Ambiance Fireplaces Intrigue UF0100 User manual

#UF0100
ARCHGARD FIREPLACE PRODUCTS
7116 BEATTY DRIVE
MISSION , BC V2V 6B4 CANADA
200-U100
www.archgard.com
www.archgard.com
Effective August 20 2015
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE
This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or mo-
bile home where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate.
This appliance is not convertible for use with other gases, unless a certified kit is used.
WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result,
causing property damage, personal injury or loss of life.
WHAT TO DO IF YOU SMELL GAS:
 Do not light any appliance
 Do not touch any electrical switch: do not use any phone in your building.
 Immediately call your gas supplier from a neighbors phone.
 Follow the gas suppliers instructions.
 If you can not reach your gas supplier, call the fire department.
Do not store or use gasoline or other flammable
vapors or liquids in the vicinity of this or any
other appliance.
Installation and service must be performed by a
qualified installer, service agency or the gas
supplier

2

3
1
Burner Removal
Burner Installation
Burner

4
This fireplace has been listed by LABTEST Certification Inc to the following USA and Canada gas appliance standards
2
ANSI Z21.88-2014/CSA 2.33-2014 “Standard for Vented Gas Fireplace Heaters.”
CAN 2.17-M19 (R2009), “Gas-Fired for Use at High Altitudes.”
CAN/CSA P.4.1-09, “Testing Method for measuring Annual Efficiency
The glass assembly, shall only be replaced as a complete unit, as supplied by Archgard Industries Ltd.
DO NOT SUBSTITUDE ANY MATERIALS

5
3

6
30-7/8
785
19-3/8
493
8-1/8
210
8
6
9”
4
229mm
173mm

7
UF0100
5

8
6

9
7

10
FRAMING
WALL ENCLOSER ROUGH OPENING
IMPORTANT
Framing dimensions should allow for wall covering thickness and fireplace facing materials. If using a hearth, adjust rough
opening size as necessary to maintain at least minimum clearance requirements.
Non –combustible facing material may be applied over (but not directly to) fireplace face. This will prevent facing material from
falling off due to heat expansion. Do not obstruct the flow of ventilation air.
MINIMUM FINISHED OPENING DIMENSIONS
HORIZONTAL TERMINATION: 44-1/2” (1130mm) HIGH x 41-7/8” (1051mm) WIDE x 21-1/2” (546mm) DEEP.
1/2” (13mm) clearance back and sides of fireplace must be maintained.
VERTICAL TERMINATION: 44-1/2” (1130mm) HIGH x 41-7/8” (1051mm) WIDE x 21-1/2” (546mm) DEEP.
1/2” (13mm) clearance back and sides of fireplace must be maintained.
NOTE
Provide adequate clearance in front of fireplace to operate lower grill, open and close optional full door face doors, access
Components, installation of gas line, fan, etc. See figure 8b
WARNING
PROVIDE ADEQUATE CLEARANCES AROUND AIR OPENINGS INTO THE COMBUSTION CHAMBER
DO NOT OBSTRUCT UPPER AND LOWER GRILL OPENINGS. ROOM AIR ENTERS THROUGH LOWER PASSAGE, IS
HEATED AND EXITS THROUGH UPPER PASSAGE. BLOCKING THESE PASSAGES MAY RESULT IN OVERHEATING,
OPTIONAL FULL DOOR FACE DIMENSIONS
If installing an optional full door face, please refer to below for full
face dimensions before applying facing material.
NOTE
Consider height of hearth finish material (stone, brick, marble
etc.) when building fireplace platform. Bottom of fireplace
must be level with finished hearth to allow for lower grill
operation and proper fit of optional decorative full door faces.
1/2” (13mm) side overlap applies to both sides of face. Illus-
trations show True Dimensions. We recommend 1/4” (6mm)
clearance on all sides to allow for uneven finish material.
8
41-7/8”
(1064mm)
41¾
1060 mm
36 5/32
918 mm

11
FRAMING
Determine exact position of your fireplace, including hearth height, width, and depth (if applicable). If possible, place fireplace in
such a manner that vent termination will be between two studs, eliminating the need for additional framing.
If masonry is to be used (optional), prepare the necessary foundation for the masonry load. When masonry construction is used, a
lintel must be used over top of fireplace to support the added weight.
Build hearth to desired size and height. If a hearth extension is desired, combustible material may be used.
NOTE
Consider height of hearth finish material (stone, brick etc.) when building fireplace platform. Bottom of fireplace must be
level with finished hearth to allow for lower grill operation and proper fit of optional decorative full door faces.
WARNING
Install fireplace on hard metal or wood surface extending the full width and depth of fireplace.
Minimum platform size: 41-7/8” (1064mm) x 19-3/8” (493mm)deep.
FIRE
HAZARD
DO NOT install directly on carpet, vinyl, or any combustible material other than wood.
IMPORTANT
Vent cap location must be in compliance with guidelines on page 16 of this manual.
DO NOT RECESS VENT CAP INTO WALL OR SIDING.
WARNING
HORIZONTAL TERMINATIONS
Follow vent pipe manufacturer’s installation instructions for horizontal
terminations. Include required vent manufacturer’s wall pass-thru clearances
when determining framing dimensions.
MINIMUM HORIZONTAL FRAMING DIMENSIONS
VENT PIPE CENTER (A) FRAMED OPENING TOP
(B)
RIDGID PIPE 33-3/8” (848mm) Per vent manufacturer’s re-
quirements
FLEX PIPE 36-7/8” (973mm) Per vent manufacturer’s re-
quirements
VERTICAL TERMINATIONS
Follow vent pipe manufacturer’s installation instructions for vertical
terminations. A minimum of 1” (25mm) clearance on all sides of vertical
vent pipe must be maintained.
NOTE
The included Horizontal Vent Heat Shield is not used for vertical configurations.
CAUTION
Cold air transfer area. The surrounding fireplace chase must comply with all clearances as outlined in this manual and be
constructed in compliance with local building codes. Outside walls should be insulated to prevent cold air from entering.
CAUTION
Due to high temperatures, this fireplace should be located out of traffic areas and away from furniture and draperies.
9

