Ambiance Fireplaces Elegance 36 User manual

Elegance 36
Owner’s Manual
Model Number: 24SF
This product is proudly manufactured in North America by SUPREME FIREPLACES INC.
3594 Jarry East, Montreal, QC H1Z 2G4
T: 877-593-4722, F: 514-593-4424
www.supremem.com
Revised: May 2017
IMPORTANT: Keep the owner’s manual for future use.

ii
CONTENTS
1SAFETY.....................................................................................................................................................1
2GENERAL INFORMATION ........................................................................................................................2
2.1 Overall Dimensions .............................................................................................................................2
2.2 Specifications......................................................................................................................................3
2.3 Combustion Air Control .......................................................................................................................3
2.4 Cold Hand Key....................................................................................................................................4
2.5 Chimney Sweeping Cap......................................................................................................................4
2.6 Door....................................................................................................................................................4
2.7 Certification Label................................................................................................................................4
2.8 Removable Ash Lip.............................................................................................................................4
2.9 Optional Blower Kit..............................................................................................................................4
2.10 Optional Hot Air Kit..............................................................................................................................4
2.11 Optional Fresh Air Kit ..........................................................................................................................5
3INSTALLATION INSTRUCTIONS ..............................................................................................................6
3.1 Location...............................................................................................................................................6
3.2 Chimney Installation............................................................................................................................7
3.2.1 General Rules and Guidelines......................................................................................................7
3.2.2 Listed UL 103 / ULC S629 Approved Chimney Models (Reference Table)...................................8
3.2.3 Chimney Installation Instructions..................................................................................................8
3.2.4 Offset Installation..........................................................................................................................8
3.2.5 Angled Wall Radiation Shield .......................................................................................................9
3.2.6 Connecting to a Masonry Chimney...............................................................................................9
3.3 Façade Installation............................................................................................................................11
3.3.1 Traditional Façade......................................................................................................................11
3.3.2 Contemporary Façade................................................................................................................11
3.4 Framing.............................................................................................................................................12
3.5 Hearth Extension...............................................................................................................................12
3.5.1 Calculating R-Value....................................................................................................................12
3.6Chase Installation..............................................................................................................................13

iii
3.7 Clearances to Combustibles..............................................................................................................14
4OPTIONS.................................................................................................................................................15
4.1 Blower Kit..........................................................................................................................................15
4.2 Hot Air Kit..........................................................................................................................................16
4.3 Fresh Air Kit ......................................................................................................................................17
5OPERATION INSTRUCTIONS.................................................................................................................18
5.1 Fuel...................................................................................................................................................18
5.2 First Fires..........................................................................................................................................18
5.3 Operating the Combustion Air Control...............................................................................................18
5.4 Starting a Fire....................................................................................................................................19
5.5 Adding a New Load of Wood.............................................................................................................20
5.6 Blower Operation (Optional)..............................................................................................................20
6TROUBLESHOOTING .............................................................................................................................21
6.1 Backdraft / Smoking ..........................................................................................................................21
6.2 Over Firing ........................................................................................................................................21
7MAINTENANCE .......................................................................................................................................22
7.1 Disposal of Ashes..............................................................................................................................22
7.2 Chimney Maintenance.......................................................................................................................22
7.3 Cleaning of Glass..............................................................................................................................23
7.4 Replacing Soapstone Slab ................................................................................................................23
7.5 Replacement of Door Gasket ............................................................................................................23
7.6 Replacement of Glass.......................................................................................................................24
7.7 Door Latch Lubrication ......................................................................................................................24
7.8 Paint..................................................................................................................................................24
8WARRANTY.............................................................................................................................................25

