Ambiance Fireplaces Inspiration 34 Series User manual

MODEL: UF0600
UF0610
GAS FIRED DIRECT VENT
FIREPLACE INSERT
S/N 630562 AND UP
ARCHGARD FIREPLACE PRODUCTS
7116 Beatty Drive
Mission, BC V2V 6B4 Canada 200-0600-07
November 13, 2019
English and French Installation Manuals available through your
local dealer or visit our website at: www.archgard.com
Les manuels d'installation en anglais et en français son
disponibles chez votre détaillant local ou en visitant notre site
web: www.archgard.com
INSTALLER:
LEAVE THIS MANUAL WITH THE APPLIANCE.
CONSUMER:
RETAIN THIS MANUAL FOR FUTURE REFERENCE.
This appliance may be installed in an aftermarket
permanently located, manufactured home (USA only) or
mobile home where not prohibited by local codes.
This appliance is only for use with the type of gas indicated
on the rating plate. This appliance is not convertible for use
with other gases, unless a certied kit is used.
INSTALLATION, OPERATION, AND
MAINTENANCE MANUAL
Do not store or use gasoline or other ammable vapors or
liquids in the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance
• Do not touch any electrical switch; do not use any phone in
your building
• Immediately call your gas supplier from a neighbors phone.
• Follow the gas suppliers instructions
• If you can not reach your gas supplier, call the re
department
Installation and service must be performed by a qualied
installer, service agency or the gas supplier.
WARNING: If the information in this manual is not followed
exactly, a re or explosion may result causing property
damage, personal injury or loss of life.
Inspiration 34
Gas Fireplace Energy E󰀩ciency Rating
71.93%
Based on CSA P.4.1-15

2
TABLE OF CONTENTS
1.0 Introduction 3
2.0 Safety Information 4
3.0 Technical Information 5
3.1 Appliance Certication 5
3.2 Installation Codes 5
3.3 Specications 5
3.4 High Altitude Installation 5
4.0 Rating Plate 6
5.0 Installation Checklist 7
6.0 Appliance Overview 8
6.1 Rating Plate Location 8
6.2 Appliance Overview 8
6.3 Leveling the Appliance 8
6.4 Accessing the Control Board 9
7.0 Electrical Connections 9
8.0 Appliance Dimensions 10
9.0 Minimum Opening Dimensions 11
9.1 Factory Built Fireplaces 12
9.2 Refacing a Masonry Fireplace 13
10.0 Clearances to Combustibles 14
10.1 Mantel Clearances 14
10.2 Sidewall Clearances 14
10.3 Hearth Clearances 15
10.4 Hearth Protection 15
11.0 Gas Connections 16
11.1 Clocking Procedure 16
12.0 Conversion Kit Instructions 17
12.1 Prepare the Fireplace 17
12.2 Pilot Conversion 17
12.3 Convert the Gas Valve 18
12.4 Complete the Conversion 18
13.0 Venting Instructions 19
13.1 Approved Terminations 19
13.2 Vent Slider Installation 21
13.3 Min/Max Vent Run 22
13.4 Using a Co-linear to Coaxial Adapter 23
14.0 Barrier Screen Installation 24
15.0 Glass Door Installation 25
15.1 If Your Glass Breaks 26
16.0 Surround Installation 27
16.1 Bottom Filler Plate 28
17.0 Firebox Liner Installation 29
17.1 Brick Panel Installation 29
17.2 Reective Glass Installation 31
18.0 Media Installation 33
18.1 Log Set (UF0600) 33
18.2 Fire Beads (UF0610) 37
18.3 River Rocks (UF0610) 38
19.0 Operation 39
19.1 Before Lighting 39
19.2 First Fire 39
19.3 Lighting Instructions 40
19.4 Dynamic Start Advantage 41
19.5 Remote Control Operation 42
20.0 Maintenance 49
20.1 Cleaning the Appliance 49
20.2 Servicing Under Warranty 50
20.3 Checking Inlet and Outlet Pressure 50
20.4 Checking and Adjusting Pilot 50
20.5 Adjusting the Primary Air 51
20.6 Replacing Batteries 52
20.7 Replacing Fuse 52
20.8 Replacing Light Bulbs 53
20.9 Replacing the Control Board 54
20.10 Replacing the Burner 56
20.11 Replacing the Pilot 58
20.12 Replacing the Fan 61
20.13 Replacing Light Bases 63
20.14 Wiring Schematic 65
20.15 Troubleshooting 66
21.0 Frequently Asked Questions 67
22.0 Replacement Parts List 68
Warranty Information 69
10 Year Limited Warranty 69
Lifetime Warranty 70

3
General Information
1.0 Introduction
Thank You and Congratulations for choosing an Ambiance Gas Fireplace!
The UF0600 / UF0610 is one of the most advanced Direct Vent Insert heaters available today. It is solidly designed using the latest
technology and manufactured to the highest quality. It is our aim to provide you with an appliance that brings many trouble-free years of
reliable service.
Some of the many features of your UF0600 / UF0610 are:
• Heater Classication This replace is classied as a heating appliance. Therefore, it uses Direct Vent safety technology
and it is suitable for continuously operated zone heating.
• High E󰀩ciency This replace has one of the highest e󰀩ciencies of any Direct Vent gas insert, ensuring it is less
expensive to operate.
• Adjustable Fan Speed This replace comes complete with an adjustable six speed circulation fan controlled with the
remote.
• Adjustable Flame This replace provides the ability to adjust the ame aesthetics and heat output to suit the owner's
liking and heating needs.
• Adjustable Lighting Use the included remote to choose from six levels of accent lighting or leave the light o󰀨 and allow
the ame to provide a ickering glow.
• Solid Construction This replace is mainly constructed of 16 and 18 gauge galvanized and aluminized coated steel for
long life and durability.
• Optional Accessories Speak with your local Authorized Ambiance Dealer for a full complement of decorative accessories
to suit your home's decor and personal tastes.
• Electronic Control System This replace comes standard with the Dynamic Start Advantage. This new electronic ignition
system is the latest in replace technology. It helps to create a better draft, better ame
appearance, less condensation on the glass, and years of carefree operation. See Section 19.4 for
complete explanation of how the system works.
• Multiple Electronic Pilot
Settings This replace uses a gas control valve that is operated by a Multifunction Remote Control. It can be set up as either an Intermittent Pilot Ignition (IPI) system, or Continuous Pilot on Demand Ignition
(CPI) system (also known as a Pilot on Demand (POD)).
CPI vs IPI:
Continuous Pilot on Demand Ignition (CPI): In this mode the pilot runs continuously even when the main burner is o󰀨. The
Continuous Pilot on Demand Ignition operates on a seven day cycle. If the main burner is not turned on for seven continuous days, the
pilot will turn itself o󰀨. When the main burner is lit again the cycle repeats. The pilot will remain lit for seven days, even after the main
burner is turned o󰀨. If the main burner is lit during a seven day timing cycle, the seven day timer will reset.
Intermittent Pilot Ignition (IPI): A fuel saving mode in which the pilot is only used when the main burner is on.
This appliance is shipped in IPI mode. IPI mode is often the preferred method, however, there are some situations where it may be
preferable to switch the replace into CPI mode. For example, in colder climates the glass door or the front of the replace could
become very cold to the touch. Dynamic Start Advantage will solve most problems experienced by older IPI operated replaces.
Please complete and submit the warranty registration card included in the back of this manual or by visiting us at:
www.archgard.com/warranty-registration

