Ambiance Fireplaces Intrigue 42 User manual

200-U110-13
January 20, 2021
MODEL: UF0110
GAS FIRED DIRECT VENT FIREPLACE
S/N 610072 AND UP
ARCHGARD FIREPLACE PRODUCTS
7116 Beatty Drive
Mission, BC V2V 6B4 Canada
English and French Installation Manuals available through your
local dealer or visit our website at: www.archgard.com
Les manuels d'installation en anglais et en français son
disponibles chez votre détaillant local ou en visitant notre site
web: www.archgard.com
INSTALLER:
LEAVE THIS MANUAL WITH THE APPLIANCE.
CONSUMER:
RETAIN THIS MANUAL FOR FUTURE REFERENCE.
This appliance may be installed in an aftermarket
permanently located, manufactured home (USA only) or
mobile home where not prohibited by local codes.
This appliance is only for use with the type of gas indicated
on the rating plate. This appliance is not convertible for use
INSTALLATION, OPERATION, AND
MAINTENANCE MANUAL
liquids in the vicinity of this or any other appliance.
- WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance
• Do not touch any electrical switch; do not use any
phone in your building
• Leave the building immediately
• Immediately call your gas supplier from a neighbor's
phone. Follow the gas suppliers instructions
•
department
installer, service agency or the gas supplier.
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in
serious injury, death, or property damage.
76.38%
Based on CSA P.4.1-15

2
TABLE OF CONTENTS
Introduction 3
Safety Information 4
Technical Information 5
5
Installation Codes 5
5
High Altitude Installation 5
Rating Plate Sample 6
Installation Checklist 7
SPECIFICATIONS 8
FIREPLACE DIMENSIONS 8
UF0110 COMPONENTS LIST 9
INSTALLATION OVERVIEW 9
PREPARE THE FIREPLACE 10
10
Horizontal Vent Heat Shield Installation
11
11
FRAMING 12
Wall Enclosure Rough Opening 12
Min. Finished Opening Dimensions 12
Optional Full Door Face Dimensions 13
Framing 13
Horizontal Terminations 14
Vertical Terminations 14
TYPICAL INSTALLATION OPTIONS 15
Typical Horizontal Installation 15
Typical Corner Installation 15
Typical Vertical Installation 15
MANTEL REQUIREMENTS 16
16
GRILL SET 17
Glass Door Removal and Installation 18
UF0110 SAFETY BARRIER 19
GAS LINE CONNECTION 20
Gas Conversion 20
Electrical Connections 20
VENTING 21
Approved Venting 21
Horizontal Terminations 21
Horizontal Terminations 22
Vertical Terminations 22
Termination Vent Cap Location 24
Location Clearances 24
Vent Termination Clearances 25
LIGHT INSTALLATION 26
REFLECTIVE PANEL KIT 27
REFRACTORY PANEL KIT 29
MEDIA INSTALLATION 31
Glass Bead Installation 31
Mississippi River Rock Installation 33
WIRING SCHEMATICS 35
PRESSURE TESTING 36
37
CONTROL SYSTEM COMPONENTS 39
SYSTEM OPERATION 40
Initializing the System 40
Temperature Display 40
Turn on the Appliance 40
40
Manually Control Flame 40
Room Thermostat 41
Smart Thermostat 41
Fan Speed Control 41
Accent Light Kit 41
Key Lock 41
Low Battery Detection 42
Continuous Pilot / Intermittent Pilot 42
Reset System for Manual Operation 42
Automatic Safety Restart 42
43
LIGHTING AND SHUTDOWN 44
Maintenance 46
Cleaning and Routine Maintenance 46
Pressure Testing 47
18.3 Flame Appearance 48
49
Refractory Panel Kit Removal 51
Burner Removal 52
Burner Installation 53
54
CONVERSION KIT INSTRUCTIONS 55
REPLACEMENT PARTS LIST 59
LIMITED WARRANTY 60
LIFETIME WARRANTY 61

3
General Information
Introduction
The UF0110
Some of the many features of your UF0110
•
•
less expensive to operate.
•
•
and heating needs.
•
• Solid Construction
• Optional Accessories
• Multiple Electronic
Pilot Settings
system (also known as a Pilot on Demand (POD)).
CPI vs IPI:
Continuous Pilot on Demand Ignition (CPI)
Intermittent Pilot Ignition (IPI)
www.archgard.com/warranty-registration