1
WARRANTY REGISTRATION
Please register your SUPREME product online at http://www.supremem.com/registration.php to ensure
full warranty coverage. Proof of purchase is required for all warranty claims.
1 SAFETY
SUPREME FIREPLACES INC. congratulates you on purchasing an Elegance 36 wood burning fireplace. This
manual describes the installation and operation of the Elegance 36 non-catalytic wood heater. This heater
meets the 2020 U.S. Environmental Protection Agency’s crib wood emission limits for wood heaters sold after
May 15, 2015. Under specific test conditions this heater has been shown to deliver heat at rates ranging from
10,125 to 25,944 Btu/hr. In addition, this fireplace complies with the ULC-S610 and UL-127 standards.
SAFETY NOTICE: Carefully read this manual before installation and operation of this fireplace. A house
fire may result if not properly installed. To reduce the risk of a fire, follow the installation instructions.
Failure to follow instructions presented in this manual can lead to property damage, bodily injury or
even death. Alterations or modifications made on the unit or the installation is strictly forbidden as it
may predispose the user to hazardous risks. Contact your local building or fire officials for restrictions
and installation inspection requirements in your area and the need to obtain a permit.
WARNING: This unit is hot during operation; keep children, pets, flammable liquids, or combustible
materials at a safe distance. Ensure that all clearances to combustible materials are respected. Contact
with the unit during operation may cause severe harm. Install a safety screen to keep children and pets
away.
CAUTION:
Do not connect this unit to a chimney flue serving another appliance.
Do not connect to any air distribution duct or system.
Never use chemicals to ignite the fire.
Never burn waste or flammable fluids (such as gasoline, naphtha, or engine oil).
Only burn dry natural cordwood.
Never leave the unit unattended with the door open or unlatched.
Only refuel this unit when the wood is reduced to embers.
Always keep the door closed during operation.
Do not operate this unit with a fireplace grate.
Do not install an unvented gas log set into the firebox.
Do not install this unit in a mobile home.
Do not clean or service the unit while it is hot.
Allow proper air flow by keeping the louvers/openings clear of any obtrusions.
Note: Failure to respect the above cautions may cause damages to the unit, damages to personal property,
bodily harm and will void the warranty. “This wood heater needs periodic inspection and repair for proper
operation. It is against federal regulations to operate this wood heater in a manner inconsistent with
operating instructions in this manual.”

2
2 GENERAL INFORMATION
2.1 Overall Dimensions

3
2.2 Specifications
Appliance Type:
Adjustable Burn Rate Wood Heater –Non-Catalytic
Fuel Type:
Dry Cordwood
Maximum Log Length:
24 in (609 cm)
Burn Time1:
6 to 10 hrs
Firebox Volume:
2.4 ft3 (0.069 m3)
Heating Area:
500 to 2,000 ft2(45 to 185 m2)
Average Particulate Emissions Rate2:
1.77 g/hr
Average CO Emissions Rate3:
106.9 g/hr
EPA Protocol:
Method 28R, ASTM2780-10, and ASTM2515-11
Efficiency (Crib Wood):
HHV4: 67.14% | LHV5: 72.56%
Heat Output (Crib Wood):
10,125 to 25,944 BTU/hr (2,967 to 7,603 W)
Optimum Efficiency:
75%
Optimum Heat Output:
75,000 BTU (21.9 kWh)
Efficiency Protocol:
CSA B415.1-10
2.3 Combustion Air Control
The Combustion Air Control is a patented mechanism (Patent No: US 7,325,541 B2) that regulates the air flow
into the firebox based on the temperature of the unit. It is located on the top of the firebox, at the front center of
the unit. The combustion air control of the Elegance 36 has two components: the Activator and the Burn Rate
Selector. The left combustion control lever is the Activator. When starting a fire or adding a new load of wood,
the Activator must be pushed in to allow a primary source of air to enter the firebox. The Activator will retract
automatically with heat. The right combustion control lever is the Burn Rate Selector. The Burn Rate Selector
can slide sideways to achieve different burn rates. When the Burn Rate Selector is positioned to the left, a
maximum burn rate is achieved and when it is positioned to the right, a minimum burn rate is set. For optimum
efficiency, it is recommended to operate the unit with the Burn Rate Selector set at the low to medium/low
position.
WARNING: Never manipulate the Combustion Air Control with bare hands as it gets hot when the
Elegance 36 is in operation. Use the Cold Hand Key (see Section 2.3) to adjust the Combustion Air
Control.
1
Depending on combustion air control setting (see Section 5.3 for further details).
2
Officially tested and certified by an independent.
3
Note that rate is smaller for low to medium/low burn rates.
4
Higher Heating Value.
5
Lower Heating Value.