4
General Information
2.0 Safety Information
Caution
FOR YOUR SAFETY - Do not install or operate your UF0600 / UF0610 without reading and understanding this manual. Any installation
or operational deviation from this instruction manual voids the warranty and may prove hazardous.
This appliance must be installed by a qualied gas installer and the installation must conform to the installation codes.
Provide adequate clearance around air openings into combustion chamber.
Never obstruct front openings.
Provide adequate clearances for proper operation and servicing of the appliance.
This appliance must be properly connected to an approved venting system and must not be connected to a chimney ue serving a
separate solid fuel burning appliance.
Flow of combustion and ventilation air must not be obstructed.
Always provide adequate clearance around the intake and exhaust openings.
Safety
Due to high temperatures, the appliance should be located out of tra󰀩c and away from furniture and draperies.
Children and adults should be alerted to the hazards of high surface temperature and stay away to avoid burns or clothing ignition.
Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children and others
may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals in the house. To
restrict access to a replace or stove, install an adjustable safety gate to keep toddlers, young children and other at risk individuals out
of the room and away from hot surfaces.
Do not store or place combustibles, gasoline, and other ammable vapors and liquids near the appliance.
Clothing or other ammable material should not be placed on or near the appliance.
Do not operate with cracked or broken glass. Do not to strike or slam the glass.
WARNING: Do not operate appliance with the glass front removed, cracked, or broken. Removal of the glass should be done by a
licensed or qualied service person.
Any safety screen or guard removed for servicing an appliance must be replaced prior to operating.
Installation and Repair should be done by a qualied service person. The appliance should be inspected before use and at least
annually by a professional service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding
materials, etc. It is imperative that the control compartments, burners and circulating air passageways of the appliance are kept clean.
Do not use this appliance if any part has been under water. Immediately call a qualied service technician to inspect the appliance and
to replace any part of the control system and any gas control which has been under water.
Each Ambiance Gas Fireplace is checked and tested at the factory prior to being packaged and shipped to our dealers and nally
installed in your home. Before leaving this unit with the customer, the installer must ensure that the appliance is ring correctly and that
the electrical system is in working order. The Installation Checklist in Section 5.0 should be used to ensure the proper installation of this
gas replace insert and to document any deviations from a typical install.
Any alteration to the product that causes carbon or soot deposits that results in any damage or requires
cleaning is not the responsibility of the manufacturer.

5
General Information
3.0 Technical Information
3.1 Appliance Certication
This appliance was listed by QAI Laboratories Inc to the following USA and Canadian gas appliance standards.
- ANSI Z21.88-2014/CSA 2.33-2014 Vented Gas Fireplace Heaters
- CAN/CGA-2.17-M91(R2014), Gas-Fired Appliances for Use at High Altitudes
- CSA P.4.1-15 testing method for measuring annual replace e󰀩ciency
- CSA C22.2 No.3 - M1998(R.2014) - Electrical Features of Fuel-Burning Equipment
The listing label is attached to the appliance on the bottom right side of the appliance.
A copy is shown on Section 4.0.
Commonwealth of Massachusetts: This appliance has been manufactured in accordance with Massachusetts code 248 CMR 5.00.
Approval Code: G1-1216-246. (http://www.mass.gov/ocabr/licensee/dpl-boards/pl/).
Please contact Archgard Industries Ltd., if you have any questions regarding the certication of this appliance.
3.2 Installation Codes
This appliance must be installed by a qualied gas appliance installer. The installation must conform with the local codes or, in
the absence of local codes, with the current National Fuel Gas Code ANSI Z223.1/ NFPA 54 in the US, or Installation Code CAN/
CGA-B149.1 in Canada. Electrical connections and grounding must conform with local code, or current National Electrical code ANSI/
NFPA No. 70-1987 in the US, and in Canada the current Canadian Electrical Code CSA C22.1.
We recommend that our gas hearth products be installed and serviced by professionals who are certied in the U.S. by the
National Fireplace Institute® (NFI) as NFI Gas Specialists.
3.3 Specications
Natural Gas (NG) Propane (LP)
Manifold Pressure 1.1 - 3.8 in. W.C. (0.3 - 0.9 kPa) 2.9 - 11.0 in. W.C. (0.7 - 2.7 kPa)
Min. Supply Pressure
Max Supply Pressure 5.0 in. W.C. (1.2 kPa) 14.0 in. W.C. (3.5 kPa)
12.0 in. W.C. (2.7 kPa)
14.0 in. W.C. (3.5 kPa)
Orice Size #31 DMS (3.05 mm dia.) #47 DMS (1.99 mm dia.)
Input Rating 21,000 - 40,000 BTU/hr
(6.15 - 11.72 kW)
20,000 - 40,000 BTU/hr
(5.86 - 11.72 kW)
P.4 Fireplace E󰀩ciency
(FE) 71.93%
P.4 Steady State E󰀩ciency 73.64%
Electrical Rating 120 VAC, 60 Hz less than 2 A.
Gas Control SIT 885 Proame II Dynamic Start Advantage with Continuous Pilot on Demand
Altitude 0 - 4500 ft (0 - 1372 m)
Primary Air Opening 1/8” (3mm) Open 1/2” (12.7mm) Open
3.4 High Altitude Installation
When installing this appliance beyond 4500 ft. (1372 M) above sea level, the appliance must be properly derated and installed
according to local codes, in the absence of local codes, with the current National Fuel Gas Code, ANSI Z223.1/ NFPA 54, in the US or
Installation Code, CAN/CGA-B149.1, in Canada.

