Amart Furniture LAYTON 61357 User manual

61357
LAYTON DESK GY/WT
61357
120CM
48CM
76CM
1-9

PRE-ASSEMBLY PREPARATION
BEFORE YOU START:
2
ALLOW 20 MINUTES PEOPLE REQUIRED
ADDITIONAL TOOLS REQUIRED
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the product
2. Take care when lifting. Product should be assembled as near as possible to the point of use
3 . E n s u r e t h a t y o u h a v e a l l r e q u i r e d c o n t e n t s f o r c o m p l e t e a s s e m b l y
4 . A l w a y s re a d t h e a s s e m b l y i n s t r u c t i o n s c a r e f u l l y b e f o r e b e g i n n i n g a s s e m b l y.
5 . K e e p a l l h a r d w a r e p a r t s a n d p a c k a g i n g o u t o f r e a c h o f s m a l l c h i l d r e n .
6. Do not over tighten the screws and bolts as this may damage the threads
2-9 61357

PARTS LIST
Top Panel
Bottom Panel
Left Side Panel
Side Panel
Back Panel
Drawer Left Panel
Drawer Right Panel
Drawer Back Panel
Bottom Drawer Panel
Metal Frame
Front Drawer Panel
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
ST4X25mm
2pcs 2pcs 2pcs
Screw
Wall Nut Metal
26pcs
B1
M6X25mm
6pcs
B2
M6X12mm
20pcs
C
ST3.5X14mm
16pcs
A
FG
8X30mm
12pcs 1pc
E1
2pcs
4pcs
H
D
M4X18mm
2pcs
E
E2
I J K
Bolt Bolt Bolt
Screw
Bolt
Wood Dowel
Drawer Runner
Plastic Tack
Handle
2
5
1
4
4
3
6
10
9
7
8
11
11
11
11
Metal Tube
12
12
3-9 61357

STEP 1
STEP 2
STEP 3
Assemble metal tube (12) to bottom panel (2)using bolt (B1).
B1
2
B2
2
HH
H
H
E1 E2
E1 E2
C
C
C
C
E1
E1
44
C
C
12
12
11
11
1111
Assemble metal frame (11) to bottom panel (2)using bolt (B2),then insert plastic tack (H)
to metal frame (11) .
Assemble drawer runner (E1) to side panel (4) using screw (C).
4-9 61357

STEP 4
STEP 5
STEP 6
A
5
4
4
A
A
F
A
3
4
2
4
5
F
A
1
3
4
54
A
Assemble back panel (5) to side panel (4) using bolt (A).
Assemble back panel (5),left side panel (3),side panel (4) to bottom panel (2) using bolt (A)
and wood dowel (F). metal tube (12) to bottom panel (2)using bolt (B1).
Assemble back panel (5),left side panel (3),side panel (4) to top panel (1) using bolt (A)
and wood dowel (F).
5-9 61357

STEP 7
STEP 8
STEP 9
7
8
9
A
A
A
D
10
D
G
8
7
6
6A
C
C
E2
7
8
C
Assemble drawer back panel (9) to drawer left panel (7) and drawer right panel (8) using
bolt (A).
Assemble handle (G)to front drawer panel ( 6) using bolt (D),then insert bottom
drawer panel as instruction showing.Assemble front drawer panel (6) to drawer
left panel (7) and drawer right panel ( 8).
Assemble drawer runner ( E2)to drawer left panel (7)and drawer right panel ( 8)
using screw (C).
6-9 61357

STEP 10
STEP 11
Assembly is complete.
6
1
Insert drawer (6) then assemble metal (K) to top panel ( 1) using screw (C).
7-9 61357
STEP 12
K
J
I
C
C
K
Knock in wall nut (J) on the wall,then connect metal (K) and wall nut (J) using screw (I).
Fix the desk to the wall.

SAFETY BRACKETS INSTRUCTIONS
HARDWARE
Screw x 1
Wall Nut x 1
Metal x 1
Wall
Back Side
Attach one Mounting Plate to the wall with the Large Screws. Make sure to attach the
Mounting Plate into a stud. If mounting into brick or masonry you will need to acquire
wall anchors.
Attach the second Mounting Plate to the furniture frame with the Short Screws.
Move the furniture to its final position. Thread a Wall Strap through the both Mounting
Plates and tighten until snug. Do not over tighten.
Make sure that the Mounting Plates are firmly attached to the wall and furniture and
that the Wall Strap is snug.
1.
2.
3.
4.
8-9 61357

9-9 61357
CARE AND MAINTENANCE
A multi-step finish is applied to all of our furniture, but all wood comes from nature. Because
of this, there will be natural variations in surface texture and grain like knots, mineral streaks
and sap runs that may affect the finish. These differences in characterare not defects, but
distinctions that make each piece of furniture unique.
Following these steps for basic care should protect your investment for years to come..
Dust frequently with a clean damp lint-free cloth. This will help remove abrasive build up
which can damage a finish over time.
Do not place hot objects on any furniture surface. Always use a hot plate or placemat.
Laminate and lacquer finishes on tabletops provide added scratch and heat resistance to our
furniture, but they can still be damaged without proper care
Avoid exposing your furniture to strong sunlight, heat outlet, open windows or dampness.
Prolonged exposure to direct sunlight can fade the finish of your furniture, while extreme
temperature and humidity changes can cause cracking or splitting
Do not expose your furniture to any liquids. Never allow water to sit on your furniture. Alcohol,
nail polish and perfume are also dangerous as they will dissolve the lacquer finish on contact
and may require professional repairs
Do not allow plastic to come in direct contact with your furniture. Chemicals in the plastic of
placemats etc. may soften and mark the finish if left in contact with the furniture for a period
of time.