4
2.4 Cold Hand Key
The Cold Hand Key is an accessory that comes standard with the Elegance 36 fireplace. The Cold Hand Key
is a tool used to manipulate the Combustion Air Control Levers when it is hot.
2.5 Chimney Sweeping Cap
The chimney sweeping cap found at the baffle of the Elegance 36 allows easy access for chimney sweeping
without having to remove any components of the firebox.
WARNING: The chimney sweeping cap should be blocking the access to the chimney at all times
during combustion. A chimney sweeping cap that is not blocking the baffle hole during combustion is
a safety hazard, will overheat the fireplace and void the warranty.
2.6 Door
The Elegance 36 wood burning fireplace comes with a Pyroceramic glass panel door. Pyroceramic is the
highest grade available for fireplaces and stoves and can withstand temperatures up to 1300oF. To remove the
door, open the door, lift it and pull it towards the bottom until the rod exits from the hinge holes.
2.7 Certification Label
The certification label contains important information regarding the installation and operation of the Elegance
36 fireplace. In addition, the serial number of the unit is permanently embossed onto the top right corner. The
certification label is located below the bottom right corner of the door and is accessible by swiveling the plate.
2.8 Removable Ash Lip
The Ash Lip is a removable accessory that comes standard with the Elegance 36 fireplace. It is installed on the
door holder (under the two small angled tags below the door) and prevents ashes from falling onto the front of
the hearth. The Ash Lip can be installed with the door open or closed. It is safe to operate the unit without the
Ash Lip.
NOTE: The door of the Elegance 36 must remain closed at all times during operation.
2.9 Optional Blower Kit
An AC tangential optional blower (electrical rating: 115V, 60Hz, and 56W) with a variable speed control can be
installed into the Elegance 36 wood burning fireplace to maximize efficiency. Refer to Section 4.1 for
installation instructions.
WARNING: Make certain that the fireplace in not in operation and the blower is unplugged (breaker off)
before accessing the electrical wiring of the blower kit.
CAUTION: Only a blower provided by SUPREME FIREPLACES INC. can be installed into the fireplace.
Substituting the blower kit may result in overheating and will void the warranty.
2.10 Optional Hot Air Kit
The Optional Hot Air Kit allows heat to be drawn from the unit by a thermostatically controlled blower (electrical
rating: 115 V and 60 Hz) and dispersed to different areas of the house. This option is recommended when the
fireplace is installed in an area below the maximum heating space. A total of three kits can be installed onto

5
one unit with a maximum distance of 25 feet. Note that a 5 inch insulated duct is required for the installation
(item ordered separately). Refer to Section 4.2 for installation instructions.
WARNING: Make certain that the fireplace in not in operation and that hot air blower is not powered
(breaker off) before accessing the electrical wiring of the hot air kit.
CAUTION: Only a hot air kit provided by SUPREME FIREPLACES INC. can be installed onto the
fireplace. Substituting the hot air kit may result in overheating and will void the warranty.
2.11 Optional Fresh Air Kit
The Optional Fresh Air Kit allows for exterior air (outdoors) to be drawn into the fireplace during operation of
the unit. Note that a 4 inch insulated duct is required for the installation (item ordered separately). Refer to
Section 4.3 for installation instructions. Contact your local building official regarding mandatory fresh air kit
installations within your area.
CAUTION: Only a fresh air kit provided by SUPREME FIREPLACES INC. can be installed onto the
fireplace. Substituting the fresh air kit may result in overheating and will void the warranty.

6
3 INSTALLATION INSTRUCTIONS
Before installing the unit, consult an authority having jurisdiction (such as your municipal building department,
your fire department, your fire prevention department...) for any local codes and whether a permit is required.
In the absence of local codes, refer to the CSA B365 Installation Code for Solid Burning Appliances and
Equipment (Canada) or the ANSI NFPA 211 Standard for Chimneys, Fireplaces, Vents and Solid Fuel-Burning
Appliances (USA). CAUTION: Modifications/alterations to the unit/installation without written
authorization from SUPREME FIREPLACES INC. are strictly forbidden and will void the warranty. Refer
to Section 1 for further safety information. Carefully read the instructions below before installing your Elegance
36.
3.1 Location
Determine the location of the Elegance 36 by taking into consideration the following criteria:
The size of the room with respect to the heat output of the fireplace.
The proximity of windows, doors, and traffic flow.
The necessary amount of space in front of the unit for the hearth extension and mantel.
The clearances to combustible materials.
The passage of the chimney.
If possible, select a location for the fireplace that will minimize the number of offsets in the chimney course.
Offsets will reduce the draft, complicate the chimney sweeper’s work, and increase installation costs. Technical
drawings outlining the chimney route should be prepared prior to the installation. NOTE: The cutting of joists
and rafters for floor, ceiling, and roof chimney penetrations will affect the load bearing capacities of the dwelling
structure. To determine whether additional support is required, consult your local building codes. Improper
cutting of chimney openings in the attic and roof will affect the bearing and thermal insulating capacity, as well
as the weather tightness of the dwelling. Avoid incorrect workmanship by consulting a professional engineer or
a certified installer.
Through examination of the floor construction, ensure that the fireplace and chimney system is resting on a
surface capable of withstanding its weight. Consult your building codes to see whether additional structural
supports are required (applicable for rare and isolated cases).
Avoid having the chimney outlet near any obstructions (such as trees and roof offsets) as the draft of the
chimney may be affected by wind turbulence. Ideally position the outlet of the chimney at the highest area of
the roof.
NOTE: It is strongly recommended to install a carbon monoxide (CO) and smoke detector near the
location of the unit
Figure 3-2: Corner Installation
Figure 3-1: Straight Wall Installation