6
General Information
4.0 Rating Plate
9-1/4”
12 ” SHEET
SHEET
SHEET
SHEET
November 13, 2019
UF0600 RATING PLATE
Material - Class III
Black Letters on silver Mylar background
MODEL: UF0600 (SIT 885 Proflame)
DO NOT REMOVE THIS LABEL
LISTED VENTED GAS FIREPLACE HEATER and GAS-FIRED APPLIANCES FOR USE AT HIGH ALTITUDES. Tested to: ANSI
Z21.88-2014 / CSA 2.33-2014, CAN/CGA 2.17-M91 (R2014), CSA P.4.1-15, and CSA 22.2 No.3-M1988 (R2014). This vented gas
replace heater is not for use with air lters. Certied for use in both CANADA and USA.
VENTED GAS FIREPLACE HEATER-NOT FOR USE WITH SOLID FUEL.
Manufactured as Natural Gas
NG LPG
Input rating 21,000 - 40,000 BTU/hr
(6.15 - 11.72 kW) 20,000 - 40,000 BTU/hr (5.86 - 11.72 kW)
Manifold Pressure 1.1 - 3.8 in. W.C. (0.3 - 0.9 kPa) 2.9 - 11.0 in. W.C. (0.7 - 2.73 kPa)
Orice size #31 DMS (3.05 mm dia.) #47 DMS (1.99 mm dia.)
Supply pressure (Min - Max) 5.0 - 14.0 in. W.C. (1.2 - 3.5 kPa) 12.0 - 14.0 in. W.C. (2.7 - 3.5 kPa)
Burner Primary Air Setting 1/8” (3mm) Open 1/2” (12.7mm) Open
Altitude 0 - 4500 ft (0 - 1372 m) 0 - 4500 ft (0 - 1372 m)
Gas Control SIT 885 Proame II Dynamic Start with Continuous POD
Electrical rating 120 VAC, 60 Hz, less than 2 A.
P.4.1 Fireplace E󰀩ciency (FE) 71.93%
Replacement fan Part no. RF-305-0624 fan or blower assembly must be used
Keep burner and control compartment clean. See
Instructions accompanying the heater.
Optional fuel conversion kit : See Manual
Minimum opening Dimensions:
34”(864 mm)W x 24”(610 mm)H x 16” (406 mm)D
Minimum Chimney Flue Size:
4” (102 mm) x 7” (178 mm)
Minimum clearances to Combustibles:
Sides from glass door frame: 8” (203 mm)
Max 8” (203 mm) mantle at min 24” (610 mm) from top of appliance
door.
See Manual for additional dimensions and clearances
This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI
Z223.1/NFPA 54, or Natural Gas and Propane Installation Codes, CSA B149.1. Electrical connections and grounding must
be in accordance with local codes, if any; if none, follow the current CAN/CSA C22.1 in Canada and ANSI/NFPA 70 in the
US. This appliance is certied for installation in a bedroom or a bed sitting room. This appliance is only for use with the gas
indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured (mobile) home where
not prohibited by local codes. See owner’s manual for details. This appliance is not convertible with other gases, unless a
certied kit is used.
WARNING: Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage. Refer
to the owner’s information manual provided with this appliance. For assistance or additional information consult a
qualied installer, service agency, or the gas supplier. This appliance must be properly connected to a Direct Vent
venting system in accordance with the manufacturer’s installation instructions.
WARNING: Failure to install this appliance per the manufacturer’s instructions or failure to use only parts specically
approved with this appliance may result in property damage or personal injury.
WARNING: Do not operate the appliance until all sections have been assembled and installed in accordance with the
manufacturer’s instructions.
WARNING: Operation of this appliance when not connected to a properly installed and maintained venting system can result
in carbon monoxide (CO) poisoning and possible death.
ONLY DOORS CERTIFIED WITH THE APPLIANCE SHALL BE USED.
For use only with barrier part # URP-891-0200. Follow installation instructions.
Made in Canada by:
Archgard Industries Ltd.
7116 Beatty Dr., Mission, B.C.
November 2019 303-6060-05
NE PAS ENLEVER CETTE ÉTIQUETTE
RADIATEUR VENTILE, CIRCULATEUR DU TYPE VENTILATEUR. Testée selon les normes : ANSI Z21.88-2014 / CSA 2.33-2014,
CAN/CGA 2.17-M91 (R2014), CSA P.4.1-15 et CSA 22.2 No.3-M1988 (R2014). Ne pas utiliser de ltre à air avec ce foyer au gaz à
évacuation. Certié pour utilisation dans le Canada et les ÉTATS-UNIS.
FOYER AU GAZ À ÉVACUATION. NE PAS UTILISER AVEC DU COMBUSTIBLE SOLIDE.
Fabriqué comme gaz naturel.
NG LPG
Entrée assignée 21 000 - 40 000 BTU/hr
(6,15 - 11,72 kW) 20 000 - 40 000 BTU/hr (5,86 - 11,72 kW)
Pression d’admission 1,1 - 3,8 in. W.C. (0,3 - 0,9 kPa) 2,9 - 11,0 in. W.C. (0,7 - 2,73 kPa)
Dimension de l’orice #31 DMS (3,05 mm dia.) #47 DMS (1,99 mm dia.)
Pression d’alimentation (Min - Max) 5,0 - 14,0 in. W.C. (1,2 - 3,5 kPa) 12,0 - 14,0 in. W.C. (2,7 - 3,5 kPa)
Réglage de l’air primaire du brûleur 1/8 po (3mm) Ouvrir 1/2 po (12.7mm) Ouvrir
Elevation 0 - 4500 ft (0 - 1372 m) 0 - 4500 ft (0 - 1372 m)
Contrôle du gaz SIT 885 Proame II Démarrage dynamique avec POD continu
Tension électrique 120 V, 60 Hz, Moins que 2 A.
P.4.1 E󰀩cacité du foyer (FE) 71,93%
Ventilateur de remplacement Le ventilateur ou l’ensemble RF-305-0624 doit être utilisé
Maintenir propres le brûleur et le compartiment
de commande. Voir les instructions relatives à
l’installation et au fonctionnement qui accom-
pagnent le radiateur.
Trousse de conversion de combustible option-
nel : Voir le manuel
Minimales dimensions d’ouverture:
34 po (864 mm)W x 24 po (610 mm)H x 16 po (406 mm)D
Cheminée minimale de fumée:
4 po (102 mm) x 7 po (178 mm)
Minimales entre l’appareil et les combustibles:
Côtes: 8 po (203 mm)
Max 8 po (203 mm) au manteau min 24 po (610mm) du haut de la porte
de l’appareil.
Voir le manuel pour les dimensions et les dégagements
supplémentaires
Il faut que cet appareil soit installé selon les codes locaux, s’il y en a; sinon, suivre le CAN/CGA-B149.1 actuel au Canada
et ANSI Z223.1 aux É.-U. Il faut que le raccordement électrique et la mise à la masse soient en conformité avec les codes
locaux, s’il y en a; sinon, suivre le CAN/CSA C22.1 actuel au Canada et ANSI/NFPA 70 aux É.-U. Cet appareil est certié
pour l’installation dans une chambre à coucher ou une pièce qui sert de chambre. Cet appareil doit être utilisé uniquement
avec le type de gaz indiqué sur la plaque signalétique. Cet appareil peut être installé dans une maison préfabriquée ou
mobile (É.-U. seulement) installée à demeure si les règlements locaux le permettent. Voir la notice de l’utilisateur pour plus
de renseignements. Cet appareil ne peut pas être utilisé avec d’’autres gaz sauf si une trousse de conversion certiée est
fournie.
AVERTISSEMENT: Une installation, un réglage, une modication, une réparation ou un entretien mal e󰀨ectué peut causer des
dommages atériels ou des blessures. Voir la notice de l’utilisateur qui accompgne l’appareil. Pour de l’aide
ou des renseignements supplémentaires, consultez un installateur, un technicien agréé ou le fournisseur
de gaz. Cet appareil doit être corectement raccordé à un système d’évacuation direct, conformément aux
instructions du fabricant.
AVERTISSEMENT : Risque de dommages ou de blessures si l’appareil n’est pas installé selon les instructions du fabricant
ou si des pièces autres que celles spéciquement approuvées avec cet appareil sont utilisées.
AVERTISSEMENT : Ne pas utiliser l’appareil tant que toutes les sections n’ont pas été assemblées et installées selon les
instructions du fabricant.
AVERTISSEMENT : Si cet appareil fonctionne sans être raccordé à un système d’évacuation correctement installé et
entretenu, ou si le système d’évacuation es modié, il peut en résulter un empoisonnement au monoxyde
de carbone et la mort.
SEULES DES PORTES CERTIFIÉES POUR CET APPAREIL DOIVENT ÊTRE UTILISÉES.
Utiliser uniquement avec l’écran no URP-891-0200. Suivre les instructions d’installation.
Fabrique au Canada par:
Archgard Industries Ltd.
7116 Beatty Dr., Mission, B.C.
novembre 2019 303-6060F-04
MODÈLE: UF0600 (SIT 885 Proflame)
MANUFACTURE DATE: 2019 2020 2021 JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC
date de fabrication: 2019 2020 2021 jan fév mar avr mai jun jul août sep oct nov dec
SAMPLE

