladder Horizontal Panel(A) 20 to the
parts as shown with hardware as shown.
21
22
23
18
15
18
16
21
18
15
A
A
A
C
C
D
D
A
A
Attach Ladder Horizontal Panel(B) 21 to the
Ladder Panel(front center) 16 and Ladder Inner
Panel(top/center) 18 follow by Ladder
Panel(front top) 15 and Ladder Inner
Panel(top/center) 18 with hardware as shown.
Wood Dowel
M8x30mm
Ax 10 pcs
JCBC Bolt M6x60mm
& Barrel Nut
Cx 4 pcs
JCBC-W Screw
M7x50mm
Dx 4 pcs

9 / 18 64972
ASSEMBLY FOR PART B
Remove all packing part item by lossing all screws as
shown.
Take out Side Frame(left) 1 and Side Frame(right) 2
as shown.
1
2
STEP 1 :
STEP 2 :

10 / 18 64972
UP
STEP 3 :
Wood Dowel
M8x30mm
Ax 8 pcs
STEP 4 :
A
4
3
Fix wood dowel A to the Bottom Side
Rail(front) 3 and Bottom Side Rail(back) 4 .
JCBC Bolt M6x60mm
& Barrel Nut
Cx 8 pcs
1
2
4
3
C
C
NOTE ;
AT THIS STEP, PLEASE DO NOT TIGHTEN THE BOLTS YET.
Attach Bottom Side Rail(front) 3 and Bottom Side Rail(back) 4
to the Side Frame(left) 1 and Side Frame(right) 2 .

11 / 18 64972
STEP 5 :
STEP 6 :
Wood Dowel
M8x30mm
Ax 16 pcs
JCBC-W Screw
M7x50mm
Dx 8 pcs
7
78
8
D
D
A
A
D
D
A
ASSEMBLE ALL BOTTOM STROGE PARTS AS SHOWN FIRST.
Attach Bottom Storage(top/bottom) 7 to Storage
Partition(top/bottom) 8 .
NOTE ;
AT THIS STEP, PLEASE DO NOT TIGHTEN THE BOLTS YET.
Fix Bottom Storage to the Side Frame(left) 1 and Side Frame(right) 2 .
JCBC-W Screw
M7x50mm
Dx 8 pcs
D
1
2
4
8
8
7
7

12 / 18 64972
STEP 7 :
STEP 8 :
6
5
AWood Dowel
M8x30mm
Ax 8 pcs
Fix wood dowel A to the Top Side Rail(front) 5 and
Top Side Rail(back) 6 .
Attach Top Side Rail(front) 5 and Top Side Rail(back) 6
to the Side Frame(left) 1 and Side Frame(right) 2 . After
that tighten all bolts.
JCBC Bolt M6x60mm
& Barrel Nut
Cx 12 pcs
6
5
1
2
C
C

13 / 18 64972
STEP 9 :
STEP 10 :
Mini Fix Bolt
Bx 6 pcs
BBB
12 12 12
6
21
Attach Top Storage Back Support 12 to the
Top Side Rail(back) 6 with hardware as
shown.
Remarks ;
Minifix hole for Top Storage Back
Support 12 can be in either side.
Left Right
2
1
12 12 12
AA
D
DB
B
B
A
11
Wood Dowel
M8x30mm
Ax 6 pcs
Mini Fix Bolt
Bx 6 pcs
JCBC-W Screw
M7x50mm
Dx 4 pcs
L-Bracket
14 x 20mm
Hx 12 pcs
CSK Chipboard Screw
#3.5 x 16mm
Ix 24 pcs
Fix Top Storage(bottom) 11 to the Side Frame(left/right) 1 2
and Top Storage Back Support 12 .
Remarks;
Please fix L-Brackets on support, bracket can fix at both side.
H
I

ASSEMBLY FOR PART C
14 / 18 64972
STEP 1 :
STEP 11 :
Wood Dowel
M8x30mm
Ax 12 pcs
JCBC-W Screw
M7x50mm
Dx 12 pcs
Fix Top Storage Partition 8 to the Top Storage Panel(bottom) 11 .
After that fix Top Storage Panel(top) 10 as shown.
Wood Dowel
M8x30mm
Ax 8 pcs
JCBC-W Screw
M6x50mm
Dx 2 pcs
I
H
D
A
2
A
C
A
D
DC
Attach ladder box to the Side Frame(right) 2 and fix with
hardware as shown. After that tighten all bolts.
A
JCBC Bolt M6x60mm
& Barrel Nut
Cx 3 pcs
D
A
A
D
10
888
11

15 / 18 64972
STEP 2 :
STEP 3 :
Fix Top Storage Panel(side long) 13 to the Top Storage Panel(top) 10
and ladder box with hardware as shown.
9
9
G
G
Attach Top Storage Back Panel 9 and
Bottom Storage Back Panel 9 to the
bunk bed as shown.
Pan Head Screw
#3.5 x 16mm
Gx 36 pcs
Wood Dowel
M8x30mm
Ax 3 pcs
JCBC-W Screw
M7x50mm
Dx 7 pcs
D
A
D
A
DA
13

16 / 18 64972
F
4
3
6
5
28
27
F
CSK Chipboard Screw
#4 x 30mm
Fx 40 pcs
Attach Bottom Wood Slat 28 with 10nos of
screw holes to Bottom Side Rail(front) 3
and Bottom Side Rail(back) 4 .
Attach Upper Wood Slat 27 with 30nos of screw holes to Top Side Rail(front) 5
and Top Side Rail(back) 6 .
STEP 5 :
24
E
E
E
E
Attach Metal Safety Rail 24 , 25 and 26 to the ladder
box as shown.
STEP 4 :
JCBC Bolt
M6x40mm
Jx 2 pcs
E
25
26
Ex 8 pcs
JCBC Bolt
M6x30mm
J

17 / 18 64972
ASSEMBLY IS COMPLETE

18 / 18 64972
Product Care for Hi-Gloss Items
Hi-gloss lacquered furniture is more sensitive to marks and scratching then some other furniture
products. It is important to exercise caution and care to maximise the life and beauty of
this product.
Following the below simple guidelines when using your hi-gloss product will protect your
investment for years to come.
.Dust frequently with a clean damp lint-free cloth. This will help remove
abrasive build up which can damage a finish over time.
.Do not place hot objects on any furniture surface. Always use a hot plate or
placement. Laminate and lacquer finishes on table tops provide added scratch
and heat resistance to our furniture, but they can still be damaged without
proper care.
.Avoid exposing your furniture to strong sunlight, heat outlet, open windows or
dampness. Prolonged exposure to direct sunlight can fade the finish of your
furniture, while extreme temperature and humidity changes can cause
cracking or splitting.
.Do not expose your furniture to any liquids. Never allow water to sit on your
furniture. Alcohol, nail polish and perfume are also dangerous as they will
dissolve the lacquer finish on contact and may require professional repairs.
.Do not allow plastic to come in direct contact with your furniture. Chemicals in
the plastic of placements etc may soften and mark the finish if left in contact
with the furniture for a period of time.
.Avoid placing sharp or rough objects on the surface of your furniture. These
may scratch the surface of the product.
.When moving your furniture, do not drag it across the floor. This may damage
the product. Instead use two (2) people to lift carefully from either end.