7
3.2 Chimney Installation
The Elegance 36 is approved with a 6” chimney that is listed under the UL
103 / ULC S629 standards (refer to Table). Note that when connecting a 7”
chimney, a 6” to 7” anchor plate adaptor from the same chimney
manufacturer must be installed onto the unit. WARNING: Mixing chimney
components from different brands is a safety hazard and will void the
warranty on the unit. When connecting the unit to an existing chimney,
thoroughly inspect the condition of the chimney and that the installation
conforms with the requirements of the chimney manufacturer and the
building codes. Note that to avoid any unnecessary risk, it is often
recommended to replace the chimney system. Always respect the
clearances to combustibles from the chimney manufacturers; 2” is usually
required for prefabricated chimneys.
3.2.1 General Rules and Guidelines
1. Carefully read the instructions from the chimney manufacturer prior to
installation (manuals can be obtained from the chimney manufacturer’s
website or from the vendor). Unless specified, follow the chimney
manufacturer’s instructions for proper installation.
2. For optimal performance of the unit, it is recommended to install the
chimney system in an interior setting. To prevent drafting issues and
creosote buildups, avoid exterior installations of the chimney system in
regions that experience extreme cold conditions.
3. The minimum and the maximum height of the chimney from the base of
the unit are 15’ and 35’ respectively.
4. Only chimneys approved under the UL 103 / ULC S629 standards can
be installed onto the unit (refer to Table).
5. A 6” anchor plate is required to connect the fireplace to the chimney
system. The anchor plate can be secured onto the unit with 4 self-
tapping screws.
6. The chimney installed onto the unit cannot be connected to another
appliance.
7. Enclose any portion of the chimney that extends to accessible spaces.
8. The clearance of the chimney to any combustible material cannot be
less than 2”; the 2” clearance cannot be filled with insulation or any
non-combustible material.
9. At least one support is to be incorporated in any chimney installation.
10. A firestop is required in the joists/frames where the chimney goes
through (ceilings, floors, walls, and roof).
11. To prevent drafting issues, avoid deviations wherever possible.
12. The chimney shall extend at least 3’ above its point of contact with the
roof and at least 2’ higher than wall, roof, or adjacent building within a
10’ radius.
13. A secure brace is to be installed if the chimney extends a minimum of 5’
above the contact point with the roof.
14. A rain cap must be installed on top of the chimney to avoid internal
damage and/or corrosion.
15. Consult the chimney manufacturer for clearances to combustibles when
installing a combustible chimney enclosure above the roof.
Figure 3-3: Straight Interior Installation
Figure 3-4: Exterior Installation

8
3.2.2 Listed UL 103 / ULC S629 Approved Chimney Models (Reference Table)
Note that the only chimney models certified under the UL 103 / ULC S629 standards can be installed on
Elegance 36. The table below serves as a reference for approved chimney models.
Manufacturer
Models
American Metal
HS, AC Triple Wall, 6” inner diameter
HSS, AC Triple Wall, 6” inner diameter
FMI (US only)
AC, AC Triple Wall, 6” inner diameter
ICC
Excel 2100, 1” Solid Pack, 6” inner diameter
Metal Fab
Temp Guard, 1” Solid Pack, 6” inner diameter
Olympia Chimney
Ventis, 1” Solid Pack, 6” inner diameter
Security Chimney
ASHT+, 1” Solid Pack, 6” inner diameter
S-2100+, 2” Solid Pack, 6” inner diameter
Selkirk
Super Pro (SPR), 1” Solid Pack, 6” inner diameter
Super Pro 2100 (ALT), 2” Solid Pack, 6” inner diameter
Hart & Cooley (TLC), 1” Solid Pack, 6” inner diameter
Sure-Temp (ST), 1” Solid Pack, 6” inner diameter
Super Vent (JSC), 1” Solid Pack, 6” inner diameter
Super Vent 2100 (JM), 2” Solid Pack, 6” inner diameter
Ultra-Temp (UT), 1” Solid Pack, 6” inner diameter
UltimateOne, 1” Solid Pack, 6” inner diameter
CF Sentinel (CF), 2” Solid Pack, 6” inner diameter
Simpson Dura-Vent
Dura Tech, 1” Solid Pack, 6” inner diameter
Dura Plus HTC, 2” Solid Pack, 6” inner diameter
Dura Plus, AC Triple Wall, 6” inner diameter
3.2.3 Chimney Installation Instructions
1. Cut and frame square openings in the floors, ceilings, and roof where the chimney will pass through while
taking into consideration the minimum clearance to combustibles.
2. In the ceiling/floor openings, install a chimney manufacturer’s firestop from below. Install the chimney
manufacturer’s attic radiation shield from above in the chimney opening to the attic. Ensure to install the
appropriate firestop for ceilings and walls.
3. Install the chimney manufacture’s anchor plate onto the unit.
4. Install the chimney lengths according the manufacturer’s instructions and ensure proper fastening/locking
of the joints.
5. Install the roof support once the desired height has been reached.
6. Position the roof flashing. Note that for sloping roofs, position the upper portion of the flashing under the
shingles and position the lower portion of the flashing above the shingles. Seal the joint between the roof
and the flashing with roofing cement or silicone. Secure the flashing to the roof with roofing nails.
7. Install the storm collar over the flashing by tightening the supplied bolt or through the flange mechanism
(depends on chimney brand). Seal the joint between the storm collar and the chimney using a silicone
caulking. WARNING: Do not seal, caulk, or obstruct the ventilation openings when installing a
ventilated flashing.
8. Install the chimney rain cap.
Refer to Figure 3-3 and Figure 3-4 for typical chimney installations.
3.2.4 Offset Installation
An offset installation (Figure 3-7) consists of the use of elbows to deviate from unavoidable obstacles or to
extend the chimney outside. The following list is a few general rules to take note when installing offsets:

9
A maximum of 2 offsets (2 elbows per offset) is permitted per installation.
The maximum deviation is 45oin Canada and 30oin the US.
Secure the elbows and the chimney components according the
instructions from the chimney manufacturer.
A support strap, a wall support, or a roof support must be installed above
each offset to allow adequate support to the vertical chimney lengths.
Never install an elbow in an opening of a floor, wall, ceiling, or roof.
In addition, only vertical chimney sections can be installed within
ceiling/floor openings.
Install a support for the first 15’ of chimney.
The following are instructions for offset installations:
1. Rotate the elbow in the required direction and secure it to the adjacent
chimney section according to the chimney manufacturer’s instructions.
2. Follow to the chimney manufacturer’s instructions to install the chimney
length(s) necessary for the offset.
3. Once the desired offset length has been achieved, install the second
elbow to redirect the venting to the vertical position.
4. Cut an opening in the floor/ceiling to allow the chimney to pass through.
5. Install the appropriate firestop.
CAUTION: For offset installations, always install a ventilated flashing
and a roof firestop unless otherwise specified by the chimney
manufacturer.
3.2.5 Angled Wall Radiation Shield
For chimney installations requiring to pass through a combustible wall at a 30o
(Canada) or 45o(Canada and US) angle, an angled firestop or an angled wall
radiation shield from the chimney manufacturer must be installed within the
wall opening. Install the angled firestop and angled wall radiation shield according to the manufacturer’s
instructions. It is recommended to use an insulated angled wall radiation shield in areas that experience cold
climates.
3.2.6 Connecting to a Masonry Chimney
The Elegance 36 fireplace can be connected to a masonry chimney that complies with current national and
municipal building codes. A 6” chimney liner that complies with ULC S635 M2000 (Canada) or UL 1777 (US)
standards must be installed within the existing masonry chimney. Note that the 6CON connector
(manufactured by SUPREME FIREPLACES INC.) must be installed to connect the prefabricated chimney to
the liner (6CON sold separately).
Note that prior to installation, an inspection from an authority having jurisdiction is required to determine
whether the masonry chimney:
Is constructed in accordance with national and municipal building codes.
Is in good condition. Note that repairs must be performed on any cracked or missing bricks.
Is thoroughly cleaned of any soot or creosote.
Is not connected to another appliance such as a furnace, hot water heater, or another fireplace.
Has a flue of adequate size for proper installation of the venting.
Respects minimum clearances to combustibles.
It is recommended to position the fireplace as close as possible to the masonry chimney to ensure proper
venting. The prefabricated chimney must penetrate at least 3” within the masonry chimney before connecting
Figure 3-7: Offset Installation