7
Installation
5.0 Installation Checklist
This standard installation checklist is to be used by the installer in conjunction with, not instead of, the instructions contained
within this installation manual.
Customer: Date Installed:
Install Address: Location of Fireplace:
Installer:
Solid Fuel Zero Clearance Install: (Section 9.1) YES NO IF NO, WHY NOT?
Was the bottom of the existing zero clearance removed?
Was a 1/4" (6.35 mm) minimum clearance maintained as shown in
Figure 9.1.02?
Venting: (Section 13) YES NO IF NO, WHY NOT?
Venting conguration complies with vent diagrams.
Venting installed, fastened, and secured in place maintaining proper
clearances.
Secured or removed existing solid fuel replace damper.
Terminations installed and sealed in compliance with local building
code.
Direct vent termination is highest point in vent assembly.
Wiring / Electrical: (Section 7) YES NO IF NO, WHY NOT?
Connected to household 110/120v per local codes.
Unit is properly grounded.
Gas: (Section 11) YES NO IF NO, WHY NOT?
Proper appliance for fuel type?
Was a conversion performed?
Leak check performed & inlet and manifold pressures veried?
Was the rating of the insert clocked?
Finishing: YES NO IF NO, WHY NOT?
Only noncombustible material installed in noncombustible areas.
Clearances meet installation manual requirements.
Mantels and/or projections comply with install manual.
Was the solid fuel replace warning plate installed (Figure 9.0.02)?
Appliance Setup: YES NO IF NO, WHY NOT?
Burner media / log set, door, and screen installed according to install
manual.
Manual given to home owner.
Did you check operation of lights, fans, and ame modulation?
Comments:

8
Installation
6.0 Appliance Overview
6.1 Rating Plate Location
Figure 6.1.01: Figure 6.1.02:
6.2 Appliance Overview
Surround
Left Side Right Side
Information in this manual applies to both
the UF0600 and UF0610 unless otherwise
specied.
The Proame II control board is located on the
right side* of the replace behind the surround.
The valve is located on the left side* of the
replace behind the surround.
The fan is located on the inside of the rear
replace shell and can only be accessed from
the rear of the replace.
Note: This manual uses images of an unpainted
replace for the purposes of illustration.
*Left and right side references in this manual
correspond with the sides identied in Figure
6.2.01.
6.3 Leveling the Appliance
The UF0600 / UF0610 is equipped with front and rear leveling bolts.
The replace has the ability to independently level left/right and
front/back.
Leveling is done from the bottom of the unit
Figure 6.2.01:
Figure 6.3.01:

9
Installation
7.0 Electrical Connections
The UF0600 / UF0610 comes complete with an adjustable 6 speed fan and variable lights wired directly to the main control module.
Do not cut or remove the grounding prong from the main power supply plug.
CAUTION: Label all wires prior to disconnection when servicing.
NOTE: This appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes,
with the National Electrical Code, ANSI / NFPA 70, or the Canadian Electrical code, CSA C22.1.
6.4 Accessing the Control Board
The control board is located on the right side of the replace,
behind the replace surround. To access the control board:
1. Remove the surround (See Section 14.0).
2. Slide the control board forward as shown in Figure 6.2.01.
Ensure wires are not pinched or over-extended when moving the
control board.
Figure 6.4.01:

10
Installation
8.0 Appliance Dimensions
34.71
18.29
29.50
21.17
31.64
3 3
19.55
33.93
21.70
4.17
3.33
15.93
4.42
3.38
23.62
25.26
8.22
21.86
1:12
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 1
WEIGHT:
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED
DRAWN
VN
DATE
NAME
A
30/09/2016
UF0600/0610
PROPRIETARY AND CONFIDENTIAL
F:\UF0600
September-30-16 12:24:17 PM
SCALE
TOP
34.71
18.29
29.50
21.17
31.64
3 3
19.55
33.93
21.70
4.17
3.33
15.93
4.42
3.38
23.62
25.26
8.22
21.86
1:12
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 1
WEIGHT:
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED
DRAWN
VN
DATE
NAME
A
30/09/2016
UF0600/0610
PROPRIETARY AND CONFIDENTIAL
F:\UF0600
September-30-16 12:24:17 PM
SCALE
RIGHT SIDE
34.71
18.29
29.50
21.17
31.64
3 3
19.55
33.93
21.70
4.17
3.33
15.93
4.42
3.38
23.62
25.26
8.22
21.86
1:12
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 1
WEIGHT:
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED
DRAWN
VN
DATE
NAME
A
30/09/2016
UF0600/0610
PROPRIETARY AND CONFIDENTIAL
F:\UF0600
September-30-16 12:24:17 PM
SCALE
LEFT SIDE
34.71
18.29
29.50
21.17
31.64
3 3
19.55
33.93
21.70
4.17
3.33
15.93
4.42
3.38
23.62
25.26
8.22
21.86
1:12
SIZE
DWG. NO.
A
REV.
SHEET 1 OF 1
WEIGHT:
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
TO BE 90
UNLESS NOTED
OTHERWISE.
CHECKED
DRAWN
VN
DATE
NAME
A
30/09/2016
UF0600/0610
PROPRIETARY AND CONFIDENTIAL
F:\UF0600
September-30-16 12:24:17 PM
SCALE
FRONT
Exhaust Intake
Metric Equivalents
Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm
Front 3 76.2 18.29 464.6 34.71 881.6 21.17 537.7 29.5 749.3 31.64 803.7
Top 21.70 551.2 19.55 496.6 15.93 404.6 3.33 84.6 4.17 105.9 33.93 861.8
Left Side 4.42 112.3 8.22 208.8 3.38 85.9 25.26 641.6 23.62 599.9
Right Side 21.86 555.2

11
Installation
9.0 Minimum Opening Dimensions
WARNING: Failure to position the parts in accordance with these diagrams or failure to
use only parts specically approved with this appliance may result in property damage or
personal injury.
The installer must mechanically attach the marking supplied with the gas replace insert to the inside of the rebox of the replace into
which the gas replace insert is installed. See Figure 9.0.02.
Cutting of any sheet-metal parts of the replace, in which the gas replace insert is to be installed, is prohibited except as described in
Section 9.1.
If the factory-built replace has no gas access hole(s) provided, an access hole of 1 1/2” (38.1 mm) or less may be drilled through the
lower sides or bottom of the rebox in a proper workmanship-like manner. This access hole must be plugged with noncombustible
insulation after the gas supply line has been installed.
The replace ue damper can be fully blocked open or removed for installation of the gas replace insert.
The replace and replace chimney must be clean and in good working order and constructed of noncombustible materials. The
chimney clean-outs must t properly.
Refractory, glass doors, screen rails, screen mesh and log grates can be removed from the replace before installing the gas replace
insert.
Smoke shelves and ba󰀪es may be removed if attached by mechanical fasteners. Trim panels must not seal ventilation openings in the
replace.
WARNING: This replace has been converted for use with a gas replace insert only and cannot be used
for burning wood or solid fuels, unless all original parts have been replaced, and the replace
reapproved by the authority having jurisdiction.
AVERTISSEMENT: Ce foyer a ete converti pour utilisation avec un foyer au gaz encastrable et ne peut etre utiliser
pour bruler du bois ou autres combustibles solides a moins que toutes les pieces d'origine ete
remplacees et que le foyer ait ete approuve de nouveau par l'autorite competente.
303-0123
Figure 9.0.02:
AB
C
D
E
F
G
Reference Dimension
A24" (609.6 mm)
B 8.125" (206.4 mm)
C16" (406.4 mm)
D3.32" (84.3 mm)
E23.5" (596.9 mm)
F34.625" (879.5 mm)
G156.32°
Figure 9.0.01:

12
Installation
9.1 Factory Built Fireplaces
The following information applies to Factory Built (metal) Wood-Burning Fireplace installations:
Trim panels must not seal ventilation openings in the replace. Any parts that are removed must be saved and reinstalled if the insert
is ever removed. If the factory-built replace has no gas access hole(s) provided, an access hole of 1 1/2” (38.1 mm) or less may be
drilled through the lower sides or bottom of the rebox in a proper workmanship-like manner. This access hole must be plugged with
noncombustible insulation after the gas supply line has been installed.
The damper (A) and grate with logset (B) must be removed or fully blocked open.
The smoke shelf (C), internal ba󰀪es (D), screen ( E), masonry lining or refractory (G and I), and metal or glass doors (F) may be
removed.
The replace must be permanently marked to indicate that it has been altered and is no longer suitable for burning any fuel unless the
removed parts are reinstalled (See Figure 9.0.02). Cutting out of any metal parts is prohibited, except the metal oor (J) as specied.
The insulation (H), and any structured rigid frame member must not be removed or altered (side and top of door frame, side and top of
the face of replace, metal sides, etc.).
The metal oor of the rebox may be removed only if the following is strictly adhered to.
The metal oor (J) may be removed to allow additional room for installation of the insert as long as it does not compromise the
structural integrity of the existing replace and you maintain a mandatory minimum 1/4" clearance between the bottom of the insert and
the bottom shell of the existing replace. This may be achieved by using strips of noncombustible material or by using leveling bolts
on the insert (See Figure 9.1.02). If the oor is removed the insert must be placed directly on the metal base of the metal replace.
Under no circumstance can it be placed directly on a combustible material.
A
C
D
G
I
F
H
J
E
B
Figure 9.1.01: Side view of Factory Built (metal) Wood Burning
Fireplace.
Figure 9.1.02: Removing the Metal Floor
REMOVE THIS
SECTION OF
METAL FLOOR
REMOVE THIS
SECTION OF
METAL FLOOR
REMOVE THIS
SECTION OF
METAL FLOOR
Factory built
replace shell Factory built
replace
rebox
Remove this
section of
rebox oor
1/4" Minimum Clearance
(6.35 mm)

13
Installation
9.2 Refacing a Masonry Fireplace
Using Steel Studs and Cement Board on Wood Fireplaces
Brick or rock facing may be removed and replaced with noncombustible material such as steel studs and cement board.
WARNING: Only facing material may be removed. All other masonry material must not be cut out, chipped away, or removed.
WARNING: Louvers or any air circulation around existing solid fuel replace must not be blocked or covered.
The area between the masonry and the cement board must be sealed so that no heat can enter the open space between the masonry
of the wood replace and the refacing material. The insert must be moved outward so that the face of the replace is ush with
the nishing material.
Figure 9.2.01:
Original Wood Burning
Masonry Fireplace

14
Installation
10.0 Clearances to Combustibles
WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specically approved with this
appliance may result in property damage or personal injury or loss of life.
CAUTION: This appliance is designed for use in any masonry or factory-built, wood-burning replace. It cannot be enclosed by
combustible material and used as a factory built gas replace (zero clearance replace).
18”
2”
4”
6”
8”
10”
12”
20”
22”
24”
26”
28”
22 1/4”
Figure 10.1.01
10.1 Mantel Clearances
10.2 Sidewall Clearances
Figure 10.2.01
8"
(203.2 mm)
8"
(203.2 mm)
Maintain a minimum of 8" (203.2 mm) clearance
from the side of the door to sidewalls or mantel
supports.
Mantel clearances are measured
from the top of the appliance door.
Ensure combustible material is not
placed within the area shown.
(50.8 mm) A
(101.6 mm)
(152.4 mm)
(203.2 mm)
(254 mm)
(304.8 mm)
(565.2 mm)
Design
Specialties
Fronts
Archgard
Surrounds
(UA6000,
UA6100,
UA6200,
UA6300,
UA6400)
A18" (457mm) 9" (229mm)
B20" (508mm) 11"
(280mm)
C22" (559mm) 13"
(330mm)
D24" (610mm) 15"
(381mm)
E26" (661mm) 17"
(432mm)
F28" (711mm) 19"
(483mm)
BCDEF

15
Installation
10.3 Hearth Clearances
Non Combustible
Zone
16”
Non Combustible
Zone
16”
31 3/4”
Non Combustible
Zone
16”
Non Combustible
Zone
16”
31 3/4”
16”
16”
31 3/4”
Figure 10.3.01
Figure 10.4.01
(406.4 mm)
(806.5 mm)
(406.4 mm)
3.5"
(88.9 mm)
(406.4 mm) (406.4 mm)
(806.5 mm)
Combustible Zone
The Non Combustible
Zone may contain any
noncombustible material or
open air space. Never use
combustible materials within
the Non Combustible Zone.
10.4 Hearth Protection
Thermal protection
Thermal protection
Thermal Protection Specications
Minimum R value
is 1.4038 ft2•⁰F•hr @ 500°F
(200°C)
BTU
Combustible Zone
The insert may be installed closer to a combustible hearth if thermal protection is used. The thermal protection must be a non
combustible material that has an R value that is equal to or greater than 1.4038.
NOTE
All specied clearances must be maintained from the top surface of carpeting, tile, etc.
Any hearth that extends outward in front of the insert must not have any combustible material closer than 3.5" (88.9 mm) to the bottom
of the gas replace insert regardless of whether a noncombustible material covers the combustible material. This includes any type of
framing underneath a noncombustible material such as tile, marble, or stone. Any material farther than 3.5" (88.9 mm) to the bottom or
16" from the front of the door of the gas replace insert can be combustible.
WARNING
Failure to position the parts in accordance with these diagrams or failure to use only parts specically approved with this appliance
may result in property damage or personal injury.

