Amart Furniture MARSEILLE 75915 User manual

Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084
ASSEMBLY INSTRUCTION
MARSEILLE KING BED
ITEM CODE 75915
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please
phone Amart Furniture , Customer Service Free call 1800 351 084
1ITEM CODE 75915

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2.Take care when lifting. Product should be assembled as near as possible to
the point of use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instructions carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over tighten the screws and bolts as this may damage the threads
2ITEM CODE 75915
ALLOW90MINITES 2PEOPLEREQUIRED
TOOLSREQUIRED
12
11
10
9
8
765
4
3
2
1
We recommend using a
screwdriver to put this item
together. However if you choose
to use a power drill it must be
used on LOW SPEED (LOW
TORQUE) as too much pressure
could damage the product

3ITEM CODE 75915
1 HEADBOARD
2 FOOTBOARD
3 SIDERAIL
4 SIDERAIL
5 SLATS
6 RUNNER BRACE
7 RUNNER BRACE
8 COVER BOARD
9 CENTRE RAIL
10 SUPPORT LEG
11 SUPPORT LEG
12 DRAWER FRONT
13 DRAWER LEFT SIDE
14 DRAWER RIGHT SIDE
15 DRAWER BACK
16 DRAWER BASE
17 DRAWER SUPPORT BAR
PARTS LIST

ITEM CODE 75915
4
1.
X 2
•Attach drawer sides (13)(14) to drawer front (12) and drawer
back (15) with screws (G).
•Put drawer base (16) into groove of the boards (13)(14)
and (12).

ITEM CODE 75915
5
2.
•Attach drawer support bar (17) to the middle of the
drawer base (16) with screws (G).
•Fix drawer base(16) to drawer front (12) and back
(15) with screws (F).

6 ITEM CODE 75915
3.
•Attach runner brace (6) to runner brace (7) with screws (G).
•Take care to keep the four brace pieces level.

7 ITEM CODE 75915
4.
•Attach siderail (3)(4) to runner brace frame with flat washer
(B) and bolt (A) .
•Tighten with allen key (D)

8ITEM CODE 75915
5.
•Attach footboard (2) to siderails (3)(4) with flat washer (B),
lock washer (C) and bolt (A) .
•Tighten with allen key (D)

9ITEM CODE 75915
6.
•Attach headboard (1) to siderails (3)(4) with flat washer (B),
lock washer (C) and bolt (A).
•Tighten with allen key (D)

10 ITEM CODE 75915
7.
•Attach cover board (8) to drawer brace (6)(7).

11 ITEM CODE 75915
8.
•Fix cover board (8) to drawer brace (6) (7) with screws (E)

12 ITEM CODE 75915
9.
•Attach support legs (10)(11) to centre rail (9) with screws (G)
•Pay attention to the direction of support leg (11)
•Attach centre rail (9) and foot (11) to headboard (1), footboard (2)
and runner brace frame with flat washer (B) and bolt (A).
•Tighten with allen key (D)

13 ITEM CODE 75915
10.•Push the runner part (a) on the brace board so that they are
closely connected with part (b). Mind your fingers!!!
•Extend the runners (d) on the drawer sides (12)(13) and
insert into the brace board runners (a) and (b).
•Push both ends of the drawer front (12) and slowly push the
drawer into the bed. Note that the drawer front (12) should
end up flush with the siderail (3)/(4)
•Install another drawer in the same way

H . M 4X 30 MM
26 PCS
•Attach slats (5) to siderails (3)(4) using screws (H).
•Use Screwdriver or Power Drill on Low Speed.
14 ITEM CODE 75915
11.

15 ITEM CODE 75915
ASSEMBLY IS COMPLETE
CAUTION
Always Lift Your Bed When Moving /Relocating -
Do Not Drag. Dragging Can Cause The Centre
Support Legs To Bend/Break.

16 ITEM CODE 75915
Care and maintenance
•A multi-step finish is applied to all our furniture, but all wood comes
from nature. Because of this, there will be natural
variations in surface texture and grain like knots, mineral streaks and
sap runs that may affect the finish. These differences in character are
not defects, but distinctions that make each piece of furniture unique.
•Our furniture is built to last. Following these steps for basic care
should protect your investment for years to come.
•Dust frequently with a clean damp lint-free cloth. This will help
remove abrasive build up which can damage a finish over time.
•Do not place hot objects on any furniture surface. Always use a hot
plate or placemat. Laminate and lacquer finishes on table tops provide
added scratch and heat resistance to our furniture, but they can still
be damaged without proper care.
•Avoid exposing your furniture to strong sunlight, heat outlet, open
windows or dampness. Prolonged exposure to direct sunlightcan fade
the finish of your furniture, while extreme temperature and humidity
changes can cause cracking or splitting.
•Do not expose your furniture to any liquids. Never allow water to sit
on your furniture. Alcohol, nail polish and perfume are also dangerous
as they will dissolve the lacquer finish on contact and may require
professional repairs.
•Do not allow plastic to come in direct contact with your furniture.
Chemicals in the plastic of placemats etc may soften and markthe
finish if left in contact with the furniture for a period of time.