10
the liner. Elbows can be used within the masonry chimney, with a maximum deviation of 30oin US and 45oin
the Canada.
The installation of the prefabricated chimney and the liner must comply with the manufacturer’s instructions.
The following are instructions in installing the venting of the Elegance 36 running through a masonry chimney:
1. Install the anchor plate onto the unit.
2. Position the fireplace to the recommended location.
3. Install the initial prefabricated chimney lengths and elbows.
4. Mark the area where the prefabricated chimney will penetrate the masonry chimney.
5. Remove the fireplace to allow for sufficient space to work.
6. Make a hole to the required size to allow for the prefabricated chimney to be inserted freely in the
masonry chimney. Note that the appropriate firestops need to be installed if running the prefabricated
chimney through a combustible wall.
7. Install the remaining prefabricated chimney components center with the masonry chimney.
8. Align the flange holder of the 6CON connector with the studs facing upwards to the center of the
prefabricated chimney section (elbow or tee) and secure it with three self-tapping screws.
9. Reposition the fireplace to its initial position.
10. Overlap by 1” the lower end of the liner in the expanded portion of the 6CON connector and secure the
joint with 3 #8 stainless steel self-tapping screws.
11. From the roof, slid the liner down the masonry chimney until it reaches the upper end of the
prefabricated chimney.
12. Install the upper portion of the 6CON liner connector to the flange holder by aligning the threaded studs
to the holes and complete the connection by tightening the wing nuts.
13. Seal any openings around the prefabricated chimney and the 6CON connector with refractory cement
resistant to high temperatures.
Figure 3-8: (A) Connection into a masonry chimney through an elbow/liner; (B) connection into a masonry chimney through a tee/liner;
(C) detailed drawing of masonry chimney connection.

11
3.3 Façade Installation
The Elegance 36 can be installed with either the traditional façade or the contemporary façade.
3.3.1 Traditional Façade
The traditional façade comprises louvers below (intake) and above (outtake) the door. All components and
fasteners are included in the façade kit.
1. Remove the door of the unit and place it on a soft surface, such as a carpet or cardboard, to avoid any
scratches or damages.
2. Align the bottom bracket to the intake opening and fasten it in place.
3. Align the upper bracket to the outtake opening and fasten it in place.
4. Place the façade within the door holder and secure it in place with 4 black screws (one on each corner).
Make sure that the handles of the Primary Air Control pass through the slots of the façade.
5. Place back the door.
3.3.2 Contemporary Façade
The contemporary façade comprises no louvers; however, an intake into the chase and outtake through gravity
ducts is required for this façade configuration. The instructions below describe the installation of the
contemporary façade, the intake openings, and the gravity ducts/outtakes. Note that in order to connect the
gravity ducts, the sides of the chase need to be constructed and the front of the chase needs to remain open
(Refer to Figure 3-11).
1. Remove the door of the unit and place it on a soft surface, such as a carpet or cardboard, to avoid any
scratches or damages.
2. Align the bottom bracket and fasten it in place.
3. Align the upper bracket and fasten it in place.
4. Place the façade within the door holder and secure it in place with 4 black screws (one on each corner).
Make sure that the handles of the Primary Air Control pass through the slots of the façade.
5. Place back the door.
6. Remove the two 8” knockouts (2) at the top of the unit using a flat head screwdriver.
7. Using the knockout as a template, cut the exposed insulation. Make sure to remove any pieces of
insulation that has fallen into the unit.
8. Install the 8” flange adaptors through the newly cut knockouts and fasten them to the top of the unit.
Make sure to bend the tabs of the adaptors before installation.
9. Determine the two locations of the air intakes on the chase and cut a rectangular opening 10.5” (W) X
9.5” (H). Note that a distance of 3” is required from the floor.
10. Determine the two locations of the air outtakes on the chase and cut a rectangular opening 10.5” (W) X
9.5” (H). Note that a minimum distance of 68” is required from the floor.
11. From the exterior of the chase, place the duct/louver adaptor into the air outtake hole and secure it onto
the wall with screws. Repeat for the other outtake.
12. Within the chase, place the grooved end of the adjustable 45oelbow into the flange of the duct/louver
adaptor and secure it using an aluminum tape. Repeat for the other outtake.
13. Measure the distance between the flange on top of the unit and the flange of the duct/louver adaptor
and cut the 8” semi-rigid insulated duct (SUPREME part number UCAC8) to the necessary length.
Repeat for the other outtake.
14. Complete the connection by sliding the ducts over the flanges and tighten the joints with the worm gear
clamps.
15. From the exterior of the chase, fasten the grills over the intake and outtake openings with the white
screws.