16
Installation
11.0 Gas Connections
Before connecting the appliance to the gas supply line, double check that the appliance you have purchased is designed for the gas
type you are using. The gas type markings are located on the rating plate (See Section 4 and Section 6) and also on the appliance’s
gas valve.
Adequate clearance for proper installation and checking of the gas connections must be provided. All gas connections must be
checked for gas leaks.
Have your gas supplier or a qualied gas tter run a gas supply line into the solid fuel replace. The line must be properly sized and
tted according to the installation codes. Immediately upstream of the supply connection, the tter shall provide an accessible manual
shut-o󰀨 valve. When connecting the supply line to the gas valve, the installer shall brace the gas valve to ensure that the gas valve is
not moved from its bracket. If the valve is not braced when the supply line is connected, the valve may be moved and cause a “break”
in the main burner supply line. Such damage is not covered by the manufacturer’s warranty.
CAUTION: The appliance and its individual shut-o󰀨 valve must be disconnected from the gas supply piping system during any
pressure-testing of that system at test pressures in excess of 1/2 psig (3.5 kPa). The appliance must be isolated from the gas supply
piping system by closing its individual manual shut-o󰀨 valve during any pressure-testing of the gas supply piping system at test
pressures equal to or less than 1/2 psig (3.5 kPa). Failure to do so will damage the appliance’s gas valve. Such damage is not covered
by the manufacturer’s warranty.
Natural Gas Pressure Settings:
The inlet supply or line pressure must be a minimum of 5.0” W.C. (1.2 kPa) and a maximum of 14.0" W.C. (3.5 kPa). The orice is a
#31 DMS (3.05 mm) drill size.
ELEVATION INPUT RATING
0-4500 ft (0-1372 M) 40,000 BTU/hr (11.72 kW)
4500 ft (1372 M) and above. 40,000 BTU/hr (11.72 kW) less 4% per 1000 ft. (305 M) above sea level.
Please contact your local distributor for the appropriate orice size you require.
Propane Pressure Settings:
The inlet supply or line pressure must be a minimum of 12.0” W.C. (2.7 kPa) and a maximum of 14.0” W.C. (3.5 kPa). The orice is a
#47 DMS (1.99 mm) drill size.
ELEVATION INPUT RATING
0-4500 ft. (0-1372 M) 40,000 BTU/hr (11.72 kW)
4500 ft. (1372 M) and above. 40,000 BTU/hr (11.72 kW) less 4% per 1000 ft. (305 M)
Please contact your local distributor for the appropriate orice size you require.
11.1 Clocking Procedure
IMPORTANT: THE INPUT RATING SHOULD ALWAYS BE CHECKED WHEN FIRST FIRING THIS APPLIANCE.
Before you begin, shut o󰀨 all other gas appliances including any standing pilots. Light the replace and wait 15 minutes. Clock the
time to burn 1ft³ of gas on the meter. Check with your gas supplier for the gas BTU content at your elevation. Input is the rate of ow
multiplied by the heating value of the gas (cubic feet/hour x BTU per cubic feet). Note: This assumes a dry gas meter at 1/2 psi. If using
a 2 psi dry gas meter the unit will rate lower as the calculation has to correct for the higher pressure in the meter. If the unit is over-
rated, contact your authorized Ambiance dealer. The following calculation equation gives a rough estimation as it does not correct for
temperature and pressure.
Rough Calculation Equation:
3600 Xgas caloric value
in BTU/ft3= Rating in BTU
time to burn 1ft3
gas in seconds hr

17
Installation
12.0 Conversion Kit Instructions
IMPORTANT: This replace is Natural gas ready. If converting to LP gas, follow instructions below.
WARNING: This conversion kit shall be installed by a qualied service agency in accordance with the manufacturers instructions
and all applicable codes and requirements of the authority having jurisdiction. If the information in these instructions is not
followed exactly, a re, explosion or production of carbon monoxide may result, causing property damage, personal injury or loss
of life. The qualied service agency is responsible for proper installation of this kit. The installation is not proper and complete
until operation of the converted appliance is checked as specied in the instructions supplied with the kit. Refer to appliance
owner’s manual or product data plate for proper inlet and manifold pressure adjustments and orice sizing.
IMPORTANT: For high altitude installations above 4500 ft (1372 meters), consult local gas distributor or the authority having
jurisdiction for proper derating methods.
KIT NUMBERS: UA1400 for LP gas and UA1500 for Natural Gas
KIT INCLUDES:
• Gas conversion label (303-0128)
• Burner orice (part number 301-0068-47, #47 DMS for LPG) (part number 301-0068-31, #31 DMS for NG)
• Instruction Sheet
• SIT 885 Valve conversion kit c/w instructions & gas type label
WARNING: SHUT OFF GAS SUPPLY AND ELECTRICAL POWER TO FIREPLACE
SHUT OFF GAS SUPPLY BEFORE DISCONNECTING ELECTRICAL POWER
12.1 Prepare the Fireplace
Remove the surround, barrier screen, glass frame assembly, logs or glass media, embers and brick panels or rebox liner (if
applicable)*.
Remove the burner*.
*See relevant sections in this manual.
Remove the burner orice using a 1/2” wrench. Replace with the orice
supplied with the conversion kit. Use a small amount of pipe sealant on
the threads of the orice mount. Do not use too much as it can block the
orice.
12.2 Pilot Conversion
Using a 7/16” wrench and loosen the pilot hood 1/4 turn.
Slide the tab at the bottom of the orice hood all the way
so the red side (propane) with the hole in it is showing.
Tighten the pilot hood back up so that it is lined up with
the two probes on both sides of the pilot assembly.
Figure 12.1.01:
Figure 12.2.01:

18
Installation
12.4 Complete the Conversion
• Reinstall the burner, brick liners or rebox liner, logs or glass media, embers, and glass door*
• Turn on the gas and electrical supplies
• Turn on the replace so the burner is on
• Check for leaks at all connections
Test inlet and outlet pressure (See Section 3.3). Visually check pilot ame. Flame should envelope top of the ame sensor and extend
forward onto the burner. To adjust pilot turn the pilot adjustment screw on the control valve clockwise to decrease or counter clockwise
to increase pilot ame. Clock the rating as shown in Section 11.1. Adjust the primary air according to specications in this manual or as
found on the rating plate.
• Turn replace o󰀨
• A󰀩x gas type label to the rating plate label (See Section 6.1 for rating plate location)
• Complete the conversion label and a󰀩x to valve assembly plate
• Reinstall the barrier screen and surround*
*See relevant sections in this manual.
12.3 Convert the Gas Valve
WARNING: Installation of this conversion kit must only be undertaken by a
qualied and certied gas appliance installer.
Verify that the following items are present in the package:
• Pressure regulator assembly (E)
• Two (2) screws (F)
• Identication label (G)
• Installation instructions (this document)
1. Shut o󰀨 the gas supply to the valve and shut down the electric supply.
2. See Figure 12.3.01. Using a Torx T20, or slotted screwdriver, remove
and discard the two (2) pressure regulator mounting screws (A), pressure
regulator tower (B), and the spring and diaphragm assembly (C), (If
applicable).
3. Ensure the rubber gasket (D), which is pretted as part of assembly (E),
is properly positioned, see Figure 12.3.02, otherwise t the gasket as
shown Figure 12.3.02.
4. Install the new STEPPER MOTOR pressure regulator assembly, as
shown in Figure 12.3.03 and Figure 12.3.04. Use the supplied screws
(F), M4 x 0.7 threaded, length of thread L=( 16 mm + 0 - 0.5 mm ), steel
material, resistance class 8.8 (see Figure 12.3.05).
5. Manually thread the two conversion kit mounting screws into the valve
body. Use a standard screwdriver or T20 Torx bit and tighten to the
screws with a xing torque of 25lb-in ± 5%.
IN THE EVENT THAT THE THREADS OF THE VALVE ARE STRIPPED
OR DAMAGED, REPLACE THE VALVE.
6. Install the enclosed identication label (G) to the valve body where it can
be easily seen.
7. Make STEPPER MOTOR and valve electrical connections, apply gas to
system and relight appliance according to manufacturers instructions.
8. With the main burner "ON", test the new pressure regulator assembly for
leaks using a soap solution.
9. Relight the main burner and verify proper burner ignition and operation.
WARNING: Installation should be carried out in a clean environment.
WARNING: This modulating conversion kit must ONLY be applied as part of a conversion kit supplied by the APPLIANCE
MANUFACTURER.
WARNING: Correct operation of the system cannot be guaranteed if the conversion kit or valve has been dropped or has
sustained a strong impact.
INSTALLER NOTICE: These instructions must be left with appliance.
Figure 12.3.01:Figure 12.3.05:
Figure 12.3.03:
Figure 12.3.02:
Figure 12.3.04:

19
Installation
13.0 Venting Instructions
WARNING: Operation of this heater when not connected to a properly installed and maintained venting system can result
in carbon monoxide (CO) poisoning and possible death. The appliance must not be connected to a chimney ue serving a
separate solid fuel burning appliance.
CAUTION
Only approved 3” (76mm) double wall aluminum or stainless ex liners and approved vent terminals are to be used for this appliance.
13.1 Approved Terminations
Archgard Venting Components
Vent Component Part Number
Vertical Termination 999-INS-TK
3" x 30' Aluminum Flex Liner 999-INS-FL330
3" x 50' Aluminum Flex Liner 999-INS-FL350
Approved venting components from third party manufacturers may be
found on the following page.
This appliance is designed for dual 3” (76 mm) double wall aluminum ex liner. The liner must run the entire length of the chimney from
the appliance to the termination.
The ue length must be a minimum of 10’ (3.05 M) and a maximum of 40’ (12.2 M) from the top of the gas replace insert.
Masonry chimneys may take various contours which the exible liner will accommodate, however, keep the exible liner as straight as
possible, avoiding unnecessary bending but at all times keep a minimum of 3” (76 mm) inside bend radius.
The Air Intake Flex Liner must be connected to the inlet air collars
of the termination cap and the appliance.
The Exhaust Flex Liner must be connected to the exhaust collars of
the termination cap and the appliance.
The Air intake and Exhaust connections are marked on the gas
appliance. See Figure 13.1.01.
DO NOT REVERSE THESE CONNECTIONS
CAUTION
To ensure that the venting is not accidentally obstructed or
punctured, the damper of the host replace must be permanently
disabled by either complete removal of the damper, or by being
fully blocked open, for the installation of a gas replace insert.
Figure 13.1.01: Intake & Exhaust as viewed from back of
replace.
Intake
Exhaust

20
Installation
Third Party Venting Components
BDM Selkirk Duravent ICC Amerivent
3" Flex (10ft) 95270310 AFE10-03 N/A N/A 3ALKE10
3" Flex (25ft) 95270325 AF3-25L 3DFA-25 N/A 1730250
3" Flex (30ft) 95270330 N/A N/A N/A N/A
3" Flex (35ft) 95270335 AF3-35L 3DFA-35 TC-AL35 1730350
3" Flex (50ft) 95270350 N/A N/A TC-3AL50 3ALKE50
3" Flex Coupling 95090390 AF3-FC 3DFA-FC TM-CFAA3 Comes with
4x6 5/8 Coaxial High Wind
Cap 940285 4DT-VC 46DVA-VCH TM-4SVT N/A
4x6 5/8 Coaxial Low-Prole
Cap 940206LP 4DT-VT N/A N/A 4DVC
3x3 Colinear to 4x6 5/8
Coaxial Adapter 940113364 4DT-CBT, 4DT-AAC 46DVA-GK TM-CTA 4DCAT33
High Wind Shield Round P94000339 N/A 46DVA-VWG TM-SVTS N/A
High Wind Shield
Rectangular N/A N/A N/A TM-CTS N/A
Co-linear High Wind Vert
Term Kit (with 35 ft. Flex) for
Masonry Chimney
94203370HWS 1604645 46DVA-CL33 TM-ALK33 DVIK33 (Not High
Wind)
Co-linear Direct Vent Facto-
ry Built Reline Kit High Wind
Vert Term (with 35ft Flex) N/A N/A 46DVA-CL33KFB TC-AL35, TM-IVT,
TM-IVTP N/A
3x3 Co-linear Round Vert
Term 940033HWS 1604643 N/A TM-IVT DVCC33
3x3 Co-linear High Wind
Vert Term Round Base 9400332RD N/A N/A TM-IVT, TM-IVTP N/A
3x3 Co-linear High Wind
Vert Term Square Base 940033HWS N/A N/A TM-IVT, TF-MFR, TF- MFC, TF-MF N/A
Co-linear Masonry Flashing
Rectangular Vert Term N/A N/A N/A TF-CTF, TF-CTFC N/A
3x3 Co-linear Square Vert
Term
940033,
9400330808SS N/A N/A N/A N/A
3x3 Co-linear Rectangular
Vert Term 940034EC26SS N/A N/A TM-CT3 N/A
Co-linear Masonry Flashing
Rectangular Vert Term N/A N/A N/A TF-CTF, TF-CTFC N/A
Prefab Chimney Flashing N/A N/A N/A TM-IVTP N/A
3" Appliance Co-linear Flex
Connector N/A 4DT-CFC 46DVA-ADF N/A N/A
3x3 Co-linear Square
Double Cap 940033DBL N/A N/A N/A N/A
ATTENTION
NO OTHER VENTING SYSTEM OR COMPONENTS MAY BE USED.
Part numbers shown are correct at the time of printing and should be conrmed with the manufacturer prior to purchase.
Follow manufacturer instructions for installation of termination.