Amart Furniture ELSA 55029 User manual

495mm
525mm
790mm
ASSEMBLY INSTRUCTION
ELSA DINING CHAIR
ITEM CODE 55029
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture Ewing Road, Customer Service Free call 1800 351 084
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture Ewing Road, Customer Service Free call 1800 351 084
5502955029 1 29012020

55029 2
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when lifting. Product should be assembled as near as possible to the point of use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instructions carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over tighten the screws and bolts as this may damage the threads
PRE-ASSEMBLY PREPARATION
55029 2 29012020
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when lifting. Product should be assembled as near as possible to the point of use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instructions carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over tighten the screws and bolts as this may damage the threads
PRE-ASSEMBLY PREPARATION

4
41L
1R
2
3
5
5
55029 3 29012020
PARTS LIST
4pcs
E. Allen Key M4
1pc
D. FH Screw #8 x 25mm
16pcs
LEG (LEFT / RIGHT )
1
2 TOP REST
3
1PC
4
1PC
CORNER BLOCK (LEFT / RIGHT) 2PCS
2PCS
CUSHION SEAT
4pcs
C. JCBC W M7 x 40mm
1pc
A. JCBC Bolt M6 x 25mm +
S/W M6 + F/W M6 x 13mm B. JCBC Bolt M6 x 55mm + S/W M6 + F/W M6 x 13mm
F. Protective Disc 22mm
4pcs
5CORNER BLOCK (FRONT / BACK) 2PCS

1L 1R
3
B
E
STEP 1 :
STEP 2 :
55029 4 29012020
Crossover the Left Side Frame (1L) into Right
Side Frame (1R) .
Attach the Seat Cushion (3) to the Frames using Bolts (B)
with a Spring Washer and Flat Washer. Tighten using
Allen Key (E).

2
E
A
2
1
C
E
STEP 3 :
STEP 4 :
55029 5 29012020
Attach the Top Rest (2) to the Frames using Bolts (A) with a
Spring Washer and Flat Washer. Tighten using Allen Key (E).
Secure the Seat Cushion (3) to the center of the frames
using JCBC Bolt (C). Tighten using Allen Key (E) .

D
5
4
5
4
5
4
F
STEP 5 :
55029 6 29012020
Fix the Corner Block (4) and (5) to the Frames using Screw
(D). Tighten with a Screw Driver (not provided).
STEP 6 : Paste Protective Disc (F) at a bottom leg as shown.

ASSEMBLY IS COMPLETE
Important note-
Before finally tightening the bolts,
place the assembled chair upright
on a level surface and sit carefully
on the chair to ensure the chair
legs are aligned and level. Then
tighten all bolts and your chair
is ready for use.
55029 7 29012020

IMPORTANT: CARE GUIDE FOR YOUR FABRIC CHAIR
Congratulations! You have just purchased a quality product from
Amart Furniture, Australia’s largest discount furniture retail store. Please
read on for important care information regarding your purchase…
Regular Care:
Always protect your product from direct sunlight, direct heat, and weather.
Vacuum regularly using a low suction setting.
Cleaning:
Do not remove cushion covers for separate cleaning even though they may
have zips. Do not wash. Do not dry clean. Do not use dishwashing or laundry
detergents or solvents. Do not wet the internal filling.
It is recommended that cleaning be done with a hot water extraction
machine only by a professional cleaner.
Spot cleaning:
Do not rub or scrub. Do not spot clean with any solvent.
Treat spills and stains as soon as possible.
Gently scrape any soil or mop and liquid from the surface of the fabric.
Apply proprietary cleaning agents to the residue of the spill, strictly according
to the manufacturer’s instructions.
Do not saturate the fabric or interior filling with water or other cleaning
liquids.
Important note:
Apply only water-based soil resistant (fabric protection) treatments.
Do not aerosol fabric protection products.
Clean timber legs with a clean, soft cloth dampened with water.