4
General Information
Caution
FOR YOUR SAFETY - Do not install or operate your UF0100 without reading and understanding this manual. Any installation or
operational deviation from this instruction manual voids the warranty and may prove hazardous.
•
•
•
• Provide adequate clearances for proper operation and servicing of the appliance
•
•
• Always provide adequate clearance around the intake and exhaust openings
Safety
•
•
•
installed on a metal or wood panel extending the full width and depth of the appliance
•
individuals out of the room and away from hot surfaces
•
•
• WARNING:
•
•
clean
•
•
•
• California Proposition 65 Warning:
•
heater and to document any deviations from a typical install.
Any alteration to the product that causes carbon or soot deposits that results in any damage or requires cleaning is not the
responsibility of the manufacturer.
Safety Information

5
General Information
Technical Information
A copy is shown on the following page.
Commonwealth of Massachusetts
Please contact Archgard Industries Ltd
Installation Codes
National Fireplace Institute® (NFI) as NFI Gas Specialists.
Natural Gas (NG) Propane (LP)
Manifold Pressure
Min. Supply Pressure
Max Supply Pressure
Input Rating
(FE) 76.38% 78.27%
76.65% 80.23%
Electrical Rating
Gas Control
Altitude
Primary Air Opening
High Altitude Installation

6
General Information
DO NOT REMOVE THIS LABEL
LISTED VENTED GAS FIREPLACE HEATER and GAS-FIRED APPLIANCES FOR USE AT HIGH ALTITUDES.
Tested to: ANSI Z21.88-2014 / CSA 2.33-2014, CAN/CGA 2.17-M91 (R2009), CSA P.4.1-15, CSA C22.2 No.3 - M1998(R.2014).
VENTED GAS FIREPLACE HEATER-NOT FOR USE WITH SOLID FUEL.
NG LPG
(5.86 - 10.84 kW) (5.57 - 10.84 kW)
1.1 - 3.8 in. W.C. (0.3 - 0.9 kPa) 2.9 - 11.0 in. W.C. (0.7 - 2.73
kPa)
#31 DMS (3.05 mm dia.) #50 DMS (1.78 mm dia.)
5.0 - 14.0 in. W.C.
(1.2 - 3.5 kPa)
12.0 - 14.0 in. W.C.
(2.9 - 3.5 kPa)
76.38% 78.27%
HOR: ALL SIDES: 1” (25MM) VERT: 1” (25MM)
VENTING REQUIREMENTS:
(229mm)
21.5” (546mm)
ONLY DOORS CERTIFIED WITH THE APPLIANCE SHALL BE USED.
MANUFACTURE DATE: 2019 2020 2021 JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC
UF0110
Rating Plate Sample

7
General Information
Installation Checklist
This standard installation checklist is to be used by the installer in conjunction with, not instead of, the instructions contained
within this installation manual.
Customer: Date Installed:
Install Address: Location of Fireplace:
Installer:
Appliance Install: YES IF NO, WHY NOT?
Fireplace is leveled and secured.
Venting: YES IF NO, WHY NOT?
Venting installed and secured in place maintaining proper clearances.
Wiring / Electrical: YES IF NO, WHY NOT?
Connected to household 110/120v per local codes.
Unit is properly grounded.
Gas: YES IF NO, WHY NOT?
Proper appliance for fuel type?
Was a conversion performed?
Finishing YES IF NO, WHY NOT?
Clearances meet installation manual requirements.
Mantels and/or projections comply with install manual.
Appliance Setup: YES IF NO, WHY NOT?
manual.
Manual given to home owner.
Comments:

8
Installation
SPECIFICATIONS
FIREPLACE DIMENSIONS
DESCRIPTION Height Width Back
Width
Depth Opening
Width
Glass
Frame
Height
Height
Front
to Vent
Center
(Vert.
Term.)
Floor
to Vent
Center
(Hor.
Term.)
Front to
Angled
Back
FIREPLACE
DIMENSIONS
INCHES 34-1/2 40-7/8 30-7/8 19-3/8 35-1/2 26-5/8 10 16-1/8 33-3/8 8-1/8
MILLIMETERS 876 1038 785 493 902 676 254 410 848 206
WARNING
772mm
206mm
902mm

9
Installation
UF0110 COMPONENTS LIST
DESCRIPTION
Burner Media (purchased separately)
Remote Control
Light Kit
Fan Kit
NOTE
the installation.
NOTE
or the Canadian Electrical Code CSA C22.1.
1.
2. -
place.
3.
4.
5.
6. Complete electrical hook-up. Install any standard or optional electrical components.
7. Complete gas line installation.
8. Complete venting installation.
9.
10.
11.
12.
13. Install grills and optional decorative doors / faces.
14.
PLACEMENT CLEARANCE REQUIREMENTS
•
•
•
•
•
•
INSTALLATION OVERVIEW

10
Installation
PREPARE THE FIREPLACE
WARNING
Use only non-combustible material in
Do not Other clearances apply. All clearances must
1.
2.
3.

