Amazon B005PJJ89U User manual

B005PJJ89U
▼▲
SET

2
▼▲
SET
Set button
Up/Down buttons
LCD display
Flashlight power button
Nozzle
A
B
C
D
E
E
C
B
AD
Turns gauge on/sets choices
Increases/decreases setting options
Displays selections/readings
Turns LED ashlight on/off
Releases air/reads tire pressure

Instruction Manual
AmazonBasics Programmable Digital Tire Gauge
3
Features
• Program your vehicle’s tire pressure volume
• Fine tune tire pressure with air-bleed function
• Reach awkward angles with the swivel head
• Easy-to-read, extra large backlight display
• Built-in white LED flashlight on tip

4
To use:
Measuring pressure
1. Press Set. The display lights and “0.0” appears. The default
unit of measure is PSI.
2. Remove the cap from your tire valve.
3. Push and hold the nozzle on the gauge against the valve stem
until the pressure reading is displayed and locked.
4. Remove the gauge from the valve stem. The pressure
reading stays on the display for 10 seconds. The display
returns to the “0.0” reading, then turns off after 10 seconds.

5
Over range error
If your tire pressure is more than 99.5psi/ 6.90bar,
the display will show an “E.”
Setting a target for tire pressure level
Note: The target numbers you set are reminders of your vehicle manufacturer’s
suggested tire pressure levels. They cannot be used to test for or indicate
actual pressure in tires.
To find your vehicle manufacturer’s suggested tire pressure levels see
your vehicle owner’s manual.
1. Press Set. The display lights and “0.0” appears.

6
2. Press Set again and hold for 3 seconds. The unit “PSI” or
“BAR” appears and blinks. Press or to switch between
PSI and BAR. Then, press Set to conrm your selection.
The icon indicating front or rear tire lights and blinks.
3. Press or to choose front or rear tire, then press Set to
conrm.

7
4. Press or to change the target number you want, then
press Set to conrm. The icon for the next tire is displayed.
5. Press or to to select your target number, then press Set
to conrm.

8
6. Your target numbers for both tires light for about 2 seconds,
then the display returns to “0.0”.
Measuring pressure with a preset target
1. Press Set. The display lights and “0.0” appears.

9
2. Pressor to choose between the front and rear tires.
3. Push and hold the nozzle on the gauge against the valve
stem until the pressure reading is displayed and locked.
4. Remove the gauge from the valve stem. The current
pressure reading appears on the top of the display and
your target reading appears on the bottom for 10 seconds.

5. When the display returns to “0.0”, repeat steps for the
other tires.
6. After your nal reading the display returns to “0.0” and
turns off after 10 seconds.
Using the white LED ashlight
Press and hold the power button to turn on the light.
Release the power button to turn off the light.
Low battery warning:
When the batteries are nearly expended the panel will display
“Lo.”
10

Made in China
© 2011 Amazon.com, Inc. or its afliates. All Rights reserved. Amazon and the AmazonBasics
logo are trademarks of Amazon.com, Inc. or its afliates. RoHS
11
Replacing the Batteries:
1. Remove the battery door on the back using a Phillips head
screwdriver to remove the black screw.
2. Replace old batteries with two CR2032 batteries (or
equivalent) matching +/- polarity as marked.
3. Replace the cover and tighten the screw.
BATTERY WARNING STATEMENT
• Keep batteries out of the reach of children.
• Insert the batteries in the proper direction as indicated by positive (+) and negative (-) markings in battery
compartment.
• Do not mix old and new batteries or batteries of different types (for example, carbon and alkaline batteries).
• Always remove old, weak, or worn-out batteries promptly and recycle or dispose of them in accordance with
Local and National Disposal Regulations.
• If a battery leaks, remove all batteries and recycle or dispose of them in accordance with battery
manufacturer's instructions and Local and National Disposal Regulations. Before inserting new batteries,
thoroughly clean compartment with a damp paper towel or follow battery manufacturer's recommendations
for cleanup. If uid from the battery comes into contact with skin or clothes, ush with water immediately.
• Remove batteries if your device is to be stored for an extended period of time without being used.
PRODUCT DISPOSAL INFORMATION
Dispose of this product in accordance with Local and National Disposal Regulations.
FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation.

11-1327