12
3.4 Framing
The Elegance 36 can be placed directly onto or against
normal, combustible construction materials such as
lumber, plywood, millboard, particleboard, drywall and
decorative wood paneling. The fireplace should NOT be
placed directly against or be in contact with an insulation
material. A portion of the framing on the face of the chase
must be constructed with nominal 2" x 3" metal studs and
the remainder can be constructed with nominal 2” X 3”
lumber. Refer to Figure 3-9 for framing design. The
framing must be nailed or screwed onto the floor and to the
ceiling.
CAUTION: Do not construct the framing with
combustible material in front of the chimney; respect
the framing design outlined in Figure 3-9.
WARNING: Do not nail or screw framing components
onto the fireplace.
3.5 Hearth Extension
The hearth extension of the Elegance 36 must
comprise of a non-combustible material, such
as steel, cement or mortar, bricks, or ceramic
tiles. Note that unidentified materials may be
combustible; verify product specifications prior
to installation. In addition, the non-combustible
hearth extension must be constructed of
materials having a minimum R-Value of
0.390. The hearth extension must extend a
minimum of 18” from the front of the door, 8”
from side of the outer frame of the door, and
extended all the way to the back of the unit
(see Figure 3-10 for dimensions).
CAUTION: Make sure to remove any carpet
or fabric under the hearth extension.
3.5.1 Calculating R-Value
The R-Value is a dimensionless measurement
of a material’s insulating properties with
respect to a referenced thickness (see Table 3-
1). The total R-Value of the hearth extension
constructed out of different materials can be
calculated by summing the R-Value of each
material with respect to the thickness (see
equation below).
Figure 3-9: Framing Design of Elegance 36
Figure 3-10: Hearth Extension

13
Figure 3-11: Front Face of Chase
Table 3-1: Thermal Properties of Materials
Material
Thermal Resistance
[R-Value] per Inch
Thermal Conductivity
[k-Value] per Inch
Cement Board (Durock)
0.780
1.282
Brick
0.200
5.000
Limestone
0.153
6.536
Slate
0.100
10.000
Concrete
0.095
10.526
Marble
0.090
11.111
Granite
0.083
12.048
Ceramic Tile
0.080
12.500
RTotal = (R1×T1) + (R2×T2) + (R3×T3) +…
Note the k-Value per inch can be converted to an R-Value per inch using the following formula:
R= 1
k
Example:
A hearth extension is constructed out of 4” of concrete with ¼” ceramic tiling. The total R-Value is:
RTotal = (Rcon×Tcon)+ (Rcer×Tcer) = (0.095 × 4")+ (0.080 × 0.25") = 0.400
As 0.400 is greater than 0.390, this hearth extension meets the requirements for the Elegance 36.
3.6 Chase Installation
A portion of the front of the chase must be constructed out
non-combustible material. Refer to Figure 3-11 for
dimensions. Note the chase must be properly fastened
onto the framing structure.
WARNING: Do not nail or screw the chase onto the
fireplace.
For the contemporary façade option, two intake and two
outtake openings must be constructed onto the chase.
Refer to Figure 3-12 for minimum clearances.
Figure 3-12: Contemporary Facade Chase

14
3.7 Clearances to Combustibles
The clearances below must be respected to ensure safe operation of the unit under normal and extreme
conditions. Failure to follow the information below is a safety hazard and may result in property damage.
Table 3-2: Overall Clearances
Combustible
Clearance
Reference
Side Wall
16” (406 mm)
Outer edge of fuel door
Side Trim
3” (76 mm)
Outer edge of fuel door
Ceiling
84” (2133 mm)
Base of unit
Table 3-3: Mantel Clearances
The depth of the mantle is measured from the face of the
fireplace door. When the non-combustible wall is recessed,
the depth of the mantle can be increased by the amount of
the recess (see Figure 3-13). Note that a mantel cannot be
installed below the minimum clearance of 51.5” (from the
bottom of the mantle to the base of the unit).
Figure 3-13: Mantle Clearances
Maximum
Mantle Depth
Distance from the Base of
the Elegance 36 to the
Bottom of the Mantle
3” (76 mm)
51.5” (1308 mm)
5” (127 mm)
53.5” (1359 mm)
7” (178 mm)
55.5” (1410 mm)