11
Installation
IMPORTANT
1.
2. Bend horizontal heat shield at perforation to a 45° angle. Slide (3) slots on
horizontal vent heat shield under loosened screws. Re-tighten screws.
1.
2.
3.
4.
NOTE CAUTION

12
Installation
FRAMING
Wall Enclosure Rough Opening
IMPORTANT
size as necessary to maintain at least minimum clearance requirements.
Non –combustible facing material
Min. Finished Opening Dimensions
NOTE WARNING
Provide adequate clearances around air openings into the
creating a potentially hazardous situation.

13
Installation
Optional Full Door Face Dimensions
NOTE
-
-
Framing
NOTE
faces.
WARNING
FIRE
HAZARD
IMPORTANT
WARNING DO NOT RECESS VENT CAP INTO WALL OR SIDING.

14
Installation
Follow vent pipe manufacturer’s installation instructions for horizontal terminations.
Include required vent manufacturer’s wall pass-thru clearances when determining
framing dimensions.
MINIMUM HORIZONTAL FRAMING DIMENSIONS
VENT PIPE CENTER (A) FRAMED OPENING TOP (B)
RIGID PIPE
requirements
FLEX PIPE
requirements
Vertical Terminations
Follow vent pipe manufacturer’s installation instructions for vertical terminations.
maintained.
NOTE
CAUTION
-
cold air from entering.
CAUTION -
eries.
HEARTH HEIGHT
W
H
B
A

15
Installation
TYPICAL INSTALLATION OPTIONS
IMPORTANT
Typical Corner Installation
Typical Vertical Installation

16
Installation
MANTEL REQUIREMENTS
WARNING TOP STAND-OFF BRACKETS MUST BE ASSEMBLED AND ATTACHED TO FIREPLACE. DO NOT REMOVE.
STAND-OFF BRACKETS ARE NOT LOAD BEARING
Non-Combustible Zone:
Rigid Pipe
Flexible Venting
HORIZONTAL VENT HEAT SHIELD

17
Installation
GRILL SET
Installation
1.
face. Set down into position.
2.
3. Partially thread (2) screws (included in components
packet) into nuts at each end of lower grill. Secure to
controls.
Removal
1.
clips.
2. Lift upper louver up and out of slots.
3. Remove screws securing lower grill at each end to

18
Installation
Glass Door Removal and Installation
WARNING:
permanently. Inspect the door gasket to ensure no damage has occurred when installing the glass door.
If Your Glass Breaks NOTE: the NEW door will emit some odor when the appliance
is lit. The odor will dissipate after the gasket material within the
permanently.
Warning:
Remove Glass Frame Assembly
1.
2.
3.
4.
PULL OUT AND DOWN TO RELEASE PULL OUT AND UP TO RELEASE
FIREPLACE BOTTOM FIREPLACE TOP
Install Glass Frame Assembly
Installation is the reverse of removal.
1. Pull top handles out and down to secure glass frame
2.
Note:
centered on install.
Door center pins

19
Installation
UF0110 SAFETY BARRIER
UF0100/110-BS).
WARNING
DO NOT INSTALL THE BARRIER SCREEN WITH THE GLASS DOOR REMOVED.
• REMOVE TOP GRILL AND HOOD
• OPEN BOTTOM GRILLS
•
• REMOVE SCREEN
TO REINSTALL THE BARRIER SCREEN, REVERSE THE
STEPS FOR REMOVAL.

20
Installation
GAS LINE CONNECTION
Gas Conversion
separately).
Note:
Note: LP (propane) installations require removal of the restrictor under certain vent runs. See venting section for further information.
CAUTION
NOTE connect.
any pressure testing of that system at pressures in excess of 1/2 psi (3.5 kPa).
during any pressure testing of the gas line at test pressures equal to or less than 1/2 psi (3.5 kPa).
methods.
IMPORTANT operating conditions and was determined independently of any installed system.
Electrical Connections
The UF0110
remove the grounding prong from the main power supply plug.
CAUTION:
NOTE:
•
•
• Remove Bottom Grill Set
Step 1: Step 2:
to local code and install the cover plate provided with the
the receptacle.