12
10

13
11
SNOKEL TERMINATION

14
#56 & #33 #62 & #49
12
7" WC (1.74 kPa)
10” WC (2.49 kPa)
11” WC (2.74 kPa)

15
VENTING
WARNING
Consult the local and international codes to assure adequate combustion and ventilation air is available.
Flame height and appearance will very depending upon venting configuration and type of fuel used.
Venting requirements apply to both Natural and LP gas.
Refer to the vent manufacturer’s installation manual for complete installation instructions.
Installation must conform with the venting requirements and restrictions as outlined in this manual.
Provide a means for visually checking vent connection to fireplace after fireplace is installed.
APPROVED VENTING
Simpson Dura-Vent DV-GS 5” x 8” and 4” x 6-5/8” with reducer (horizontal and vertical terminations).
Metal Fab Direct Chimney Systems 5” x 8” (horizontal and vertical terminations).
ICC Direct Chimney Systems 5” x 8” (horizontal and vertical terminations).
Selkirk-Metalbestos Chimney Systems 5” x 8” and 4” x 6-5/8” with reducer (horizontal and vertical terminations).
BDM 5” x 8” Chimney Systems, flex and rigid (horizontal and vertical terminations).
Security 5” x 8” Chimney Systems (horizontal and vertical terminations).
Ameri-Vent 5” x 8” Chimney Systems (horizontal and vertical terminations).
HORIZONTAL TERMINATIONS
HORIZONTAL VENT SYSTEM CLEARANCES
TOP BOTTOM SIDES
ALL APROVED VENTING 2 INCHES (25mm) 1 INCH (25mm) 1 INCH (25mm)
HORIZONTAL MIN. / MAX.
MINIMUM: 45º elbow + 6"- 24" Pipe (152mm - 609mm) + snorkel termination cap.
MAXIMUM: 45º elbow + 1ft. Pipe (305mm) + 90º elbow + 3 ft. pipe (914mm) + snorkel termination cap.
HORIZONTAL MIN. / MAX. (with reducer)
NAT GAS MINIMUM: 2ft. (610mm) vertical + reducer + 90º elbow + 6” (152mm)horizontal + termination cap.
NAT GAS MAXIMUM: 2ft. (610mm) vertical + reducer + 90º elbow + 12ft. (3.66m) + termination cap.
LP GAS MINIMUM: 2ft. (610mm) vertical + reducer + 90º elbow + 6” (152mm) + termination cap.
LP GAS MAXIMUM: 2ft. (610mm) vertical + reducer + 90º elbow + 2ft. (610mm) + termination cap.
LP GAS MAXIMUM: 3ft. (914mm) vertical + reducer + 90º elbow + 12ft. (3.66m) + termination cap.
IMPORTANT
Wall pass-thru required for all horizontal runs. Refer to vent manufacturer to determine which pass-thru will work best
for your application and wall thickness.
The horizontal vent shield must be installed when using a 45º elbow to horizontally position the vent system.
Exception: corner installations.
ELBOWS
The following statement applies to horizontal, vertical, or a combination of horizontal / vertical elbows:
For each additional 90º elbow used after the first elbow, 3ft. (914mm) must be subtracted from the maximum allowed venting. For
each 45º elbow used, 1-1/2ft. (457mm) must be subtracted from the maximum venting allowed.
NOTE
(2) 45º degree elbows may be used in place of (1) 90º elbow.
13

16
14
Minimum 6” (152mm)
Maximum 24” (609mm)
3ft. (915mm)
3ft. (915mm)
3ft. Pipe
1ft. Pipe
45º Elbow
90º
Elbow
Snorkel
Termination
Snorkel
Termination

17
15
0-
8-
12-
16-
20-
24-
28-
30-
2-
6-
4-
10-
14-
18-
22-
26-
32-
50-
48-
46-
44-
42-
40-
34-
36-
38-
42 60 8 16
10 12 14 18 20 22 24 26 28 30
1’
Note: Horizontal venting 3ft and
under, must use a snorkel style
termination.

18
16

19
17

20
UF0100 LOG SET INSTALLATION
18
Black Embers should be placed in open areas and as not to completely block burner ports.