Amart Furniture 62056 User manual

Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084
ASSEMBLY INSTRUCTION
PROMENADE LAMP TABLE
ITEM CODE 62056
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please
phone Amart Furniture, Customer Service Free call 1800 351
084
1ITEM CODE 62056

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when lifting. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instructions carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over tighten the screws and bolts as this may damage the threads
2 ITEM CODE 62056
ALLOW 20 MINITES 2 PEOPLE REQUIRED
TOOLS REQUIRED
12
11
10
9
8
765
4
3
2
1

3 ITEM CODE 62056
PARTS LIST
1 GLASS TABLE TOP
2 X-LEG WITH ADJUSTABLE FEET
3 V-LEG WITH ADJUSTABLE FEET

ITEM CODE 62056
•Insert the dowel on the V-leg(3) into the X-leg(2).
•Attache the X-leg (2)&V-leg(3) using bolt(D)、lock
washer(F) and flat washer (E).
•Tighten with allen key(G).
4

ITEM CODE 620565
•Attach the two V-leg with the connection(H) using
screw (I).
•Use Screwdriver or Power Drill on Low Speed.

ITEM CODE 62056
•Peel film from the silicone plate (A) and adhere the sticky
side of the silicone plate to the flat side of the aluminium
plate (B)
•Put the bolt (C)into the aluminium plate(B).
•Then attach the aluminium plate(B) and the X-leg(2) &V-
leg (3)with the bolt(C)
6
!
NOTE: Peel and adhere the
sticky side of the silicone
plate (A) to the flat side of
the aluminium plate (B)

ITEM CODE 62056
•Put the glass top on the legs.
•Rotate the bottom adjustable feet to make the table
level.
7

ITEM CODE 620568
!
STEP 1: Fix bracket to lamp table leg using screws M3.5*14MM .
NOTE –This product must be fixed to a wall. Please ensure the correct wall fixings
are used. Failure to do so may result in personal injury or cause property damage if
the product topples over. As wall materials vary greatly, the fastener required to fix
this product to a wall is not included. If unsure, consult your local hardware store for
advise on wall fixings which would be suitable for your situation.

ITEM CODE 620569
STEP 2: Put plastic string into bracket .

10 ITEM CODE 62056
STEP 3: Fix bracket onto the ground using screws M4*30MM.
Join ground and the lamp table leg with plastic sting .

11 ITEM CODE 62056
!
SAFETY BRACKETS INSTRUCTIONS
1.Attach a bracket to the ground with the long screws provided.
2.Attach a bracket to the lamp table leg with the short screws
provided.
3.Move the furniture into its final position. Thread a strap through
the bracket as shown in the illustration, tighten strap until snug.
Do not over tighten.
4.Make sure the bracket is firmly attached to the ground and
furniture, and the strap is snug.

8ITEM CODE 62056
ASSEMBLY IS COMPLETE

9ITEM CODE 62056
PRODUCT CARE:
If the glass is chipped or broken, stop using the product and consult place
of purchase
WARNING:
• Do not place very hot or cold items on the glass surface unless adequately
thick table mats are used to prevent such items coming in contact with the
glass
• Do not sit or stand upon the glass surface
• Do not use the glass as a chopping surface
• Do not strike the glass with hard or pointed items
• When cleaning the glass panels use a damp cloth or leather with washing
up liquid or soft soap if necessary. Do not use washing powders or any
other substances containing abrasives since these may scratch the glass
Our furniture is built to last. Following these steps for basic care should
protect your investment for years to come
• Dust frequently with a clean damp lint-free cloth. This will help remove
abrasive build up which can damage a finish over time
• Avoid exposing your furniture to strong sunlight, heat outlet, open
windows or dampness. Prolonged exposure to direct sunlight can fade the
finish of your furniture, while extreme temperature and humidity changes
can cause cracking or splitting
• Do not allow plastic to come in direct contact with your furniture.
Chemicals in the plastic of placemats etc. may soften and mark the
finish if left in contact with the furniture for a period of time