15
4 OPTIONS
4.1 Blower Kit
The Elegance 36 can be installed with a high
performance 250 CFM blower kit, which has an
electrical rating of 115 V, 60 Hz, and 56 W. A
variable speed control (rheostat) and a heat
sensor (therm-o-disc) are included with the kit.
WARNING: Do not install a substitute kit. The
electrical connection of the fans is to be
performed by a certified electrician. Note that it is
recommended that the wiring of the fans be done
before the installation of the façade kit. The fan
and the electric box are located respectively at
the back/bottom and at the front/bottom of the unit
(Figure 4-1).
For maintenance or replacement purposes, the fan and the
electrical box are accessible from within the bottom of the
firebox (Figure 4-2). 1) Remove the floor plate. 2)
Disassemble and remove the stainless steel cover on the
bottom of the firebox by unscrewing it. Take caution to the
therm-o-disc and wiring assembled onto the stainless steel
bracket.
The following are instructions on installing the blower kit into
the Elegance 36 (refer to Figure 4-3 for the electrical
diagram):
1. Using two screws, install the therm-o-disc onto the L
bracket located under the firebox.
2. Connect the black wire of the power supply to the therm-
o-disc.
3. Connect the therm-o-disc to the black wire of the rheostat
(install/mount the rheostat at a convenient location).
4. Connect the white wire of the rheostat to the blower.
5. Connect the blower to the white wire (neutral) of the
power supply.
6. Ground the connection with the green wire in the electric
box.
Once the electrical connections are completed, the fans will
turn on and turn off automatically during the operation of the
unit. As the temperature of the fireplace increases and the
therm-o-disc reaches 95°F, the fans will turn on. Note that
the average time it takes for the fans to activate is between
30 to 45 minutes after starting a fire. The fans will turn off
once the fireplace has cooled down and the therm-o-disc is
85°F. The speed of the fans can be adjusted with the variable
speed control (rheostat) mounted on the wall. It is safe to
operate the Elegance 36 in the event of a power failure (fans
not powered).
Figure 4-1: Location of Blower
Figure 4-3: Electrical Diagram
Figure 4-2: Access to Blower

16
4.2 Hot Air Kit
The hot air system is an optional kit intended to bring hot air from the fireplace to a remote area using a 250
CFM blower. The system is designed to distribute heat with ducting lengths up to 25’. Note that only an
insulated flexible duct capable of withstanding a maximum temperature of 210oF can be installed with this kit.
WARNINGS
Do not install within the casing of the fireplace.
Respect the minimum distances to combustible
materials when the hot air duct passes through
the chase of the fireplace. Properly secure the
duct to avoid accidental displacement.
Install the blower a minimum distance of 3 feet
away from the fireplace.
Do not use a speed control for the blower.
Installation:
1. Remove the 5’’ knockout on the exterior casing of the
fireplace using a flat head screwdriver.
2. Install the fireplace duct connector (FDC - #5) on the
opening using four screws.
3. In the room where the heat will be distributed, cut an
opening of 6”X 7.5”.
4. Find a suitable location to install the blower (701710 - #2).
5. Install the wall-duct connector (WDC - #7).
6. Install the air duct (UCAC5 - #4)* and secure it with a
clamp (CLP - #1).
7. Install the wall grill (HAG - #6).
8. Make the electrical connections (Figure 11). Note that the
power supply to the blower is 115V.
Figure 4-6: Electrical Diagram for Parallel Connection of Hot Air Kit and Blower Kit
Figure 4-4: Hot Air Kit Parts List
Figure 4-5: Electrical Diagram for Hot Air Kit

17
4.3 Fresh Air Kit
Sufficient air exchange is necessary for the fireplace to operate properly and to maintain a good combustion. In
an airtight household, the fireplace may not function as designed due to a lack of air; it is therefore
recommended to install the fresh air kit in such cases. The fresh air system is an optional kit intended to bring
combustion air into the fireplace from an exterior source.
Note that the Elegance 36 is designed to use a minimum amount of air during operation. Using an air
exchanger or simply opening a nearby window/door during the ignition of the unit will achieve a similar result
as the fresh air kit. When the fireplace is idle, there is no air escaping from the house through chimney.
Consult a local authority having jurisdiction (such as the fire department, the municipal building
department, the fire prevention bureau…) to determine if it is mandatory to install a fresh air kit in your
area.
General Notes:
The outside air kit should be installed according to the following
guidelines:
The air duct must be insulated, wrapped with a vapor barrier, and
have an inner diameter of 4”.
The length of the air duct should be as short as possible.
Fresh air must come from the outside and not from another room
or the attic.
The outside register must be away from automobile exhaust
fumes, gas meters, or other vents.
Avoid installing the air register where it will likely be covered by
snow or exposed to strong winds.
The air register can be installed above or below the level where
the fireplace.
Use the SUPREME FIREPLACES INC. Fresh Air Adaptor (ADP4)
Use the SUPREME FIREPLACES INC. Fresh Air Kit (UPEA4) or
any other fresh air kit with the same specifications and intended
for fireplace use.
Installation:
1. Cute 4 ½” diameter hole on the exterior
wall of an ideal location.
2. Install the air register on the exterior wall.
3. Insert the fresh air adaptor (ADP4) into
the fireplace from the exterior casing.
Make sure that the adaptor is properly
inserted into the combustion air box on
top of the firebox.
4. Secure the fresh air adaptor to the side of
the fireplace using two screws.
5. Install the air duct and secure it with
worm gear clamps.
Figure 4-7: ADP4 Installation in Fireplace
Figure 4-8: Installation of Fresh Air Kit