Amart Furniture AINSLEY 69243 User manual

1 69243
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084
ASSEMBLY INSTRUCTION
AINSLEY BE D S I D E
ITEM CODE 69243
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084

2 69243
PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the product
2. Take care when lifting. Product should be assembled as near as possible to the point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads

3 69243
PARTS L I S T
NO
D E S CR I P T I O N Q t y
1 C H E S T 1
2 L E G 4
a.
B o l t S c r e w
M6x40
4 p c
s
b.
Allen key
M4
1 p c

4 69243
ITEMS R E Q U I R E D

Slowly pull
out Drawer of
C h e
s
t (A) halfway,
push down
i n
s
i d e p l a
s
t i c
and
t h e n pull
Drawer out as shown
b e l o w

5 69243
ITEMS R E Q U I R E D

A tt a c h legs
(2) to the chest (1)
using bo l t
screws (a).
T i g h t e n w i t h Allen K e y
(b).
Sli d e
Drawer
i n t o
the chest as shown
b e l o w .
a.
B o l t S c r e w
M6x40
4 p c
s
b. Allen key M4
1pc

6 69243
SAFETY BRACKETS INSTRUCTIONS
1. Attach one bracket to the wall, with the long screws as shown. Make
sure to attach the bracket into a stud. If mounting onto brick or
masonry, you will need to acquire wall anchors.
2. Attach a bracket to the furniture frame under the top with the short
screws provided.
3. Move the furniture into its final position. Thread a strap through the
bracket as shown in the illustration, tighten strap until snug. Do not
over tighten.
4. Make sure the bracket is firmly attached to the wallboard and
furniture, and the strap is snug.

7 69243
ASSEMBLY IS COMPLETE

Care label for timber items
 A multi-step finish is applied to all our furniture, but all wood comes from
nature. Because of this, there will be natural variations in surface texture
and grain like knots, mineral streaks and sap runs that may affect the
finish. These differences in character are not defects, but distinctions that
make each piece of furniture unique.
 Our furniture is built to last. Following these steps for basic care should
protect your investment for years to come.
 Dust frequently with a clean damp lint-free cloth. This will help remove
abrasive build up which can damage a finish over time.
 Do not place hot objects on any furniture surface. Always use a hot plate
or placemat. Laminate and lacquer finishes on table tops provide added
scratch and heat resistance to our furniture, but they can still be
damaged without proper care.
 Avoid exposing your furniture to strong sunlight, heat outlet, open
windows or dampness. Prolonged exposure to direct sunlight can fade
the finish of your furniture, while extreme temperature and humidity
changes can cause cracking or splitting.
 Do not expose your furniture to any liquids. Never allow water to sit on
your furniture. Alcohol, nail polish and perfume are also dangerous as
they will dissolve the lacquer finish on contact and may require
professional repairs.
 Do not allow plastic to come in direct contact with your furniture.
Chemicals in the plastic of placemats etc may soften and mark the finish
if left in contact with the furniture for a period of time.